Scribd
Upload
226 views2 pages

Deber

1. A steel pipe is subjected to bending and torque loads. The problem requires determining the outer diameter needed to satisfy two failure theories given the loads, material properties, and a safety factor of 2. 2. Using Mohr's circle, determine the factors of safety for different biaxial stress states in a hot-rolled steel bar, applying two failure theories and using a minimum yield strength of 350 MPa. 3. Given normal and shear stresses on perpendicular faces of a machine part, use Mohr's circle to determine the shear stress in a specified direction and the principal stresses.

Uploaded by

Juan Suarez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
226 views2 pages

Deber

1. A steel pipe is subjected to bending and torque loads. The problem requires determining the outer diameter needed to satisfy two failure theories given the loads, material properties, and a safety factor of 2. 2. Using Mohr's circle, determine the factors of safety for different biaxial stress states in a hot-rolled steel bar, applying two failure theories and using a minimum yield strength of 350 MPa. 3. Given normal and shear stresses on perpendicular faces of a machine part, use Mohr's circle to determine the shear stress in a specified direction and the principal stresses.

Uploaded by

Juan Suarez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

ESCUELA POLITÉCNICA NACIONAL – EPN

FACULTAD DE INGENIERÍA MECÁNICA – FIM

MEC7B3-GR3 – DISEÑO DE MÁQUINAS (2018-A)


Deber
Fecha de entrega: 4-junio-2018

1. A section of steel pipe (SY = 340 MPa) has an inner


diameter di = 60 mm and is subjected to a bending
moment M = 7 kN-m and torque T = 7.8 kN-m, as
shown in the figure. For a safety factor FS = 2,
determine the outer diameter do required if this
member is to be designed in accordance with
a. The maximum-distortion-energy criterion of
failure (von Mises)
b. The maximum-shear-stress criterion of failure

2. A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350 MPa.
Using the Mohr´s circle, determine the factors of safety FS for the following plane stress states applying
the distortion-energy (von Mises) and maximum-shear-stress (Tresca) theories:
a. σxx = 100 MPa, σyy = 100 MPa
b. σxx = 100 MPa, σyy = 50 MPa
c. σxx = 100 MPa, σxy = −75MPa
d. σxx = −50 MPa, σyy = −75 MPa σxy = −50 MPa
e. σxx = 100 MPa, σyy = 20 MPa σxy = −20 MPa

3. At a certain point on the surface of a machine part, the normal stresses


on two mutually perpendicular faces (the x and y faces) are 7 MPa
(compressive) and 3 MPa (tensile), as shown in the figure. The
maximum in-plane shear stress at this point is σxy,max = 10 MPa. Use
Mohr’s circle to determine graphically:
a. The magnitude σxy of the shear stress that acts in the direction
shown on the x and y faces,
b. The in-plane principal stresses at this point. σxy

4. A partir del campo de desplazamientos de un


elemento en el plano xy, demostrar que:
a. La deformación normal en la dirección y
u y
viene dada por  yy 
y
b. Para un plano x’y’, definido por una
rotación θ en sentido anti-horario a partir
del eje x, alrededor del eje z, la deformación
cortante viene dada por:
 xx   yy
 x' y'   sin  2    xy cos  2 
2

Prof. Marco Guamán A. ([email protected])


Oficina: Lab. Máquinas-Herramientas / 311-B
5. The strains on the surface of an experimental device made of pure
aluminum (E = 70 GPa, ν = 0.33) and tested in a space shuttle were
measured by means of strain gages. The gages were oriented as
shown in the figure, and the measured strains were εa = 1100∙10−6,
εb = 1496∙10−6, and εc = −39.44∙10−6. What is the normal stress in
the x direction, σxx?

6. An element of material subjected to plane strain (see figure) has


strains as follows: εxx = 220∙10−6, εyy = 480∙10−6, and γxy = 180∙10−6
(εxy = γxy/2). Using the Mohr’s circle, graphically determine:
a. The strains for an element oriented at an angle θ = 50° and
show these strains on a sketch of a properly oriented element.
b. The principal strains and maximum shear strains, and show
these strains on sketches of properly oriented elements.

7. A rectangular plate in biaxial stress (see figure) is


subjected to normal stresses σxx = 90 MPa (tension)
and σyy = −20 MPa (compression). The plate has
dimensions 400 x 800 x 20 (in mm) and is made of
steel with E = 200 GPa and ν = 0.30. Determine:
a. The principal strains ε1,2 and the maximum in-
plane shear strain εxy,max in the plate.
b. The change ∆t in the thickness of the plate.

Prof. Marco Guamán A. ([email protected])


Oficina: Lab. Máquinas
Máquinas-Herramientas / 311-B

You might also like