INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 3, ISSUE 4, APRIL 2014 ISSN 2277-8616

Modeling And Analysis Of Rocket Outer Shell

Sheikh Naunehal Ahamed, Jadav Vijay Kumar, Mohammed Mushraffuddin, Parimi Shrawini

Abstract: The research aims at modeling a rocket case to accomplish mission requirements. The various reasons that may cause case failures are
improper design and analysis, lack of non-destructive tests during critical phases of fabrication, negligence in service conditions, improper material
selection. Hence it‟s very essential to model rocket with perfect designing and analysis. This journal entails the designing of rocket case using Catia V5,
meshing with Hypermesh and Analysis with Ansys, where different materials like Aluminium and Epoxy-carbon are selected. The results focus on the
deformation produced under same loading condition in two different materials and studying the results.

Index Terms: Multistaging, Finite Element Method, Catia, Hypermesh, Ansys, Epoxy-carbon
————————————————————

1 INTRODUCTION mph and lift it to 1000 miles altitude. At that point the third
The important aspects the case design must satisfy are stage takes over to complete earth orbital injection (17,500
presented and the detail procedure for designing the rocket mph), and later to accelerate the rocket to the 25,000 mph
shell using CATIA v5 tools is also presented. The model is velocity necessarily to escape the pull of earth‟s gravity.
then imported into hyper mesh software in order to mesh the Staging in the rocket means combination of stages. In other
model properly and then exported into the ANSYS software to words, it‟s the stacking of rockets. The first stage is the
conduct the analysis. The analysis on the rocket shell model launching rocket or the booster. The booster is shed when it
designed and meshed is conducted using ANSYS10.0 tools has consumed all fuel. It takes place within two minutes. After
representing that the model designed when an advanced this, engine of the second stage starts. When it uses up all its
material such as Carbon-EPOXY is considered in spite of fuel, it too is released and the third engine fires up and so on.
aluminium is suitable for mission requirements and proved to
be effective. 1.4 Why Multistaging?
Why do rocket designers complicate their task with several
1.1 Rocket Structural System engine sizes, many separate fuel tanks and complicated
The structural system of a rocket includes all of the parts separation mechanisms, instead of designing one huge rocket,
which make up the frame of the rocket; the cylindrical body, containing all the fuel that will be doing the whole job at once?
the fairings, and any control fins. The function of the structural There are two fundamental reasons for staging:
system is to transmit the loads from the forces generated 1. To improve the performance by eliminating dead
during the flight and to provide low aerodynamic drag for flight weight during powered flight
through the atmosphere. Rocket structures must be strong but 2. To maintain acceleration within the reasonable limits
light weight. The performance of the rocket depends directly by reducing thrust in mid-flight.
on the weight of the structure. A variety of mass ratios are
used to characterize the structural weight of a rocket. The
distribution of the structural weight also affects the center of
gravity of the rocket which, in turn, affects
the stability and control of the rocket. During the flight of a
rocket to orbit, some parts of the structure are discarded in a
process called staging.

1.2 Basic Structural Design Requirements

1. Rocket structures must be strong but light weight. The
performance of the rocket depends directly on the
weight of the structure.
2 The casing must be able to sustain the mechanical
loads acting on the structure.
3 It should able to sustain the weight of the engine,
propellant, and the payload.
4 The body is profiled to avoid drag that is encountered
when travelling at super- and hypersonic speeds in
the atmosphere.

1.3 Rocket Staging

Most modern, high performance rockets, particularly those
used in space applications, are multistage rockets. The Saturn Fig 1: Altitudes attained by various methods using two
V moon rocket is a perfect example of a multi stage vehicle; engines.
this rocket uses three distinct stages in order to send its
payload of astronauts and equipment towards the moon. The
Saturn 1C first stage lifts the rocket to 200,00feet with 7-1/2
million pounds thrust. The first stage then separates and the
S-II second stage ignites to accelerate the rocket to 15,300
270
IJSTR©2014
www.ijstr.org
INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 3, ISSUE 4, APRIL 2014 ISSN 2277-8616

2 DESIGNS
2.1 Design Consideration
The outer shell configuration is selected as the optimum or
best envelope to maximize performance and minimize cost.
The final shell configuration can be determined on the basis of
payload, inter-stage connecting structures, handling
equipments, launch facilities, use of specified propellant
configuration or auxiliary equipment. Some commonly used
configurations are below:

Fig 2: Some commonly used rocket shell configurations.

Here we considered a multi-staged rocket with multi-sectioned

cylindrical casing which is considered from a previous rocket
model i.e., Saturn V. The dimensions for the design and other
requirements are taken based on the specifications of Saturn
V shown in the figure below

Fig 3: Saturn V launch vehicle specifications & dimensions.

2.2 Rocket Outer Shell Design

Open CATIA v5 software

Start> programs> CATIA> CATIA v5r20

STEP 1: start> mechanical design> wireframe and surface

271
IJSTR©2014
www.ijstr.org
INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 3, ISSUE 4, APRIL 2014 ISSN 2277-8616

design> select an axis> insert> sketcher STEP 2: Start> mechanical design> wireframe and surface
design

Fig 4: sketcher. Fig 6: wireframe and surface design.

Draw the 2D profile of the rocket outer shell using the sketcher STEP 3: insert> surfaces> revolve> select the profile> select
tools like line/profile. the revolution axis> angular limits-angle1 360deg, angle2
0deg> ok
>constrain the geometry to the dimensions considered.

>if there is any over constrains or geometrical problems.

Follow the below steps to rectify them.

Tools> sketch analysis> diagnostic/geometry.

The figure below shows the 2D profile of the rocket outer shell
using sketcher tools:

Fig 7: revolve the rocket shell profile

STEP 4: Insert > surfaces> fill> select the curve> select

support> continuity-tangent>preview> ok

Fig 5: 2D profile of rocket shell in sketcher.

272
IJSTR©2014
www.ijstr.org
INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 3, ISSUE 4, APRIL 2014 ISSN 2277-8616

Fig 10: Assign thickness to the rocket shell.

Final design of the rocket outer shell modeled in CATIA v5

following the above steps is shown in the figure below:
Fig 8: fill the surface.

STEP 5: Insert> operations> join> select the elements to join>

ok

Fig 11: Final design of rocket shell.

2.3 Interactive Drafting

STEPS INVOLVED IN INTERACTIVE DRAFTING:

1. Start> mechanical design> drafting> new document
creation> select front, top and left view> modify> ok.
2. Sheet> properties> sheet name: Saturn v> scale-
1:2> landscape> first angle standard> ok.
Fig 9: Joining of all the elements. 3. Insert> views> projection> auxiliary view> cut a
section> double click> click to locate the draft.
STEP 6: Start> mechanical design> part design> 4. Insert> dimensioning> dimensions>
length/distance/diameter dimensions> select the
Insert> surface-based features> thick surface> select the entity.
object> reverse direction> preview> ok 5. Edit> sheet background> frame and title box> drawing
title block sample 1> apply> ok.

273
IJSTR©2014
www.ijstr.org
INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 3, ISSUE 4, APRIL 2014 ISSN 2277-8616

Fig12: Draft produced for the final design of rocket shell obtained.

3 MESHING
Preferences> user profiles> select ANSYS> ok.
3.1 Hypermesh Introduction
Hypermesh, software by Altair Engineering, is used as a pre- STEP 1: file> import> file type: iges> open file> browse the
and post processor for Finite Element Analysis and CFD. file> select> import.

3.2 Advantages of using Hypermesh

Hypermesh is a high performance pre-processor and post-
processor that provides highly interactive and visual
environment to analyze the product‟s design performance.
Hypermesh is user friendly software.

1 GEOMETRIC CLEANUP: when the design model is

imported from CAD to CAE software, we get the data loses
(unwanted geometrical errors) within the geometry. We cannot
proceed further with these data loses. Hypermesh helps to
remove these errors completely by using geometric clean up
options or geometric editing features.
5 MESHING: Fine meshing is done in hypermesh
maintaining element to element connectivity.
6 QUALITY: Check and improve the quality of mesh by Fig 13: Import geometry.
using different quality of mesh & by using different quality
parameters in hypermesh. STEP 2: GEOMETRY CLEANUP-set auto to „by topo‟
(immediately the color changes to grey). If there are any
3.3 Meshing the rocket outer shell geometric data loses or errors, it will represent them with red
To import the geometry modeled in CATIA v5 software, we color.
should first save the catia file with the extension “.igs”
Geom.> auto cleanup>
Open hypermesh software: Start> programs> Altair
Hyperworks10.0>hypermesh The auto clean up panel is automatic geometry that cleans up
274
IJSTR©2014
www.ijstr.org
INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 3, ISSUE 4, APRIL 2014 ISSN 2277-8616

preparing for meshing. It includes the equivalence of "red" free

edges, fixing of small surfaces (relative to the element size),
and detection of features such as beads. It also performs
specified surface editing/disfeaturing operations like removal
of pinholes (less than specified size), removal of edge fillets,
and the addition of a layer of washer elements around holes.

STEP 3: AUTOMESH: 2D>automesh> surfs> all> element

size=1.000> mesh type: quads> mesh.

Fig 16: Increasing or decreasing the nodes to maintain same

number of nodes on both the sides.

Nodes on the either sides of the mesh of each component or

Fig 14: Auto mesh panel. division are set to be equal in number to obtain a perfect mesh
on the object.

Fig 15: Mesh generated on the design.

STEP 4: See that nodes on either side of the mesh are Fig 17: After adjusting the nodes all over the design.
maintained in same number to obtain neat mesh.

Nodes edit: increase or decrease the nodes on one end to

exactly match with the nodes on the other side. The figure
below shows the nodes adjustment or mesh edit.

Fig 18: Mesh obtained after editing.

275
IJSTR©2014
www.ijstr.org
INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 3, ISSUE 4, APRIL 2014 ISSN 2277-8616

STEP 5: checking for the connectivity. The following steps are 5. Length: 14848 0f 37416 (40%) failed. The minimum
involved length is 0.210728.
6. Jacobean: 47 of 37416 (0%) failed. The minimum
Tool> delete> geometry or press f2 Jacobean is 0.55.
7. Taper: 1 of 37416 (0%) failed. The maximum taper is
Geom.> temp nodes> all> clear all or press shift+f2 0.50.
8. Quads:
Equivalence for nodes: press f3
Minimum interior angle: 0 of 37414 (0%) failed. The minimum
Equivalence for elements: press shift+f3 interior angle is 45.58.

STEP 6: Quality parameters: tool> check elems> Maximum interior angle: 0 of 37414 (0%) failed. The maximum
interior angle is 132.89.

Trais:

Minimum interior angle: 0 of 2 (0%) failed. The minimum

interior angle is 47.26.

Maximum interior angle: 0 of 2 (0%) failed. The maximum

interior angle is 82.71.

From the above information obtain, there 7 parameters which

are satisfying the mesh. Hence the mesh generated may be
said to a perfect mesh and it can be exported to solver
software like ANSYS, NASTRAN etc.
Fig 19: Quality parameters panel.

The quality parameters for the mesh obtained are as follows: 4 MATERIAL SELECTIONS
1. Warpage: 0 of 37416 (0%) failed. The maximum
warpage is 0.0363. 4.1 Flight structure materials
2. Aspect ratio: 0 of 37416 (0%) failed. The maximum Some of the materials commonly used in flight structures are
aspect ratio is 2.21. aluminium, steel, titanium, high-temperature nickel alloys,
3. Skew angle: 0 of 37416 (0%) failed. The maximum composites etc. In this paper we are considering the aluminum
skew angle is 44.42. and the composite material carbon epoxy for the comparison.
4. Chord deviation: 0 of 37416 (0%) failed. The
maximum deviation is 0.03.

Table 1:Atomic properties of aluminium.

Atomic number 13
Atomic radius-
0.143
goldschmidtv (nm)
Atomic weight (amu) 26.9815
Crystal structure Face centred cubic

Electric structure Ne 3s2 3p1

No e
1 5
2 1
Ionization potential 3 2
4 1
5 1
6 1

276
IJSTR©2014
www.ijstr.org
INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 3, ISSUE 4, APRIL 2014 ISSN 2277-8616

Table 2: Mechanical properties of aluminium.

Material condition Soft hard polycrystalline

Youngs modulus (GPa) 75.2

Hardness-vickers 21 35-48

Poison‟s ratio 0.345

Tensile modulus (GPa) 70.6

Tensile strength (MPa) 50-90 130-195

Yield strength (MPa) 10-35 110-170

Table 3: Physical properties of aluminium. energy of UV photons is high enough to dissociate the bonds
in polymers and subsequent absorption of moisture becomes
easy through the cracks. This leads to thermo-physical,
Boiling point ( C) 2467 mechanical and chemical changes and deterioration of
material properties. Moisture absorption on the other hand
depends on a variety of factors such as temperature, strength
Density@20 C (g cm-2) 2.70 of the interfacial bonds between the fibers and the matrix, and
flaws such as voids and fiber orientation during processing.
Hence, the objective is to study the effect of nanoclay on the
mechanical and thermal properties of carbon/epoxy nano
Melting point ( C) 660.4 composites subjected to UV radiation and condensation.

The Epoxy-carbon composite properties table is shown below:

4.2 Carbon Epoxy Table 4: properties of carbon Epoxy.
Carbon fibre reinforced polymer composite (CFRC) are widely Property Value
used as engineering materials due to: High precision
 High stiffness to weight ratio Material
tubes
 Versatile advanced material systems
Thermal expansion
 Cost effective, light weight
coefficient 0.1 x 10-6 k-1
 Ease of fabrication of complex shapes and forms
(longitudinal)
 Enhanced material properties
Volume fraction of
Major concerns 55-60 %
fibres
 Polymeric composites are viscoelastic in nature
Young‟s modulus
 Exposure to harsh environmental conditions 110-120 GPa
longitudinal
 Presence of UV radiation in polymeric composites
could lead to changes in chemical structures which
ultimately deteriorates their properties

Mechanical and Thermal Properties of Carbon/Epoxy

Nanoclay Composites Exposed to Synergistic Effect
UV Radiation and Condensation
The use of Fiber Reinforced Polymer Composites (FRPC) has
gained a lot of traction due to the high stiffness, corrosion
resistance, light weight and high fatigue performance they
offer compared to some metals, and metal alloys. However,
polymeric materials responses to harsh environmental
conditions have been one of the major concerns during its
usage in engineering applications, because of their
viscoelastic nature. Addition of small amounts of nanoclay has
shown to improve most of the properties of these polymeric
composites. These polymeric composites once exposed to UV
radiation absorb the UV rays which in turn initiate photo-
oxidation reaction in the matrix leading to formation of radical Fig 19: structure of composites and stress-strain curve for the
chemical groups. Degradation mechanisms have shown that composite material
277
IJSTR©2014
www.ijstr.org
INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 3, ISSUE 4, APRIL 2014 ISSN 2277-8616

5 PROJECT ANALYSES
5.1 Introduction to ANSYS
ANSYS is software based on Finite Element Method to solve
different mechanical problems. It helps us analyze the
structure in different conditions using finite element method to
solve complex equations.

THE FEM PROCESS

The finite element process is generally divided into three
distinct phases
1. PREPROCESSING - Build the FEM model.
2. SOLVING - Solve the equations.
3. POSTPROCESSING - Display and evaluate the
results.

5.2 Steps to conduct static analysis

STEP 1: Start> all programs> ANSYS 10.0> ANSYS.
STEP 2: save the design project file with the extension as
“.igs”.
File> import>iges… > ok> browse for the file> ok
STEP 3: preferences> structural> h-method> ok
STEP 4: pre-processor> element type> add/edit/delete>
add…> shell 99, linear layer 99> ok> close
STEP 5: real constants> add/edit/delete> add> ok> real
constant set no. 1> ok> number of layers= 1> MAT=1, Fig 20: Deformation in the rocket outer shell when aluminium
THETA=0, TK=1> ok > close is considered (1).
STEP 6: Material props> material models> structural> linear>
elastic> isotropic>enter EX and PRXY value> ok
STEP 7: meshing>mesh tool> global set number of element
divisions=20> mesh> pick all> ok
STEP 8: loads> define loads> apply> structural>
displacement> on lines> select the free edges of the shell
(lines)> apply> all DOF> ok
STEP 9: loads> define loads> apply> structural>
force/moments> on nodes> use box to select all the nodes at
the stages> apply> FZ> constant value> -10000> ok
STEP 10: solution> solve. Wait for the software intimation,
software is trying to solve the problem till the solution is done
window appears on the screen> ok
STEP 11: General postproc> plot results>
displacement>deform+undeform> ok
Contour plot> DOF solution> z-component> ok.

5.3 Displacement and contour results

The analysis is conducted by applying the loads on each of
the stages of the rocket outer shell model comparing using two
materials as already mentioned aluminium and carbon epoxy.
The material offering lesser deformation for the applied load is
considered to be the effective one for the rocket casing to
achieve the mission effectively. The comparison is made by
applying same value of loads, boundary conditions and
constraints on the model for both the materials considered
separately. The results exhibited below are obtained when
load is applied on the first stage of the rocket outer shell model
comparing the displacement and contour results for the
aluminium and the carbon epoxy materials respectively.
Fig 21: Deformation in the rocket outer shell when carbon-
epoxy is considered (1).

278
IJSTR©2014
www.ijstr.org
INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 3, ISSUE 4, APRIL 2014 ISSN 2277-8616

Fig 22: Nodal solution for the rocket shell model when Fig 24: Deformation in the rocket outer shell when aluminium
aluminium is considered (1). is considered (2).

Fig 25: Deformation in the rocket outer shell when carbon-

Fig 23: nodal solution for the rocket shell model when carbon- epoxy is considered (2).
epoxy is considered (1).

The results exhibited below are obtained when load is applied

on the second stage of the rocket outer shell model comparing
the displacement and contour results for the aluminium and
the carbon epoxy materials respectively.

279
IJSTR©2014
www.ijstr.org
INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 3, ISSUE 4, APRIL 2014 ISSN 2277-8616

deformation occurred is less for the carbon epoxy compared to

aluminium when applied same loading. It is recommended that
further research be undertaken in developing the composite
materials (eg: Carbon Epoxy) for the rocket casing as they
consists of high strength and they are reusable.

REFERENCES
[1]. NASA space vehicle design
criteriahttp://ntrs.nasa.gov/archive

[2]. Aircraft Structures for Engineering Students by T.H.G.

Meghson

[3]. Metal in rocket constructswww.tripoli.org

[4]. The rocket structural

systemexploration.grc.nasa.gov/education

[5]. Multi-stage rockets, Valkyrie report no. 5105

[6]. Morton-thiokol‟s “rocket basics”.

[7]. Rocket casingwww.fas.org

Fig 26: Nodal solution for the rocket shell model when [8]. Structure and Properties Of Engineering Materials by
aluminium is considered (2). V. S. R. Murthy

[9]. Introduction to flight, 5th edition by Anderson

[10]. Material propertieshttp://www-

materials.eng.cam.ac.uk

[11]. Spacecraft Structures by J. Jaap Wijker

[12]. 12.Introduction to rocket science and engineering by

Travis S. Taylor

[13]. Introduction To Ansys 10.0by R.B. Choudary

Fig 27: Nodal solution for the rocket shell model when carbon
epoxy is considered (2)

CONCLUSION
This project was undertaken to model and to conduct analysis
on the rocket outer shell while comparing with two different
materials such as aluminium and carbon epoxy to provide with
a best option for the rocket structure that it can perform
effectively in its flight. The results of this study shows that
Carbon epoxy can be able to perform better over that of
aluminium as noted from the results of analysis, the
280
IJSTR©2014
www.ijstr.org