Job No. Sheet No. Rev.

Drg. Ref.

Made by Date Checked

07-Sep-2018

Notes:
None

History
Date Time Name Note
07-Sep-2018 9:10: WILLIAM New

Input Data

General Specification
Design code EN 1992-1-1:2004 Eurocode 2
Maximum x/d 0.6000
(Ratio of neutral axis depth to effective depth)
Frames provide lateral stability No
Deep beam check ignored No
Check code prescribed load cases Yes
Check user defined load cases No
Use concrete self weight Yes
Concrete weight density 25.00kN/m³
Adjust moments at supports Yes
Code permissible redistribution 30.00%
Redistribute moments No
Bunched bar solutions allowed Yes
Comply with Arup Reinforcement Detailing Manual Yes

Spans
Sections are defined as follows:
STD R Depth, Width => Rectangular Section

Span Length Section

[m]
1 5.000 STD R 200. 600.
2 5.000 STD R 200. 600.
3 5.000 STD R 200. 600.

Supports
Supt. Label Type Lower Section Lower Lower Upper Section Upper Upper
Length Fixity Length Fixity
[m] [m]
1 A Encastre
2 B Pinned
3 C Pinned
4 D Pinned

Concrete Material Specification

Prop. Name fck Max. Agg. Size Tensile Static E Gamma Maximum
Strength c Strain
[N/mm²] [mm] [N/mm²] [N/mm²]
Beam / Slab C30/37 30.00 20.00 1.931 32840. 1.500 0.003500
Lower Columns C30/37 30.00 20.00 1.931 32840. 1.500 0.003500
Upper Columns C30/37 30.00 20.00 1.931 32840. 1.500 0.003500

Reinforcement Specification
Prop. Name fy Bond Coeff. Bond Coeff. Young's Gamma s Maximum
Tension Compr. Modulus Strain
[N/mm²] [N/mm²]
Main 500B 500.0 0.5000 0.6300 200000. 1.150 0.05000
Links 500B 500.0 0.5000 0.6300 200000. 1.150 0.05000

Loads
Load Span Class Type Pos. Load Pos. Load
1 1 2 2
[m] [kN] [m] [kN]
[kNm] [kNm]
1 1 Dead Uniform 35.00
2 2 Dead Uniform 35.00
3 3 Dead Uniform 35.00
4 1 Imposed Uniform 25.00
5 2 Imposed Uniform 25.00
6 3 Imposed Uniform 25.00

Prescribed Load Combinations

No. Name Dead Imposed User Wind Wind Notional Notional
(left) (right) (left) (right)
1 D 1.350 0.0 0.0 0.0 0.0 0.0 0.0
2 D.I 1.350 1.500 0.0 0.0 0.0 0.0 0.0

Prescribed Load Cases

No. Name Analyse Redistribute Span Span Span
1 2 3
1 1.35D+1.5I / 1.35D Yes No D.I D D.I
2 1.35D / 1.35D+1.5I Yes No D D.I D
3 (1 & 2)1.35D+1.5I Yes No D.I D.I D
/ 1.35D
4 (2 & 3)1.35D+1.5I Yes No D D.I D.I
/ 1.35D

Covers
Span Pos. Nominal Trans.
Allow.
Top Bottom Side Top Bottom
[mm] [mm] [mm] [mm] [mm]
1 Left 20.00 20.00 20.00 0.0 0.0
1 Mid 20.00 20.00 20.00 0.0 0.0
1 Right 20.00 20.00 20.00 0.0 0.0
2 Left 20.00 20.00 20.00 0.0 0.0
2 Mid 20.00 20.00 20.00 0.0 0.0
2 Right 20.00 20.00 20.00 0.0 0.0
3 Left 20.00 20.00 20.00 0.0 0.0
3 Mid 20.00 20.00 20.00 0.0 0.0
3 Right 20.00 20.00 20.00 0.0 0.0

Available Bar Sizes

Name Size
[mm]
0 8.000

Program ADC Version 8.4.0.12 Copyright © Oasys 1990–2014 Page 1

Printed 07-Sep-2018 Time 09:25
 Job No. Sheet No. Rev.

Drg. Ref.

Made by Date Checked

07-Sep-2018
Name Size
[mm]

1 10.00
2 12.00
3 16.00
4 20.00
5 25.00
6 32.00
7 40.00

Bar Limits
Minimum Maximum Minimum
Continuity
[mm] [mm] [mm]
Top 16.00 40.00 12.00
Bottom 16.00 40.00 12.00
Links 8.000 20.00

Bar Spacing and Cut-offs

Space for poker 75.00 mm
Preferred minimum distance between top bars 40.00 mm
Main bars cut-off distance from column/concrete face 50.00 mm
Column allowance: Cover to main column reinforcement 0.0 mm
Column allowance: Diameter of main column bars 0.0 mm

Bar Selection Criteria

Link shape Trapezoidal
Link arrangement All links closed
Mixing of bars at a section Do not mix
Preferred maximum allowable area provided 1.35 x area req'd
Saving in area req'd to justify more bars or mixed diameters 10.00%

Analysis Results

Analysis Moment and Shear Envelope

Span 1 :
Position Sagging Hogging Maximum
Moment Moment Shear
[m] [kNm] [kNm] [kN]
0.0 0.0 218.9 242.4
0.2273 0.0 166.1 222.2
0.6818 0.0 74.30 181.9
1.136 -12.97 0.8066 141.5
1.591 -55.89 0.0 101.1
2.045 -91.14 0.0 60.77
2.500 -109.6 0.0 20.41
2.955 -109.7 0.0 -41.50
3.409 -91.45 0.0 -81.87
3.864 -54.86 24.50 -122.2
4.318 0.0 67.84 -162.6
4.773 0.0 140.4 -203.0
5.000 0.0 188.8 -223.1

Span 2 :
Position Sagging Hogging Maximum
Moment Moment Shear
[m] [kNm] [kNm] [kN]
0.0 0.0 188.8 225.4
0.2273 0.0 139.9 205.3
0.6818 0.0 55.74 164.9
1.136 -35.88 20.78 124.5
1.591 -79.21 0.8889 84.17
2.045 -104.2 0.0 43.80
2.500 -110.8 0.0 -21.76
2.955 -99.13 4.802 -62.12
3.409 -69.07 27.30 -102.5
3.864 -20.67 60.41 -142.8
4.318 0.0 104.1 -183.2
4.773 0.0 190.5 -223.6
5.000 0.0 243.6 -243.8

Span 3 :
Position Sagging Hogging Maximum
Moment Moment Shear
[m] [kNm] [kNm] [kN]
0.0 0.0 243.6 270.7
0.2273 0.0 184.4 250.5
0.6818 0.0 80.46 210.2
1.136 -48.48 26.94 169.8
1.591 -111.6 0.0 129.4
2.045 -156.3 0.0 89.08
2.500 -182.7 0.0 48.72
2.955 -190.8 0.0 12.80
3.409 -180.5 0.0 -42.82
3.864 -151.9 0.0 -83.18
4.318 -104.9 0.0 -123.5
4.773 -39.55 0.0 -163.9
5.000 -984.2E-6 0.0 -184.1

Analysis Moment and Shear Summary

Span Moment Peak Position Moment at Shear Shear
at Left Moment of Peak Right at Left at
Support along Moment Support Support Right
Span Support
[kNm] [kNm] [m] [kNm] [kN] [kN]
1 218.9 188.8 242.4 0.0
0.0 -111.9 2.727 0.0 0.0 -223.1
2 188.8 243.6 225.4 0.0
0.0 -110.8 2.500 0.0 0.0 -243.8
3 243.6 0.0 270.7 0.0
0.0 -190.8 2.955 -984.2E-6 0.0 -184.1

Redistributed Moment and Shear Envelope

Span 1 :
Position Sagging Hogging Maximum
Moment Moment Shear
[m] [kNm] [kNm] [kN]
0.0 0.0 218.9 242.4
0.2273 0.0 166.1 222.2
0.6818 0.0 74.30 181.9
1.136 -12.97 0.8066 141.5
1.591 -55.89 0.0 101.1
2.045 -91.14 0.0 60.77
2.500 -109.6 0.0 20.41
2.955 -109.7 0.0 -41.50
3.409 -91.45 0.0 -81.87
3.864 -54.86 24.50 -122.2
4.318 0.0 67.84 -162.6
4.773 0.0 140.4 -203.0
5.000 0.0 188.8 -223.1

Span 2 :

Program ADC Version 8.4.0.12 Copyright © Oasys 1990–2014 Page 2

Printed 07-Sep-2018 Time 09:25
 Job No. Sheet No. Rev.

Drg. Ref.

Made by Date Checked

07-Sep-2018

Position Sagging Hogging Maximum

Moment Moment Shear
[m] [kNm] [kNm] [kN]
0.0 0.0 188.8 225.4
0.2273 0.0 139.9 205.3
0.6818 0.0 55.74 164.9
1.136 -35.88 20.78 124.5
1.591 -79.21 0.8889 84.17
2.045 -104.2 0.0 43.80
2.500 -110.8 0.0 -21.76
2.955 -99.13 4.802 -62.12
3.409 -69.07 27.30 -102.5
3.864 -20.67 60.41 -142.8
4.318 0.0 104.1 -183.2
4.773 0.0 190.5 -223.6
5.000 0.0 243.6 -243.8

Span 3 :
Position Sagging Hogging Maximum
Moment Moment Shear
[m] [kNm] [kNm] [kN]
0.0 0.0 243.6 270.7
0.2273 0.0 184.4 250.5
0.6818 0.0 80.46 210.2
1.136 -48.48 26.94 169.8
1.591 -111.6 0.0 129.4
2.045 -156.3 0.0 89.08
2.500 -182.7 0.0 48.72
2.955 -190.8 0.0 12.80
3.409 -180.5 0.0 -42.82
3.864 -151.9 0.0 -83.18
4.318 -104.9 0.0 -123.5
4.773 -39.55 0.0 -163.9
5.000 -984.2E-6 0.0 -184.1

Redistributed Moment and Shear Summary

Span Moment Peak Position Moment at Shear Shear Redistribution Redistribution
at Left Moment of Peak Right at Left at at Left at Right
Support along Moment Support Support Right Support Support
Span Support
[kNm] [kNm] [m] [kNm] [kN] [kN] [%] [%]
1 218.9 188.8 242.4 0.0 0.0 0.0
0.0 -111.9 2.727 0.0 0.0 -223.1
2 188.8 243.6 225.4 0.0 0.0 0.0
0.0 -110.8 2.500 0.0 0.0 -243.8
3 243.6 0.0 270.7 0.0 0.0 0.0
0.0 -190.8 2.955 -984.2E-6 0.0 -184.1

Analysis Support Reaction Envelopes

Support Reaction Lower Upper
Column Column
Moment Moment

[kN] [kNm] [kNm]

1 242.4 0.0 0.0
114.5 0.0 0.0
2 448.6 0.0 0.0
315.3 0.0 0.0
3 514.5 0.0 0.0
381.1 0.0 0.0
4 184.1 0.0 0.0
92.13 0.0 0.0

Design Results for Span 1

Moments
Left Mid Right
Design Hogging [kNm] at [m] 218.9 0.0 0.0 2.500 188.8 5.000
Elastic Hogging [kNm] 218.9 0.0 188.8
Design Sagging [kNm] at [m] 0.0 0.0 111.9 2.500 0.0 5.000
Elastic Sagging [kNm] 0.0 111.9 0.0
Capacity Hogging [kNm] 247.3 218.8 222.0
Capacity Sagging [kNm] 157.2 125.1 125.1
M/Mu(Hog) 0.8852 0.0 0.8504
M/Mu(Sag) 0.0 0.8946 0.0

Top Reinforcement
Left Mid Right
As.prov [mm²] 7540. 4825. 5630.
As.Required [mm²] 6274. 4021. 4877.
100*As.prov/bh [%] 6.283 4.021 4.691
Effective Depth d, d' [mm] 152.0 156.0 156.0
Governing Criterion Bending Curtailment Bending
Layer 1 Bar Ref., Length [m] 4B40 5B32
Extent from support CL [m] 0 2.325 2.975 0
2B40 2B32
0 0.4500 0.3750 0

Bottom Reinforcement
Left Mid Right
As.prov [mm²] 2945. 2199. 2199.
As.Required [mm²] 2864. 2100. 2100.
100*As.prov/bh [%] 2.454 1.833 1.833
Effective Depth d, d' [mm] 159.5 40.50 162.0 162.0 38.00
Governing Criterion Bending Bending Continuity
Layer 1 Bar Ref., Length [m] 6B25 7B20 (4.875) 7B20
Extent from support CL [m] 0 0.5250 0.07500 0.05000 0.5500 0
Comp. Comp.
Reinf. Reinf.

Links
Left Mid Right
Design Shears [kN] at [m] 212.0 0.3420 20.41 2.500 192.0 4.649
VEd, VRdc [N/mm²] 2.583 0.9396 0.2423 0.9396 2.279 0.9396
cot 2.500 2.500 2.500
Asv prov, reqd [mm²/m] 3016. 1426. 3016. 525.8 3016. 1258.
Governing Criterion Designed Minimum Designed
Bar Ref., Pitch [m] 6B8 0.1000
Extent [m]

Span / Effective Depth Ratio

Basic Ratio 17.87 (Exp. 7.16.b)
Factor K 1.300 (Table 7.4N)
Reference Reinforcement Ratio(o) 0.005477
Tension Reinforcement Ratio() 0.01639
Compression Reinforcement Ratio(') 0.0
Stress modifier 1.118 (Exp. 7.17)
Flange Width Modifier 1.000
Span Length Modifier 1.000
Permissible Span/Depth Ratio 19.97
Actual Span/Depth Ratio 30.86 > 19.97 **** limit exceeded ****

Program ADC Version 8.4.0.12 Copyright © Oasys 1990–2014 Page 3

Printed 07-Sep-2018 Time 09:25
 Job No. Sheet No. Rev.

Drg. Ref.

Made by Date Checked

07-Sep-2018
Left Mid Right

Design Results for Span 2

Moments
Left Mid Right
Design Hogging [kNm] at [m] 188.8 0.0 27.30 2.500 243.6 5.000
Elastic Hogging [kNm] 188.8 27.30 243.6
Design Sagging [kNm] at [m] 0.0 0.0 110.8 2.500 0.0 5.000
Elastic Sagging [kNm] 0.0 110.8 0.0
Capacity Hogging [kNm] 222.0 97.51 325.8
Capacity Sagging [kNm] 125.1 128.0 277.5
M/Mu(Hog) 0.8504 0.2800 0.7476
M/Mu(Sag) 0.0 0.8662 0.0

Top Reinforcement
Left Mid Right
As.prov [mm²] 5630. 1608. 7540.
As.Required [mm²] 4877. 1432. 7160.
100*As.prov/bh [%] 4.691 1.340 6.283
Effective Depth d, d' [mm] 156.0 164.0 152.0
Governing Criterion Bending Continuity Bending
Layer 1 Bar Ref., Length [m] 5B32 8B16 (3.450) 4B40
Extent from support CL [m] 0 0.9250 0.5250 1.025 1.425 0
2B32 2B40
0 0.3750 0.4500 0

Bottom Reinforcement
Left Mid Right
As.prov [mm²] 2199. 2199. 5630.
As.Required [mm²] 2100. 2066. 4944.
100*As.prov/bh [%] 1.833 1.833 4.691
Effective Depth d, d' [mm] 162.0 38.00 162.0 156.0 44.00
Governing Criterion Compatibility Bending Compatibility
Layer 1 Bar Ref., Length [m] 7B20 7B20 (4.875) 7B32
Extent from support CL [m] 0 0.5000 0.05000 0.07500 0.5500 0
Comp. Comp.
Reinf. Reinf.

Links
Left Mid Right
Design Shears [kN] at [m] 194.3 0.3510 21.76 2.500 213.4 4.658
VEd, VRdc [N/mm²] 2.306 0.9396 0.2487 0.9396 2.600 0.9396
cot 2.500 2.500 2.500
Asv prov, reqd [mm²/m] 3016. 1273. 3016. 525.8 3016. 1435.
Governing Criterion Designed Minimum Designed
Bar Ref., Pitch [m] 6B8 0.1000
Extent [m]

Span / Effective Depth Ratio

Basic Ratio 20.75 (Exp. 7.16.b)
Factor K 1.500 (Table 7.4N)
Reference Reinforcement Ratio(o) 0.005477
Tension Reinforcement Ratio() 0.01587
Compression Reinforcement Ratio(') 0.0
Stress modifier 1.155 (Exp. 7.17)
Flange Width Modifier 1.000
Span Length Modifier 1.000
Permissible Span/Depth Ratio 23.96
Actual Span/Depth Ratio 30.86 > 23.96 **** limit exceeded ****

Design Results for Span 3

Moments
Left Mid Right
Design Hogging [kNm] at [m] 243.6 0.0 0.0 2.500 0.0 4.773
Elastic Hogging [kNm] 243.6 0.0 0.0
Design Sagging [kNm] at [m] 0.0 0.0 190.8 2.500 39.55 4.773
Elastic Sagging [kNm] 0.0 190.8 39.55
Capacity Hogging [kNm] 325.8 108.9 97.89
Capacity Sagging [kNm] 277.5 208.0 86.84
M/Mu(Hog) 0.7476 0.0 0.0
M/Mu(Sag) 0.0 0.9174 0.4554

Top Reinforcement
Left Mid Right
As.prov [mm²] 7540. 1885. 1608.
As.Required [mm²] 7160. 1806. 1432.
100*As.prov/bh [%] 6.283 1.571 1.340
Effective Depth d, d' [mm] 152.0 162.0 38.00 164.0
Governing Criterion Bending Bending Continuity
Layer 1 Bar Ref., Length [m] 4B40 6B20 (3.050) 5B16
Extent from support CL [m] 0 2.275 1.900 0.05000 0.3250 0
2B40 3B16
0 0.4750 0.3250 0
Comp.
Reinf.

Bottom Reinforcement
Left Mid Right
As.prov [mm²] 5630. 5630. 1407.
As.Required [mm²] 4944. 4944. 1236.
100*As.prov/bh [%] 4.691 4.691 1.173
Effective Depth d, d' [mm] 156.0 44.00 156.0 164.0
Governing Criterion Continuity Bending Continuity
Layer 1 Bar Ref., Length [m] 7B32 7B32 (4.900) 7B16
Extent from support CL [m] 0 0.5500 0.05000 0.05000 0.5750 0
Comp.
Reinf.

Links
Left Mid Right
Design Shears [kN] at [m] 240.3 0.3420 48.72 2.500 151.3 4.631
VEd, VRdc [N/mm²] 2.928 0.9396 0.5783 0.9396 1.709 0.8785
cot 2.500 2.500 2.500
Asv prov, reqd [mm²/m] 3016. 1616. 3016. 525.8 3016. 943.2
Governing Criterion Designed Minimum Designed
Bar Ref., Pitch [m] 6B8 0.1000
Extent [m]

Span / Effective Depth Ratio

Basic Ratio 17.45 (Exp. 7.16.b)
Factor K 1.300 (Table 7.4N)
Reference Reinforcement Ratio(o) 0.005477

Program ADC Version 8.4.0.12 Copyright © Oasys 1990–2014 Page 4

Printed 07-Sep-2018 Time 09:25
 Job No. Sheet No. Rev.

Drg. Ref.

Made by Date Checked

07-Sep-2018
Left Mid Right

Tension Reinforcement Ratio() 0.04304

Compression Reinforcement Ratio(') 0.01571
Stress modifier 1.090 (Exp. 7.17)
Flange Width Modifier 1.000
Span Length Modifier 1.000
Permissible Span/Depth Ratio 19.02
Actual Span/Depth Ratio 32.05 > 19.02 **** limit exceeded ****

Program ADC Version 8.4.0.12 Copyright © Oasys 1990–2014 Page 5

Printed 07-Sep-2018 Time 09:25