13 - TDS - Emaco S43 NT

®
EMACO R307
Single component polymer modified fairing coat. Cosmetic mortar for concrete surfaces
Description • Excellent resistance to freeze / thaw action

EMACO® R307 is a single component acrylic and carbonation
polymer modified repair mortar for use as a • Reduces ingress of water borne salts, such as
"fairing coat" or cosmetic mortar. When mixed chlorides and atmospheric / chemical attack.
with water, as directed, a fine grey trowellable • Subsequent paint coats can be applied with
mortar results which can readily be applied to fill in greater economy.
pores, blowholes and blemishes on a concrete
surface. Packaging
EMACO® R307 is supplied in 20kg bags.
EMACO® R307 can be used as a 'skim' coat prior
to the application of protective coatings. *Typical properties
Colour Light grey
®
EMACO R307 is specially formulated to produce Plastic density 1700kg/m³
a shrinkage compensating mortar with no

Application
cracking when applied in a thin section. Adhesion
EMACO® R307 should be applied to the complete
to concrete and flexibility are excellent.
area with the minimum of trowelling. Leave for a
Primary uses short period before final trowelling. Finishing may
• As a fairing or skim coat to cover and make be aided by flicking a small amount of water onto
good blemishes in concrete surfaces such as the surface, using a paint brush before final
slight honeycombing, blowholes, defects trowelling.
caused by 'sand runs', patch repairs, shutter When used as a "scrape coat" EMACO® R307
movement and grout loss. can be applied with a brush or roller and then the
• Preparatory treatment to concrete to receive a excess scraped off with the edge of a steel float.
thin film protective coating. In this way blow holes and minor blemishes in an
• To produce a uniform surface over repaired otherwise fair faced concrete can be hidden.
areas.
Curing:
Advantages Good curing practice is essential even though
• Precision made, consistent results. EMACO® R307 is specially formulated to prevent
• Requires only the addition of mixing water. shrinkage and cracking. Particular care is
required in hot and windy conditions.
• Shrinkage compensating.
Cure with a single coat of MASTERKURE 181
• Excellent adhesion to concrete.
which is compatible with most subsequent
• Flexible.
protective coatings, or by covering the work with
• Smooth, easily produced finish.
a properly secured plastic sheeting.
• Low permeability
®
EMACO R307
Preparation: Specification clause
It is essential that the surfaces to be bonded are Surface finishing:
sound, clean and uncontaminated. All loose All slight surface imperfections should be made
powdering material must be removed. good by the application of EMACO® R307 as
Concrete surfaces should be thoroughly soaked manufactured by BASF-ME. Applications should
prior to application of EMACO® R307, to ensure a be strictly in accordance with the manufacturer's
saturated, but surface dry condition. instructions.
Void filling: Storage

Deeper voids should be filled prior to the Store out of direct sunlight, clear of the ground on
application of a cosmetic coating by reducing the pallets protected from rainfall. Avoid excessive
amount of water added when mixing to produce a compaction. Failure to comply with the
trowellable putty like mortar. recommended storage conditions may result in
premature deterioration of the product or
Mixing: packaging. For specific storage advice consult
EMACO® R307 is formulated to give an easily BASF's Technical Services Department.
mixed material. For full bag quantities, it is
Safety precautions
preferable to mix the material in a Creteangle or
As with all chemical products, care should be
similar forced action mixer. Alternatively, a slow
taken during use and storage to avoid contact
speed, hand held electric mixer with a suitable
with eyes, mouth, skin and foodstuffs. Treat
paddle can be used. Over mixing should be
splashes to eyes and skin immediately. If
avoided. When mixing full bags, pour 3-4 litres
accidentally ingested, seek medical attention.
water in the mixing vessel and commence mixing.
Reseal containers after use. Use in well ventilated
Add the powder to the water whilst mixing, add
areas and avoid inhalation. For further information
water as required to achieve the desired
refer to the material safety data sheet.
consistency. No more than 7.5 litres of water per
20kg of EMACO® R307 should be added. Note
Field service, where provided, does not constitute
Coverage
supervisory responsibility. For additional
One 20kg bag of EMACO® R307 will typically yield
information contact your local BASF
16 litres of mortar and will cover approximately
representative.
16m² at 1mm thickness.
Equipment care BASF reserves the right to have the true cause of
Tools should be washed with water immediately any difficulty determined by accepted test
after use. methods.
®
EMACO R307
Quality and care
All products originating from BASF’s Dubai, UAE
facility are manufactured under a management
system independently certified to conform to the
requirements of the quality, environmental and
occupational health & safety standards ISO 9001,
ISO 14001 and OHSAS 18001.
12/99 BASF_CC-UAE revised 02/2008
* Properties listed are based on laboratory controlled tests.
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with
any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the
application are beyond our control.
As all BASF technical datasheets are updated on a regular basis it is the user's responsibility to obtain the most recent issue.
BASF Construction Chemicals UAE LLC

P.O. Box 37127, Dubai, UAE
Tel: +971 4 8090800 Fax: +971 4 8851002
Certificate No. Certificate No. Certificate No.
www.basf-cc.ae e-mail: [email protected] 963680 945787 772556

13 - TDS - Emaco S43 NT

Uploaded by

Copyright:

Available Formats

13 - TDS - Emaco S43 NT

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

13 - TDS - Emaco S43 NT

Uploaded by

Copyright:

Available Formats

®

Description • Excellent resistance to freeze / thaw action

a shrinkage compensating mortar with no

Void filling: Storage

12/99 BASF_CC-UAE revised 02/2008

* Properties listed are based on laboratory controlled tests.

BASF Construction Chemicals UAE LLC

You might also like