RA 10 460/03.

95

Variable Volume Vane Pump Model V4 Extracted from

(Series 2X, 3X, 4X) with Control Program RA
...2320 PSI …1.22 to 7.63 in3/rev
10 460/03.95
Sizes 20 to 125
(160 bar) (20 to 125 cm3/rev) Replaces: 11.91
– variable displacement

– low noise level

– hydrodynamically lubricated sleeve bearings provide long life

– bronze-coated control plates provide favorable frictional

characteristics
– single compensator fits all displacements and controllers
(C, D W and E)

– optional control of pressure and flow, upon request

K4752-7
– low hysteresis
– short control times
Type V4/20
– air bleed standard
– test point
– can also be supplied as combination pump

P r o g ress
Out i n
Phase ext 6 Pages
F90003

See N 1 0 515 Type V4 with lockable compensator

see R A
Please Vane Pump
PV7…

testpoint
F90005

Type V4/Testpoint
K4751-7

Type V4 + V4-Combination

1
RA 10 460/03.95

Ordering code
Streamlining the Model Code Types of the 1PV2V4 variable Vane Pump
After consuming the parts in stock, the outlined versions are no longer available.
For replacements, please review corresponding footnotes.

1 PV 2 V4 R 5*

Series further details

Series 20 to 29 = 2X in clear text
Size 20 and Size 50
(20 to 29, externally automatic bleed valve
interchangeable) 1= 6) without valve
Series 30 to 39 = 3X Displacement control
Size 32 and Size 80 N= without setting screw
(30 to 39, externally A= 7) with setting screw
interchangeable)
Series 40 to 49 = 4X Stall pressure range
Size 125 16 = up to 2320 PSI (160 bar)
(40 to 49, externally optimum range
interchangeable) 580 to 2320 PSI (40 to 160 bar)
Other stall pressure settings
Size / Displacement
Details in clear text
Veff
Size 20 20.7 cm3 = 20 Control settings
Size 32 34.5 cm3 = 32 1= 8) setting screw
Size 50 55.2 cm3 = 50 3= lockable rotaryhand knob with scale
Size 80 82.8 cm3 = 80 5= 9) setting screw and K-plate
Size 125 127.6 cm3 = 125 for minimum start pressure
7 = lockable rotary hand knob with
Direction of rotation scale and K-plate
Clockwise =R
(viewed on shaft end) Controls*
C = pressure control-mechanic adjustable
Shaft end D = pressure control-remote hydraulic adjustable
front shaft keyed metric =A E = 10) pressure control-remote electric adjustable
front shaft end keyed metric - rear shaft end splined =E W = pressure control 2 stage electric switchable
front shaft splined - rear shaft end splined =F N= flow control-mechanical flow setting
front shaft splined =G
front shaft keyed SAE =W
Connections Seals
M= NBR-seals, suitable for use with mineral oils (HLP) to
Standard model
DIN 51524 part 3 mineral oils (HLP)
Size 20, 32, 50: suction and pressure ports: SAE threaded = 12
V = 12) FPM-seals, suitable for use with phosphate-ester
Size 80: suction port: SAE flange = 16
(HFD-R)
pressure port: SAE thread;
K= NBR-seals and FPM shaft seal
Size 125: suction and pressure ports: SAE flanges = 15
Model with mounting for servo orifice on pressure port
Size 20, 32, 50: suction port: BSP thread 4) = 27
Size 80: suction port: SAE flange 5) = 36
Size 125: suction port: SAE flange 5A) = 07

Footnotes: Streamlined 1PV2V4... Vane Pump

1
The single end shaft type “A”, metric, will be substituted with thru-drive shaft, metric, “E”
2
The middle/rear pump shaft type “G” will be substituted with thru-drive shaft, spline, “F”
3
The American keyed shaft “W” will be standard with thru-drive splined rear, (see illustration 1). If envelope dimensions do not
permit this solution. Please contact us for specific applications.
4, 5, 5a
The “Servo blend” orifice mounts are not available; however for replacement requirements, please contact us for specific
solutions i.e.: mill pressure port pad, or provide an adapter from pressure port to “Servo Blend” control.
6
The airbleed designation “1” will remain in the model code; however no airbleed will be provided.
7
The displacement control “A”, with set screw is only option. Special versions, i.e.: Dr. Boy can still be provided.
3, 9
Standard compensator with set screw adjustment “K” plate with set screw adjustment only.
10, 11
Controls “E” and “W” are not specifically available; however can be duplicated by removing access plate from new “D”
control, part #543378.
12
“V” seals not available, “K” (FPM shaft seal), only for temperature, not for HFD fluid.
* Controllers type: “J’, “T”, “R”, “V”, “U”, and “F” are no longer available. For replacement requirements, please contact us for
specific solutions. The specials, “A93”, and “A86” will remain available in the near future.

2
 RA 10 460/03.95

Current version, V4
Example: V4/20

Future supply, V4
Example: V4/20
• No airbleed
• Shaft with Thru-Drive Standard
(~1" overall length increase)

3
RA 10 460/03.95

Technical data (for operation outside these parameters, please consult us!)

General
Construction Variable vane pump
Type V4
Mounting Flange mounting
Connections Threaded or flanged, dependent on size of unit and model designation
Installation position Optional, preferrably horizontal (see page 8)
Shaft loading Radial and axial forces cannot be accepted
Direction of rotation Clockwise (viewed on shaft end)
Speed range n min bis n max rpm 900 to 1800
Size 20 32 50 80 125
Drive power (n = 1750 rpm) Peff HP 13.8 23.5 37.34 51.8 71.7
(kW) (10.3) (17.5) (27.8) (38.6) (64)
Torque T max lb-ft 166.69 216.84 376.16 376.16 723.52
(Nm) (228) (294) (510) (510) (1330)
Weight (with pressure control C1) m lbs. 51.79 68.32 94.33 123.42 211.58
(kg) (23.5) (31) (42.8) (56) (98)
Hydraulic
Size 20 32 50 80 125
Displacement Veff in3 1.26 2.11 3.37 5.05 7.79
(cm3) (20.7) (34.5) (55.2) (82.8) (127.6)
Max. flow Q GPM 9.25 16.9 24.3 38 57.7
at n = 1750 min-1; p = 145 PSI (10 bar) (L/min) (35) (64) (92) (144) (218)

Nominal pressure pN PSI (bar) 2320 PSI (160 bar)

Operating pressure (absolute)
Inlet p PSIA (bar) 12 PSIA to 36 PSIA (0.8 to 2.5 bar)
Outlet p PSI (bar) 2320 PSI (up to 160 bar)
optimum adjustable
Compensator pressure range pNH PSI (bar) 580 to 2320 PSI (40 to 160)1
Leakage outlet, max p PSI (bar) 29 (2)
Fluid HLP-mineral oils petroleum; phosphate-ester (HFD-R
Please observe the specifications in data sheet RA 07 075!
Fluid temperature range °F (°C) 14 to 158 °F (–10 to +70 °C) (note permissible viscosity range)
Viscosity range ν SUS (mm2/s) 75 to 740 SUS (16 to 160 mm2/s) at operating temperature and
deadhead pressure below 915 PSI (63 bar)
120 to 740 SUS (25 to 160 mm2/s) at operating temperature and
deadhead pressure above 915 PSI (63 bar)
max. 3720 SUS (800 mm2/s) when starting up when the pump
is delivering
max. 930 SUS (200 mm2/s) when starting up deadheaded
Maximum degree of fluid contamination Class 18/15 according to ISO 4406
Therrefore, we recommend a filter with a retention rate of ß20 ≥ 75.
To ensure longer pump life, we recommend class 17/14 according to
ISO 4406.Therefore, we recommend a filter with a retention rate
of ß10 ≥ 100.
1
For compensator values <40 bar please consult us

4
 RA 10 460/03.95

Unit dimensions*, pump - all sizes: dimensions in inches (millimeters)

Y Note: Descriptions of number identities

are found on page 13.

B1 B2
B7
1
P
D1/T1

øD6

H2
3 øD
4
H3

H4
0.315 (8) A/F
0.945 (24) A/F
H1

S D2/T2
2
B3
X

øD11

10
D8/T8 13
0.67 (17) A/F
L12 8 L14
B6 5
0.118 (3) A/F
4
11

D9/T9

L13
max.
(L2)
L11 L3
a) L8
b) L15
L1
L4

9 L10
D3/T3
L6
B4 L5 L7 L9
7
6
øD5
12
B5

øD7

1 A
* shown pump: 1 PV 2 V4-3X/80 RW 16 ... C 3 –16 N 1
A/F = Across Flats

5
RA 10 460/03.95

Unit dimensions, pump - all sizes: dimensions in inches (millimeters)

View X S1 1 Pressure port 6 Drain port
Only sizes 80, 125 2 Suction port 7 Drive shaft
3 Maximum displacement setting via (clockwise rotation)
adjustment screw 8 Acorn nut
S

S2
Type code ..A.. 9 without setting screw for
Clockwise rotation: adjusting displacement
reduces replacement 10 Gauge port (remove plug)
Counter-clockwise rotation: 11 Thread for lifting lugs
D9 increases displacement Size 50: M8; 0.511 (13) deep
1/2"-13 UNC 4 Deadhead pressure setting Size 80: M8; 0.511 (13) deep
Size 80; 1.1 (27) deep via allen head adjustment screw Size 125: M10; 0.708 (18) deep
Size 125; 0.6 (16) deep 0.118 (3) A/F 12 a)
Pressure line
Ordering code see controllers b)
Suction line
View Y 2.748 Clockwise rotation: (180° opposite)
Only size 125 (69.8) increases pressure 13 Space required for removal
(SAE 1-1/2") Counter-clockwise rotation: of key
reduces pressure
(35.7)
1.406

P 5 Deadhead pressure setting

via lockable adjustment device
For mounting brackets see RA 45 525
Ordering code see controller
(key: ordering no. RR00 008158)
Ø 1-1/2" (38)
Note:
1/2"-13 UNC/0.6 (16) deep
Unit dimensions for version 1 PV 2 V4–.X/..RW..MC1 –16 N 1
3 A
A/F = Across Flats

Size B1 B2 B3 B4 B5 B6 B7 ØD1 T1 ØD2 T2 ØD3 T3 ØD4(±0.2)

5.9 5.94 4.7 0.189–0.001 3.94 5.08 3.89 SAE-8 0.551 SAE-16 0.709 SAE-6 0.47 5.000±0.008
V4-1X/20 (150) (151) (120) (4.788–0.025) (100) (129) (99) 3/4–16 (14) 1-5/16–12 (18) 9/16–18 (12) (127.0)
6.2 6.37 6.0 0.251–0.001 3.27 5.35 4.33 SAE-12 0.630 SAE-20 0.787 SAE-6 0.47 6.374±0.008
V4-2X/32
(157) (162) (152) (6.375–0.025) (83) (136) (110) 1-1/16–12 (16) 1-5/8–12 (20) 9/16–18 (12) (161.9)
V4-2X/50 6.4 6.92 5.9 0.376–0.001 3.94 5.59 4.88 SAE-16 0.709 SAE-24 0.866 SAE-8 0.47 6.374±0.008
(163) (176) (150) (9.550–0.025) (100) (142) (124) 1-5/16–12 (18) 1-7/8–12 (22) 3/4–16 (12) (161.9)
6.9 7.16 7.9 0.376–0.001 4.25 6.10 5.11 SAE-20 0.787 SAE-12 0.63 8.996±0.008
V4-3X/80 (176) (182) (200) (9.550–0.025) (108) (155) (130) 1-5/8–12 (20) SAE 2" — 1-1/16–12 (16) (228.5)
8.4 10.43 8.8 0.376–0.001 6.14 7.60 6.49 SAE SAE SAE-16 0.71 9.843±0.008
V4-3X/125 — —
(214) (265) (224) (9.550–0.025) (156) (193) (165) 1-1/2" 2-1/2" 1-5/16–12 (18) (250.0)

Size ØD5 ØD6 ØD7 ØD8 D9 T9 D10 D11 H1 H2 H3 H4 L1 L2

+0.0006
V4-1X/20 0.998+0.0001 0.56 4.000–0.002 G 1/4" 0.787 0.098 — 2.36 3.11 3.90 7.2 1.087 8.46 6.42
(25.37+0.015
+0.002) (14.4) (101.6–0.05) (20) (2.5) (60) (79) (99) (184) (27.6) (215) (163)
1.25+0.0007
+0.0001 0.56 5.000–0.002 0.905 0.492 2.36 3.66 4.25 8.1 1.362 9.33 6.65
V4-2X/32 (31.75+0.018) (14.4) (127.0–0.05) G 3/8" (23) (12.5) — (60) (93) (108) (206) (34.6) (237) (169)
+0.002
+0.0007
1.50+0.0001 0.56 5.000–0.002 0.905 0.157 2.36 3.62 4.53 8.7 1.665 11.14 8.46
V4-2X/50 G 3/8" —
(38.1+0.018
+0.002) (14.4) (127.0–0.05) (23) (4) (60) (92) (115) (220) (42.3) (283) (215)
+0.0007
1.50+0.0001 0.81 6.000–0.002 0.905 0.314 1.889 2.36 4.29 4.84 9.6 1.665 11.34 8.70
V4-3X/80 G 3/8"
(38.1+0.018
+0.002) (20.7) (152.4–0.05) (23) (8) (48) (60) (109) (123) (243) (42.3) (288) (221)
+0.0007
V4-3X/125 1.75+0.0001 0.87 7.874–0.003 G 3/8" 0.905 0.275 2.480 2.36 4.65 5.12 11.5 1.921 14.76 11.14
+0.018
(44.45+0.002 ) (22.0) (200.0–0.072) (23) (7) (63) (60) (118) (130) (291) (48.8) (375) (283)

Size L3 L4 L5 L6 L7 L8 L9 L10 L11 L12 L13 L14 L15 S1 S2

V4-1X/20 6.594 3.228 1.654 2.047 0.354 1.102 0.433 0.669 5.472 0.629 8.543 1.771 1.102 — —
(167.5) (82) (42) (52) (9) (28) (11) (17) (139) (16) (217) (45) (28)
6.751 3.385 2.283 2.696 0.393 1.259 0.472 0.826 5.905 0.590 8.661 1.771 1.259
V4-2X/32 (171.5) (86) (58) (68.5) (10) (32) (12) (21) (150) (15) (220) (45) (32) — —
7.618 4.251 2.283 2.677 0.354 1.437 0.492 0.905 7.401 0.708 9.566 1.771 1.437
V4-2X/50 — —
(193.5) (108) (58) (68) (9) (36.5) (12.5) (23) (188) (18) (243) (45) (36.5)
7.854 4.488 2.276 2.677 0.354 1.673 0.629 1.259 7.992 0.708 9.803 1.771 2.047 3.063 1.689 SAE
V4-3X/80
(199.5) (114) (57.8) (68) (9) (42.5) (16) (32) (203) (18) (249) (45) (52) (77.8) (42.9) 2"
V4-3X/125 8.720 5.669 3.228 3.641 0.354 2.244 0.984 1.535 9.409 1.181 10.66 1.771 2.244 3.500 2.004 SAE
(221.5) (144) (82) (92.5) (9) (57) (25) (39) (239) (30) (271) (45) (57) (88.9) (59.9) 2-1/2"

Mannesmann Rexroth Corporation

Rexroth Hydraulics Div., Industrial, 2315 City Line Road, Bethlehem, PA 18017-2131 Tel. (610) 694-8300 Fax: (610) 694-8467
Rexroth Hydraulics Div., Mobile, 1700 Old Mansfield Road, Wooster, OH 44691-0394 Tel. (330) 263-3400 Fax: (330) 263-3333

6 All rights reserved – Subject to revision

Printed in U.S.A.