Crush Test Methods: To Determine Ring Crush Resistance

CRUSH TEST METHODS
Ring Crush Test (RCT)

To determine ring crush resistance.
A 152.4 x 12.7 mm paper or board sample, prepared with the

strip punch (see page 207), is inserted, long edge uppermost,
into the sample holder and placed in the crush tester. Different
sample holders are available for different material thickness.
In the RCT test, the test strip is exposed to compression

until it buckles. The force measured indicates how much
force is required to finally break them.
Sample holder for the Ring Crush Test (RCT)
Concora Crush Test (CCT)

To determine the crush resistance of flutes.
A 152 x 12.7 mm sample, prepared with the concora f luter

(see page 144) is placed in the sample holder of the crush
tester with the long edge uppermost. Different sample
holders are available for different f lute sizes (see pages 146
– 147).
In the CCT test, the f lute is exposed to compression on the

long edge until it buckles. The force measured indicates
how much force is required to break the fibres.
Sample holder for the Concora Crush Test (CCT)
Edge Crush Test (ECT)

To determine the edge crush resistance of corrugated board.
A 100 x 25 mm sample, prepared with the ECT sample saw (see

pages 132 – 133) is placed long edge uppermost in the crush tester
between two metal blocks. The two blocks prevent sideways
slippage of the sample during the crush test.
In the ECT test, the corrugated board is exposed to compression

until it buckles. The force measured indicates how much force
is required to finally break them.
Sample holder for the Edge Crush Test (ECT)
140 Board Testing Instruments

Score Quality Test (SQT) acc. TAPPI T829
To determine the score quality of corrugated board.
The prepared 25.4 mm sample is rilled, in MD or CD as required,

and placed in the sample holder.
In the SQT test, a compression bar applies pressure to the

rilling line in the middle of the corrugated boards until this
is pushed downwards at least 12.7 mm, or the angle between
the two sides reaches 90°. The force required is compared
with force used in a test with uncorrugated board. This
procedure allows the score quality to be determined.
Sample holder for the Score Quality Test (SQT)
Pin Adhesion Test (PAT)

To determine the adhesion bond strength of corrugated board.
The pins of the holder for the PAT test are inserted through
the flutes of the corrugated board in such a way that the lower
holder presses the flute upwards and the upper holder pushes
the lower linerboard downwards. Sample holders are available
for different flute sizes (see pages 146 – 147).
In the PAT test, force is applied to the inner side of the

linerboard until the bond is broken between the board and
the adhesive. The measured values indicate how much force
must be applied to break the bond between linerboard and
f lutes.
Sample holder for the Pin Adhesion Test (PAT)
Concora Medium Test (CMT)

To determine the crush resistance of concora flutes.
The 152 x 12.7 mm sample prepared with the concora fluter

(see pages 144 – 145) is glued with the aid of the third hand and
placed between the platens of the crush tester.
In the CMT test, the flutes are exposed to compression until

they buckle. The force measured indicates up to which point
the fibres recover or when they can no longer return to their
original shape (meander point, see page 142) and how much
force is required to finally break them.
Concora Medium Test (CMT)
Board Testing Instruments 141

MEANDER POINT
The meander point is the point during compression testing
when the fibres are compressed to such an extent that they no
longer return to the start position when the load is removed.
Undamaged sample
In practice this means that:
• If, during the CMT test (see page 141), a sample is

compressed in the range below the meander point,
when the pressure platens are removed the sample
can be returned to its original condition.
• If the sample is compressed beyond the meander

Meander point: the flute can take force once more point (meaning that some fibres are damaged
without the sample collapsing), it is no longer
possible to return to the start values by removing
the pressure platens.
• Collapse of the sample occurs only when the force

applied is far in excess of the meander point.
Damaged sample
142 Board Testing Instruments

Crush Test Methods: To Determine Ring Crush Resistance

Uploaded by

Copyright:

Available Formats

Crush Test Methods: To Determine Ring Crush Resistance

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Crush Test Methods: To Determine Ring Crush Resistance

Uploaded by

Copyright:

Available Formats

CRUSH TEST METHODS

Ring Crush Test (RCT)

A 152.4 x 12.7 mm paper or board sample, prepared with the

In the RCT test, the test strip is exposed to compression

Sample holder for the Ring Crush Test (RCT)

Concora Crush Test (CCT)

A 152 x 12.7 mm sample, prepared with the concora f luter

In the CCT test, the f lute is exposed to compression on the

Sample holder for the Concora Crush Test (CCT)

Edge Crush Test (ECT)

A 100 x 25 mm sample, prepared with the ECT sample saw (see

In the ECT test, the corrugated board is exposed to compression

Sample holder for the Edge Crush Test (ECT)

140 Board Testing Instruments

The prepared 25.4 mm sample is rilled, in MD or CD as required,

In the SQT test, a compression bar applies pressure to the

Sample holder for the Score Quality Test (SQT)

Pin Adhesion Test (PAT)

In the PAT test, force is applied to the inner side of the

Concora Medium Test (CMT)

The 152 x 12.7 mm sample prepared with the concora fluter

In the CMT test, the flutes are exposed to compression until

Concora Medium Test (CMT)

Board Testing Instruments 141

• If, during the CMT test (see page 141), a sample is

• If the sample is compressed beyond the meander

• Collapse of the sample occurs only when the force

142 Board Testing Instruments

You might also like