Scribd
Upload
445 views1 page

At12 303

This document provides specifications for the Band II 2 crossed dipoles circular/elliptical polarization panel antenna. The antenna is suitable for triangular masts and operates in the 87.5-108 MHz frequency range with a peak gain of 4.5 dB and 3 dB beam width of 92 degrees horizontally and vertically. It can handle maximum powers between 5-14 kW depending on the connector type and has dimensions of 2000 x 1013 x 2000 mm. Systems with multiple antennas can be arranged with heights ranging from 2000-21600 mm and gains between 2.6-11.6 dBd depending on the number of bays.

Uploaded by

Marcos Duván Pineda Alhucema
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
445 views1 page

At12 303

This document provides specifications for the Band II 2 crossed dipoles circular/elliptical polarization panel antenna. The antenna is suitable for triangular masts and operates in the 87.5-108 MHz frequency range with a peak gain of 4.5 dB and 3 dB beam width of 92 degrees horizontally and vertically. It can handle maximum powers between 5-14 kW depending on the connector type and has dimensions of 2000 x 1013 x 2000 mm. Systems with multiple antennas can be arranged with heights ranging from 2000-21600 mm and gains between 2.6-11.6 dBd depending on the number of bays.

Uploaded by

Marcos Duván Pineda Alhucema
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

AT12-303

Band II 2 crossed dipoles circular/elliptical polarization panel ● Especially suitable for triangular masts

Electrical Specifications
Frequency range 87.5-108 MHz
Peak gain 4.5 dB (ref. /2 dipole)
3 dB beam width Horizontal: 92º Vertical: 92º
Polarization Circular / Elliptical
Impedance 50 Ohm
VSWR  1.1:1 (with circular polarization)
Maximum power handling 5 kW 10 kW 14 kW
(per connector) (2.5 kW) (5 kW) (7 kW)
2x 2x 2x
Connector type (2 per antenna)
DIN 7/16 EIA 7/8” DIN 13/30
Non Gas barrier on input
Pressurization pressurized connector
Fully pressurized as an option

Mechanical & Environmental Specifications


Materials Hot dip galvanized steel
Dimensions (W x D x H) 2000 x 1013 x 2000 mm
Maximum wind speed 200 km/h
Wind load (front) 1150 N (@160 km/h)
Wind load (lateral) 803 N (@160 km/h)
Weight 55 kg
Typical mounting Triangular arrangement tower
Clamp type To Ø 80 – 115 mm pipe
Vertical spacing 2800 mm typical
Grounding DC grounded
Temperature range -40°C to +80°C
Humidity 100%

Antenna System Characteristics


Wind load System
Number Number ant. Peak gain Weight
(@160 height
of Bays per bay (dBd) (kg)
km/h) (mm)
2 2.6 110 2.5 kN
1 2000
3 0.4 165 3.7 kN
2 5.6 220 5.1 kN
2 4800
3 3.4 330 7.4 kN NOTES:
2 8.6 440 10.1 kN
4 10400 - Table supplies data up to 8 bays only
3 6.4 660 14.8 kN for simplification purposes; systems with
2 10.4 660 15.2 kN more bays are available.
6 16000 - Null fill, beam tilt, harness & feeder
3 8.2 990 22.1 kN
2 11.6 880 20.3 kN losses NOT INCLUDED.
8 21600 - Wind load & weight figures without
3 9.4 1320 29.5 kN considering cables, splitters & hardware.

The above specified gain must be understood for circular polarization

E-mail: [email protected]
RYMSA RF will reserve the right to make any changes without notice. Web: www.rymsarf.com

You might also like