Segmental Construction of Bridge

SEMINAR
ON
SEGMENTAL CONSTRUCTION
OF BRIDGE
SUBMITTED BY:-
NITESH BHARDWAJ
ROLL NO.-15217007
Contents:
 Introduction of Bridge
 Components of a Bridge
 Construction methods for bridges
 Introduction of Segmental bridge construction
 Classification of segmental bridges
 Construction of segmental bridges
A Case Study of Sutong Bridge china
 Some other examples of segmental bridges
 Conclusion.
 References
BRIDGE
A bridge is a structure built across an obstacles
such as a body of water, valley, or road, for the
purpose of providing passage over the obstacle.
Designs of bridges depend on the function of the
bridge, length of the bridge, span of the bridge,
the nature of the terrain, and the material used to
make it.
Components of a bridge
 Superstructure or Bridge deck – the horizontal
part of a bridge that support pedestrian or traffic
activities.
 Bearings - transmit the load received from the
decking on to the substructure.
 Substructure –
 Piers or Abutments- Vertical member support the deck
or bearing.
 Foundation – Transmits the load of Superstructure,
Piers or Abutments evenly distribute the load on to
the strata
Construction Methods for Bridge
1. Cast-in-Situ Method :
This Method Prefer for Short Bridges. Time
consuming is large in cast-in-situ
construction as it involves following steps.
 Erection on ground supported staging

 Casting of concrete
 Dismantling of staging
2. Precast Segmental Method:
This method is
used for the

SEGMENTAL BRIDGE
CONSTRUCION
A Segmental Bridge is a bridge built in
short sections (called segments), that is one
piece at a time. And then segments are
erected to make the bridge. The bridge is
either cast-in-place or precast.
Advantage of segmental bridge

construction
Contd.
 The structure can be fully loaded immediately after
being prestressed.
 The pre-stressed cables can be inspected and
replaced at all times.
 Low weight due to thin bridge sections.
 Industrialization of the construction process.
 Innovations in construction equipment.
 Low maintenance costs.
 Speed of construction, time taken less
Disadvantage of Segmental bridge
construction
 High construction loading or high technology is
used.
 Need high safety precautions during construction
 Extra cost (due to more prestressing required)
History of Segmental bridge construction

Segmental bridge construction first appeared in the
early 1950s.
 The first cast-in-place segmental concrete bridge,
built in 1950, across the Lahn River in Germany.
 The first precast segmental concrete bridge, built in
1962, across the Seine River in France.
Classification of segmental bridges
Segmental bridges is classified under the following
Categories.
 Balance Cantilever Bridges

 Progressive Placement Bridges
 Span-by-Span Constructed Bridges
 Incrementally Launched Bridges
Segmental Construction Method
Balanced Cantilever
Progressive placement
Span-by-span
Incrementally launched
Construction of Segmental Bridges
The following steps are used for the
construction of
Segmental bridges.
1. Casting of Segments
Two method used for casting of segments
 Short Line Method
In this rate of segment production is
slow. Three or four segments cast at a
time.
Contd.
After casting the segments are stored at staking yard
and curing of segments will be done.
2. Transfer the segment at erection site:

After casting or curing of segments are transferred
at erection site with the help of traveler or crane.
Casting of Segments
Casting of Segments
Storage of Segments
Typical Features of Precast Segments
Lifting of Segments
Lifting of Segments
Contd.
3. Erection of the segments:
The precast segments are erected on the sites by
following erection methods.
 Balanced Cantilever erection
 Progressive Placement erection
 Span by Span erection
 Incremental Launching erection
Contd.
High Machineries are used for the erection of
segments some of the following.
 Launching Truss & accessories
 Launching girder & accessories
 Gantry crane or other cranes
 Hydraulic jacks
 Travelers
Erection of Segments
Progressive placement erection
Incremental launching erection
Contd.
4. Epoxy Glueing
In between the two segments epoxy Glueing is
used to prevent the leakage of grout during
grouting.
5. External perstressing
Used for giving the final strength to bridge.
 Pre-tension method
 post tension method
Contd.
6. Grouting
The main purpose of grouting is to protect the
all strands against corrosion and develop the
bond between prestressing steel and
surrounding concrete.
Segmental bridges-A Case Study of
Sutong Bridge china
1. Project
Description
1.1 Location across
the Yangtze
River
China
Sutong Bridge china
1.2 Sutong Bridge is the first precast segmental
bridge built using short-line match-casting
method in China.
1.3 It was constructed using balanced cantilever
method. Prestressed concrete continuous
single-cell box girder structure was constructed
precast segmental method. The construction of
the precast segmental approach structures
commenced in April 2004 and completed in
early 2007.
Sutong Bridge china
1.4 It consist of 30m, 50m or 75m long span. The
total length of the box girder measured along
its centerline was approximate 3.7km.
1.5 The reinforced concrete columns with 4.5m x
6.5m rectangular hollow section were adopted
for the maximum height of 60m and supported
on pile caps with bored pile foundation.
Sutong Bridge china
2. Segment Casting:
Segment were casted in casting yard The
casting yard was about 40,000m2 and equipped
with 2 numbers of 160 ton gantry cranes for
segment handling and 2 numbers of 16 ton
gantry cranes for light duty tasks, such as,
manipulating the reinforcement cage. The
casting yard had a storage capacity of 354
segments based on two-layer stacking.
Sutong Bridge china
Casting yard Layout Plan
Sutong Bridge china
3. Segment Erection:
The total erection period was about 15 months.
Two overhead launching girders were used.
Each girder had two winches with lifting
capacities of 180 ton and 150 ton respectively.
The lifting height of the winches was allowed
for 70m.
Sutong Bridge china
Partially Erected Bridges Launching girder assembling
Other Examples of Segmental bridges
Conclusions:
 This method is ideal for bridge construction
bridge give Aesthetical view or good quality.
 Longer span bridge now possible.
 Longer bridge over water now possible.
 Construction of long bridges now easy.
 Construction time is less.
 Environment friendly construction.
 Construction line is highly mechanized by this
method.
References:
 Segmental Concrete Bridge Construction - NBM
Media www.nbmcw.com
 Bridge construction method www.ttfijnmechanica.nl
 Segmental bridge technology Rohleder_presentation
mceer.buffalo.edu/education/bridge.../
 Seminar on Segmental Construction
www.faeto.org/pdf/segmental_bridge_construction.pdf
 Construction of the Precast Segmental Approach
Structures for Sutong Bridge a paper by Xian Peng LIU,
Zong Ping QIN, Y.W. LEUNG, YWL and Dr. Lingling
YUE, www.ywlgroup.com/a02.pdf
YOUR
ATTENTION

Segmental Construction of Bridge

Uploaded by

Copyright:

Available Formats

Segmental Construction of Bridge

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Segmental Construction of Bridge

Uploaded by

Copyright:

Available Formats

What are the different types of bridges discussed?

What are the advantages of segmental bridge construction?

SEMINAR

 Erection on ground supported staging

used for the

Advantage of segmental bridge

History of Segmental bridge construction

 Balance Cantilever Bridges

2. Transfer the segment at erection site:

You might also like