0105336163190c501V10.

A1C-3
Tina-quant Hemoglobin A1c Gen.3 - Hemolysate and Whole Blood Application
Order information
Analyzer(s) on which cobas c pack(s) can be used
05336163 190 Tina-quant Hemoglobin A1c Gen.3 (150 tests) System ID 07 7455 3 Roche/Hitachi cobas c 311, cobas c 501/502
04528417 190 Calibrator f.a.s. HbA1c (3 x 2 mL) Code 674
05479207 190 PreciControl HbA1c norm (4 × 1 mL) Code 208
05912504 190 PreciControl HbA1c path (4 × 1 mL) Code 209
04528182 190 Hemolyzing Reagent Gen.2 (51 mL)* System ID 07 6873 1
HbA1c Hemolyzing Reagent for Tina‑quant HbA1c For Hemolysate
11488457 122
(1000 mL) Application only
* The value encoded in the instrument settings is 45 mL to account for the dead volume of the bottles.

English • Estimated average glucose [mg/dL] = 28.7 x HbA1c (%) - 46.7

System information The risk of diabetic complications, such as diabetic nephropathy and
retinopathy, increases with poor metabolic control. In accordance with its
Whole Blood Application - Standardized according to IFCC transfer­ function as an indicator for the mean blood glucose level, HbA1c predicts
able to DCCT/NGSP the development of diabetic complications in diabetes patients.3,4
HB-W3: ACN 871 Hemoglobin (Hb) For monitoring long term glycemic control, testing every 3 to 4 months is
generally sufficient. In certain clinical situations, such as gestational
A1-W3: ACN 881 Hemoglobin A1c (HbA1c) diabetes, or after a major change in therapy, it may be useful to measure
HbA1c in 2 to 4 week intervals.6
RWD3: ACN 891 Ratio % HbA1c (acc. to DCCT/NGSP)
Test principle9,10,11
A1CD2: ACN 952 Hemolyzing reagent This method uses TTABa) as the detergent in the hemolyzing reagent to
eliminate interference from leukocytes (TTAB does not lyse leukocytes).
Hemolysate Application - Standardized according to IFCC Sample pretreatment to remove labile HbA1c is not necessary.
transferable to DCCT/NGSP
All hemoglobin variants which are glycated at the β‑chain N‑terminus and
HB-H3: ACN 841 Hemoglobin (Hb) which have antibody-recognizable regions identical to that of HbA1c are
determined by this assay. Consequently, the metabolic state of patients
A1–H3: ACN 851 Hemoglobin A1c (HbA1c) having uremia or the most frequent hemoglobinopathies (HbAS, HbAC,
RHD3: ACN 861 Ratio % HbA1c (acc. to DCCT/NGSP) HbAE) can be determined using this assay.12,13
A1CD2: ACN 952 Hemolyzing reagent a) TTAB = Tetradecyltrimethylammonium bromide
Hemoglobin A1c
Intended use
The HbA1c determination is based on the turbidimetric inhibition
In vitro test for the quantitative determination of mmol/mol hemoglobin immunoassay (TINIA) for hemolyzed whole blood.
(IFCC) and % hemoglobin A1c (DCCT/NGSP) in whole blood or hemolysate
on Roche/Hitachi cobas c systems. HbA1c determinations are useful ▪ Sample and addition of R1 (buffer/antibody)
monitoring of long-term blood glucose control in individuals with diabetes Glycohemoglobin (HbA1c) in the sample reacts with anti-HbA1c
mellitus. Moreover, this test is to be used as an aid in diagnosis of diabetes antibody to form soluble antigen-antibody complexes. Since the specific
and identifying patients who may be at risk for developing diabetes. HbA1c antibody site is present only once on the HbA1c molecule,
Summary1,2,3,4,5,6,7,8 formation of insoluble complexes does not take place.
Hemoglobin (Hb) consists of four protein subunits, each containing a heme ▪ Addition of R3 (buffer/polyhapten) and start of reaction:
moiety, and is the red-pigmented protein located in the erythrocytes. Its
main function is the transport of oxygen and carbon dioxide in blood. Each The polyhaptens react with excess anti-HbA1c antibodies to form an
Hb molecule is able to bind four oxygen molecules. Hb consists of a variety insoluble antibody-polyhapten complex which can be determined
of subfractions and derivatives. Among this heterogeneous group of turbidimetrically.
hemoglobins HbA1c is one of the glycated hemoglobins, a subfraction Hemoglobin
formed by the attachment of various sugars to the Hb molecule. HbA1c is Liberated hemoglobin in the hemolyzed sample is converted to a derivative
formed in two steps by the non-enzymatic reaction of glucose with the having a characteristic absorption spectrum which is measured
N‑terminal amino group of the β‑chain of normal adult Hb (HbA). The first bichromatically during the preincubation phase (sample + R1) of the above
step is reversible and yields labile HbA1c. This is rearranged to form stable immunological reaction. A separate Hb reagent is consequently not
HbA1c in a second reaction step. necessary.
In the erythrocytes, the relative amount of HbA converted to stable HbA1c The final result is expressed as mmol/mol HbA1c or % HbA1c and is
increases with the average concentration of glucose in the blood. The calculated from the HbA1c/Hb ratio as follows:
conversion to stable HbA1c is limited by the erythrocyte's life span of
approximately 100 to 120 days. As a result, HbA1c reflects the average Protocol 1 (mmol/mol HbA1c acc. to IFCC):
blood glucose level during the preceding 2 to 3 months. HbA1c is thus HbA1c (mmol/mol) = (HbA1c/Hb) × 1000
suitable to monitor long-term blood glucose control in individuals with Protocol 2 (% HbA1c acc. to DCCT/NGSP):
diabetes mellitus. Glucose levels closer to the time of the assay have a
greater influence on the HbA1c level.1 HbA1c (%) = (HbA1c/Hb) × 91.5 + 2.15
The approximate relationship between HbA1c and mean blood glucose Reagents – working solutions
values during the preceding 2 to 3 months was analyzed in several studies. R1 Antibody Reagent
A recent study obtained the following correlation:
IFCC standardization (recalculated acc. to ref. 8) MES buffer: 0.025 mol/L; TRIS buffer: 0.015 mol/L, pH 6.2;
• Estimated average glucose [mmol/L] = 0.146 x HbA1c (mmol/mol) + 0.834 HbA1c antibody (ovine serum): ≥ 0.5 mg/mL; detergent;
or stabilizers; preservatives
• Estimated average glucose [mg/dL] = 2.64 x HbA1c (mmol/mol) + 15.03
Standardization acc. to DCCT/NGSP7
• Estimated average glucose [mmol/L] = 1.59 x HbA1c (%) - 2.59 or

2017-11, V 10.0 English 1/8

0105336163190c501V10.0

A1C-3
Tina-quant Hemoglobin A1c Gen.3 - Hemolysate and Whole Blood Application

R3 Polyhapten Reagent HbA1c Hemolyzing Reagent for 500 µL 1000 µL 2000 µL

MES buffer: 0.025 mol/L; TRIS buffer: 0.015 mol/L, pH 6.2; Tina‑quant HbA1c
HbA1c polyhapten: ≥ 8 µg/mL; detergent; stabilizers; Specimen (patient or control) 5 µL 10 µL 20 µL
preservatives 4. Mix using a vibration mixer or by gentle swirling.
R1 is in position A and R3 is in position C. Position B contains H2O for 5. The hemolysate can be used after the solution has changed color from
technical reasons. red to brownish-green (approx. 1‑2 min).
Precautions and warnings Stability of the hemolysate: 4 hours at 15‑25 °C
For in vitro diagnostic use.
Exercise the normal precautions required for handling all laboratory 24 hours at 2‑8 °C
reagents. 6 months at (-15)‑(-25) °C
Disposal of all waste material should be in accordance with local guidelines.
Safety data sheet available for professional user on request. Materials provided
Reagent handling See “Reagents – working solutions” section for reagents.
Ready for use Materials required (but not provided)
Storage and stability ▪ See “Order information” section
A1C-3 ▪ General laboratory equipment
Assay
Shelf life at 2‑8 °C: See expiration date on cobas c pack label.
For optimum performance of the assay follow the directions given in this
On-board in use and 4 weeks document for the analyzer concerned. Refer to the appropriate operator’s
refrigerated on the manual for analyzer‑specific assay instructions.
analyzer: The performance of applications not validated by Roche is not warranted
and must be defined by the user.
Hemolyzing reagent
Whole Blood application for Hb (HB‑W3) and HbA1c (A1‑W3)
Shelf life at 2‑8 °C: See expiration date on cobas c pack label.
When storing at temperatures under 3 °C, the reagent may become cloudy. cobas c 311 test definition Hb (HB-W3)
This has no effect on the function of the reagent and is reversible at higher Assay type 1-Point
temperatures. It is therefore recommended to equilibrate the reagent at
room temperature for approximately 10 minutes and mix thoroughly before Reaction time / Assay points 10 / 23
use.
Wavelength (sub/main) 660 / 376 nm
On-board in use and 4 weeks Reaction direction Increase
refrigerated on the
analyzer: Unit mmol/L (g/dL)
Reagent pipetting Diluent (H2O)
Specimen collection and preparation
For specimen collection and preparation only use suitable tubes or R1 120 μL -
collection containers. R3 24 μL -
Only the specimens listed below were tested and found acceptable.
Sample volumes Sample Sample dilution
Anticoagulated venous or capillary blood or hemolysate.
The only acceptable anticoagulants are Li‑heparin, K2‑EDTA, K3‑EDTA, Sample Diluent
Fluoride/Na2‑EDTA, Na‑Heparin and Fluoride/potassium oxalate. (Hemolyzing
The sample types listed were tested with a selection of sample collection reagent)
tubes that were commercially available at the time of testing, i.e. not all Normal 5 μL 2 μL 180 μL
available tubes of all manufacturers were tested. Sample collection systems
from various manufacturers may contain differing materials which could Decreased 5 μL 2 μL 180 μL
affect the test results in some cases. When processing samples in primary Increased 5 μL 2 μL 180 μL
tubes (sample collection systems), follow the instructions of the tube
manufacturer. cobas c 311 test definition HbA1c (A1-W3)
See the limitations and interferences section for details about possible
sample interferences. Assay type 2-Point End
Reaction time / Assay points 10 / 23‑57
Stability: 3 days at 15‑25 °C
7 days at 2‑8 °C Wavelength (sub/main) 660 / 340 nm
6 months at (-15)‑(-25) °C Reaction direction Increase
Freeze only once. Mix specimen thoroughly after thawing. Unit mmol/L (g/dL)
Hemolysate preparation for Hemolysate Application Reagent pipetting Diluent (H2O)
1. Allow blood specimen and Hemolyzing Reagent for Tina‑quant  HbA1c to
equilibrate at room temperature before use. R1 120 μL -
2. Moderately mix the sample immediately prior to pipetting to ensure a R3 24 μL -
homogeneous mixture of erythrocytes. Take care to avoid the formation of Sample volumes Sample Sample dilution
foam.
Sample Diluent
3. Dilute the sample with Hemolyzing Reagent for Tina‑quant HbA1c
(Cat. No. 11488457 122) in the ratio 1:101 (1+100) using one of the (Hemolyzing
following pipetting schemes. reagent)
Pipette into tubes: Normal 5 μL 2 μL 180 μL

2/8 2017-11, V 10.0 English

0105336163190c501V10.0

A1C-3
Tina-quant Hemoglobin A1c Gen.3 - Hemolysate and Whole Blood Application

Decreased 5 μL 2 μL 180 μL Unit of Measure mM/M

Increased 5 μL 2 μL 180 μL Report Name HbA1c Gen.3 IFCC
Item RWI3
cobas c 501/502 test definition Hb (HB-W3)
Formula (A1-W3/HB-W3) x 1000
Assay type 1-Point
The ratio for HbA1c (mmol/mol HbA1c acc. to IFCC and % HbA1c acc. to
Reaction time / Assay points 10 / 34 DCCT/NGSP) will be automatically calculated after result output of both
Wavelength (sub/main) 660 / 376 nm tests. It is recommended to report % HbA1c values (DCCT/NGSP) to one
decimal place and mmol/mol HbA1c values (IFCC) without decimal places,
Reaction direction Increase which can be entered in the editable field “expected values”.
Unit mmol/L (g/dL) Hemolysate Application for Hb (HB‑H3) and HbA1c (A1‑H3)

Reagent pipetting Diluent (H2O) cobas c 311 test definition Hb (HB-H3)

R1 120 μL - Assay type 1-Point
R3 24 μL - Reaction time / Assay points 10 / 23
Sample volumes Sample Sample dilution Wavelength (sub/main) 660 / 376 nm
Sample Diluent Reaction direction Increase
(Hemolyzing
Unit mmol/L (g/dL)
reagent)
Reagent pipetting Diluent (H2O)
Normal 5 μL 2 μL 180 μL
Decreased 5 μL 2 μL 180 μL R1 120 μL -
Increased 5 μL 2 μL 180 μL R3 24 μL -
Sample volumes Sample Sample dilution
cobas c 501/502 test definition HbA1c (A1-W3)
Sample Diluent
Assay type 2-Point End (Hemolyzing
Reaction time / Assay points 10 / 34-70 reagent)
Wavelength (sub/main) 660 / 340 nm Normal 5 μL - -

Reaction direction Increase Decreased 5 μL - -

Increased 5 μL - -
Unit mmol/L (g/dL)
Reagent pipetting Diluent (H2O) cobas c 311 test definition HbA1c (A1-H3)
R1 120 μL - Assay type 2-Point End
R3 24 μL - Reaction time / Assay points 10 / 23-57
Sample volumes Sample Sample dilution Wavelength (sub/main) 660 / 340 nm
Sample Diluent Reaction direction Increase
(Hemolyzing
Unit mmol/L (g/dL)
reagent)
Reagent pipetting Diluent (H2O)
Normal 5 μL 2 μL 180 μL
Decreased 5 μL 2 μL 180 μL R1 120 μL -
Increased 5 μL 2 μL 180 μL R3 24 μL -
Sample volumes Sample Sample dilution
Ratio definition for mmol/mol HbA1c and % HbA1c calculation
Sample Diluent
Protocol 1 (mmol/mol HbA1c acc. to IFCC):
(Hemolyzing
Abbreviated ratio name RWI3 reagent)
Equation (A1-W3/HB-W3) × 1000 Normal 5 μL - -
Unit mmol/mol Decreased 5 μL - -
Protocol 2 (% HbA1c acc. to DCCT/NGSP): Increased 5 μL - -
Abbreviated ratio name RWD3 (891)
cobas c 501/502 test definition Hb (HB-H3)
Equation (A1-W3/HB-W3) × 91.5 + 2.15
Assay type 1‑Point
Unit %
Reaction time / Assay points 10 / 34
Protocol 2 is already implemented in the application (ACN 891). The
mmol/mol HbA1c values according to Protocol 1 (IFCC) must be manually Wavelength (sub/main) 660 / 376 nm
calculated according to the above equation. If requested a calculated test
with the formula in protocol 1 can be programmed under Utility > calculated Reaction direction Increase
test on the Roche/Hitachi cobas c 311 analyzer and on the Roche/Hitachi Unit mmol/L (g/dL)
cobas c 501/502 analyzers. Please use the following settings:
Reagent pipetting Diluent (H2O)
Sample Type Supernt.

2017-11, V 10.0 English 3/8

0105336163190c501V10.0

A1C-3
Tina-quant Hemoglobin A1c Gen.3 - Hemolysate and Whole Blood Application

R1 120 μL - Hb
R3 24 μL - Calibrators S1-S2: C.f.a.s. HbA1c
Sample volumes Sample Sample dilution Calibration mode Linear
Sample Diluent HbA1c
(Hemolyzing Calibrators S1-S6: C.f.a.s. HbA1c
reagent)
Calibration mode Spline
Normal 5 μL - -
Calibration frequency Hb and HbA1c: full calibration is
Decreased 5 μL - - recommended
Increased 5 μL - - - after 29 days during shelf life
cobas c 501/502 test definition HbA1c (A1-H3) - after reagent lot change
Assay type 2‑Point End - as required following quality control
procedures
Reaction time / Assay points 10 / 34-70
Always calibrate both assays (Hb
Wavelength (sub/main) 660 / 340 nm
and HbA1c) in parallel. Automatic
Reaction direction Increase calibration at QC failure should be
Unit mmol/L (g/dL) deactivated.
Reagent pipetting Diluent (H2O) Calibration interval may be extended based on acceptable verification of
calibration by the laboratory.
R1 120 μL - Traceability: This method has been standardized against the approved
R3 24 μL - IFCC reference method for the measurement of HbA1c in human blood 14,15
and can be transferred to results traceable to DCCT/NGSP by calculation.
Sample volumes Sample Sample dilution Note for Whole Blood and Hemolysate Application
Sample Diluent Enter the assigned lot-specific and application-specific value of the
(Hemolyzing calibrator. Use the appropriate C.f.a.s. HbA1c calibrator only.
reagent) The cobas c Hemolyzing Reagent Gen.2 pack, 51 mL,
Normal 5 μL - - Cat. No. 04528182 190, needs to be available on the analyzer otherwise
the calibration cannot be performed.
Decreased 5 μL - - Quality control for Whole Blood and Hemolysate Application
Increased 5 μL - - For quality control, use control materials as listed in the "Order information"
Ratio definition for HbA1c (mmol/mol (IFCC) or % (DCCT/NGSP)) cal­ section.
culation In addition, other suitable control material can be used.
The control intervals and limits should be adapted to each laboratory’s
Protocol 1 (mmol/mol HbA1c acc. to IFCC): individual requirements. Values obtained should fall within the defined
Abbreviated ratio name RHI3 limits. Each laboratory should establish corrective measures to be taken if
values fall outside the defined limits.
Equation (A1-H3/HB-H3) x 1000
Follow the applicable government regulations and local guidelines for
Unit mmol/mol quality control.
Protocol 2 (% HbA1c acc. to DCCT/NGSP): Calculation for Whole Blood and Hemolysate Application
Abbreviated ratio name RHD3 (861) Hb, HbA1c
Roche/Hitachi cobas c systems automatically calculate the analyte
Equation (A1-H3/HB-H3) x 91.5 + 2.15 concentration of each sample.
Unit % HbA1c ratio calculation:
Protocol 2 is already implemented in the application (ACN 861). The For calculation of the mmol/mol HbA1c value (IFCC) and the percent
mmol/mol HbA1c values according to Protocol 1 (IFCC) must be manually HbA1c value (DCCT/NGSP), refer to the Test principle and Ratio
calculated according to the above equation. If requested a calculated test definition for mmol/mol HbA1c and % HbA1c calculation sections in this
with the formula in protocol 1 can be programmed under Utility > calculated method sheet.
test on the Roche/Hitachi cobas c 311 analyzer and on the Roche/Hitachi Limitations – interference for Whole Blood and Hemolysate
cobas c 501/502 analyzers. Please use the following settings: Application12,13,16,17,18,19,20,21,22,23
Sample Type Supernt. 1. For diagnostic purposes, mmol/mol HbA1c values (IFCC) and % HbA1c
values (DCCT/NGSP) should be used in conjunction with information from
Unit of Measure mM/M other diagnostic procedures and clinical evaluations.
Report Name HbA1c Gen.3 IFCC 2. The test is designed only for accurate and precise measurement of
mmol/mol HbA1c (IFCC) and % HbA1c (DCCT/NGSP). The individual
Item RHI3 results for total Hb and HbA1c concentration should not be reported.
Formula (A1-H3/HB-H3) x 1000 3. As a matter of principle, care must be taken when interpreting any HbA1c
The ratio for HbA1c (mmol/mol HbA1c acc. to IFCC and % HbA1c acc. to result from patients with Hb variants. Abnormal hemoglobins might affect
DCCT/NGSP) will be automatically calculated after result output of both the half life of the red cells or the in vivo glycation rates. In these cases
tests. It is recommended to report % HbA1c values (DCCT/NGSP) to one even analytically correct results do not reflect the same level of glycemic
decimal place and mmol/mol HbA1c values (IFCC) without decimal places, control that would be expected in patients with normal hemoglobin.21
which can be entered in the editable field “expected values”. Whenever it is suspected that the presence of an Hb variant (e.g. HbSS,
HbCC or HbSC) affects the correlation between the HbA1c value and
Calibration for Whole Blood and Hemolysate Application glycemic control, HbA1c must not be used for the diagnosis of diabetes
mellitus.

4/8 2017-11, V 10.0 English

0105336163190c501V10.0

A1C-3
Tina-quant Hemoglobin A1c Gen.3 - Hemolysate and Whole Blood Application

4. Any cause of shortened erythrocyte survival or decrease in mean Limit of Detection = 0.62 mmol/L (1.00 g/dL)
erythrocyte age will reduce exposure of erythrocytes to glucose with a HbA1c:
consequent decrease in mmol/mol HbA1c values (IFCC) and % HbA1c
values (DCCT/NGSP), even though the time-averaged blood glucose level Limit of Blank = 0.12 mmol/L (0.19 g/dL)
may be elevated. Causes of shortened erythrocyte lifetime might be Limit of Detection = 0.18 mmol/L (0.29 g/dL)
hemolytic anemia or other hemolytic diseases, homozygous sickle cell trait, The Limit of Blank and Limit of Detection were determined in accordance
pregnancy, recent significant or chronic blood loss, etc. Similarly, recent with the CLSI (Clinical and Laboratory Standards Institute) EP17‑A
blood transfusions can alter the mmol/mol HbA1c values (IFCC) and requirements.
% HbA1c values (DCCT/NGSP).Caution should be used when interpreting
the HbA1c results from patients with these conditions. HbA1c must not be The Limit of Blank is the 95th percentile value from n ≥ 60 measurements of
used for the diagnosis of diabetes mellitus in the presence of such analyte‑free samples over several independent series. The Limit of Blank
conditions. corresponds to the concentration below which analyte‑free samples are
found with a probability of 95 %.
5. Glycated HbF is not detected by the assay as it does not contain the
glycated β‑chain that characterizes HbA1c. However, HbF is measured in The Limit of Detection is determined based on the Limit of Blank and the
the total Hb assay and as a consequence, specimens containing high standard deviation of low concentration samples.
amounts of HbF (> 10 %) may result in lower than expected mmol/mol The Limit of Detection corresponds to the sample concentration which leads
HbA1c values (IFCC) and % HbA1c values (DCCT/NGSP).13,23 with a probability of 95 % to a measurement result above the Limit of Blank.
6. mmol/mol HbA1c values (IFCC) and % HbA1c values (DCCT/NGSP) are Expected values
not suitable for the diagnosis of gestational diabetes.24 Protocol 1 (mmol/mol HbA1c acc. to IFCC): 29‑42 mmol/mol HbA1c27
7. In very rare cases of rapidly evolving type 1 diabetes the increase of the Protocol 2 (% HbA1c acc. to DCCT/NGSP): 4.8‑5.9 % HbA1c27
HbA1c values might be delayed compared to the acute increase in glucose
concentrations. In these conditions diabetes mellitus must be diagnosed This reference range was obtained by measuring 474 well-characterized
based on plasma glucose concentrations and/or the typical clinical healthy individuals without diabetes mellitus. HbA1c levels higher than the
symptoms.24 upper end of this reference range are an indication of hyperglycemia during
the preceding 2 to 3 months or longer. According to the recommendations
Criterion: Recovery within ± 10 % of initial value. of the American Diabetes Association values above 48 mmol/mol HbA1c
Icterus:20 No significant interference up to an I index of 60 for conjugated (IFCC) or 6.5 % HbA1c (DCCT/NGSP) are suitable for the diagnosis of
and unconjugated bilirubin (approximate conjugated and unconjugated diabetes mellitus.24,28 Patients with HbA1c values in the range of
bilirubin concentration: 1026 µmol/L or 60 mg/dL). 39‑46 mmol/mol HbA1c (IFCC) or 5.7‑6.4 % HbA1c (DCCT/NGSP) may be
Lipemia (Intralipid):20 No significant interference up to an Intralipid at risk of developing diabetes.24,28
concentration of 600 mg/dL. There is poor correlation between triglycerides HbA1c levels may reach 195 mmol/mol (IFCC) or 20 % (DCCT/NGSP) or
concentration and turbidity. higher in poorly controlled diabetes. Therapeutic action is suggested at
Glycemia: No significant interference up to a glucose level of 55.5 mmol/L levels above 64 mmol/mol HbA1c (IFCC) or 8 % HbA1c (DCCT/NGSP).
(1000 mg/dL). A fasting sample is not required. Diabetes patients with HbA1c levels below 53 mmol/mol (IFCC) or 7 %
(DCCT/NGSP) meet the goal of the American Diabetes Association.19,18
Rheumatoid factors: No significant interference from rheumatoid factors up
to a concentration of 750 IU/mL. HbA1c levels below the established reference range may indicate recent
episodes of hypoglycemia, the presence of Hb variants, or shortened
Drugs: No interference was found at therapeutic concentrations using lifetime of erythrocytes.
common drug panels.25,26
Each laboratory should investigate the transferability of the expected values
Other: No cross reactions with HbA0, HbA1a, HbA1b, acetylated to its own patient population and if necessary determine its own reference
hemoglobin, carbamylated hemoglobin, glycated albumin and labile HbA1c ranges.
were found for the anti-HbA1c antibodies used in this kit.
For diagnostic purposes, the results should always be assessed in Specific performance data
conjunction with the patient’s medical history, clinical examination and other Representative performance data on the analyzers are given below.
findings. Results obtained in individual laboratories may differ.
ACTION REQUIRED Precision
Special Wash Programming: The use of special wash steps is mandatory Precision was determined using human samples and controls in
when certain test combinations are run together on Roche/Hitachi accordance with the CLSI (Clinical and Laboratory Standards Institute) EP5
cobas c systems. The latest version of the carry‑over evasion list can be requirements with repeatability and intermediate precision (2 aliquots per
found with the NaOHD-SMS-SmpCln1+2-SCCS Method Sheets. For further run, 2 runs per day, 21 days). The following results were obtained (data
instructions refer to the operator’s manual. cobas c 502 analyzer: All based on DCCT/NGSP values):
special wash programming necessary for avoiding carry‑over is available
via the cobas link, manual input is required in certain cases. Whole Blood Application:
Where required, special wash/carry‑over evasion programming must Repeatability Mean SD CV
be implemented prior to reporting results with this test.
% HbA1c % %
Limits and ranges
Measuring range PreciControl HbA1c norm 5.3 0.07 1.3
Hemoglobin: 2.48‑24.8 mmol/L (4‑40 g/dL). PreciControl HbA1c path 9.9 0.11 1.1
HbA1c: 0.186‑1.61 mmol/L (0.3‑2.6 g/dL) Human sample 1 4.4 0.07 1.6
This corresponds to a measuring range of 23‑196 mmol/mol HbA1c (IFCC) Human sample 2 5.6 0.09 1.6
and 4.2‑20.1 % HbA1c (DCCT/NGSP) at a typical hemoglobin
concentration of 8.2 mmol/L (13.2 g/dL). Human sample 3 8.0 0.08 1.0
In rare cases of “>Test” flags which might occur with the use of the whole Human sample 4 10.6 0.11 1.1
blood application, remix the whole blood sample and repeat the analysis
with the same settings. Intermediate precision Mean SD CV
It is recommended to switch the auto rerun function off. % HbA1c % %
Lower limits of measurement
PreciControl HbA1c norm 5.3 0.08 1.4
Limit of Blank and Limit of Detection
Hemoglobin: PreciControl HbA1c path 9.9 0.15 1.5
Limit of Blank = 0.31 mmol/L (0.50 g/dL) Human sample 1 4.4 0.09 1.9

2017-11, V 10.0 English 5/8

0105336163190c501V10.0

A1C-3
Tina-quant Hemoglobin A1c Gen.3 - Hemolysate and Whole Blood Application

Human sample 2 5.6 0.11 2.0 % HbA1c (DCCT/NGSP) values for human blood samples obtained on a
Roche/Hitachi cobas c 501 analyzer using the Tina‑quant Hemoglobin A1c
Human sample 3 8.0 0.11 1.4 Gen.3 reagent with the whole blood application (y) were compared with
Human sample 4 10.6 0.16 1.5 those determined using the Tina‑quant Hemoglobin A1c Gen.2 reagent with
the hemolysate application on a COBAS INTEGRA 800 analyzer (x).
Hemolysate Application:
Sample size (n) = 80
Repeatability Mean SD CV
Mean difference -0.09 % HbA1c
% HbA1c % %
Lower 95 % confidence interval of -0.46 % HbA1c
PreciControl HbA1c norm 5.1 0.07 1.3 differences
PreciControl HbA1c path 10.2 0.10 1.0 Upper 95 % confidence interval of 0.28 % HbA1c
Human sample 1 4.3 0.06 1.4 differences
Human sample 2 5.6 0.07 1.2 The sample concentrations were between 4.7 % and 9.8 % (DCCT/NGSP
Human sample 3 8.2 0.08 1.0 values).
Human sample 4 10.9 0.11 1.0 Hemolysate Application:
% HbA1c (DCCT/NGSP) values for human blood samples obtained on a
Intermediate precision Mean SD CV Roche/Hitachi cobas c 501 analyzer using the Tina‑quant Hemoglobin A1c
Gen.3 reagent with the whole blood application (y) were compared with
% HbA1c % % those determined using the Tina‑quant Hemoglobin A1c Gen.2 reagent with
PreciControl HbA1c norm 5.1 0.11 2.2 the hemolysate application on a COBAS INTEGRA 800 analyzer (x).
PreciControl HbA1c path 10.2 0.21 2.0 Sample size (n) = 111
Human sample 1 4.3 0.10 2.3 Mean difference -0.19 % HbA1c
Human sample 2 5.6 0.09 1.6 Lower 95 % confidence interval of -0.52 % HbA1c
Human sample 3 8.2 0.16 1.9 differences
Human sample 4 10.9 0.22 2.0 Upper 95 % confidence interval of 0.14 % HbA1c
differences
Method comparison
The sample concentrations were between 4.6 % and 9.9 % (DCCT/NGSP
Evaluation of method comparison data is according to NGSP certification
criteria. The mean difference between the two methods and the 95 % values).
confidence intervals of the differences in the range from 4‑10 % % HbA1c (DCCT/NGSP) values for human blood samples obtained on a
(DCCT/NGSP) are given. 95 % of the differences between the values Roche/Hitachi cobas c 501 analyzer using the Tina‑quant Hemoglobin A1c
obtained for individual samples with both methods fall within the range Gen.3 reagent with the hemolysate application (y) were compared with
defined by the lower and upper 95 % confidence intervals of the those determined using the Tina‑quant Hemoglobin A1c Gen.2 reagent with
differences. the whole blood application (x).
Whole Blood Application:
Sample size (n) = 84
% HbA1c (DCCT/NGSP) values for human blood samples obtained on a
Roche/Hitachi cobas c 501 analyzer using the Tina‑quant Hemoglobin A1c Mean difference -0.06 % HbA1c
Gen.3 reagent with the whole blood application (y) were compared with
those determined using the corresponding reagent with the hemolysate Lower 95 % confidence interval of -0.53 % HbA1c
application on a COBAS INTEGRA 800 analyzer (x). differences
Upper 95 % confidence interval of 0.41 % HbA1c
Sample size (n) = 80
differences
Mean difference 0.07 % HbA1c
The sample concentrations were between 5.5 % and 9.9 % (DCCT/NGSP
Lower 95 % confidence interval of -0.27 % HbA1c values).
differences
% HbA1c (DCCT/NGSP) values for human blood samples obtained on a
Upper 95 % confidence interval of 0.42 % HbA1c Roche/Hitachi cobas c 501 analyzer using the Tina‑quant Hemoglobin A1c
differences Gen.3 reagent with the hemolysate application (y) were compared with
those determined using the Tina‑quant Hemoglobin A1c Gen.2 reagent with
The sample concentrations were between 4.7 % and 9.8 % (DCCT/NGSP the hemolysate application on a COBAS INTEGRA 800 analyzer (x).
values).
Sample size (n) = 111
% HbA1c (DCCT/NGSP) values for human blood samples obtained on a
Roche/Hitachi cobas c 501 analyzer using the Tina‑quant Hemoglobin A1c Mean difference -0.35 % HbA1c
Gen.3 reagent with the whole blood application (y) were compared with
those determined using the Tina‑quant Hemoglobin A1c Gen.2 reagent with Lower 95 % confidence interval of -0.68 % HbA1c
the whole blood application (x). differences
Upper 95 % confidence interval of -0.02 % HbA1c
Sample size (n) = 82
differences
Mean difference 0.07 % HbA1c
The sample concentrations were between 4.7 % and 9.9 % (DCCT/NGSP
Lower 95 % confidence interval of -0.50 % HbA1c values).
differences
% HbA1c (DCCT/NGSP) values for human blood samples obtained on a
Upper 95 % confidence interval of 0.65 % HbA1c Roche/Hitachi cobas c 501 analyzer using the Tina‑quant Hemoglobin A1c
differences Gen.3 reagent with the hemolysate application (y) were compared with
those determined using the Tina‑quant Hemoglobin A1c Gen.2 reagent with
The sample concentrations were between 5.0 % and 9.9 % (DCCT/NGSP the hemolysate application (x).
values).

6/8 2017-11, V 10.0 English

0105336163190c501V10.0

A1C-3
Tina-quant Hemoglobin A1c Gen.3 - Hemolysate and Whole Blood Application

Sample size (n) = 113 13 Chang J, Hoke C, Ettinger B, et al. Evaluation and Interference Study
of Hemoglobin A1c Measured by Turbidimetric Inhibition Immunoassay.
Mean difference -0.10 % HbA1c Am J Clin Pathol 1998;109(3):274-278.
Lower 95 % confidence interval of -0.49 % HbA1c 14 Kobold U, Jeppsson JO, Duelffer T, et al. Candidate reference methods
differences for hemoglobin A1c based on peptide mapping. Clin Chem
Upper 95 % confidence interval of 0.31 % HbA1c 1997;43:1944-1951.
differences 15 Jeppsson JO, Kobold U, Finke A, et al. Approved IFCC reference
method for the measurement of HbA1c in human blood. Clin Chem Lab
The sample concentrations were between 4.8 % and 9.7 % (DCCT/NGSP Med 2002;40:78-89.
values).
16 Martina WV, Martijn EG, van der Molen M, et al. β-N-terminal
Analytical specificity for Whole Blood and Hemolysate Application glycohemoglobins in subjects with common hemoglobinopathies:
relation with fructosamine and mean erythrocyte age. Clin Chem
Hb derivatives Labile HbA1c (pre-HbA1c), acetylated Hb, and 1993;39:2259-2265.
carbamylated Hb do not affect the assay results. 17 Weykamp CW, Penders TJ, Muskiet FAJ, et al. Influence of
Hb variants Specimens containing high amounts of HbF hemoglobin variants and derivatives on glycohemoglobin
(> 10 %) may yield lower than expected HbA1c determinations, as investigated by 102 laboratories using 16 methods.
Clin Chem 1993;39:1717-1723.
results.
18 American Diabetes Association. Standards of Medical Care for patients
Please note with diabetes mellitus. Diabetes Care [Suppl.] 1995;18(1):8-15.
According to the consensus statement of the American Diabetes 19 Sacks BW, Bruns DE, Goldstein DE, et al. Guidelines and
Association (ADA), the European Association for the Study of Diabetes recommendations for laboratory analysis in the diagnosis and
(EASD), the International Federation of Clinical Chemistry and Laboratory management of diabetes mellitus. Clin Chem 2002;48:436-472.
Medicine (IFCC) and International Diabetes Federation (IDF) HbA1c results
should be reported in parallel, both in mmol/mol (IFCC) and % 20 Glick MR, Ryder KW, Jackson SA. Graphical Comparisons of
(DCCT/NGSP) values.29 In addition an HbA1c derived estimated average Interferences in Clinical Chemistry Instrumentation.
glucose concentration can be reported which can be calculated according Clin Chem 1986;32:470-475.
to the equations given in the Summary section of this method sheet. Former 21 Miedema K. Influence of hemoglobin variants on the determination of
% HbA1c (IFCC) values must not be used due to the risk of mix up / glycated hemoglobin. Klin Lab 1993;39:1029-1032.
misinterpretation with the % HbA1c (DCCT/NGSP) values.
22 Niederau C, Coe A, Katayama Y. Interference of Non-glucose Adducts
References on the Determination of Glycated Hemoglobins. Klin Lab
1 Goldstein DE, Little RR, Lorenz RA, et al. Tests of glycemia in 1993;39:1015-1023.
diabetes. Diabetes Care 1995;18:896-909. 23 Rohlfing C, Connolly J, England J, et al. Effect of Elevated Fetal
2 Goldstein DE, Little RR. More than you ever wanted to know (but need Hemoglobin on HbA1c Measurements: Four Common Assay Methods
to know) about glycohemoglobin testing. Diabetes Care compared to the IFCC Reference Method. Poster Abstract AACC
1994;17:938-939. Annual Meeting 2006, Chicago. Clin Chem 2006;52(6) Suppl A 108.
3 The Diabetes Control and Complications Trial Research Group. The 24 International Expert Committee Report on the Role of the A1C Assay in
effect of intensive treatment of diabetes on the development and the Diagnosis of Diabetes. Diabetes Care 2009;32(7):1327-1334.
progression of long-term complications in insulin-dependent diabetes 25 Breuer J. Report on the Symposium “Drug effects in Clinical Chemistry
mellitus. N Engl J Med 1993;329:977-986. Methods”. Eur J Clin Chem Clin Biochem 1996;34:385-386.
4 UK Prospective Diabetes Study (UKPDS) group. Intensive blood 26 Sonntag O, Scholer A. Drug interference in clinical chemistry:
glucose control with sulfonylureas or insulin compared with recommendation of drugs and their concentrations to be used in drug
conventional treatment and risk of complications in patients with type 2 interference studies. Ann Clin Biochem 2001;38:376-385.
diabetes (UKPDS 33). Lancet 1998;352:837-853.
27 Junge,W, Wilke B, Halabi A, et al. Determination of reference levels in
5 Finke A, Kobold U, Hoelzel W, et al. Preparation of a candidate primary adults for hemoglobin A1c (HbA1c). Poster presentation
reference material for the international standardization of HbA1c EUROMEDLAB, Barcelona 2003.
determinations. Clin Chem Lab Med 1998;36(5):299-308.
28 Diagnosis and Classification of Diabetes Mellitus. Diabetes Care
6 Goldstein DE, Little RR, Wiedmeyer HM, et al. Glycated hemoglobin: 2010;33(1):62-69.
methodologies and clinical applications. Clin Chem 1986;32:B64-B70.
29 Consensus statement on the worldwide standardization of the
7 Nathan DM, Kuenen J, Borg R, et al. Translating the A1C assay into hemoglobin A1c measurement. American Diabetes Association,
estimated average glucose values. Diabetes Care 2008;31:1473-1478. European Association for the Study of Diabetes, International
8 Bunn HF, Gabbay KH, Gallop PM. The glycosylation of hemoglobin: Federation of Clinical Chemistry and Laboratory Medicine and
relevance to diabetes mellitus. Science 1978;200:21-27. International Diabetes Federation Consensus Committee. Diabetes
Care 2007;30:2399-2400.
9 Zander R, Lang W, Wolf HU. Alkaline haematin D-575, a new tool for
the determination of haemoglobin as an alternative to the A point (period/stop) is always used in this Method Sheet as the decimal
cyanhaemiglobin method. I. Description of the method. Clin Chim Acta separator to mark the border between the integral and the fractional parts of
1984;136:83-93. a decimal numeral. Separators for thousands are not used.
10 Wolf HU, Lang W, Zander R. Alkaline haematin D-575, a new tool for Symbols
the determination of haemoglobin as an alternative to the Roche Diagnostics uses the following symbols and signs in addition to
cyanhaemiglobin method. II. Standardization of the method using pure those listed in the ISO 15223‑1 standard (for USA: see
chlorohaemin. Clin Chim Acta 1984;136:95-104. https://usdiagnostics.roche.com for definition of symbols used):
11 Little RR, Wiedmeyer HM, England JD, et al. Interlaboratory
standardization of measurements of glycohemoglobins. Clin Chem Contents of kit
1992;38:2472-2478. Volume after reconstitution or mixing
12 Frank EL, Moulton L, Little RR, et al. Effects of hemoglobin C and S
traits on seven glycated hemoglobin methods. Clin Chem GTIN Global Trade Item Number
2000;46(6):864-867.
COBAS, COBAS C, COBAS INTEGRA, PRECICONTROL and TINA‑QUANT are trademarks of Roche.
All other product names and trademarks are the property of their respective owners.

2017-11, V 10.0 English 7/8

0105336163190c501V10.0

A1C-3
Tina-quant Hemoglobin A1c Gen.3 - Hemolysate and Whole Blood Application

Additions, deletions or changes are indicated by a change bar in the margin.

© 2017, Roche Diagnostics

Roche Diagnostics GmbH, Sandhofer Strasse 116, D-68305 Mannheim

www.roche.com

8/8 2017-11, V 10.0 English