New

ST.
PETER’S ENGINEERING COLLEGE

(Approved by AICTE, Affiliated to JNTUH Hyderabad)
Opp: AP Forest Academy, Dhullapally, Near Kompally, Secunderabad - 500010
DEPARTMENT
OF
MECHANICAL ENGINEERING
Name of the course : ENGINEERING GRAPHICS
Name of the Faculty : S.JABIULLA
Class : I Year B.Tech. I,II – Sem MECH,ECE,CSE
Academic Year : 2017-18
Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

Tel: 040-6522 2235 * Mobile :9959222268,Email: principal@stpetershyd.com * www.stpetershyd.com
CERTIFICATE OF AUTHENTICATION
This is to certify that S.JABIULLA of MECHANICAL ENGINEERING Department has
prepared the course material for Engineering Graphics, Code: ME106ES/ME205ES of Jawaharlal
Nehru Technological University, Hyderabad for the academic year 2017 – 18. The contents of this
course/teaching module have not been reproduced elsewhere in any books or journals.
This is the sole property of St. Peter’s Engineering College, Hyderabad to be referred by staff
and students.
Name of the Faculty: S.Jabiulla

Signature Principal
College Seal

VISION OF THE INSTITUTE:
Our vision is to promote quality education accessible to all sections of the society without any
discrimination of caste, creed, color, gender and religion and helps students to discover their true
potential.
MISSION OF THE INSTITUTE:

 To provide integrated, continuous and wholesome development of students by equipping them
with knowledge and skills,social values and ethics, scientific attitude and orientation for
lifelong education and mould them into useful citizens of the society.
 To create an environment conducive to inhabitating their total involvement and participation of
the students, faculty, staff and management. In making the institution into a centre of
excellence by imparting quality technical education and also arm the students with the
competence to be at the forefront of cutting edge technology and entrepreneurship in the highly
competitive global market.
VISION OF THE MECHNICAL ENGINEERING DEPARTMENT
The Mechanical Engineering Department strives to be recognized globally for outstanding
education and research leading to well-qualified engineers, who are innovative, entrepreneurial and
successful in solving problems of society.
MISSION
 Imparting quality education to students to enhance their skills and make them globally
competitive.
 Prepare its graduates to pursue life-long learning, serve the profession and meet
intellectual, ethical and career challenges.
 To train students to take up projects in core and inter-disciplinary areas in tune.

COURSE OBJECTIVE
 To develop the ability to communicate with others through the language of technical drawing
and sketching
 To develop an understanding for size specification procedures and use of SI and traditional
units of linear measure.
 Learn to sketch and take field dimensions.
 Learn to take data and transform it into graphic drawings.
SCOPE:
• It is the graphic language from which a trained person can visualize the object.
• Drawings prepared in one country may be utilized in any other country, irrespective of the
language spoken there. Hence, engineering drawing is called the universal language of
engineers.
• By means of drawing, the shape, size, finish, colour and construction of any object can be
described accurately and clearly in the simplest and shortest way.
APPLICATIONS:
Machine Components, Internal Combustion Engines ,Robotics & Automation in Mechanical
& Production Engineering.
Structures, plan of buildings, Multi storeyed Complexes, town planning etc in Civil &
Architectural Engineering.
Circuit Layouts, Electrical wiring diagrams, panel design etc in Electrical Engineering.
Schematic diagrams of printed Circuits, Microprocessors, Integrated Circuits etc in Electronics
including Computer Science Engineering.
Communication network, satellite transmitting pictures, TV telecasting etc in Communication
Engineering.

PROGRAMMES EDUCATIONAL OBJECTIVES
 PEO1:To prepare the students to excel in undergraduate and postgraduate in Mechanical
Engineering to mould their careers for successful employment in industry, academic and
entrepreneurial activities.
 PEO2:Graduates of Mechanical Engineering program will analyze and synthesize data and
apply technical concepts which lead to the design of new products, improve upon existing
products and systems and develop technical problem solving skills.
 PEO3:To provide a passionate academic environment for students that encourage learning of
emerging technologies, acquire leadership qualities and guidelines needed for a successful
career in lifelong learning.
PROGRAM OUTCOMES
Apply the knowledge of mathematics, science,
engineering fundamentals, and an engineering
1 ENGINEERING KNOWLEDGE
specialization to the solution of complex
engineering problems.
Identify, formulate, research literature, and
analyze complex engineering problems
2 PROBLEM ANALYSIS reaching substantiated conclusions using first
principles of mathematics, natural sciences,
and engineering sciences.
Design solutions for complex engineering
problems and design system components or
DESIGN/DEVELOPMENT OF processes that meet the specified needs with
3
SOLUTIONS appropriate consideration for the public health
and safety, and the cultural, societal, and
environmental considerations.
Use research-based knowledge and research
methods including design of experiments,
4 CONDUCT INVESTIGATIONS analysis and interpretation of data, and
OF COMPLEX PROBLEMS synthesis of the information to provide valid
conclusions.
Create, select, and apply appropriate
techniques, resources, and modern engineering
5 MODERN TOOL USAGE and IT tools including prediction and
modelling to complex engineering activities
with an understanding of the limitations.
Apply reasoning informed by the contextual
knowledge to assess societal, health, safety,
THE ENGINEER AND
6 legal and cultural issues and the consequent
SOCIETY
responsibilities relevant to the professional
engineering practice.

Understand the impact of the professional
engineering solutions in societal and
ENVIRONMENT AND
7 environmental contexts, and demonstrate the
SUSTAINABILITY
knowledge of, and need for sustainable
development.
Apply ethical principles and commit to
8 ETHICS professional ethics and responsibilities and
norms of the engineering practice.
Function effectively as an individual, and as a
INDIVIDUAL AND TEAM
9 member or leader in diverse teams, and in
WORK
multidisciplinary settings.
Communicate effectively on complex
engineering activities with the engineering
community and with society at large, such as,
10 COMMUNICATION being able to comprehend and write effective
reports and design documentation, make
effective presentations, give and receive clear
instructions.
Demonstrate knowledge and understanding of
the engineering and management principles
PROJECT MANAGEMENT and apply these to one’s own work, as a
11
AND FINANCE member and leader in a team, to manage
projects and in multidisciplinary
environments.
Recognize the need for, and have the
preparation and ability to engage in
12 LIFE-LONG LEARNING
independent and life-long learning in the
broadest context of technological change.
PROGRAM SPECIFIC OUTCOMES
 PSO1:To produce engineering professionals capable of synthesizing and

analyzing Mechanical systems including allied engineering streams.
 PSO2:An ability to adopt and integrate current technologies in the design and
manufacturing domain to enhance efficiency.

ME106ES/ME205ES: ENGINEERING GRAPHICS
B.Tech. I Year II Sem. L /T/P/D/C 2/0/0/4/4
Pre-requisites: None
Course objectives:
 To provide basic concepts in engineering drawing.

 To impart knowledge about standard principles of orthographic projection of
objects.
 To draw sectional views and pictorial views of solids.
Course Outcomes:
 Ability to prepare working drawings to communicate the ideas and information.
 Ability to read, understand and interpret engineering drawings.
UNIT – I
Introduction To Engineering Drawing: Principles of Engineering Graphics and their
Significance, Conic Sections. Involute, Cycloid, Epicycloid and Hypocycloid Scales – Plain &
Diagonal.
UNIT - II
Orthographic Projections: Principles of Orthographic Projections – Conventions –
Projections of Points and Straight Lines. Projections of Plane regular geometric figures.—
Auxiliary Planes.
UNIT – III
Projections of Regular Solids – Auxiliary Views.
UNIT – IV
Sectionsand Developments: Sectional views of Right Regular Solids – Prism, Cylinder,
Pyramid, Cone – Auxiliary views. Development of Surfaces of Right Regular Solids – Prism,
Cylinder, Pyramid, and Cone.
UNIT – V
Isometric &OrthographicProjections: Principles of Isometric Projection – Isometric Scale –
Isometric Views – Conventions – Isometric Views of Lines, Plane Figures, Simple Solids –
Conversion of Isometric Views to Orthographic Views.
Text Books:
1. Engineering Drawing N.D. Bhatt / Charotar
2. Engineering Drawing / BasantAgrawal and McAgrawal/ McGraw Hill
3. Engineering Drawing/ M.B. Shah, B.C. Rane / Pearson.
4. Engineering Drawing / N.S. Parthasarathy and Vela Murali/ Oxford

CIS SHEET
PROBABILITY THEORY AND STOCHASTIC PROCESSES
PROGRAMME: B TECH DEGREE: B TECH
COURSE:ENGINEERING GRAPHICS SEMESTER: I-I,I-II CREDITS: 4
COURSE CODE: ME106ES/ME205ES COURSE TYPE: CORE /ELECTIVE /
REGULATION: R17 BREADTH/ S&H
COURSE AREA/DOMAIN: DESIGN CONTACT HOURS: 2L+4D hours/Week.
CORRESPONDING LAB COURSE CODE (IF ANY): -- LAB COURSE NAME: --
UNIVERSITY SYLLABUS:
UNIT DETAILS HOURS
INTRODUCTION TO ENGINEERING DRAWING: Principles of Engineering
Drawing/Graphics - Various Drawing Instruments - Conventions in Drawing - Lettering
practice - BIS Conventions.
Curves: Constructions of Curves used in Engineering Practice:
I 12
a) Conic Sections including the Rectangular Hyperbola - General method only.
b) Cycloid, Epicycloids and Hypocycloid
c) Involutes.
Scales: Construction of different types of Scales, Plain, diagonal.
ORTHOGRAPHIC PROJECTIONS IN FIRST ANGLE
• PROJECTION: Principles of Orthographic Projections - Conventions - First and
Third Angle projections. Projections of Points. Including Points in all four quadrants.
II • Projections of Lines - Parallel, perpendicular inclined to one plan and inclined to 14
both planes. True length and true angle of a line. Traces of a line.
• PROJECTIONS OF PLANES: Plane parallel, perpendicular and inclined to one
reference plane. Plane inclined to both the reference planes
PROJECTIONS OF SOLIDS: Projections of regular solids, cube, prisms, pyramids,
III 12
tetrahedron, cylinder and cone, axis inclined to both planes
SECTIONS AND SECTIONAL VIEWS: Right Regular Solids - Prism, Cylinder, Pyramid,
Cone - use of Auxiliary views
IV 14
DEVELOPMENT OF SURFACES: Development of Surfaces of Right, Regular Solids -
Prisms, Cylinder, Pyramids, Cone and their parts. Frustum of Solids.
ISOMETRIC PROJECTIONS : Principles of Isometric Projection - Isometric Scale -
Isometric Views- Conventions - Plane Figures, Simple and Compound Solids - Isometric
Projection of objects having non- isometric lines. Isometric
V 12
Projection of parts with Spherical surface
TRANSFORMATION OF PROJECTIONS: Conversion of Isometric Views to
Orthographic Views. Conversion of orthographic views to isometric views - simple objects.
TOTAL HOURS 64
GAPS IN THE SYLLABUS - TO MEET INDUSTRY/PROFESSION REQUIREMENTS:

PROPOSED
SNO DESCRIPTION PO
ACTIONS
P116.1,
Intersections(C116.5)
1 PPT,VIDEOS P116.3,
P116.5
P116.1,
Perspectives(C116.6)
2 PPT,VIDEOS P116.3,
P116.5
PROPOSED ACTIONS: TOPICS BEYOND SYLLABUS/ASSIGNMENT/INDUSTRY VISIT/GUEST LECTURER/NPTEL ETC

TOPICS BEYOND SYLLABUS/ADVANCED TOPICS/DESIGN:
SNO DESCRIPTION CO PO
P116.1,
C116.5
1 Intersections P116.3,
P116.5
P116.1,
C116.6
2 Perspectives P116.3,
P116.5
DELIVERY/INSTRUCTIONAL METHODOLOGIES:
CHALK & TALK STUD. ASSIGNMENT WEB RESOURCES PPT’S
LCD/SMART BOARDS STUD. SEMINARS ADD-ON COURSES VIDEOS
ASSESSMENT METHODOLOGIES-DIRECT
TESTS/MODEL
ASSIGNMENTS STUD. SEMINARS UNIV. EXAMINATION
EXAMS
STUD. LAB MINI/MAJOR
STUD. VIVA CERTIFICATIONS
PRACTICES PROJECTS
ADD-ON COURSES OTHERS
ASSESSMENT METHODOLOGIES-INDIRECT
ASSESSMENT OF COURSE OUTCOMES (BY STUDENT FEEDBACK ON FACULTY
FEEDBACK, ONCE) (TWICE)
ASSESSMENT OF MINI/MAJOR PROJECTS BY EXT. OTHERS
EXPERTS
WEB SOURCE REFERENCES:

1 www.mpcfaculty.net/Steven_Pearce/ENGR2/04ES301Lecture01.ppt
2 www.iitg.ernet.in/rkbc/ME111/Lecture1%20Introduction.pdf
3 ece.gmu.edu/~clorie/Fall10/ENGR-107/Lectures/Lecture_2.ppt
4 www.scribd.com/doc/.../Lecture-1-Fundamentals-of-Engineering-Drawin...
5 www.up.edu.ps/ocw/repositories/pdf-archive/L13_Missing_view.pdf
6 https://www.youtube.com/user/rajaroym/videos
TEXT/REFERENCE BOOKS:
T/R BOOK TITLE/AUTHORS/PUBLICATION

1. Engineering Drawing, N.D. Bhatt.(T1)
2. Engineering Drawing - Basant, Agrawal, TMH (T2)
3. Engineering Graphics. P I Varghese Tata McGraw Hill Education Pvt. Ltd.(R1)
4. Engineering drawing - P.J. Shah .S.Chand Publishers. (R2)
5. Engineering Drawing- Johle/Tata Macgraw Hill Book Publishers. (R3)
6. Engineering Drawing - M.B. Shah and B.C. Rana, Pearson. (R4)
7. Engineering Drawing by K.Venu Gopal&V.Prabu Raja New Age Publications. (R5)
8. Engineering Drawing By John. PHI Learning Publisher(R6)

COLLEGE SYLLABUS(Including beyond the Syllabus)
UNIT - I
INTRODUCTION TO ENGINEERING DRAWING: Principles of Engineering Drawing/Graphics
- Various Drawing Instruments - Conventions in Drawing - Lettering practice - BIS Conventions.
Curves: Constructions of Curves used in Engineering Practice:
a) Conic Sections including the Rectangular Hyperbola - General method only.
b) Cycloid, Epicycloids and Hypocycloid
c) Involutes.
Scales: Construction of different types of Scales, Plain, diagonal,.
UNIT - II
ORTHOGRAPHIC PROJECTIONS IN FIRST ANGLE
• PROJECTION: Principles of Orthographic Projections - Conventions - First and Third Angle
projections. Projections of Points. Including Points in all four quadrants.
• Projections of Lines - Parallel, perpendicular inclined to one plan and inclined to both planes.
True length and true angle of a line. Traces of a line.
• PROJECTIONS OF PLANES: Plane parallel, perpendicular and inclined to one reference
plane. Plane inclined to both the reference planes
UNIT-III
• PROJECTIONS OF SOLIDS: Projections of regular solids, cube, prisms, pyramids,
tetrahedron, cylinder and cone, axis inclined to both planes
UNIT-IV
• SECTIONS AND SECTIONAL VIEWS: Right Regular Solids - Prism, Cylinder, Pyramid,
Cone - use of Auxiliary views
• DEVELOPMENT OF SURFACES: Development of Surfaces of Right, Regular Solids -
Prisms, Cylinder, Pyramids, Cone and their parts. Frustum of Solids.
• INTERSECTION OF SOLIDS
UNIT-V
• ISOMETRIC PROJECTIONS : Principles of Isometric Projection - Isometric Scale -
Isometric Views- Conventions - Plane Figures, Simple and Compound Solids - Isometric
Projection of objects having non- isometric lines. Isometric
Projection of parts with Spherical surface
• TRANSFORMATION OF PROJECTIONS: Conversion of Isometric Views to
Orthographic Views. Conversion of orthographic views to isometric views - simple objects.
• PERSPECTIVES
Note : Engineering Drawing has 4 credits

SUGGESTED BOOKS
TEXT BOOKS:
1.Engineering Drawing, N.D. Bhatt(T1)
2.Engineering Drawing - Basant, Agrawal, TMH (T2)
REFERENCE BOOKS:
1.Engineering Graphics. P I Varghese Tata McGraw Hill Education Pvt. Ltd.(R1)

2. Engineering drawing - P.J. Shah .S.Chand Publishers. (R2)
3. Engineering Drawing- Johle/Tata Macgraw Hill Book Publishers. (R3)
4. Engineering Drawing - M.B. Shah and B.C. Rana, Pearson. (R4)
5.Engineering Drawing by K.Venu Gopal&V.Prabu Raja New Age Publications.
(R5)
6. Engineering Drawing By John. PHI Learning Publisher(R6)
SUGGESTED WEBSITES:
Links with Direct Url
 www.mpcfaculty.net/Steven_Pearce/ENGR2/04ES301Lecture01.ppt
 www.iitg.ernet.in/rkbc/ME111/Lecture1%20Introduction.pdf
 ece.gmu.edu/~clorie/Fall10/ENGR-107/Lectures/Lecture_2.ppt
 www.scribd.com/doc/.../Lecture-1-Fundamentals-of-Engineering-Drawin...
 www.up.edu.ps/ocw/repositories/pdf-archive/L13_Missing_view.pdf
 https://www.youtube.com/user/rajaroym/videos

Course Name:Engineering Graphcs YEAR: 2017-18
COURSE OUTCOMES: ENGINEERING GRAPHICS (C116)
Students able to construct engineering curves of conics sections, cycloid
C116.1
curves, involutes and scales.
Students able to draw projections of points, straight lines & planes inclined to
C116.2
one or both the projection planes.
Students able to draw projections of solids and sectional solids inclined to one
C116.3
or both the projection planes.
Students able to develop the lateral surfaces for cone, cylinder, prisms and
C116.4
pyramid projections.
Students able to draw views of an object (F.V, T.V & S.V) and convert the
C116.5 isometric views to orthographic views, vice-versa. Perspectives.either by CAD
softwares or by Hand drawings.
Students able to prepare the orthographic views of Intersection of solids like
C116.6
cone, cylinder, prisms and pyramid projections.
Course Relationship of Course outcomes(CO) to Program Outcomes (PO)

Outcomes
P116.10
P116.11
P116.12
P116.1
P116.2
P116.3
P116.4
P116.5
P116.6
P116.7
P116.8
P116.9
PSO1
PSO2
CO/PO
C116.1 3 3 2
C116.2 3 3 2
C116.3 3 3 2
C116.4 3 3 2
C116.5 3 3 2
C116.6 3 3 2
NOTE: 3- HIGH, 2-MEDIUM, 1-LOW
1. Engineering knowledge
2. Problem analysis
3. Design/development of solutions
4. Conduct investigations of complex problems
5. Modern tool usage
6. The engineer and society
7. Environment and sustainability
8. Ethics
9. Individual and team work
10. Communication
11. Project management and finance
12. Life-long learning

CO-PO mapping Justification
C116.1 : INTRODUCTION TO ENGINEERING
DRAWING,CONICS,CURVES,INVOLUTES,SCALES
Justification
Student get the knowledge of using different Engineering instruments,rules to follow
P116.1
during drawing of a given object or any specified object.
Student will identify the given object, based on that if any formulations are needed using
P116.3 first principles of mathematics the solution for the given design drawing can be made.
Student will be understanding the modern tools in the form of softwares and how easy to
P116.5
understood machine and machine components working.
C116.2:ORTHOGRPHIC PROJECTIONS,PROJECTION OF POINTS,LINES,PLANES
Justification
Student get the knowledge of viewing of an object in different positions,rules to follow
P116.1
during drawing of a given isometric object into orthographic object.
P116.3 first principles of mathematics the solution for the given design drawing can be made.
P116.5 understood the given object in the form of first angle and third angle projections and their
importance.
C116.3 :PROJECTION OF SOLIDS

Justification
Student get the knowledge of viewing of an solid object in different positions,rules to
P116.1
follow during drawing of a given solid object.
P116.3
first principles of mathematics the solution for the given design drawing can be made.
P116.5
understood the given object in the form of first angle for a given solid.
C116.4: SECTION OF SOLIDS,DEVELOPMENT OF SURFACES

Justification
Student get the knowledge of viewing of an sectional sold object and development of a
P116.1 solid and a sectional solid in different positions,rules to follow during drawing of a given
solid and sectional solid object.
P116.3
first principles of mathematics the solution for the given design drawing can be made.
P116.5
understood the given object in the form of first angle for a given solid and sectional solid.

C116.5 : Intersections
Justification
Student get the knowledge of viewing of an intersected solid object in different
P116.1
positions,rules to follow during drawing of a given solid and intersected solid object.
Student will identify the given object, based on that if any formulations are needed using first
P116.3
principles of mathematics the solution for the given design drawing can be made.
conversion to isometric object.
C116.6: Transformations and Perspectives

Justification
Student get the knowledge of viewing of an object in different positions,rules to follow during
P116.1
drawing of a given orthographic object into isometric object.
Student will identify the given object, based on that if any formulations are needed using first
P116.3
principles of mathematics the solution for the given design drawing can be made.
conversion to isometric object.

ACADEMIC CALENDAR:

TIME TABLES
DEPARTMENTAL TIME TABLES(H&S)
St. PETER’S ENGINEERING COLLEGE

DEPARTMENT OF SCIENCE AND HUMANITIES
CLASS TIMETABLE
Department/Program: MEC A/BTECH Class/Semester: I/I
Room No.: T3 Academic Year: 2017-18 Tutorial Room: T3
Date (W.E.F): 31/07/2017

1 2 3 4 5 6 7 8
DAY/
9:00 9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30
HOURS
9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30 4:20
MON EG EP EM M1 EM M2 EP
TUE M2 EG M1 EM SPORTS
WED CP EP M1 M2 LIB CP EM M1
BREAK
THU EM M2 CP EP NSS CDS LAB
FRI CP EP CP M1 M2 EP LAB
SAT EM LIBRARY SPORTS EG M1 CP M2
Subject Code Subject Faculty Contact No.

MA101BS M1 MATHEMATICS -1 P.RAMESHWARI 8106262795
MA102BS M2 MATHEMATICS -2 M.S .KIRANMAI 9704944433
PH103BS EP ENGINEERING PHYSICS T.R.P.MUKHARJI 9642173561
CS104ES CP COMPUTER PROGRAMMING IN C KISHORE REDDY 9703062534
ME105ES EM ENGINEERING MECHANICS RAGHU KUMAR REDDY 9704885854
ME106ES EG ENGINEERING GRAPHICS JABIULLA 9949128690

T.R.P.MUKHARJI/
PH107BS EP LAB ENGINEERING PHYSICS LAB 9642173561
SPANDANA
CS108ES CP LAB COMPUTER PROGRAMMING IN C LAB KISHORE REDDY 9703062534
Activity Faculty Contact No.
NSS RAGHU KUMAR REDDY 9704885854
SPORTS M.S .KIRANMAI 9704944433
LIBRARY T.R.P.MUKHARJI 9642173561
P.RAMESHWARI 8106262795
Mentors / Counselors (M/C)
JABIULLA 9949128690
Tutorial classes*
Note:-Tutorial will be taken up by the concern faculty.
Timetable In-charge HOD Timetable Co-Ordinator PRINCIPAL

DEPARTMENTAL TIME TABLE(H&S)

CLASS TIMETABLE
Department/Program: MEC B/BTECH Class/Semester: I/I
Date (W.E.F): 31/07/2017

1 2 3 4 5 6 7 8
DAY/
9:00 9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30
HOURS
9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30 4:20
MON M1 EM CP M2 NSS CDS LAB
TUE EM M1 EM EP M2 CP CP M1
WED EG M2 M2 EP EM
BREAK
THU EG EP M1 SPORTS EP LAB
FRI M2 SPORTS LIB EG M1 CP EM
SAT CP M2 CP EP EP EM M1 LIB

MA101BS M1 MATHEMATICS -1 P.AMALESWARI 7396032822
MA102BS M2 MATHEMATICS -2 M.S .KIRANMAI 9014281773
PH103BS EP ENGINEERING PHYSICS T.R.P.MUKHARJI 9642173561
CS104ES CP COMPUTER PROGRAMMING IN C KISHORE REDDY 9703062534
ME105ES EM ENGINEERING MECHANICS RAGHU KUMAR REDDY 9704885854
K.SPANDANA/
PH107BS EP LAB ENGINEERING PHYSICS LAB 8332015101
BHARADWAJ
CS108ES CP LAB COMPUTER PROGRAMMING IN C LAB KISHORE REDDY 9703062534
NSS KISHORE REDDY 9703062534
SPORTS RAGHU KUMAR REDDY 9704885854
LIBRARY T.R.P.MUKHARJI 9642173561
T.R.P.MUKHARJII 9642173561
Mentors / Counselors (M/C)
RAGHU KUMAR REDDY 9704885854
Tutorial classes*

INDIVIDUAL TIME TABLE(H&S)
TIME TABLE:
FACULTY NAME: JABIULLA SECTION:MECH A ,MECH B YEAR/SEM: I-I
1 2 3 4 5 LUNCH 6 7 8
DAY/
HOURS
9:00 9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30
9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30 4:20
MON MECH A(L)
TUE MECH A(D)
WED MECH B(D)
THU MECH B(L)
FRI MECH B(T)
SAT MECH A(T)


CLASS TIMETABLE
Department/Program: ECE A/BTECH Class/Semester: I/II
Date (W.E.F): 18/12/2017

1 2 3 4 5 6 7 8
9:00 9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30
Day/HOURS 9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30 4:20
MON EP M3 M2 CP M3 EC LAB
TUE EG LIB M2 EP M3*
WED M2 CP EG* SPORTS M3 M2* CP
BREAK
THU M3 CP M2 EP LIB SPORTS EG
FRI CP M3 EP LAB M2 CP* DAAC
SAT CP M3 EP M2 DAAC CP LAB

PH201BS EP ENGINEERING PHYSICS-II BHARADWAJ M 9441239423
MA202BS M2 MATHEMATICS -II B VENKATARATNAM 9492531983
MA203BS M3 MATHEMATICS -III Dr R P SREEDEVI 8688102365
CS204ES CP COMPUTER PROGRAMMING IN C HIMA BINDHU 9491161282
CH206BS EC LAB ENGINEERING CHEMISTRY LAB Dr RAMBABU/MOUNIKA 9966031325
PH207BS EP LAB ENGINEERING PHYSICS LAB BHARADWAJ M 9441239423
CS208ES CP LAB COMPUTER PROGRAMMING IN C LAB HIMA BINDHU/ LAVANYA 9491161282

SPORTS B VENKATARATNAM 9492531983
LIBRARY BHARADWAJ M 9441239423
DAAC SINDHU M 9676045466
Mentors / Counselors (M/C) BHARADWAJ M 9441239423
MOUNIKA A 8106698028
Tutorial classes*


CLASS TIMETABLE
Department/Program: :CSE C/BTECH Class/Semester: I/II
Room No:T7 Academic Year: 2017-18 Tutorial Room: T7
Date (W.E.F): 18/12/2017

1 2 3 4 5 6 7 8
9:00 9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30
Day/HOURS 9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30 4:20
MON CP EP EC LAB M2 EP DAAC
TUE EP M2 CP M2 M3 CP* M3 SPORTS
WED M3 CP EP LAB
BREAK
M2 M3 M2*
THU EG* CP LAB M3 CP LIB
FRI M2 EG DAAC M3* EP
SAT CP CP M3 M2 SPORTS LIB EG

PH201BS EP ENGINEERING PHYSICS-II BHARADWAJ M 9441239423
MA202BS M2 MATHEMATICS -II M K VASUMATHY 9000548183
MA203BS M3 MATHEMATICS -III S SATHISH 9985560493
CS204ES CP COMPUTER PROGRAMMING IN C LAXMI NARAYANA 9989978779
EC S REVATHI/M
CH206BS ENGINEERING CHEMISTRY LAB
LAB HINUJA 9553236254
EP
PH207BS ENGINEERING PHYSICS LAB
LAB BHARADWAJ M 9441239423
CP LAXMI NARAYANA/
CS208ES COMPUTER PROGRAMMING IN C LAB 9989978779
LAB FLORA

SPORTS BHARADWAJ M 9441239423
LIBRARY LAXMI NARAYANA 9989978779
DAAC RICHE PANDEY 7730050729
Mentors / Counselors S REVATHI 9553236254
(M/C) JABIULLA 9949128690
Tutorial classes*
TimetableCo-
Timetable In-charge HOD PRINCIPAL
Ordinator

INDIVIDUAL TIME TABLE
FACULTY NAME : JABIULLA SECTION: ECE A,CSE C YEAR/SEM:I-II
1 2 3 4 5 6 7 8
DAY/
HOURS
9:00 9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30
9:50 10:40 11:30 12:20 1:10 1:50 2:40 3:30 4:20
MON
TUE ECE A(D)
LUNCH
WED ECE A(L)
THU CSE C (L) ECE A(T)
FRI CSE C(D)
SAT CSE C(T)

LESSON PLAN
Type of
Practice
Lecture
Topic(JNTU No.of Lectures Suggested
S.no Sub-Topic (L),
Syllabus) Required Books
Drawing
Practice
(D)
Principles of
Engineering
Drawing/Gra
phics N.D. Bhatt(T1)
Various Basant
Drawing Agrawal(T2)
2 L1,L2
Instruments
Conventions
in Drawing
Lettering N.D. Bhatt(T1)
practice -
BIS
Basant
Conventions. Agrawal(T2)
Curves:
Construction N.D. Bhatt(T1)
s of Curves
used in
2 Basant L3,L4
UNIT-I Agrawal(T2)
Engineering
INTRODUCTIO Practice
1 Conic
N TO
ENGINEERING Sections
DRAWING including the N.D. Bhatt(T1)
Rectangular 2 Basant L5,L6
Hyperbola Agrawal(T2)
General
method only
Cycloid, N.D. Bhatt(T1)
Epicycloids
and
Basant
Hypocycloid 3 Agrawal(T2) L7,D1,D2
N.D. Bhatt(T1)
Involutes Basant
Agrawal(T2)
Scales:
Construction N.D. Bhatt(T1)
L8,D3,D4
of different 3 Basant
types of Agrawal(T2)
Scales, Plain,

diagonal
Projections:
Principles of
Orthographic
Projections
Conventions
First and N.D. Bhatt(T1)
Third Angle L9,L10,D5,D
projections
4 Basant 6
Projections Agrawal(T2)
of Points.
Including
Points in all
four
quadrants.
Projections
of Lines -
Parallel
Perpendicula
r to one
plane
UNIT-II
Inclined to N.D. Bhatt(T1)
one plane L11,L12,D7,
ORTHOGRAPHI
and
4 Basant D8
2 C Agrawal(T2)
Inclined to
PROJECTIONS
both planes
IN FIRST
True length
ANGLE
and true
angle of a
line.
Traces of a
line.
Projection
of Planes:
Plane
parallel to
one Plane
Plane
Perpendicula N.D. Bhatt(T1)
r to one L13,L14,L15,
Plane
6 Basant D9,D10,D11
Plane Agrawal(T2)
inclined to to
one Plane
Plane
inclined to
both the
reference
planes
Projections
of regular
solids
Cube
L16,L17,L18,
Prisms N.D. Bhatt(T1)
UNIT-III L19,L20,L21,
Pyramids
3 PROJECTIONS
Tetrahedron
12 Basant D12,D13,D1
OF SOLIDS Agrawal(T2) 4,D15,D16,D
Cylinder 17
Cone
Axis inclined
to both
planes
Right Regular
Solids
Prism N.D. Bhatt(T1) L22,L23,L24,
Cylinder L25,
Pyramid
8 Basant D18,D19,D2
Cone - use of Agrawal(T2) 0,D21
Auxiliary
UNIT-IV views
SECTIONS AND Development
SECTIONAL of Surfaces
4 VIEWS of Right,
DEVELOPMEN Regular
T OF Solids
SURFACES N.D. Bhatt(T1) L26,L27,L28
Prisms
Cylinder
6 Basant D22,D23,D2
Agrawal(T2) 4
Pyramids
Cone and
their parts
Frustum of
Solids.
Principles of
Isometric
Projection
Isometric
UNIT-V Scale
ISOMETRIC Isometric N.D. Bhatt(T1) L29,L30,L31,
PROJECTIONS Views
5
Conventions
6 Basant D25,D26,D2
TRANSFORMA 7
TION OF Plane Figures Agrawal(T2)
PROJECTIONS Simple and
Compound
Solids
Isometric
Projection of

objects having
non- isometric
lines
Isometric
Projection
of parts with
Spherical
surface
Conversion of
Isometric
Views to
Orthographic
Views N.D. Bhatt(T1) L32,L33,L34,
Conversion of 6 Basant D28,D29,D3
orthographic Agrawal(T2) 0
views to
isometric
views - simple
objects.
3 N.D. Bhatt(T1) L35,L36,L37
Revision of ,L38,L39,D3
REVISION
Syllabus
3 Basant
1,D32,D33,D
3 Agrawal(T2) 34
39(L)+34(D)
Total Classes Required 73 Total(L+D)
=73

GAPS IN THE SYLLABUS - TO MEET INDUSTRY/PROFESSION REQUIREMENTS:
PROPOSED
SNO DESCRIPTION PO
ACTIONS
P116.1,
Intersections(C116.5) PPT,VIDEOS P116.3,
1
P116.5
P116.1,
Perspectives(C116.6) PPT,VIDEOS P116.3,
2
P116.5
PROPOSED ACTIONS: TOPICS BEYOND SYLLABUS/ASSIGNMENT/INDUSTRY VISIT/GUEST LECTURER/NPTEL ETC
TOPICS BEYOND SYLLABUS/ADVANCED TOPICS/DESIGN:

SNO DESCRIPTION CO PO
P116.1,
Intersections C116.5 P116.3,
1
P116.5
P116.1,
Perspectives C116.6 P116.3,
2
P116.5
DELIVERY/INSTRUCTIONAL METHODOLOGIES:
STUD.
CHALK & TALK WEB RESOURCES PPT’S
ASSIGNMENT
LCD/SMART
STUD. SEMINARS ADD-ON COURSES VIDEOS
BOARDS
ASSESSMENT METHODOLOGIES-DIRECT
TESTS/MODEL UNIV.
ASSIGNMENTS STUD. SEMINARS
EXAMS EXAMINATION
STUD. LAB MINI/MAJOR
STUD. VIVA CERTIFICATIONS
PRACTICES PROJECTS
ADD-ON COURSES OTHERS
ASSESSMENT METHODOLOGIES-INDIRECT
ASSESSMENT OF COURSE OUTCOMES STUDENT FEEDBACK ON
(BY FEEDBACK, ONCE) FACULTY (TWICE)
ASSESSMENT OF MINI/MAJOR PROJECTS OTHERS
BY EXT. EXPERTS

WEB SOURCE REFERENCES:
1 www.mpcfaculty.net/Steven_Pearce/ENGR2/04ES301Lecture01.ppt
2 www.iitg.ernet.in/rkbc/ME111/Lecture1%20Introduction.pdf
3 ece.gmu.edu/~clorie/Fall10/ENGR-107/Lectures/Lecture_2.ppt
4 www.scribd.com/doc/.../Lecture-1-Fundamentals-of-Engineering-Drawin...
5 www.up.edu.ps/ocw/repositories/pdf-archive/L13_Missing_view.pdf
6 https://www.youtube.com/user/rajaroym/videos

UNIVERSITY QUESTION PAPER

INTERNAL QUESTION PAPER(MID-I)

I-B.Tech I Sem - I Mid Examinations SET-01
Year: I Branch:MEC (S&H)
Subject: EG Duration: 2Hr Date:

Answer any TWO from the following Questions Marks 2x5M=10M
Note:- All Questions are mapped with Blooms Taxonomy Levels and Course Outcomes
S.No. Questions Skill CO
A)Draw an ellipse when the distance of its focus from its directrix is 40mm and
eccentricity is 2/3. Also draw a tangent and normal to the ellipse at a point 70mmaway Application C116.1
from the directrix.(2.5M)
1
B) Draw a hypocycloid of a circle dia 40mm , which rolls inside the circle for dia 100mm
for the one revolution also , draw a tangent and normal to the hypocycloid at a point Knowledge C116.1
65mm from the centre of directing circle(2.5M)
A) Draw a involute of a circle of dia 50mm(2.5M) Application C116.1
2
B)Construct an ellipse having a major axis 100mm and minor axis 80mm . locate its foci, Analysis C116.1
directrix and find the eccentricity.(2.5M)
A) Draw a parabola when the distance between foci and directrix is 50mm .Also draw at Knowledge C116.1
3 tangent and normal at a point of 40mm from directrix. (2.5M)
B)Inscribe a parabola in a rectangle of sides 70mm and 30mm with the longer side as the Analysis C116.1
base. locate the focus and directrix of the parabola. (2.5M)
A) Draw an hyperbola when the distance of its focus from its directrix is 50mm and
eccentricity is 3/2. Also draw a tangent and normal to the hyperbola at a point 40 mm Knowledge C116.2
4 away from the directrix. (2.5M)
B) Two fixed points are 80mm apart. Draw the locus of a point P which moves in a such a
way that the difference of its distance from the fixed points is always the same and equal Knowledge C116.1
to 60mm . (2.5M)

SCHEME OF EVALUATION
I-B.Tech I Sem - I Mid Examinations SET-01
S. No THEORY MARKS TOTAL
Drawing of ellipse(General Method) with
proper drawing instruments clearly and 2
A)
accurately
Proper Margins,Title block Filling
0.5
Dimensioning and lettering 5
1
Drawing of Hypocycloid with proper
2
drawing instruments clearly and accurately
B)
0.5
Dimensioning and lettering
Drawing of involute with proper drawing
2
instruments clearly and accurately
A)
0.5
2
Drawing of ellipse(Rectangle Method) with 5
B) accurately
0.5
Drawing of parabola (General Method) with
A)
accurately
0.5
3 5
Drawing of parabola (Rectangle Method)
with proper drawing instruments clearly and 2
B) accurately
0.5
A) Drawing of Hyperbola (General Method)
with proper drawing instruments clearly and 2
accurately
0.5
4 Dimensioning and lettering 5
B) Drawing of Hyperbola with proper drawing
2
0.5
TOTAL 10

INTERNAL QUESTION PAPER KEY(MID-I)
1)a 2)a
1)b 2)b

3)a 4)a
4)b
3)b

INTERNAL QUESTION PAPER(MID-II)

I-B.Tech I Sem - II Mid Examinations SET-01
Year: I
Branch:MEC(S&H)
A) A pentagonal prism of base side 30mm and axis 60mm is resting on one of its Knowledge C116.2
rectangular faces on the HP with axis parallel to the VP.Draw its Projections.(2.5M)
1 B)A hexagonal pyramid of side of base 30 mm and axis length 90 mm rests on one of its
slant edge on the H.P. such that the plane containing that slant edge on which it rests on Knowledge C116.3
H.P. is inclined at 45° to V.P. and the apex is near to the V.P. Draw the projection of it.
(2.5M)
A)A square hole of side 25mm is cut in a cylindrical drum of diameter 50mm and height
70mm.The faces of the hole are inclined at 45° to the HP and axis intersects with that of Application C116.2
2 the drum at right angles.Draw the development of its lateral surface (2.5M)
B)A hexagonal plane of side 30mm has an edge on the HP.Its surface is inclined at 45°
to the HP and the edge on which the plane rests is inclined at 30° to the VP.Draw its Analysis C116.2
Projections.(2.5M)
A) A pentagonal prism of base side 30mm and axis 70mm has an edge of its base on the
HP.The axis is parallel to the VP and inclined at 60° to the HP.It is cut by an A.I.P Analysis C116.4
inclined at 60° to the HP and passing through the highest corner of the prism. Draw its
3 sectional top view an true shape of the section (2.5M)
B)Draw the projections of a cylinder of base diameter 50 mm length of axis is 70mm is
resting on a point of the base in the HP with the axis is inclined at 30 0 to HP and top Analysis C116.3
view of axis is perpendicular to VP. (2.5M)
A) A pentagonal pyramid of base side 30mm and axis 60mm is resting on its base in the
HP with an edge parallel to the VP.A horizontal section plane cuts the pyramid bisecting Knowledge C116.4
the axis.Draw its front view and sectional top view. (2.5M)
B)Transform Isometric view to orthographic
projection(2.5M)
4
Analysis C116.6

I-B.Tech I Sem - II Mid Examinations SET-01
S. No THEORY MARKS TOTAL
Drawing a pentagonal prism as per the required

data mentioned with proper drawing instruments 2
A)
clearly and accurately
Proper Margins,Title block Filling Dimensioning
0.5
and lettering
5
1 Drawing a Hexagonal pyramid as per the
required data mentioned with proper drawing 2
B) instruments clearly and accurately
0.5
and lettering
Drawing a Cylindrical drum with Square hole as
per the required data mentioned with proper 2
A) drawing instruments clearly and accurately
0.5
2 and lettering
5
Drawing a Hexagonal plane as per the required
B) clearly and accurately
0.5
and lettering
Drawing a Pentagonal prism as per the required
A)
clearly and accurately
0.5
and lettering
3 5
Drawing the projections of cylinder as per the
B) instruments clearly and accurately
0.5
and lettering
A) Drawing the pentagonal pyramid as per the
0.5
and lettering
4 B) Transform the Isometric view to orthographic 5
view as per the required data mentioned with
2
proper drawing instruments clearly and
accurately
0.5
and lettering
TOTAL 10

INTERNAL QUESTION PAPER KEY(MID-II)
1)a 2)b
1)b 3)a
2)a 3)b

4)a
4) b

I-B.Tech I Sem - I Mid Assignment
Year: I Branch: MECH (S&H)
Subject: EG
Answer All from the following Questions Marks 10x1.5M=15M
a) a)Draw an ellipse when the distance of its focus from its directrix is 55mm and
eccentricity is 2/3. Also draw a tangent and normal to the ellipse at a point 70mmaway Application C116.1
from the directrix.(1.5M)
1
b) Draw a hypocycloid of a circle dia 50mm , which rolls inside the circle for dia 180mm
for the one revolution also , draw a tangent and normal to the hypocycloid at a point Knowledge C116.1
65mm from the centre of directing circle.(1.5M)
a)Draw a epicycloid of a circle dia 50mm , which rolls inside the circle for dia 180mm
for the one revolution also , draw a tangent and normal to the epicycloid at a point Application C116.1
2
80mm from the centre of directing circle. .(1.5M)
b)Construct an ellipse having a major axis 100mm and minor axis 65mm using concentric Analysis C116.1
circle method.(1.5M)
a) The distance between two stations by road is 200Km and it is represented on a map by
a 5cm long line .Find the RF and construct diagonal scale showing a single kilometer and Knowledge C116.1
3
long enough to measure upto 600km.Show a distance of 467 Kms on this scale(1.5M)
b)Inscribe a parabola in a rectangle of sides 100mm and 80mm with the longer side as the Analysis C116.1
base. locate the focus and directrix of the parabola. (1.5M)
a) A line AB of length 80mm with one end 20mm above HP and 30mm infront of
VP.The other end of the line is 80mm above HP and 70 mm infront of VP.The distance Knowledge C116.2
4 between the projectors is 60mm.Draw its projections and determine the values (1.5M)
b)Two fixed points are 80mm apart. Draw the locus of a point P which moves in a such a
way that the difference of its distance from the fixed points is always the same and equal Knowledge C116.1
to 60mm . (1.5M)
a) (a). Draw the projections of the following points on the same reference line(xy
line),keeping the projectors 25mm apart (1.5M)
A. in the H.P. and 25 mm behind the V.P.
B. 40 mm above the H.P. and 25 mm in front of the V.P.
C. is in the V.P. and 40 mm above the H.P. Analysis C116.2
5 D. 25 mm below the H.P. and 25 mm behind the V.P.
E. 15 mm above the H.P. and 50 mm behind the V.P.
F. 40 mm below the H.P. and 25 mm in front of the V.P.
G. in both the H.P. and the V.P.
b) a) The front view of a line, inclined at 300 to the V.P. is 65 mm long. Draw the
projection of the line, when it is parallel to and 40 mm above the HP, its one end being 30 Knowledge C116.1
mm in front of the V.P. (1.5M)

I-B.Tech I Sem - II Mid Assignment
Year: I Branch: MEC (S&H)
Subject: EG
Answer All from the following Questions Marks 10x1.5M=15M
A )Draw the projections a regular hexagon of 25mm side, having one of its sides in the
H.P. and inclined at 600 to the V.P. and its surface makes an angle of 450 with the H.P Application C116.2
1 (1.5M)
B )A square prism side of base 40 mm and axis is 65 mm long has its axis inclined at
450 to HP and has an edge of its base on the HP and inclined at 30 0 to VP. draw the Knowledge C116.2
projections. (1.5M)
A )A line PQ is 80 mm long and the end A is 15 mm above H.P. . The line is inclined at
30° with H.P. and 45° with V.P. Draw the projections of the line when it is in 1st Application C116.2
quadrant. (1.5M)
2 B )A pentagonal prism of side of base is 40 mm and axis height 110 mm rests on one of
its corner of its base on H.P. such that the axis is inclined at an angle of 40° with H.P. Analysis C116.2
and edge of base is 60° with the V.P. Draw its projection
(1.5M).
A )A cone of base 50 mm diameter and axis 65 mm long lies on HP on one of its
generator with its axis parallel to VP , a horizontal section plane bisects the axis of the Knowledge C116.3
3 cone draw the front and sectional top views . (1.5M)
B )A pentagonal pyramid of base side 30mm and 60mm long axis has one of its
triangular faces in the VP and the edge of base contained by the face makes an angle of Analysis C116.3
300 with the HP, draw its projections (1.5M)
A )Asquare pyramid of base side 35 mm and axis height 65mm long the base is
Resting on H.P one of its base edge is parallel is to V.P . its cut by plane perpendiclular Knowledge C116.4
to vp and inclined 45 to HP. and bisecting the axis. Draw its development. (1.5M)
4
Analysis C116.5
.
B)Transform Isometric view to orthographic projection(1.5M)
A )A cylinder of diameter of base 60 mm and axis height 110 mm is resting on its base
on H.P. It is cut by a cutting plane perpendicular to V.P. and inclined at an angle 60° Knowledge C116.4
with the H.P. and passing through the distance of 20 mm from top end of the axis, draw
5 the development of lateral surface of the cylinder. (1.5M)
B )Draw the projections of a cylinder of base diameter 50 mm length of axis is 70mm is
resting on a point of the base in the HP with the axis is inclined at 30 0 to HP and top Analysis C116.3
view of axis inclined at 450 to VP. (1.5M)

TITLE: A circle of 40mm diameter is rolling on another circle of diameter 150mm.Draw and name
the curve, draw tangent and normal to the curve at a point 95mm from the directing circle.
Subtitles: Cycloid (Label Size 5mm)
Tools Used:
1. MINI DRAFTER
2. PENCILS: H,2H & HB
3. ERASER
4. SHARPNER
5. PROTRACTOR
6. COMPASS
7. SET-SQUARE
8. FRENCH CURVES
9. DRAWING CLIPS or TAPE
10. DRAWING SHEETS PREFERABLE A2 SIZE
11. SHEET HOLDER
ROUGH SKETCH
Draw the rough diagram in note book with approximate values so that it will be very easy and time
management process while drawing main diagram on sheet.
Procedure
1. After entering into the hall thoroughly clean the table.

2. Fix the drawing sheet along with a rough paper.
3. Adjust the clips /tape on the sheet and ensure that the sheet should be placed at right bottom
corner.
4. Draw the boarder lines by using HB pencil if it is required.
5. Fill the title block with blue/black ball point pen.
6. Fix drafter at top left corner and check whether scale is parallel in position or not by taking
table or sheet as reference
7. Draw the Guide lines and construction lines with 2H pencils and make it as main diagrams
with H pencil with H pencil, and complete lettering and dimensioning with HB pencil.
8. After completing the drawings just fold-up the sheets in a good manner (Three Fold).

UNITS AND CONVERSIONS:
CONVERSION TABLE 1:
SL NO UNIT CONVERSION
1 1 KILOMETRE 10 HECTOMETRE
2 1 HECTOMETRE 10 DECA METRE
3 1 DECA METRE 10 METRE
4 1 METRE 10 DECIMETRE
5 1 DECIMETRE 10 CENTIMETRE
6 1 CENTIMETRE 10 MILLIMETRE
CONVERSION TABLE 2:
SL NO UNIT CONVERSION
1 1 MILE 8 FURLONGS OR 1.609 KILOMETRE
2 1 FURLONG 220 YARDS
3 1 YARD 3 FEETS
4 1 FEET 12 INCHES
5 1 INCH 2.54 CENTIMETRE

IDENTIFICATION OF INSTRUMENTS:

P

PRACTICE OF SYMBOLS:
TRIANGLE
SQUARE

PENTAGON
HEXAGON
HEPTAGON

OCTAGON
PYRAMIDS AND PRISMS

University Question Bank
Unit-I
Construction of Ellipse
General Method
1)Draw an ellipse when the distance of its focus from its directrix is 50mm and the eccentricity is
2/3.Also draw a normal and tangent to the ellipse at a point 70mm away from the directrix.
Intersecting Arcs Method or Arcs of Circle Method
2)A point moves in a plane in such a way that the sum of its distances from two fixed points
100mm apart .Name and draw the locus of this point.
Concentric Circle Method
3)The major axis of an ellipse is 110mm and minor axis is 70mm long .Draw an ellipse by
concentric circle method.
Rectangle Method
4) Inscribe the largest possible ellipse in a rectangle of sides 160mm and 100mm.
Parallelogram Method
5) The conjugate diameters of an ellipse are 110mm and 80mm and the include angle between
them is 75° .Draw an ellipse by parallelogram method.
Construction of Parabola
General Method
6) Draw a parabola when the distance between its focus and directrix is 50mm.Also draw a tangent
and a normal at a point 70mm from the directrix.
Offset Method
7) A parabolic arch has a span of 160mm and a maximum rise of 100mm .Draw a curve using
offset method .
Tangent Method
8)Draw a parabola of base 150mm and axis 80mm by tangent method.
Rectangle Method/Oblong Method
9)Draw a parabola of base 120mm and axis 80mm by oblong method.
10)Inscribe a parabola in parallelogram of sides 110mm and 80mm,the included angle being
60°.Consider the longer side of the parallelogram as the base of the parabola.

Construction of Hyperbola
General Method
11)Draw a hyperbola when the distance of its focus from its directrix is 50mm and eccentricity is
3/2.Also draw a tangent and a normal to the hyperbola at a point 25mm from the directrix.
Intersecting Arcs Method
12)Two fixed points are 80mm apart.Draw the locus of a point P which moves in such a manner
that the difference of its distance from the fixed points is always the same and equal to
60mm.Name the crve.
Oblong Method
13)Draw a hyperbola when half the transverse axis, double ordinate and abscissa are 50mm
120mm and 40mm long respectively.
Intercept Method
14)Draw a rectangular hyperbola when the position of a point P on the curve is at a distance of
30mm and 50mm from two asymptotes.
Orthogonal Asymptotes Method
15)A point P of the hyperbola at a distance of 35mm and 50mm from the pair of asymptotes.The
asymptotes are perpendicular to each other.Draw a hyperbola using orthogonal asymptotes
method.
Oblique Asymptotes Method
16)Draw a hyperbola when its asymptotes are inclined at 60° to each other and passes through a
point P.The point P is at a diatance of 40mm and 50mm from the asymptotes.
Locating Asymptotes and Directrix
17) Draw two branches of hyperbola having foci 70mm apart and vertices 40mm apart. Locate the
asymptotes and measure the included angle. Also locate the directrix of the hyperbola.
Construction of Cycloids and Involutes

Cycloid
18) Draw a cycloid of a circle of diameter 50mm for one revolution .Also draw a tangent and a
normal to the curve at a point 35mm above the base line.
Epicycloid
19) Draw an epicycloids of rolling circle 40mm diameter, which rolls outside another circle(Base
Circle) of 150mm diameter for one revolution. Draw a tangent & normal at a point 110mm from
center of the directing circle.
Hypocycloid

20)Draw a hypocycloid of a circle of 40mm diameter which rolls inside another circle of 200mm
diameter for one revolution. Draw a tangent and normal at a point of 80mm on the curve
generated.
Involutes
21)Draw the involute of an equilateral triangle of side 25mm.
22)Construct the involute of a pentagon of 22mm side
Unwound
23) A coir is unwound from a drum of 30mm diameter. Draw the locus of the free end of the coir
for unwinding through an angle of 360°.Draw also a normal and tangent at any point on the curve.
Wound
24) An elastic string of length 100mm is wound round a circle of 26mm diameter. Draw the path
traced by the end of the string.
Scales
Plain Scale
25) Construct a scale of 1:40 to read meters and decimeters and long enough to measure up to 6
meters. Mark a distance of 4.7m on it.
26) If 1 centimeter long line on a map represents a real length of 4 meters .Calculate the RF and
draw a plain scale long enough to measure up to 50metres.Show a distance of 44m on it.
27)A real length of 1 decameter is represented by a line of 5cm in a drawing .Find the RF and
construct a plain scale to measure up to 2.5 decameters. Mark a distance of 19m on it.
Diagonal Scale
28) Construct a scale of 1:40 to read meters, decimeters and centimeters and long enough to
measure up to 6m.Mark a distance of 4.76m on it.
29) If 1cm long line on a map represents a real length of 4m.Calculate the RF and draw a diagonal
scale long enough to measure up to 50metres.Show a distance of 44.5m on it.
30) The distance between two stations by road is 200km and it is represented on a certain map by
a 5cm long line. Find the RF and construct a diagonal scale showing single kilometer and long
enough to measure up to 600km.Show a distance of 467 km on this scale.

Unit-II
Introduction to Orthographic Projection
Projection of points
Projection of a point situated in First quadrant
1) A Point A is 20 mm above H.P and 30 mm in front of V.P. Draw the Projections of the point.
Projection of a point situated in Second quadrant
2) A Point B is 20 mm above H.P and 30 mm behind V.P. Draw the Projections of the point.
Projection of a point situated in Third quadrant
3) A Point C is 20 mm below H.P and 30 mm behind V.P. Draw the Projections of the point.
Projection of a point situated in Fourth quadrant
4) A Point D is 20 mm below H.P and 30 mm in front of V.P. Draw the Projections of the point.
Point situated in Both H.P and V.P
5) Draw the projections of a point J, lying on both the H.P and the V.P
Point on H.P and in front of V.P
6) Draw the projections of a point E, lying the H.P and 50 mm in front of V.P
Point above the H.P and on the V.P
7) Draw the projections of a point F, lying 70 mm above H.P and on the V.P
Projections of a point situated in First Quadrant
8) A point A is 20mm above HP,30mm in front of VP and 25 in front of PP. Draw its front view,top
view and left side view of the point
Projection of Straight Lines
1. Line Parallel to Both HP and VP
9) A line CD 30mm long is parallel to both the planes. The line is 40mm above HP and 25mm in front
of VP. Draw its Projections.
2. Line Contained/lying in one Plane & Parallel to other
a) Line Contained in HP and Parallel to VP
10) A line RS 60 mm long lies in HP and 45mm in front of VP. Draw its Projections.
b) Line Contained in VP and Parallel to HP
11) A line PQ 55 mm long lies in VP and 45mm above HP. Draw its Projections.
3. Line Contained/lying in Both HP and VP
12) A line AB 55 mm long is lying on both HP and VP. Draw its Projections.
4. Line perpendicular to one Plane and Parallel to the other
a)Line perpendicular to HP and Parallel to VP
13) A line AB 25 mm long is parallel to VP and perpendicular to HP. Point A is 35mm above HP and
20mm in front of VP. Point B is 10mm above HP. Draw the Projections of the line AB
b)Line perpendicular to VP and Parallel to HP
14) A line AB 25 mm long is perpendicular to VP and parallel to HP. Its end A is 10mm in front of VP
and the line is20mm above HP. Draw the Projections of the line.

5. Line Parallel to one Plane & Inclined to other
a) Line Parallel to VP and inclined to HP
15) A line PQ 40 mm long is parallel to VP and inclined at an angle of 30° to HP. The Lower end P is
15mm above HP and 20mm in front of VP. Draw the projections of the line.
b) Line parallel to HP and inclined to VP
16) Draw the projections of a line EF 40mm long parallel to HP and inclined at 35° to VP. E is 20mm
above HP and 15mm in front of VP.
6. Line contained by one Plane & Inclined to other
a) Line contained by VP and inclined to HP
17) A line AB 50mm long is in VP and inclined at an angle of 35° to HP. The end A is 10mm above
HP. Draw the Projections.
b) Line contained by HP and inclined to VP
18) A line RS measuring 52mm is in HP and inclined at an angle of 45° to VP. The end R is 10mm in
front of VP. Draw the Projections.
Traces
1.Line perpendicular to one Plane and Parallel to the other
19) A 60mm long line PQ has its end P 20mm above HP. The line is perpendicular to the HP and
40mm in front of the VP. Draw its projections and locate the traces.
20)A 60mm long line PQ has its end P 20mm in front of the VP.The line is perpendicular to the VP
and 40 mm above the HP.Draw the projections of the line and determine its traces.
2.Line Parallel to one Plane & Inclined to other
a)Line Parallel to VP and inclined to HP
21)A 80mm long line PQ has end P 20mm above HP and 40mm in front of the VP.The line is inclined
at 30° to the HP and is parallel to the VP. Draw the projections of the line and determine its traces
b)Line parallel to HP and inclined to VP
22)An 80mm long line PQ is inclined at 30° to the VP and is parallel to the HP. The end P of the line
is 20mm above the HP and 40mm in front of the VP. Draw the projections of the line and determine its
traces .
3.Line contained by one Plane & Inclined to other
a)Line contained by VP and inclined to HP
23)Draw the projections of a 70mm long line PQ,situated in the VP and inclined at 30° to the HP. The
end P of the line is 25mm above the HP. Also, determine the traces of the line.
b)Line contained by HP and inclined to VP
24)A 60mm long line PQ lying on the HP is inclined at 30° to the VP. Its end P is 20mm in front of
the VP. Draw the projections of the line and determine its traces .
4.Line Parallel to Both HP and VP
25)A 50mm long line PQ is parallel to both the HP and the VP.It is 25mm in front of the VP and
60mm above the HP. Draw its projections and determine the traces.
5.Line Contained/lying in Both HP and VP

26)Draw the Projections of a 60mm long line PQ, which is situated both on the HP and the VP.
Also,determine the traces of the line.
6.Line inclined to Both HP and VP
27)End P is 20mm above the HP and 30mm in front of the VP and the end Q is 80mm above the HP
and 60 mm in front of the VP. The end projectors are 60mm apart.
28) End P is 30mm above the HP and 20mm in front of the VP and the end Q is 60mm above the HP
30) The projections on the XY line of the horizontal and vertical traces of a straight line AB in the first
quadrant are 120mm apart. The VT is 100mm above XY and the HT 50mm in front of XY. The Points
A and B are 30mm and 80mm above the HP respectively. Draw the Projections.
31)The front and top Views of 75mm long line PQ measures 50mm and 60mm respectively.If the end
P of the line is 35mm above the HP and 15mm infront of the VP.Draw its projections and locate the
traces.Determie the true inclinations of the line PQ with the HP and the VP.
32)The front and top views of a straight line PQ measures 50mm and 65mm,respectively.The point P
is on the HP and 20mm in front of the VP. The front View of the line is inclined at 45° to the reference
line. Determine the true length of PQ and its true inclinations with the reference planes. Also,Locate
the trace.
33)A line PQ inclined at an angle of 30° to the HP has ends P and Q 30mm and 65mm in front of the
VP respectively. The length of the top view is 60mm and its HT is 15mm in front of the VP. Draw the
projections of the in PQ and determine its true length and the VT.
34)A line PQ inclined at 30° to the VP has the end P 15mm above the HP.Its front view measures
70mm and is inclined at 45° to reference line.The VT of the line is 25mm below the HP.Draw the
projections of the line PQ and determine its true length and the HT.
Line inclined to Both HP and VP

35)A line CD measuring 80mm is inclined at an angle of 30° to HP and 45° to VP.The point C is
20mm above HP and 30mm infront of VP.Draw the Projections.
36)A 70mm long line PQ,has its end P 20mm above the HP and 30mm infront of the VP.The line is
inclined at 45° to the HP and 30° to the VP.Draw its projections.
37)A 100mm long line PQ has its end P 10mm above the HP and 70mm in front of the VP. The line is
inclined at 60° to the HP and 30° to the VP. Draw its projections.
38)A 70mm long line PQ is inclined at 45° to the VP. Its end P lies on the HP and 15mm in front of
the VP. The top view of the line measures 60mm.Draw the projections of the line PQ and determine its
inclination with the HP.
39) A straight line PQ has its end P 20mm above the HP and 30mm infront of the VP and the end Q is
80mm above the HP and 70mm infront of the VP.If the end projectors are 60mm apart,draw
projections of the line .Determine its true length and true inclinations with the reference planes.

40)A line LM 70mm long has its end L 10mm above HP and 15mmin front of VP. Its front and top
Views measure 40mm and 60mm respectively. Draw projections of the line. Find its inclinations With
HP and VP.
Mid-Point Problem
41)The mid-point of a straight line AB is 60mm above HP and 50mm in front of VP. The line
measures 80mm long and inclined at an angle of 30° to HP and 45° to VP. Draw its projections.
42) A 100mm long line PQ is inclined at 30° to the HP and 45° to the VP. Its mid point is 35mm
above the HP and 50mm in front of the VP. Draw its projections.
43) A line AB 120mm long is inclined at 45° to the HP and 30° to the VP .Its mid-point C is in VP and
20 mm above HP. The end A is in third quadrant and B is in first quadrant. Draw the projections of the
line.
44)A 75mm long line PQ lying in the first angle has its end P on the HP and end Q in the VP. The line
is inclined at 45° to the HP and 30° to the VP. Draw its projections.
45)A 70mm long line PQ has its end P 20mm above the HP and 40mm in front of the VP.The other
end Q is 60mm above the HP and 10mm in front of the VP.Draw the projections of PQ and determine
its inclinations with the reference Planes.
46) The top view of 75mm long line PQ measures 50mm.The end P is 15mm above the HP and 50mm
in front of the VP. The end Q is 20mm in front of the VP and above the HP.Draw the projections of
PQ and determine its inclinations with the reference planes
47)The front and top views of an 80mm long line PQ measures 70mm and 60mm respectively.The end
P is on the HP and the end Q is in the VP.Draw the projections of the line PQ and determine its
inclinations with the HP and the VP.Also locate the traces.
48)The distance between the end projectors of a line PQ is 50mm .The end P is 50mm in front of the
VP and 25mm above the HP .The end Q is 10mm infront of the VP.and above the HP.The line is
inclined at 30° to the VP.Draw the Projections of the line PQ. Determine its true length and true angle
of inclination with the HP.

Projection of Planes
Plane Parallel to HP
1. A square plane of side 40mm has its surface parallel to and 20mm above the HP. Draw its
projections when (a) a side is parallel to the VP.,(b)one side is inclined at 30° to the VP.
And(c) all sides are equally inclined to the VP.
Plane Parallel to VP
2. A hexagonal plane of side 25mm has its surface parallel to and 20mm in front of VP. Draw its
projections, when a side is (a) Parallel to the HP.,(b) perpendicular to the HP.,(c)inclined at 45°
to the HP.
Plane Parallel to Profile Plane
3. A triangular plane is in the form of an isosceles triangle of base side 30mm and altitude
40mm.Its surface is perpendicular to both HP and VP.Draw its projections when the base side
is parallel.
Plane inclined to HP and perpendicular to VP
4. A hexagonal plane of side 30mm has an edge on the HP. The surface is inclined at 45° to the
HP. and perpendicular to the VP. Draw its projections.
5. A hexagonal plane of side 30mm has a corner on the ground .Its surface is inclined at 45° to
the HP.and perpendicular to the VP.Draw its projections when the diagonal through the corner
in the HP is parallel to the VP.
6. A circular plane of diameter 50mm is resting on a point of the circumference on the HP.The
plane is inclined at 30° to the HP and its centre is 35mm in front of the VP.Draw its
Projections.
7. A rectangular plane of sides 70mm and 35mm has a shorter side on the HP.The surface of the
plane is inclined at 60° to the HP and perpendicular to the VP.Draw its projections.
8. A rhombus of diagonals 70mm and 45mm is placed on an end of the major diagonal on the
HP.Its surface is inclined at 50° to the HP and perpendicular to the VP.Draw its projections.
9. The top view of a plane whose surface is perpendicular to the VP and inclined at 45° to the HP
is a circle of diameter 50mm.Draw the projections of the plane and determine its true shape.
Plane inclined to VP and perpendicular to HP
10. A hexagonal plane of side 30mm has an edge in the VP. The surface of the plane is inclined at
45° to the VP. and perpendicular to the HP. Draw its projections.
11. A hexagonal plane of side 30mm has a corner in the VP. The surface of the plane is inclined at
45° to the VP. and perpendicular to the HP. Draw its projections. Assume that the diagonal
through the corner in the VP is parallel to the HP.
12. A circular plane of diameter 50mm is resting on appoint of the circumference on the VP. The
plane is inclined at 30° to the VP.and the centre is 35mm above the HP. Draw its projections.
13. An isosceles triangle of base 40mm and altitude 54mm has its base in the VP. The surface of
the plane is inclined at 50° to the VP and perpendicular to the HP. Draw its projections.
14. A 60° set-square has the shortest edge of 40mm lying in the VP. The surface is inclined to the
VP and perpendicular to the HP. Such that the front view appears as an isosceles triangle.
Draw the projections of the set-square and determine its inclination with the VP.

Special Case (Traces):
15. A rectangular plane of sides 40mm and 60mm has a corner on the HP and a corner on the HP
and 20mm in front of the VP. The surface of the plane is parallel to the VP .and all the sides
are equally inclined to the HP. Draw its projections
16. A thin hexagonal plate of side 30mm has a side inclined at 45° to the VP. Its VT is parallel and
25mm above the reference line. Draw its projections.
Plane inclined to Both the planes
17. A hexagonal plane of side 30mm has an edge on the HP.Its surface is inclined at 45° to the HP
and the edge on which the plane rests is inclined at 30° to the VP.Draw its Projections.
the HP.and the top view of the diagonal through the corner which is in the HP.makes an angle
of 60° with the VP.Draw its projections.
19. A pentagonal plane of side 30mm is resting on a corner in the HP.The side opposite to the
Corner in the HP is parallel to and 35mm above HP.and inclined at 45° to the VP.Draw its
three principal views.
20. The diagonal of a rhombus measure 100mm and 40mm.The longer diagonal is inclined at 30°
to HP.with an end in HP and the smaller diagonal is parallel to both the principal planes.Draw
its projections.
21. A rectangular plane of edges 35mm and 70mm is resting on an edge in the HP.The surface is
inclined to the HP.such that the top view appears as a square .Draw its projections when the
edge resting on the HP is inclined at 30° to the VP.
22. A thin square plate of side 40mm stands on one of its corners in the HP.and the opposite corner
is raised so that one of the diagonals is twice of the other.If one of the diagonals is parallel to
both the reference planes,draw its projections and determine the inclination of the Plate with
the HP.
23. A rhombus of diagonals 60mm and 40mm having the longer diagonal parallel to the reference
line represents the top view of a square lamina of diagonals 60mm resting on a corner on the
HP.Draw the front view of the lamina and determine inclination of its surface with the HP.
24. A hexagonal plane of side 30mm has an edge in the VP.The surface of the plane is inclined at
45° to the VP and the edge on which it rests is inclined at 30° to the HP. Draw its projections.
25. A hexagonal plane of side 30mm has a corner in the VP.The surface of the plane is inclined at
45° to the VP and perpendicular to the HP.The front view of the diagonal passing through that
corner is inclined at 60° to the HP.Draw its three principal Views.
26. A 30-60 set-square has it 75mm long hypotnuese in the VP and inclined at 30° to the HP.The
surface is inclined at 45° to the VP.Draw three views of the set-square.
27. A pentagon ABCDE of side 30mm has its side AB in the VP and inclined at 30° to the HP and
the corner B is 15mm above the HP and the corner D is 30mm infront of the VP.Draw the
projections of the plane and find its inclination with the VP.
28. A hexagonal plane ABCDEF of side 30mm has its corner A in the HP.The surface of the plane
is inclined at 45° to the HP.and the diagonal containing corner A is inclined at 30° to the
VP.Draw its Projections.
29. Draw the Projections of a circular plane of diameter 50mm resting on a point A of the
circumference on the HP such that its surface is inclined at 45° to the HP and(a)the top view of

the diameter through point A is inclined at 30° to the VP.(b)the diameter through point A is
inclined at 30° to the VP.

Unit-III
Projection of Solids
Axis perpendicular to HP
30. A square pyramid of side 40mm and axis 60mm is resting on its base on the HP.Draw its
projections when (a)a side of the base is parallel to the VP.,(b)a side of the base is inclined at
30° to the VP.,(c)all the sides are equally inclined to the VP.
31. A square prism of base side 40mm and axis 60mm is resting on its base on the ground.Draw its
projections when (a) a face is perpendicular to the VP.,(b)a face is inclined at 30° to the
VP.,(c)all the faces are equally inclined to the VP
Axis perpendicular to VP
32. A pentagonal prism of base side 30mm an axis 60mm has one of its bases in the VP.Draw its
projections when(a)a rectangular face is parallel to and 15mm above the HP.,(b)a face is
perpendicular to the HP.,(c)a face is inclined at 45° to the HP.
Axis Parallel to Both HP and VP
33. A pentagonal prism of base side 30mm and axis 60mm is resting on one of its rectangular faces
on the HP with axis parallel to the VP.Draw its Projections.
Axis inclined to HP and parallel to VP
34. A pentagonal prism of base edge 30mm and axis 60mm rests on an edge of its base in the
HP.Its axis is parallel to VP.and inclined at 45° to the HP.Draw its projections.
35. A pentagonal prism of base side 30mm and axis 70mm has a corner on the HP and the axis is
inclined at 45° to the HP.Draw its projection when the plane containing the resting corner and
the axis is parallel to the VP.
36. A hexagonal pyramid of base side 30mm and axis 60mm has an edge of its base on the ground.
Its axis is inclined at 30° to the ground and parallel to the VP.Draw its projections.
37. A hexagonal pyramid of base edge 30mm and axis 60mm,has a triangular face on the ground
and the axis parallel to the VP.Draw its projections.
38. A hexagonal pyramid of base edge 30mm and axis 60mm is lying on a slant edge on the
ground with the axis parallel to the VP.Draw its projections when the face containing the
resting edge are equally inclined to the HP.
39. A cylinder of base diameter 50mm and axis 70mm has a generator in the VP and inclined at
45° to the HP.Draw its projections.
40. A pentagonal pyramid of base side 30mm and axis 60mm has an edge of base parallel to HP.Its
axis is parallel to VP and inclined at 45° to the HP.Draw its projections when the apex lies in
the HP.
41. Draw projections of a cube of edge 45mm,resting on one of its corners in the HP with a solid
diagonal vertical.
42. A tetrahedron of edge 70mm has an edge on the ground and the faces containing that edge are
equally inclined to the HP.Draw its projections when the edge lying on the ground is
perpendicular to the VP.
Axis inclined to VP and Parallel to HP

43. A hexagonal prism of base edge 30mm and axis 70mm has an edge of its base in the VP.Such
that axis is inclined at 30° to the VP and parallel to the HP.Draw its projections.
44. A pentagonal pyramid of base side 30mm and axis 55mm has a triangular face in the VP and
the base edge contained by that triangular face is perpendicular to the HP.Draw its projections.
45. A cone of base diameter 50mm and axis 60mm has a generator in the VP and the axis parallel
to the HP.Draw its Projections.
46. A pentagonal prism of base side 30mm and axis 60mm has one of its rectangular faces on the
HP and the axis inclined at 60° to the VP.Draw its Projections.
Axis inclined to Both the HP and VP
47. A square prism of base edge 35mm and axis 60mm is resting on an edge of its base on the HP
and the axis is inclined at 45° to the HP.If the edge resting on an edge of its base on the HP is
inclined at 30° to the VP.Draw its projections.
48. A pentagonal prism of base side 30mm and height 60mm rests on one of its base side on the
HP inclined at 30° to the VP.Its axis is inclined at 45° to the HP.Draw its projections.
49. A square pyramid of base side 40mm and axis 55mm is resting on one of its triangular faces on
the HP.A vertical plane containing the axis is inclined at 45° to the VP.Draw its projections.
50. A hexagonal pyramid of base side 30mm and axis 60mm has an edge of its base on the ground
inclined at 45° to the VP.and the axis is inclined at 30° to the HP.Draw its projections.
51. A hexagonal pyramid of base side 30mm and axis 50mm rests on one of its base corners on the
ground with axis inclined at 45° to the HP.Draw its projections when a vertical plane
containing the axis and the corner that lies in the HP is inclined at 30° to the VP.
52. A hexagonal pyramid of base side 30mm and axis 60mm has one of its slant edges on the HP
and inclined at 45° to the VP.Draw its projections when the base is visible.
53. A hexagonal pyramid of base side 30mm and axis 60mm rests on an edge of base on the HP
with the triangular face containing that edge perpendicular to the HP and parallel to the
VP.Draw its projections so that the base is visible.
54. A pentagonal pyramid of base side 30mm and axis 60mm rests on a corner of its base on the
HP.Such that its apex is 55mm above the ground.A vertical plane containing the corner of the
base that lies on the HP and the axis is inclined at 30° to the VP.Draw its projections.
55. A pentagonal pyramid of base side 30mm and axis 60mm rests on an edge of its base on the
ground so that the highest point of the base is 20mm above the ground.Draw its projections
when a vertical plane containing the axis is inclined at 30° to the VP.
56. A cylinder of base diameter 50mm and axis 65mm rests on a point of its base circle on the
HP.Draw its projections when the axis is inclined at 30° to the HP.and top view of the axis is
57. Draw the projections of a cube of edge 40mm resting on one of its corners on the HP with a
solid diagonal perpendicular to the VP.
58. Asquare pyramid of base diagonal 50mm and axis 60mm is titled until the top view of the base
appears as a rhombus having one of the diagonal twice of the other.Draw its projections when
the axis as a vertical plane is inclined at 45° to the VP.
59. A tetrahedron of edge 70mm is resting on one of its edges in the HP which is inclined at 45° to
the VP and a face contained by that edge is inclined at 30° to the HP.Draw its Projections.

60. A pentagonal prism of base side 30mm and axis is 60mm has an edge of its base in the VP and
inclined at 45° to the HP.Its axis is inclined at 30° to the VP.Draw its projections.
61. A hexagonal prism of base edge 30mm and axis 70mm has an edge of its base in the VP and
inclined at 60° to the HP.Draw its projections when the edge of the other base farthest away
from VP is at a distance of 85mm from the VP.
62. A square pyramid of base side 40mm and axis 60mm has acorner of its base in the VP.A slant
edge contained by that corner is inclined at 45° to the VP.Draw its projections when a plane
containing the slant edge and the axis is inclined at 45° to the HP.
63. A cone of base diameter 50mm and axis 60mm has one of its generators in the VP and inclined
at 30° to the HP.Draw its projections when the apex is 15mm above the HP.
64. A hexagonal prism of base edge 30mm and axis 60mm rests on one of its base edges on the
HP.Such that the axis is inclined at 30° to the HP.and 45° to the VP.Draw its projections.
65. Draw the projections of a cone of base diameter 50mm and axis 60mm resting on a point of the
base circle on the ground with axis inclined at 30° to the HP.and(a)45° to the VP and(b)the top
view of the axis inclined at 45° to the VP.

UNIT-IV
Section of Solids
Section by a plane Perpendicular to VP.
1. A triangular prism, base side 50mm and axis 50mm is lying on one of its rectangular faces on
the HP with its axis perpendicular to the VP.It is cut by a section plane parallel to and 20mm
above HP. Draw its front view and sectional top view.
2. A triangular prism of base side 50mm and axis 50mm lies on one of its rectangular faces on the
HP with its axis inclined at 30° to the VP.It is cut by a horizontal section plane at a distance of
5mm from the axis. Draw its front view and sectional top view.
3. A square pyramid of base side 40mm and axis 60mm is resting on its base on the HP with a
side of base parallel to the VP.Draw its sectional views and true shape of the section,if it is cut
by a section plane perpendicular to the VP., bisecting the axis and is (a) Parallel to the
HP.,(b)inclined at 45°to the HP.(c)inclined at 60° to the HP.
4. A square pyramid of base side 40mm and axis 60mm is resting on its base on the HP with all
the sides of the base are equally inclined to the VP.Draw its sectional views and true shape of
the section,if it is cut by a section plane perpendicular to the VP bisecting the axis and
is(a)Parallel to the HP(b)inclined at 45° to the HP and (c)inclined at 60° to the HP.
5. A pentagonal pyramid of base side 30mm and axis 60mm is resting on its base in the HP with
an edge parallel to the VP.A horizontal section plane cuts the pyramid bisecting the axis.Draw
its front view and sectional top view.
6. A pentagonal pyramid of base side 30mm and axis 60mm is resting on its base on the HP with
an edge of the base parallel to the VP.It is cut by a section plane perpendicular to the VP
inclined at 60° to the HP. and bisecting the axis. Draw its front view and sectional top view and
true shape of the section.
7. A pentagonal pyramid of base side 30mm and axis 60mm is on a triangular face in the HP with
its axis parallel to the VP. It is cut by A.I.P inclined at 60° to the HP and passing through the
highest point of the base. Draw its sectional top view and true shape of the section.
8. A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.It is cut by an
A.I.P inclined at 45° to the HP and passing through a point on the axis,20mm above the
base.Draw its sectional top view and obtain true shape of the section.
9. A cone of base diameter 50mm and axis 60mm long is resting on its base on the HP.It is cut by
an A.I.P bisecting the axis inclined at 45° to the HP.Draw its sectional top view and true shape
of the section.
A.I.P parallel to one of the extreme generators passing through a point on the axis 40mm from
its base.Draw its sectional top view and obtain true shape of the section.
11. A cylinder of base diameter 50mm and axis 60mm is resting on its base on the HP.It is cut by a
section plane perpendicular to VP.the VT of which cuts the axis at appoint 40mm from the
bottom face and inclined at 45° to the reference line.Draw its front view ,sectional top view
and true shape of the section.
12. A pentagonal prism of base side 30mm and axis 70mm has an edge of its base on the HP.The
axis is parallel to the VP and inclined at 60° to the HP.It is cut by an A.I.P inclined at 60° to

the HP and passing through the highest corner of the prism. Draw its sectional top view an true
shape of the section.
13. A hexagonal prism of base side 30mm and axis 70mm is resting on a face on the HP with axis
parallel to the VP.It is cut by a plane whose VT is inclined at 30° to the reference line and
passes through a point on the axis 20mm from one of its ends.Draw its sectional top view and
obtain true shape of the section.

14. A square prism of base side 40mm and axis 60mm rests on its base on the HP.such that one of
its rectangular faces is inclined at 30° to the VP.It is cut by a section plane parallel to VP
bisecting a face of the pris which is inclined at 30° to the VP.Draw its sectional front view and
top view.
its rectangular faces is inclined at 30° to the VP.It is cut by a section plane perpendicular to HP
and inclined at 60° to VP passing through the prism such that a face is inclined at 60° to the VP
is bisected.Draw its sectional front view ,top view and true shape of section.
16. A pentagonal prism of base side 30mm and axis 60mm lies on one of its rectangular faces on
the HP.with its axis inclined at 45° to the VP.A vertical section plane parallel to the VP cuts
the prism at a distance of 20mm from one of the end faces. Draw its sectional front view and
top view.
17. A hexagonal prism of base side 30mm and axis 70mm has an edge of its base on the HP with
axis parallel to the VP and inclined at 45° to the HPs.It is cut by an AVP inclined at 45° to the
VP and passing through a point on the axis, 15mm from the top end. Draw its sectional front
view and obtain true shape of the section.
18. A hexagonal prism of base side 30mm and axis 70mm is resting on a face on the ground with
axis parallel to the VP .It is cut by AVP which is inclined at 45° to the VP and passes through a
point 25mm on the axis from one of its ends. Draw its sectional front view and obtain true
a base parallel to VP and nearer to it.It is cut by a section plane parallel to the VP and 12mm in
front of the axis of the pyramid. Draw its sectional front view and top view.
an edge of the base nearer the VP parallel to it. A vertical section plane inclined at 45° to the
VP cuts the pyramid at a distance of 8mm from the axis .Draw its sectional front view top view
21. A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.It is cut by a
section plane whose HT is inclined at 60° to the reference line and passes through a point
15mm away from the axis.Draw its sectional front view and obtain true shape of the section.
22. A pentagonal pyramid of base side 30mm and axis 60mm is resting on a triangular face on the
HP with its axis parallel to the VP.It is cut by a plane whose HT is inclined at 30° to the
reference line and bisects the axis such that the apex is removed.Draw its sectional front view
and obtain true shape of the section.

Section by a plane Perpendicular to Both HP and VP.
23. A square prism of base side 40mm and axis 60mm rests on its base on the HP.Such that one of
its faces is inclined at 30° to the VP.It is cut by a section plane perpendicular to both the HP
and the VP passing through one of the vertical edges.Draw its front view ,top view and
sectional side view.
Development of surfaces
1. A square prism of base side 30mm and axis 60mm is resting on its base on the HP with a
rectangular face parallel to the VP.Draw the development of the prism.
2. A pentagonal prism of base side 30mm and axis 70mm is resting on its base on the HP with a
rectangular face parallel to the VP.It is cut by an auxiliary inclined plane(A.I.P) whose VT is
inclined at 45° to the reference line and passes through the mid-point of the axis .Draw the
development of the lateral surface of the truncated prism.
3. A hexagonal prism of base side 30mm and axis 70mm is resting on its base on the ground with
a side of base inclined at 45° to the VP.It is cut by an auxiliary inclined plane inclined at 45° to
the HP and passes through a point 15mm below the top end of the axis.Draw the development
of the lateral surface of the truncated prism.
4. A hexagonal prism of base side 30mm and height 70mm is resting on its base on the HP with a
side of base perpendicular to the VP.The prism has a cylindrical hole of diameter 40mm,drilled
centrally such that the axis of hole is perpendicular to the VP.Draw the development of the
lateral surface of the prism.
5. Fig shows the front view of a truncated hexagonal prism of base side 30mm and axis
90mm.The prism is resting on the HP with an edge of the base parallel to the VP.Draw the
development of its lateral surface.
6. The pentagonal prism of side 30mm rests on its base on the HP.It is cut by A.I.P. inclined at
30° to the HP and passes through the top end of the axis.Also,a cylindrical hole of diameter
40mm is drilled perpendicular to the VP the axis of which is 5mm away from theaxis of the
prism as shown in fig below.Draw the development of its lateral surface.
7. A cylinder of base diameter 50mm and axis 70mm is resting on ground with its axis vertical. It
is cut by a section plane perpendicular to the VP inclined at 45° to the HP passing through the
top of a generator and cuts all the other generators. Draw the development of its lateral surface.
8. A square hole of side 25mm is cut in a cylindrical drum of diameter 50mm and height
70mm.The faces of the hole are inclined at 45° to the HP and axis intersects with that of the
drum at right angles.Draw the development of its lateral surface.
9. Figure shows the front view of a truncated cylinder of diameter 50mm resting on its base on
the HP.Draw the development of its lateral surface.
10. A cylindrical drum of base diameter 50mm and axis 70mm is resting on its base on the HP.A
square hole of side 40mm is cut through the drum such that one of the faces of the square hole
is inclined at 30° to the HP.The axis of the hole is perpendicular to the VP and is 10mm away
from the axis of the cylinder.Draw the development of the retained Cylinder.
11. An object is composed of truncated half-cylinder and half-prism whose projections are given in
Fig.Draw the development of its lateral surface.

12. A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.Draw the
13. A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.A section plane
perpendicular to VP and inclined at 45° to HP bisects the axis of the cone.Draw the
development of its lateral surface when it is cut by an auxiliary inclined plane inclined at 60° to
the HP and bisecting the axis.
15. The frustum of a cone of base diameter 60mm,top diameter 20mm and height 50mm is resting
on its base on the HP.It is cut by an A.I.P inclined at 30° to the HP,the HT of which is
tangential to the base circle.Draw the development of the lateral surface of the retained
frustum.
16. A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.A square hole
of diagonal 25mm is drilled through it such that axis of the hole intersects the axis of the cone
at a height of 20mm from the base.The faces of the hole are equally inclined to the HP.Draw
the development of its lateral surface.
17. Draw the development of the lateral surface of a square pyramid of base side 40mm and axis
60mm resting on its base on the HP such that (a)all the sides of the base are equally inclined to
the VP and (b)a side of the base is parallel to the VP
18. A square pyramid of base side 40mm and axis 60mm is resting on its base on the HP such that
a side of the base is parallel to the VP.It is cut by a section plane perpendicular to the VP and
inclined at 45° to the HP bisecting the axis. Draw the development of its lateral surface.
all the sides of the base are equally inclined to the VP.It is cut by a section plane perpendicular
to the VP and inclined at 60° to the HP bisecting the axis. Draw the development of its lateral
surface.
20. A pentagonal pyramid of base side 30mm and axis 60mm rests on its base on the HP with a
side of base parallel to the VP.It is cut by two section plane which meet at a height of 20mm
from the base. One of the section planes is horizontal, while the other is an auxiliary inclined
plane whose VT is inclined at 45° to the HP. Draw the development of the lateral surface of the
solid when apex is removed.

UNIT-V
Isometric Projections
1) Transform orthographic Projections to Isometric Projections


6) Transform Isometric Projections to orthographic Projections



College Question Bank
Unit-I
Conic Sections
Construction of Ellipse
General Method
1)Draw an ellipse when the distance of its focus from its directrix is 50mm and the eccentricity is
2/3.Also draw a normal and tangent to the ellipse at a point 70mm away from the directrix.
Intersecting Arcs Method or Arcs of Circle Method
2)A point moves in a plane in such a way that the sum of its distances from two fixed points
100mm apart .Name and draw the locus of this point.
Concentric Circle Method
3)The major axis of an ellipse is 110mm and minor axis is 70mm long .Draw an ellipse by
concentric circle method.
Rectangle Method
4) Inscribe the largest possible ellipse in a rectangle of sides 160mm and 100mm.
5) The conjugate diameters of an ellipse are 110mm and 80mm and the include angle between
them is 75° .Draw an ellipse by parallelogram method.
Construction of Parabola
General Method
6) Draw a parabola when the distance between its focus and directrix is 50mm.Also draw a tangent
and a normal at a point 70mm from the directrix.
Offset Method
7) A parabolic arch has a span of 160mm and a maximum rise of 100mm .Draw a curve using
offset method .
Tangent Method
8)Draw a parabola of base 150mm and axis 80mm by tangent method.
Rectangle Method/Oblong Method
9)Draw a parabola of base 120mm and axis 80mm by oblong method.
10)Inscribe a parabola in parallelogram of sides 110mm and 80mm,the included angle being
60°.Consider the longer side of the parallelogram as the base of the parabola.

Construction of Hyperbola
General Method
11)Draw a hyperbola when the distance of its focus from its directrix is 50mm and eccentricity is
3/2.Also draw a tangent and a normal to the hyperbola at a point 25mm from the directrix.
Intersecting Arcs Method
12)Two fixed points are 80mm apart.Draw the locus of a point P which moves in such a manner
that the difference of its distance from the fixed points is always the same and equal to
60mm.Name the crve.
Oblong Method
13)Draw a hyperbola when half the transverse axis, double ordinate and abscissa are 50mm
120mm and 40mm long respectively.
Intercept Method
14)Draw a rectangular hyperbola when the position of a point P on the curve is at a distance of
30mm and 50mm from two asymptotes.
Orthogonal Asymptotes Method
15)A point P of the hyperbola at a distance of 35mm and 50mm from the pair of asymptotes.The
asymptotes are perpendicular to each other.Draw a hyperbola using orthogonal asymptotes
method.
Oblique Asymptotes Method
16)Draw a hyperbola when its asymptotes are inclined at 60° to each other and passes through a
point P.The point P is at a diatance of 40mm and 50mm from the asymptotes.
Locating Asymptotes and Directrix
17) Draw two branches of hyperbola having foci 70mm apart and vertices 40mm apart. Locate the
asymptotes and measure the included angle. Also locate the directrix of the hyperbola.
Construction of Cycloids and Involutes

Cycloid
18) Draw a cycloid of a circle of diameter 50mm for one revolution .Also draw a tangent and a
normal to the curve at a point 35mm above the base line.
Epicycloid
19) Draw an epicycloids of rolling circle 40mm diameter, which rolls outside another circle(Base
Circle) of 150mm diameter for one revolution. Draw a tangent & normal at a point 110mm from
center of the directing circle.
Hypocycloid
20)Draw a hypocycloid of a circle of 40mm diameter which rolls inside another circle of 200mm
diameter for one revolution. Draw a tangent and normal at a point of 80mm on the curve
generated.

Involutes
21)Draw the involute of an equilateral triangle of side 25mm.
22)Construct the involute of a pentagon of 22mm side
Unwound
23) A coir is unwound from a drum of 30mm diameter. Draw the locus of the free end of the coir
for unwinding through an angle of 360°.Draw also a normal and tangent at any point on the curve.
Wound
24) An elastic string of length 100mm is wound round a circle of 26mm diameter. Draw the path
traced by the end of the string.
Scales
Plain Scale
25) Construct a scale of 1:40 to read meters and decimeters and long enough to measure up to 6
meters. Mark a distance of 4.7m on it.
26) If 1 centimeter long line on a map represents a real length of 4 meters .Calculate the RF and
draw a plain scale long enough to measure up to 50metres.Show a distance of 44m on it.
27)A real length of 1 decameter is represented by a line of 5cm in a drawing .Find the RF and
construct a plain scale to measure up to 2.5 decameters. Mark a distance of 19m on it.
Diagonal Scale
28) Construct a scale of 1:40 to read meters, decimeters and centimeters and long enough to
measure up to 6m.Mark a distance of 4.76m on it.
29) If 1cm long line on a map represents a real length of 4m.Calculate the RF and draw a diagonal
scale long enough to measure up to 50metres.Show a distance of 44.5m on it.
30) The distance between two stations by road is 200km and it is represented on a certain map by
a 5cm long line. Find the RF and construct a diagonal scale showing single kilometer and long
enough to measure up to 600km.Show a distance of 467 km on this scale.

Unit-II
Introduction to Orthographic Projection

Unit-II
Projection of points
Projection of a point situated in First quadrant
1) A Point A is 20 mm above H.P and 30 mm in front of V.P. Draw the Projections of the point.
Projection of a point situated in Second quadrant
2) A Point B is 20 mm above H.P and 30 mm behind V.P. Draw the Projections of the point.
Projection of a point situated in Third quadrant
3) A Point C is 20 mm below H.P and 30 mm behind V.P. Draw the Projections of the point.
Projection of a point situated in Fourth quadrant
4) A Point D is 20 mm below H.P and 30 mm in front of V.P. Draw the Projections of the point.
Point situated in Both H.P and V.P
5) Draw the projections of a point J, lying on both the H.P and the V.P
Point on H.P and in front of V.P
6) Draw the projections of a point E, lying the H.P and 50 mm in front of V.P
Point above the H.P and on the V.P
7) Draw the projections of a point F, lying 70 mm above H.P and on the V.P
Projections of a point situated in First Quadrant
8) A point A is 20mm above HP,30mm in front of VP and 25 in front of PP. Draw its front view,top
view and left side view of the point

1. Line Parallel to Both HP and VP
9) A line CD 30mm long is parallel to both the planes. The line is 40mm above HP and 25mm in front
of VP. Draw its Projections.
2. Line Contained/lying in one Plane & Parallel to other
a) Line Contained in HP and Parallel to VP
10) A line RS 60 mm long lies in HP and 45mm in front of VP. Draw its Projections.
b) Line Contained in VP and Parallel to HP
11) A line PQ 55 mm long lies in VP and 45mm above HP. Draw its Projections.
3. Line Contained/lying in Both HP and VP
12) A line AB 55 mm long is lying on both HP and VP. Draw its Projections.
4. Line perpendicular to one Plane and Parallel to the other
13) A line AB 25 mm long is parallel to VP and perpendicular to HP. Point A is 35mm above HP and
20mm in front of VP. Point B is 10mm above HP. Draw the Projections of the line AB
14) A line AB 25 mm long is perpendicular to VP and parallel to HP. Its end A is 10mm in front of VP
and the line is20mm above HP. Draw the Projections of the line.
5. Line Parallel to one Plane & Inclined to other
a) Line Parallel to VP and inclined to HP
15) A line PQ 40 mm long is parallel to VP and inclined at an angle of 30° to HP. The Lower end P is
15mm above HP and 20mm in front of VP. Draw the projections of the line.
b) Line parallel to HP and inclined to VP
16) Draw the projections of a line EF 40mm long parallel to HP and inclined at 35° to VP. E is 20mm
above HP and 15mm in front of VP.
6. Line contained by one Plane & Inclined to other
a) Line contained by VP and inclined to HP
17) A line AB 50mm long is in VP and inclined at an angle of 35° to HP. The end A is 10mm above
HP. Draw the Projections.
b) Line contained by HP and inclined to VP
18) A line RS measuring 52mm is in HP and inclined at an angle of 45° to VP. The end R is 10mm in
front of VP. Draw the Projections.

Traces
1.Line perpendicular to one Plane and Parallel to the other
19) A 60mm long line PQ has its end P 20mm above HP. The line is perpendicular to the HP and
40mm in front of the VP. Draw its projections and locate the traces.
20)A 60mm long line PQ has its end P 20mm in front of the VP.The line is perpendicular to the VP
and 40 mm above the HP.Draw the projections of the line and determine its traces.
2.Line Parallel to one Plane & Inclined to other
a)Line Parallel to VP and inclined to HP
21)A 80mm long line PQ has end P 20mm above HP and 40mm in front of the VP.The line is inclined
at 30° to the HP and is parallel to the VP. Draw the projections of the line and determine its traces
b)Line parallel to HP and inclined to VP
22)An 80mm long line PQ is inclined at 30° to the VP and is parallel to the HP. The end P of the line
is 20mm above the HP and 40mm in front of the VP. Draw the projections of the line and determine its
traces .
3.Line contained by one Plane & Inclined to other
a)Line contained by VP and inclined to HP
23)Draw the projections of a 70mm long line PQ,situated in the VP and inclined at 30° to the HP. The
end P of the line is 25mm above the HP. Also, determine the traces of the line.
b)Line contained by HP and inclined to VP
24)A 60mm long line PQ lying on the HP is inclined at 30° to the VP. Its end P is 20mm in front of
the VP. Draw the projections of the line and determine its traces .
4.Line Parallel to Both HP and VP
25)A 50mm long line PQ is parallel to both the HP and the VP.It is 25mm in front of the VP and
60mm above the HP. Draw its projections and determine the traces.
5.Line Contained/lying in Both HP and VP
26)Draw the Projections of a 60mm long line PQ, which is situated both on the HP and the VP.
Also,determine the traces of the line.
6.Line inclined to Both HP and VP
28) End P is 30mm above the HP and 20mm in front of the VP and the end Q is 60mm above the HP
30) The projections on the XY line of the horizontal and vertical traces of a straight line AB in the first
quadrant are 120mm apart. The VT is 100mm above XY and the HT 50mm in front of XY. The Points
A and B are 30mm and 80mm above the HP respectively. Draw the Projections.
31)The front and top Views of 75mm long line PQ measures 50mm and 60mm respectively.If the end
P of the line is 35mm above the HP and 15mm infront of the VP.Draw its projections and locate the
traces.Determie the true inclinations of the line PQ with the HP and the VP.

32)The front and top views of a straight line PQ measures 50mm and 65mm,respectively.The point P
is on the HP and 20mm in front of the VP. The front View of the line is inclined at 45° to the reference
line. Determine the true length of PQ and its true inclinations with the reference planes. Also,Locate
the trace.
33)A line PQ inclined at an angle of 30° to the HP has ends P and Q 30mm and 65mm in front of the
VP respectively. The length of the top view is 60mm and its HT is 15mm in front of the VP. Draw the
projections of the in PQ and determine its true length and the VT.
34)A line PQ inclined at 30° to the VP has the end P 15mm above the HP.Its front view measures
70mm and is inclined at 45° to reference line.The VT of the line is 25mm below the HP.Draw the
projections of the line PQ and determine its true length and the HT.
Line inclined to Both HP and VP

35)A line CD measuring 80mm is inclined at an angle of 30° to HP and 45° to VP.The point C is
20mm above HP and 30mm infront of VP.Draw the Projections.
36)A 70mm long line PQ,has its end P 20mm above the HP and 30mm infront of the VP.The line is
inclined at 45° to the HP and 30° to the VP.Draw its projections.
37)A 100mm long line PQ has its end P 10mm above the HP and 70mm in front of the VP. The line is
inclined at 60° to the HP and 30° to the VP. Draw its projections.
38)A 70mm long line PQ is inclined at 45° to the VP. Its end P lies on the HP and 15mm in front of
the VP. The top view of the line measures 60mm.Draw the projections of the line PQ and determine its
inclination with the HP.
39) A straight line PQ has its end P 20mm above the HP and 30mm infront of the VP and the end Q is
40)A line LM 70mm long has its end L 10mm above HP and 15mmin front of VP. Its front and top
HP and VP.
Mid-Point Problem
41)The mid-point of a straight line AB is 60mm above HP and 50mm in front of VP. The line
measures 80mm long and inclined at an angle of 30° to HP and 45° to VP. Draw its projections.
42) A 100mm long line PQ is inclined at 30° to the HP and 45° to the VP. Its mid point is 35mm
above the HP and 50mm in front of the VP. Draw its projections.
43) A line AB 120mm long is inclined at 45° to the HP and 30° to the VP .Its mid-point C is in VP and
line.
44)A 75mm long line PQ lying in the first angle has its end P on the HP and end Q in the VP. The line
is inclined at 45° to the HP and 30° to the VP. Draw its projections.
45)A 70mm long line PQ has its end P 20mm above the HP and 40mm in front of the VP.The other
end Q is 60mm above the HP and 10mm in front of the VP.Draw the projections of PQ and determine
its inclinations with the reference Planes.

46) The top view of 75mm long line PQ measures 50mm.The end P is 15mm above the HP and 50mm
48)The distance between the end projectors of a line PQ is 50mm .The end P is 50mm in front of the

Projection of Planes
Plane Parallel to HP
66. A square plane of side 40mm has its surface parallel to and 20mm above the HP. Draw its
projections when (a) a side is parallel to the VP.,(b)one side is inclined at 30° to the VP.
And(c) all sides are equally inclined to the VP.
Plane Parallel to VP
67. A hexagonal plane of side 25mm has its surface parallel to and 20mm in front of VP. Draw its
projections, when a side is (a) Parallel to the HP.,(b) perpendicular to the HP.,(c)inclined at 45°
to the HP.
Plane Parallel to Profile Plane
68. A triangular plane is in the form of an isosceles triangle of base side 30mm and altitude
40mm.Its surface is perpendicular to both HP and VP.Draw its projections when the base side
is parallel.
Plane inclined to HP and perpendicular to VP
69. A hexagonal plane of side 30mm has an edge on the HP. The surface is inclined at 45° to the
HP. and perpendicular to the VP. Draw its projections.
the HP.and perpendicular to the VP.Draw its projections when the diagonal through the corner
in the HP is parallel to the VP.
71. A circular plane of diameter 50mm is resting on a point of the circumference on the HP.The
plane is inclined at 30° to the HP and its centre is 35mm in front of the VP.Draw its
Projections.
72. A rectangular plane of sides 70mm and 35mm has a shorter side on the HP.The surface of the
plane is inclined at 60° to the HP and perpendicular to the VP.Draw its projections.
73. A rhombus of diagonals 70mm and 45mm is placed on an end of the major diagonal on the
HP.Its surface is inclined at 50° to the HP and perpendicular to the
VP.Draw its projections.
74. The top view of a plane whose surface is perpendicular to the VP and inclined at 45° to the HP
is a circle of diameter 50mm.Draw the projections of the plane and determine its true shape.
Plane inclined to VP and perpendicular to HP
75. A hexagonal plane of side 30mm has an edge in the VP. The surface of the plane is inclined at
45° to the VP. and perpendicular to the HP. Draw its projections.
76. A hexagonal plane of side 30mm has a corner in the VP. The surface of the plane is inclined at
45° to the VP. and perpendicular to the HP. Draw its projections. Assume that the diagonal
through the corner in the VP is parallel to the HP.
77. A circular plane of diameter 50mm is resting on appoint of the circumference on the VP. The
plane is inclined at 30° to the VP.and the centre is 35mm above the HP. Draw its projections.
78. An isosceles triangle of base 40mm and altitude 54mm has its base in the VP. The surface of
the plane is inclined at 50° to the VP and perpendicular to the HP. Draw its projections.

79. A 60° set-square has the shortest edge of 40mm lying in the VP. The surface is inclined to the
VP and perpendicular to the HP. Such that the front view appears as an isosceles triangle.
Draw the projections of the set-square and determine its inclination with the VP.
Special Case (Traces):
80. A rectangular plane of sides 40mm and 60mm has a corner on the HP and a corner on the HP
and 20mm in front of the VP. The surface of the plane is parallel to the VP .and all the sides
are equally inclined to the HP. Draw its projections
81. A thin hexagonal plate of side 30mm has a side inclined at 45° to the VP. Its VT is parallel and
25mm above the reference line. Draw its projections.
Plane inclined to Both the planes
82. A hexagonal plane of side 30mm has an edge on the HP.Its surface is inclined at 45° to the HP
and the edge on which the plane rests is inclined at 30° to the VP.Draw its Projections.
the HP.and the top view of the diagonal through the corner which is in the HP.makes an angle
of 60° with the VP.Draw its projections.
84. A pentagonal plane of side 30mm is resting on a corner in the HP.The side opposite to the
Corner in the HP is parallel to and 35mm above HP.and inclined at 45° to the VP.Draw its
three principal views.
85. The diagonal of a rhombus measure 100mm and 40mm.The longer diagonal is inclined at 30°
to HP.with an end in HP and the smaller diagonal is parallel to both the principal planes.Draw
its projections.
86. A rectangular plane of edges 35mm and 70mm is resting on an edge in the HP.The surface is
inclined to the HP.such that the top view appears as a square .Draw its projections when the
edge resting on the HP is inclined at 30° to the VP.
87. A thin square plate of side 40mm stands on one of its corners in the HP.and the opposite corner
is raised so that one of the diagonals is twice of the other.If one of the diagonals is parallel to
both the reference planes,draw its projections and determine the inclination of the Plate with
the HP.
88. A rhombus of diagonals 60mm and 40mm having the longer diagonal parallel to the reference
line represents the top view of a square lamina of diagonals 60mm resting on a corner on the
HP.Draw the front view of the lamina and determine inclination of its surface with the HP.
89. A hexagonal plane of side 30mm has an edge in the VP.The surface of the plane is inclined at
45° to the VP and the edge on which it rests is inclined at 30° to the HP. Draw its projections.
90. A hexagonal plane of side 30mm has a corner in the VP.The surface of the plane is inclined at
45° to the VP and perpendicular to the HP.The front view of the diagonal passing through that
corner is inclined at 60° to the HP.Draw its three principal Views.
91. A 30-60 set-square has it 75mm long hypotnuese in the VP and inclined at 30° to the HP.The
surface is inclined at 45° to the VP.Draw three views of the set-square.
92. A pentagon ABCDE of side 30mm has its side AB in the VP and inclined at 30° to the HP and
the corner B is 15mm above the HP and the corner D is 30mm infront of the VP.Draw the
projections of the plane and find its inclination with the VP.

93. A hexagonal plane ABCDEF of side 30mm has its corner A in the HP.The surface of the plane
is inclined at 45° to the HP.and the diagonal containing corner A is inclined at 30° to the
VP.Draw its Projections.
94. Draw the Projections of a circular plane of diameter 50mm resting on a point A of the
circumference on the HP such that its surface is inclined at 45° to the HP and(a)the top view of
the diameter through point A is inclined at 30° to the VP.(b)the diameter through point A is
inclined at 30° to the VP.

Unit-III
Projection of Solids
Axis perpendicular to HP
95. A square pyramid of side 40mm and axis 60mm is resting on its base on the HP.Draw its
projections when (a)a side of the base is parallel to the VP.,(b)a side of the base is inclined at
30° to the VP.,(c)all the sides are equally inclined to the VP.
96. A square prism of base side 40mm and axis 60mm is resting on its base on the ground.Draw its
projections when (a) a face is perpendicular to the VP.,(b)a face is inclined at 30° to the
VP.,(c)all the faces are equally inclined to the VP
Axis perpendicular to VP
97. A pentagonal prism of base side 30mm an axis 60mm has one of its bases in the VP.Draw its
projections when(a)a rectangular face is parallel to and 15mm above the HP.,(b)a face is
perpendicular to the HP.,(c)a face is inclined at 45° to the HP.
Axis Parallel to Both HP and VP
98. A pentagonal prism of base side 30mm and axis 60mm is resting on one of its rectangular faces
on the HP with axis parallel to the VP.Draw its Projections.
Axis inclined to HP and parallel to VP
99. A pentagonal prism of base edge 30mm and axis 60mm rests on an edge of its base in the
HP.Its axis is parallel to VP.and inclined at 45° to the HP.Draw its projections.
100. A pentagonal prism of base side 30mm and axis 70mm has a corner on the HP and the
axis is inclined at 45° to the HP.Draw its projection when the plane containing the resting
corner and the axis is parallel to the VP.
101. A hexagonal pyramid of base side 30mm and axis 60mm has an edge of its base on the
ground. Its axis is inclined at 30° to the ground and parallel to the VP.Draw its projections.
102. A hexagonal pyramid of base edge 30mm and axis 60mm,has a triangular face on the
ground and the axis parallel to the VP.Draw its projections.
103. A hexagonal pyramid of base edge 30mm and axis 60mm is lying on a slant edge on the
ground with the axis parallel to the VP.Draw its projections when the face containing the
resting edge are equally inclined to the HP.
104. A cylinder of base diameter 50mm and axis 70mm has a generator in the VP and
inclined at 45° to the HP.Draw its projections.
105. A pentagonal pyramid of base side 30mm and axis 60mm has an edge of base parallel
to HP.Its axis is parallel to VP and inclined at 45° to the HP.Draw its projections when the
apex lies in the HP.
106. Draw projections of a cube of edge 45mm,resting on one of its corners in the HP with a
solid diagonal vertical.
107. A tetrahedron of edge 70mm has an edge on the ground and the faces containing that
edge are equally inclined to the HP.Draw its projections when the edge lying on the ground is
Axis inclined to VP and Parallel to HP
108. A hexagonal prism of base edge 30mm and axis 70mm has an edge of its base in the
VP.Such that axis is inclined at 30° to the VP and parallel to the HP.Draw its projections.

109. A pentagonal pyramid of base side 30mm and axis 55mm has a triangular face in the
VP and the base edge contained by that triangular face is perpendicular to the HP.Draw its
projections.
110. A cone of base diameter 50mm and axis 60mm has a generator in the VP and the axis
parallel to the HP.Draw its Projections.
111. A pentagonal prism of base side 30mm and axis 60mm has one of its rectangular faces
on the HP and the axis inclined at 60° to the VP.Draw its Projections.
Axis inclined to Both the HP and VP
112. A square prism of base edge 35mm and axis 60mm is resting on an edge of its base on
the HP and the axis is inclined at 45° to the HP.If the edge resting on an edge of its base on the
HP is inclined at 30° to the VP.Draw its projections.
113. A pentagonal prism of base side 30mm and height 60mm rests on one of its base side
on the HP inclined at 30° to the VP.Its axis is inclined at 45° to the HP.Draw its projections.
114. A square pyramid of base side 40mm and axis 55mm is resting on one of its triangular
faces on the HP.A vertical plane containing the axis is inclined at 45° to the VP.Draw its
projections.
115. A hexagonal pyramid of base side 30mm and axis 60mm has an edge of its base on the
ground inclined at 45° to the VP.and the axis is inclined at 30° to the HP.Draw its projections.
116. A hexagonal pyramid of base side 30mm and axis 50mm rests on one of its base
corners on the ground with axis inclined at 45° to the HP.Draw its projections when a vertical
plane containing the axis and the corner that lies in the HP is inclined at 30° to the VP.
117. A hexagonal pyramid of base side 30mm and axis 60mm has one of its slant edges on
the HP and inclined at 45° to the VP.Draw its projections when the base is visible.
118. A hexagonal pyramid of base side 30mm and axis 60mm rests on an edge of base on
the HP with the triangular face containing that edge perpendicular to the HP and parallel to the
VP.Draw its projections so that the base is visible.
119. A pentagonal pyramid of base side 30mm and axis 60mm rests on a corner of its base
on the HP.Such that its apex is 55mm above the ground.A vertical plane containing the corner
of the base that lies on the HP and the axis is inclined at 30° to the VP.Draw its projections.
120. A pentagonal pyramid of base side 30mm and axis 60mm rests on an edge of its base
on the ground so that the highest point of the base is 20mm above the ground.Draw its
projections when a vertical plane containing the axis is inclined at 30° to the VP.
121. A cylinder of base diameter 50mm and axis 65mm rests on a point of its base circle on
the HP.Draw its projections when the axis is inclined at 30° to the HP.and top view of the axis
is perpendicular to the VP.
122. Draw the projections of a cube of edge 40mm resting on one of its corners on the HP
with a solid diagonal perpendicular to the VP.
123. Asquare pyramid of base diagonal 50mm and axis 60mm is titled until the top view of
the base appears as a rhombus having one of the diagonal twice of the other.Draw its
projections when the axis as a vertical plane is inclined at 45° to the VP.

124. A tetrahedron of edge 70mm is resting on one of its edges in the HP which is inclined
at 45° to the VP and a face contained by that edge is inclined at 30° to the HP.Draw its
Projections.
125. A pentagonal prism of base side 30mm and axis is 60mm has an edge of its base in the
VP and inclined at 45° to the HP.Its axis is inclined at 30° to the VP.Draw its projections.
126. A hexagonal prism of base edge 30mm and axis 70mm has an edge of its base in the
VP and inclined at 60° to the HP.Draw its projections when the edge of the other base farthest
away from VP is at a distance of 85mm from the VP.
127. A square pyramid of base side 40mm and axis 60mm has acorner of its base in the
VP.A slant edge contained by that corner is inclined at 45° to the VP.Draw its projections
when a plane containing the slant edge and the axis is inclined at 45° to the HP.
128. A cone of base diameter 50mm and axis 60mm has one of its generators in the VP and
inclined at 30° to the HP.Draw its projections when the apex is 15mm above the HP.
129. A hexagonal prism of base edge 30mm and axis 60mm rests on one of its base edges on
the HP.Such that the axis is inclined at 30° to the HP.and 45° to the VP.Draw its projections.
130. Draw the projections of a cone of base diameter 50mm and axis 60mm resting on a
point of the base circle on the ground with axis inclined at 30° to the HP.and(a)45° to the VP
and(b)the top view of the axis inclined at 45° to the VP.

UNIT-IV
Section of Solids
24. A triangular prism, base side 50mm and axis 50mm is lying on one of its rectangular faces on
the HP with its axis perpendicular to the VP.It is cut by a section plane parallel to and 20mm
above HP. Draw its front view and sectional top view.
25. A triangular prism of base side 50mm and axis 50mm lies on one of its rectangular faces on the
HP with its axis inclined at 30° to the VP.It is cut by a horizontal section plane at a distance of
5mm from the axis. Draw its front view and sectional top view.
26. A square pyramid of base side 40mm and axis 60mm is resting on its base on the HP with a
side of base parallel to the VP.Draw its sectional views and true shape of the section,if it is cut
by a section plane perpendicular to the VP., bisecting the axis and is (a) Parallel to the
HP.,(b)inclined at 45°to the HP.(c)inclined at 60° to the HP.
27. A square pyramid of base side 40mm and axis 60mm is resting on its base on the HP with all
the sides of the base are equally inclined to the VP.Draw its sectional views and true shape of
the section,if it is cut by a section plane perpendicular to the VP bisecting the axis and
is(a)Parallel to the HP(b)inclined at 45° to the HP and (c)inclined at 60° to the HP.
28. A pentagonal pyramid of base side 30mm and axis 60mm is resting on its base in the HP with
an edge parallel to the VP.A horizontal section plane cuts the pyramid bisecting the axis.Draw
its front view and sectional top view.
an edge of the base parallel to the VP.It is cut by a section plane perpendicular to the VP
inclined at 60° to the HP. and bisecting the axis. Draw its front view and sectional top view and
true shape of the section.
30. A pentagonal pyramid of base side 30mm and axis 60mm is on a triangular face in the HP with
its axis parallel to the VP. It is cut by A.I.P inclined at 60° to the HP and passing through the
highest point of the base. Draw its sectional top view and true shape of the section.
A.I.P inclined at 45° to the HP and passing through a point on the axis,20mm above the
base.Draw its sectional top view and obtain true shape of the section.
32. A cone of base diameter 50mm and axis 60mm long is resting on its base on the HP.It is cut by
an A.I.P bisecting the axis inclined at 45° to the HP.Draw its sectional top view and true shape
of the section.
A.I.P parallel to one of the extreme generators passing through a point on the axis 40mm from
its base.Draw its sectional top view and obtain true shape of the section.
34. A cylinder of base diameter 50mm and axis 60mm is resting on its base on the HP.It is cut by a
section plane perpendicular to VP.the VT of which cuts the axis at appoint 40mm from the
bottom face and inclined at 45° to the reference line.Draw its front view ,sectional top view
35. A pentagonal prism of base side 30mm and axis 70mm has an edge of its base on the HP.The
axis is parallel to the VP and inclined at 60° to the HP.It is cut by an A.I.P inclined at 60° to

the HP and passing through the highest corner of the prism. Draw its sectional top view an true
36. A hexagonal prism of base side 30mm and axis 70mm is resting on a face on the HP with axis
parallel to the VP.It is cut by a plane whose VT is inclined at 30° to the reference line and
passes through a point on the axis 20mm from one of its ends.Draw its sectional top view and
obtain true shape of the section.

its rectangular faces is inclined at 30° to the VP.It is cut by a section plane parallel to VP
bisecting a face of the pris which is inclined at 30° to the VP.Draw its sectional front view and
top view.
its rectangular faces is inclined at 30° to the VP.It is cut by a section plane perpendicular to HP
and inclined at 60° to VP passing through the prism such that a face is inclined at 60° to the VP
is bisected.Draw its sectional front view ,top view and true shape of section.
39. A pentagonal prism of base side 30mm and axis 60mm lies on one of its rectangular faces on
the HP.with its axis inclined at 45° to the VP.A vertical section plane parallel to the VP cuts
the prism at a distance of 20mm from one of the end faces. Draw its sectional front view and
top view.
40. A hexagonal prism of base side 30mm and axis 70mm has an edge of its base on the HP with
axis parallel to the VP and inclined at 45° to the HPs.It is cut by an AVP inclined at 45° to the
VP and passing through a point on the axis, 15mm from the top end. Draw its sectional front
view and obtain true shape of the section.
41. A hexagonal prism of base side 30mm and axis 70mm is resting on a face on the ground with
axis parallel to the VP .It is cut by AVP which is inclined at 45° to the VP and passes through a
point 25mm on the axis from one of its ends. Draw its sectional front view and obtain true
a base parallel to VP and nearer to it.It is cut by a section plane parallel to the VP and 12mm in
front of the axis of the pyramid. Draw its sectional front view and top view.
an edge of the base nearer the VP parallel to it. A vertical section plane inclined at 45° to the
VP cuts the pyramid at a distance of 8mm from the axis .Draw its sectional front view top view
44. A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.It is cut by a
section plane whose HT is inclined at 60° to the reference line and passes through a point
15mm away from the axis.Draw its sectional front view and obtain true shape of the section.
45. A pentagonal pyramid of base side 30mm and axis 60mm is resting on a triangular face on the
HP with its axis parallel to the VP.It is cut by a plane whose HT is inclined at 30° to the
reference line and bisects the axis such that the apex is removed.Draw its sectional front view
and obtain true shape of the section.
Section by a plane Perpendicular to Both HP and VP.

46. A square prism of base side 40mm and axis 60mm rests on its base on the HP.Such that one of
its faces is inclined at 30° to the VP.It is cut by a section plane perpendicular to both the HP
and the VP passing through one of the vertical edges.Draw its front view ,top view and
sectional side view.

Development of surfaces
21. A square prism of base side 30mm and axis 60mm is resting on its base on the HP with a
rectangular face parallel to the VP.Draw the development of the prism.
22. A pentagonal prism of base side 30mm and axis 70mm is resting on its base on the HP with a
rectangular face parallel to the VP.It is cut by an auxiliary inclined plane(A.I.P) whose VT is
inclined at 45° to the reference line and passes through the mid-point of the axis .Draw the
development of the lateral surface of the truncated prism.
23. A hexagonal prism of base side 30mm and axis 70mm is resting on its base on the ground with
a side of base inclined at 45° to the VP.It is cut by an auxiliary inclined plane inclined at 45° to
the HP and passes through a point 15mm below the top end of the axis.Draw the development
of the lateral surface of the truncated prism.
24. A hexagonal prism of base side 30mm and height 70mm is resting on its base on the HP with a
side of base perpendicular to the VP.The prism has a cylindrical hole of diameter 40mm,drilled
centrally such that the axis of hole is perpendicular to the VP.Draw the development of the
lateral surface of the prism.
25. Fig shows the front view of a truncated hexagonal prism of base side 30mm and axis
90mm.The prism is resting on the HP with an edge of the base parallel to the VP.Draw the
26. The pentagonal prism of side 30mm rests on its base on the HP.It is cut by A.I.P. inclined at
30° to the HP and passes through the top end of the axis.Also,a cylindrical hole of diameter
40mm is drilled perpendicular to the VP the axis of which is 5mm away from theaxis of the
prism as shown in fig below.Draw the development of its lateral surface.
27. A cylinder of base diameter 50mm and axis 70mm is resting on ground with its axis vertical. It
is cut by a section plane perpendicular to the VP inclined at 45° to the HP passing through the
top of a generator and cuts all the other generators. Draw the development of its lateral surface.
28. A square hole of side 25mm is cut in a cylindrical drum of diameter 50mm and height
70mm.The faces of the hole are inclined at 45° to the HP and axis intersects with that of the
drum at right angles.Draw the development of its lateral surface.
29. Figure shows the front view of a truncated cylinder of diameter 50mm resting on its base on
the HP.Draw the development of its lateral surface.
30. A cylindrical drum of base diameter 50mm and axis 70mm is resting on its base on the HP.A
square hole of side 40mm is cut through the drum such that one of the faces of the square hole
is inclined at 30° to the HP.The axis of the hole is perpendicular to the VP and is 10mm away
from the axis of the cylinder.Draw the development of the retained Cylinder.
31. An object is composed of truncated half-cylinder and half-prism whose projections are given in
Fig.Draw the development of its lateral surface.
33. A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.A section plane
perpendicular to VP and inclined at 45° to HP bisects the axis of the cone.Draw the

35. The frustum of a cone of base diameter 60mm,top diameter 20mm and height 50mm is resting
on its base on the HP.It is cut by an A.I.P inclined at 30° to the HP,the HT of which is
frustum.
36. A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.A square hole
of diagonal 25mm is drilled through it such that axis of the hole intersects the axis of the cone
at a height of 20mm from the base.The faces of the hole are equally inclined to the HP.Draw
the development of its lateral surface.
37. Draw the development of the lateral surface of a square pyramid of base side 40mm and axis
60mm resting on its base on the HP such that (a)all the sides of the base are equally inclined to
the VP and (b)a side of the base is parallel to the VP
a side of the base is parallel to the VP.It is cut by a section plane perpendicular to the VP and
inclined at 45° to the HP bisecting the axis. Draw the development of its lateral surface.
all the sides of the base are equally inclined to the VP.It is cut by a section plane perpendicular
to the VP and inclined at 60° to the HP bisecting the axis. Draw the development of its lateral
surface.
40. A pentagonal pyramid of base side 30mm and axis 60mm rests on its base on the HP with a

UNIT-V
Isometric Projections





TUTORIAL QUESTION PAPER
BATCH-2014
ST PETER’S ENGINEERING COLLEGE

Maisammaguda, secunderabad-500100
I Btech
Common to ALL
Sub: Engineering Graphics
Max marks: 10M Time: 2 hour
Answer any Four of the following questions
1. a) Draw an hyperbola when the distance of its focus from its directrix is 55mm and eccentricity
is 3/2. Also draw a tangent and normal to the hyperbola at a point 30 mm away from the directrix.
b) Two fixed points are 80mm apart. Draw the locus of a point P which moves in a such a way
that the difference of its distance from the fixed points is always the same and equal to 60mm .
2.a)Draw an ellipse when the distance of its focus from its directrix is 55mm and eccentricity is
2/3. Also draw a tangent and normal to the ellipse at a point 70mmaway from the directrix
b) Draw a hypocycloid of a circle dia 50mm , which rolls inside the circle for dia 180mm for
the one revolution also , draw a tangent and normal to the hypocycloid at a point 65mm from
the centre of directing circle
3. a) Draw a hypocycloid of a circle dia 50mm , which rolls outside the circle for dia 180mm for
the one revolution also , draw a tangent and normal to the hypocycloid at a point 65mm from the
centre of directing circle.
b)Construct an ellipse having a major axis 100mm and minor axis 65mm . locate its foci,
directrix and find the eccentricity
4. a) Draw a parabola when the distance between foci and directrix is 50mm .Also draw at tangent
and normal at a point of 70mm from directrix.
b)Inscribe a parabola in a rectangle of sides 100mm and 80mm with the longer side as the base.
locate the focus and directrix of the parabola.
5. a). Draw the projections of the following points on the same reference line(xy line), keeping the
projectors 25mm apart
C. in the V.P. and 40 mm above the H.P.
D. 25 mm below the H.P. and 25 mm behind the V.P.
b)Construct an ellipse having a major axis 100mm and minor axis 65mm . locate its foci, directrix
and find the eccentricity

I Btech
Common to ALL
1)a)A 70mm long line PQ,has its end P 20mm above the HP and 30mm infront of the VP.The line is
inclined at 45° to the HP and 30° to the VP.Draw its projections
b)An 80mm long line AB is inclined at 30° to the HP and 45° to the VP.The end A is 20mm above
the HP and lying in the VP.Draw the projections of the line.
2)a)A straight line PQ has its end P 20mm above the HP and 30mm infront of the VP and the end Q is
b)A line LM 70mm long has its end L 10mm above HP and 15mmin front of VP. Its front and top
HP and VP.
3)A line AB 120mm long is inclined at 45° to the HP and 30° to the VP .Its mid-point C is in VP and
line.
4)a)The distance between the end projectors of a line PQ is 50mm .The end P is 50mm in front of the
b)The top view of 75mm long line PQ measures 50mm.The end P is 15mm above the HP and 50mm

I Btech
Common to ALL
Answer any Two of the following questions
1. A)A pentagonal pyramid of base side 30mm and axis 60mm rests on its base on the HP with a
B) A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.Draw the
2. A)The frustum of a cone of base diameter 60mm,top diameter 20mm and height 50mm is
resting on its base on the HP.It is cut by an A.I.P inclined at 30° to the HP,the HT of which is
frustum.
B) A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.A square
hole of diagonal 25mm is drilled through it such that axis of the hole intersects the axis of the
cone at a height of 20mm from the base.The faces of the hole are equally inclined to the
HP.Draw the development of its lateral surface.
3. A cone of base diameter 100mm and axis 110mm,is resting on its base on the HP.It is
completely penetrated by a cylinder of base diameter 45mm whose axis is parallel to both the
principal planes and 30mm above the HP.The axes of the solids are 10mm apart. Draw the
projections of the combination and show curves of intersection.
4. 4.A) A sphere of 50mm diameter is cut by section plane at a distance of 15mm from its
centre,it is surmounted over the frustum of a square pyramid of base side 60mm,top side 40mm
and height 40mm,draw isometric drawing of arrangement.
B) Draw orthographic front,fop and left side views in first angle projection for given figure.

BATCH-2015

I Btech
Common to ALL

I Btech
Common to ALL
HP and VP.
line.

I Btech
Common to ALL
Answer any Two of the following questions
1.)A) A sphere of 50mm diameter is cut by section plane at a distance of 15mm from its centre,it is
surmounted over the frustum of a square pyramid of base side 60mm,top side 40mm and height
40mm,draw isometric drawing of arrangement.
B) Draw orthographic front,fop and left side views in first angle projection for given figure.
2.)A)A pentagonal pyramid of base side 30mm and axis 60mm rests on its base on the HP with a side
of base parallel to the VP.It is cut by two section plane which meet at a height of 20mm from the base.
One of the section planes is horizontal, while the other is an auxiliary inclined plane whose VT is
inclined at 45° to the HP. Draw the development of the lateral surface of the solid when apex is
removed.
B) A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.Draw the
development of its lateral surface when it is cut by an auxiliary inclined plane inclined at 60° to the HP
and bisecting the axis.
3.)A)The frustum of a cone of base diameter 60mm,top diameter 20mm and height 50mm is resting on
its base on the HP.It is cut by an A.I.P inclined at 30° to the HP,the HT of which is tangential to the
base circle.Draw the development of the lateral surface of the retained frustum.
B) A cone of base diameter 50mm and axis 60mm is resting on its base on the HP.A square hole of
diagonal 25mm is drilled through it such that axis of the hole intersects the axis of the cone at a height
of 20mm from the base.The faces of the hole are equally inclined to the HP.Draw the development of
its lateral surface.
4.)A cone of base diameter 100mm and axis 110mm,is resting on its base on the HP.It is completely
penetrated by a cylinder of base diameter 45mm whose axis is parallel to both the principal planes and
30mm above the HP.The axes of the solids are 10mm apart. Draw the projections of the combination
and show curves of intersection.

BATCH-2016

I Btech I Semester
Common to ME,CE
Answer any two of the following questions
1. a)Draw a epicycloid of a circle dia 50mm , which rolls outside the circle for dia 180mm for the one
revolution also , draw a tangent and normal to the epicycloid at a point 135mm from the centre of
directing circle. (3M)
b)A line MN 50mm long is parallel to VP and inclined at 300 to HP. The end M is 20mm above HP
and 10mm in front of VP. Draw the projections of the line. (2M)
2. a)Construct an ellipse when the distance of the focus from the directrix is equal to 50 mm and
eccentricity is 2/3. (2M)
b) Draw a hypocycloid when the radius of the directing circle is twice the radius of generating
circle and radius of the generating circle is 35 mm. (3M)
3. (a) The front view of a line, inclined at 300 to the V.P. is 65 mm long. Draw the projection of the
line, when it is parallel to and 40 mm above the VP, its one end being 30 mm in front of the V.P. .
(3M)
(b) a) A line CD is parallel to VP and inclined at 400 to HP. C is in HP and 25mm in front of VP.
Top view is 50mm long. Find its true length. (2M)
4 (a). Draw the projections of the following points on the same reference line(xy line), keeping the
projectors 25mm apart (2M)
(b)Construct an ellipse having a major axis 100mm and minor axis 65mm . locate its foci,
directrix and find the eccentricity.(3M)

I Btech I Semester
Common to ME,CE
Answer any two of the following questions
1.A pentagonal prism of base side 30mm and axis 60mm is resting on one of its rectangular faces on
the HP with axis parallel to the VP.Draw its Projections.(5M)
2.A pentagonal prism of base side 30mm and axis 70mm has an edge of its base on the HP.The axis is
parallel to the VP and inclined at 60° to the HP.It is cut by an A.I.P inclined at 60° to the HP and
passing through the highest corner of the prism. Draw its sectional top view an true shape of the
section.(5M)
3. A cylindrical drum of base diameter 50mm and axis 70mm is resting on its base on the HP.A square
hole of side 40mm is cut through the drum such that one of the faces of the square hole is inclined at
30° to the HP.The axis of the hole is perpendicular to the VP and is 10mm away from the axis of the
cylinder.Draw the development of the retained Cylinder.(5M)
4.Draw the orthographic projection of the given isometric solid.(5M)

BATCH-2017

I Btech
Common to ALL

I Btech
Common to ALL
HP and VP.
line.

WEAK LEARNERS AVERAGE LEARNERS AND ADVANCED LEARNERS
AFTER 3 WEEKS
MECHANICAL
ADVANCED AVERAGE WEAK

ROLL NO.
LEARNERS LEARNERS LEARNERS
17BK1A0301 AVG L
17BK1A0302 AVG L
17BK1A0303 AVG L
17BK1A0304 AVG L
17BK1A0305 WEAK L
17BK1A0306 AVG L
17BK1A0307 AVG L
17BK1A0308 AVG L
17BK1A0309 AVG L
17BK1A0310 AVG L
17BK1A0311 AVG L
17BK1A0312 ADV L
17BK1A0313 AVG L
17BK1A0314 ADV L
17BK1A0315 AVG L
17BK1A0316 ADV L
17BK1A0317 AVG L
17BK1A0318 WEAK L
17BK1A0319 AVG L
17BK1A0320 AVG L
17BK1A0321 AVG L
17BK1A0322 AVG L
17BK1A0323 ADV L
17BK1A0324 AVG L
17BK1A0325 AVG L
17BK1A0326 AVG L
17BK1A0327 WEAK L
17BK1A0328 AVG L

17BK1A0329 ADV L
17BK1A0330 AVG L
17BK1A0331 AVG L
17BK1A0332 AVG L
17BK1A0333 ADV L
17BK1A0334 AVG L
17BK1A0335 AVG L
17BK1A0336 WEAK L
17BK1A0337 AVG L
17BK1A0338 AVG L
17BK1A0339 WEAK L
17BK1A0340 WEAK L
17BK1A0341 AVG L
17BK1A0342 AVG L
17BK1A0343 AVG L
17BK1A0344 AVG L
17BK1A0345 AVG L
17BK1A0346 AVG L
17BK1A0347 AVG L
17BK1A0348 WEAK L
17BK1A0349 AVG L
17BK1A0350 AVG L
17BK1A0351 AVG L
17BK1A0352 WEAK L
17BK1A0353 ADV L
17BK1A0354 AVG L
17BK1A0355 WEAK L
17BK1A0356 AVG L
17BK1A0357 AVG L
17BK1A0358 AVG L
17BK1A0359 ADV L
17BK1A0360 AVG L
17BK1A0361 AVG L
17BK1A0362 AVG L
17BK1A0363 WEAK L
17BK1A0364 AVG L
17BK1A0365 AVG L
17BK1A0366 AVG L
17BK1A0367 AVG L
17BK1A0368 AVG L
17BK1A0369 AVG L
17BK1A0370 AVG L
17BK1A0371 ADV L
17BK1A0372 AVG L
17BK1A0373 WEAK L
17BK1A0374 AVG L
17BK1A0375 WEAK L
17BK1A0376 AVG L
17BK1A0377 WEAK L
17BK1A0378 AVG L
17BK1A0379 AVG L
17BK1A0380 ADV L
17BK1A0381 AVG L

AFTER 3 WEEKS
ECE

ROLL NO.
17BK1A0401 ADV L
17BK1A0402 ADV L
17BK1A0403 ADV L
17BK1A0404 ADV L
17BK1A0405 AVG L
17BK1A0406 AVG L
17BK1A0407 AVG L
17BK1A0408 AVG L
17BK1A0409 AVG L
17BK1A0410 AVG L
17BK1A0411 AVG L
17BK1A0412 ADV L
17BK1A0413 WEAK L
17BK1A0414 AVG L
17BK1A0415 AVG L
17BK1A0416 AVG L
17BK1A0417 ADV L
17BK1A0418 AVG L
17BK1A0419 AVG L
17BK1A0420 AVG L
17BK1A0421 AVG L
17BK1A0422 ADV L
17BK1A0423 AVG L
17BK1A0424 ADV L
17BK1A0425 AVG L
17BK1A0426 AVG L
17BK1A0427 AVG L
17BK1A0428 AVG L
17BK1A0429 AVG L
17BK1A0430 ADV L
17BK1A0431 ADV L
17BK1A0432 AVG L

17BK1A0433 ADV L
17BK1A0434 WEAK L
17BK1A0435 ADV L
17BK1A0437 ADV L
17BK1A0438 ADV L
17BK1A0439 ADV L
17BK1A0440 ADV L
17BK1A0441 ADV L
17BK1A0442 AVG L
17BK1A0443 ADV L
17BK1A0444 WEAK L
17BK1A0445 AVG L
17BK1A0446 ADV L
17BK1A0447 ADV L
17BK1A0448 ADV L
17BK1A0449 ADV L
17BK1A0450 ADV L
17BK1A0451 ADV L
17BK1A0452 ADV L
17BK1A0453 AVG L
17BK1A0454 AVG L
17BK1A0455 AVG L
17BK1A0456 AVG L
17BK1A0457 AVG L
17BK1A0458 ADV L
17BK1A0459 ADV L
17BK1A0461 AVG L
17BK1A0462 ADV L
17BK1A0463 ADV L
17BK1A0464 ADV L
17BK1A0465 AVG L
17BK1A0466 ADV L
17BK1A0467 AVG L
17BK1A0468 AVG L
17BK1A0469 WEAK L
17BK1A0470 ADV L
17BK1A0471 ADV L
17BK1A0472 AVG L
17BK1A0473 ADV L

17BK1A0474 AVG L
17BK1A0475 ADV L
17BK1A0476 ADV L
17BK1A0477 ADV L
17BK1A0478 ADV L
17BK1A0479 ADV L
17BK1A0480 AVG L
17BK1A0481 ADV L
17BK1A0482 ADV L
17BK1A0483 AVG L
17BK1A0484 AVG L
17BK1A0485 ADV L
17BK1A0486 WEAK L
17BK1A0487 ADV L
17BK1A0488 WEAK L
17BK1A0489 AVG L
17BK1A0490 ADV L
17BK1A0491 ADV L
17BK1A0492 AVG L
17BK1A0493 ADV L
17BK1A0494 ADV L
17BK1A0495 AVG L
17BK1A0496 WEAK L
17BK1A0497 AVG L
17BK1A0498 AVG L
17BK1A0499 WEAK L
17BK1A04A0 AVG L
17BK1A04A1 WEAK L
17BK1A04A2 AVG L
17BK1A04A4 WEAK L
17BK1A04A5 ADV L
17BK1A04A6 ADV L
17BK1A04A7 AVG L
17BK1A04A8 WEAK L
17BK1A04A9 AVG L
17BK1A04B0 AVG L
17BK1A04B1 ADV L
17BK1A04B2 ADV L
17BK1A04B3 AVG L

17BK1A04B4 WEAK L
17BK1A04B5 WEAK L
17BK1A04B6 AVG L
17BK1A04B7 AVG L
17BK1A04C1 ADV L
17BK1A04C2 AVG L
17BK1A04C3 AVG L
17BK1A04C4 AVG L
17BK1A04C5 AVG L
17BK1A04C6 AVG L
17BK1A04C7 AVG L
17BK1A04C8 AVG L
17BK1A04C9 AVG L
17BK1A04D0 AVG L
17BK1A04D1 AVG L
17BK1A04D2 WEAK L
17BK1A04D3 AVG L
17BK1A04D4 WEAK L
17BK1A04D5 AVG L
17BK1A04D6 AVG L
17BK1A04D7 AVG L
17BK1A04D8 AVG L
17BK1A04D9 ADV L
17BK1A04E0 ADV L
17BK1A04E1 ADV L
17BK1A04E2 AVG L
17BK1A04E3 AVG L
17BK1A04E4 AVG L
17BK1A04E5 AVG L
17BK1A04E6 ADV L
17BK1A04E7 ADV L
17BK1A04E8 AVG L
17BK1A04E9 AVG L
17BK1A04F0 WEAK L
17BK1A04F1 ADV L
17BK1A04F3 AVG L
17BK1A04F4 AVG L
17BK1A04F5 AVG L
17BK1A04F6 AVG L

17BK1A04F7 WEAK L
17BK1A04F8 AVG L
17BK1A04F9 ADV L
17BK1A04G0 AVG L
17BK1A04G1 AVG L
17BK1A04G2 WEAK L
17BK1A04G3 AVG L
17BK1A04G4 AVG L
AFTER 3 WEEKS
CSE

ROLL NO.
17BK1A0501 AVG L
17BK1A0502 AVG L
17BK1A0503 AVG L
17BK1A0504 ADV L
17BK1A0505 AVG L
17BK1A0506 ADV L
17BK1A0507 ADV L
17BK1A0508 WEAK L
17BK1A0509 AVG L
17BK1A0510 WEAK L
17BK1A0511 AVG L
17BK1A0512 WEAK L
17BK1A0513 ADV L
17BK1A0514 WEAK L
17BK1A0515 WEAK L
17BK1A0516 AVG L
17BK1A0517 ADV L
17BK1A0518 WEAK L
17BK1A0519 ADV L
17BK1A0520 AVG L
17BK1A0521 WEAK L
17BK1A0522 ADV L
17BK1A0523 AVG L
17BK1A0524 AVG L

17BK1A0525 WEAK L
17BK1A0526 AVG L
17BK1A0527 WEAK L
17BK1A0529 WEAK L
17BK1A0530 AVG L
17BK1A0531 ADV L
17BK1A0532 AVG L
17BK1A0533 WEAK L
17BK1A0534 ADV L
17BK1A0535 AVG L
17BK1A0536 AVG L
17BK1A0537 WEAK L
17BK1A0538 AVG L
17BK1A0539 AVG L
17BK1A0540 AVG L
17BK1A0541 ADV L
17BK1A0542 ADV L
17BK1A0543 WEAK L
17BK1A0544 ADV L
17BK1A0545 ADV L
17BK1A0546 WEAK L
17BK1A0547 AVG L
17BK1A0548 AVG L
17BK1A0549 AVG L
17BK1A0550 AVG L
17BK1A0551 ADV L
17BK1A0552 ADV L
17BK1A0553 AVG L
17BK1A0554 AVG L
17BK1A0555 ADV L
17BK1A0556 AVG L
17BK1A0557 WEAK L
17BK1A0558 AVG L
17BK1A0559 WEAK L
17BK1A0560 WEAK L
17BK1A0561 WEAK L
17BK1A0562 WEAK L
17BK1A0563 WEAK L
17BK1A0564 AVG L

17BK1A0565 AVG L
17BK1A0566 AVG L
17BK1A0567 WEAK L
17BK1A0568 AVG L
17BK1A0569 AVG L
17BK1A0570 AVG L
17BK1A0571 AVG L
17BK1A0572 WEAK L
17BK1A0573 AVG L
17BK1A0574 AVG L
17BK1A0575 AVG L
17BK1A0576 ADV L
17BK1A0577 ADV L
17BK1A0578 AVG L
17BK1A0579 AVG L
17BK1A0580 AVG L
17BK1A0581 ADV L
17BK1A0582 ADV L
17BK1A0583 AVG L
17BK1A0584 AVG L
17BK1A0585 WEAK L
17BK1A0586 WEAK L
17BK1A0587 WEAK L
17BK1A0588 WEAK L
17BK1A0589 ADV L
17BK1A0590 WEAK L
17BK1A0591 WEAK L
17BK1A0592 AVG L
17BK1A0593 AVG L
17BK1A0594 AVG L
17BK1A0595 WEAK L
17BK1A0596 AVG L
17BK1A0597 AVG L
17BK1A0598 WEAK L
17BK1A0599 AVG L
17BK1A05A0 AVG L
17BK1A05A1 ADV L
17BK1A05A2 AVG L
17BK1A05A3 ADV L

17BK1A05A4 WEAK L
17BK1A05A5 WEAK L
17BK1A05A6 AVG L
17BK1A05A7 ADV L
17BK1A05A8 AVG L
17BK1A05A9 ADV L
17BK1A05B0 ADV L
17BK1A05B1 ADV L
17BK1A05B2 ADV L
17BK1A05B3 AVG L
17BK1A05B4 AVG L
17BK1A05B5 AVG L
17BK1A05B6 AVG L
17BK1A05B7 ADV L
17BK1A05B8 AVG L
17BK1A05B9 WEAK L
17BK1A05C0 WEAK L
17BK1A05C1 ADV L
17BK1A05C2 AVG L
17BK1A05C4 AVG L
17BK1A05C5 ADV L
17BK1A05C6 ADV L
17BK1A05C7 WEAK L
17BK1A05C8 ADV L
17BK1A05C9 AVG L
17BK1A05D0 AVG L
17BK1A05D2 ADV L
17BK1A05D3 ADV L
17BK1A05D4 AVG L
17BK1A05D5 WEAK L
17BK1A05D6 WEAK L
17BK1A05D7 AVG L
17BK1A05D9 AVG L
17BK1A05E0 AVG L
17BK1A05E1 AVG L
17BK1A05E2 AVG L
17BK1A05E3 AVG L
17BK1A05E4 AVG L
17BK1A05E5 AVG L

17BK1A05E6 ADV L
17BK1A05E7 AVG L
17BK1A05E8 AVG L
17BK1A05E9 AVG L
17BK1A05F0 AVG L
17BK1A05F1 WEAK L
17BK1A05F2 AVG L
17BK1A05F3 AVG L
17BK1A05F4 WEAK L
17BK1A05F5 ADV L
17BK1A05F6 ADV L
17BK1A05F7 AVG L
17BK1A05F8 ADV L
17BK1A05F9 ADV L
17BK1A05G0 AVG L
17BK1A05G1 AVG L
17BK1A05G2 AVG L
17BK1A05G3 WEAK L
17BK1A05G4 AVG L
17BK1A05G5 WEAK L
17BK1A05G6 AVG L
17BK1A05G7 AVG L
17BK1A05G8 AVG L
17BK1A05G9 WEAK L
17BK1A05H0 AVG L
17BK1A05H1 ADV L
17BK1A05H2 WEAK L
17BK1A05H3 WEAK L
17BK1A05H4 ADV L
17BK1A05H5 ADV L
17BK1A05H6 WEAK L

AFTER 1ST MID
MECHANICAL

ROLL NO. MARKS
17BK1A0301 AVG L 20
17BK1A0302 AVG L 19
17BK1A0303 AVG L 20
17BK1A0304 AVG L 20
17BK1A0305 WEAK L 15
17BK1A0306 AVG L 19
17BK1A0307 AVG L 19
17BK1A0308 AVG L 19
17BK1A0309 AVG L 20
17BK1A0310 AVG L 20
17BK1A0311 AVG L 20
17BK1A0312 ADV L 25
17BK1A0313 AVG L 20
17BK1A0314 ADV L 21
17BK1A0315 AVG L 20
17BK1A0316 ADV L 24
17BK1A0317 AVG L 20
17BK1A0319 AVG L 20
17BK1A0320 AVG L 20
17BK1A0321 AVG L 19
17BK1A0322 AVG L 19
17BK1A0323 ADV L 24
17BK1A0324 AVG L 20
17BK1A0325 AVG L 20
17BK1A0326 AVG L 19
17BK1A0328 AVG L 19

17BK1A0329 ADV L 23
17BK1A0330 AVG L 20
17BK1A0331 AVG L 20
17BK1A0332 AVG L 19
17BK1A0333 ADV L 23
17BK1A0334 AVG L 20
17BK1A0335 AVG L 20
17BK1A0337 AVG L 20
17BK1A0338 AVG L 20
17BK1A0341 AVG L 20
17BK1A0342 AVG L 20
17BK1A0343 AVG L 20
17BK1A0344 AVG L 20
17BK1A0345 AVG L 20
17BK1A0346 AVG L 20
17BK1A0347 AVG L 18
17BK1A0349 AVG L 17
17BK1A0350 AVG L 20
17BK1A0351 AVG L 20
17BK1A0353 ADV L 24
17BK1A0354 AVG L 20
17BK1A0356 AVG L 20
17BK1A0357 AVG L 20
17BK1A0358 AVG L 18
17BK1A0359 ADV L 24
17BK1A0360 AVG L 20
17BK1A0361 AVG L 17
17BK1A0362 AVG L 20
17BK1A0364 AVG L 17

17BK1A0365 AVG L 19
17BK1A0366 AVG L 19
17BK1A0367 AVG L 19
17BK1A0368 AVG L 20
17BK1A0369 AVG L 20
17BK1A0370 AVG L 19
17BK1A0371 ADV L 21
17BK1A0372 AVG L 19
17BK1A0374 AVG L 20
17BK1A0376 AVG L 20
17BK1A0378 AVG L 20
17BK1A0379 AVG L 18
17BK1A0380 ADV L 24
17BK1A0381 AVG L 20

AFTER 1ST MID
ECE

ROLL NO. LEARNERS LEARNERS LEARNERS MARKS
17BK1A0401 ADV L 21.0
17BK1A0402 ADV L 24.0
17BK1A0403 ADV L 22.0
17BK1A0404 ADV L 22.0
17BK1A0405 AVG L 20.0
17BK1A0406 AVG L 20.0
17BK1A0407 AVG L 20.0
17BK1A0408 AVG L 20.0
17BK1A0409 AVG L 20.0
17BK1A0410 AVG L 20.0
17BK1A0411 AVG L 20.0
17BK1A0412 ADV L 22.0
17BK1A0413 WEAK L
17BK1A0414 AVG L 20.0
17BK1A0415 AVG L 20.0
17BK1A0416 AVG L 20.0
17BK1A0417 ADV L 22.0
17BK1A0418 AVG L 20.0
17BK1A0419 AVG L 20.0
17BK1A0420 AVG L 20.0
17BK1A0421 AVG L 20.0
17BK1A0422 ADV L 22.0
17BK1A0423 AVG L 20.0
17BK1A0424 ADV L 22.0
17BK1A0425 AVG L 17.0
17BK1A0426 AVG L 20.0
17BK1A0427 AVG L 20.0
17BK1A0428 AVG L 20.0
17BK1A0429 AVG L 20.0
17BK1A0430 ADV L 21.0
17BK1A0431 ADV L 21.0

17BK1A0432 AVG L 17.0
17BK1A0433 ADV L 22.0
17BK1A0434 WEAK L
17BK1A0435 ADV L 22.0
17BK1A0437 ADV L 21.0
17BK1A0438 ADV L 21.0
17BK1A0439 ADV L 22.0
17BK1A0440 ADV L 22.0
17BK1A0441 ADV L 22.0
17BK1A0442 AVG L 20.0
17BK1A0443 ADV L 21.0
17BK1A0444 WEAK L 15.0
17BK1A0445 AVG L 19.0
17BK1A0446 ADV L 22.0
17BK1A0447 ADV L 22.0
17BK1A0448 ADV L 22.0
17BK1A0449 ADV L 22.0
17BK1A0450 ADV L 22.0
17BK1A0451 ADV L 22.0
17BK1A0452 ADV L 21.0
17BK1A0453 AVG L 20.0
17BK1A0454 AVG L 20.0
17BK1A0455 AVG L 19.0
17BK1A0456 AVG L 19.0
17BK1A0457 AVG L 16.0
17BK1A0458 ADV L 21.0
17BK1A0459 ADV L 22.0
17BK1A0461 AVG L 19.0
17BK1A0462 ADV L 24.0
17BK1A0463 ADV L 25.0
17BK1A0464 ADV L 25.0
17BK1A0465 AVG L 17.0
17BK1A0466 ADV L 22.0
17BK1A0467 AVG L 18.0
17BK1A0468 AVG L 19.0
17BK1A0469 WEAK L 12.0
17BK1A0470 ADV L 24.0
17BK1A0471 ADV L 24.0
17BK1A0472 AVG L 18.0

17BK1A0473 ADV L 24.0
17BK1A0474 AVG L 16.0
17BK1A0475 ADV L 25.0
17BK1A0476 ADV L 25.0
17BK1A0477 ADV L 25.0
17BK1A0478 ADV L 25.0
17BK1A0479 ADV L 23.0
17BK1A0480 AVG L 19.0
17BK1A0481 ADV L 24.0
17BK1A0482 ADV L 22.0
17BK1A0483 AVG L 19.0
17BK1A0484 AVG L 16.0
17BK1A0485 ADV L 23.0
17BK1A0486 WEAK L 14.0
17BK1A0487 ADV L 21.0
17BK1A0488 WEAK L 14.0
17BK1A0489 AVG L 19.0
17BK1A0490 ADV L 21.0
17BK1A0491 ADV L 21.0
17BK1A0492 AVG L 18.0
17BK1A0493 ADV L 25.0
17BK1A0494 ADV L 23.0
17BK1A0495 AVG L 16.0
17BK1A0496 WEAK L 10.0
17BK1A0497 AVG L 16.0
17BK1A0498 AVG L 19.0
17BK1A0499 WEAK L 14.0
17BK1A04A0 AVG L 19.0
17BK1A04A1 WEAK L 13.0
17BK1A04A2 AVG L 16.0
17BK1A04A5 ADV L 22.0
17BK1A04A6 ADV L 23.0
17BK1A04A7 AVG L 17.0
17BK1A04A9 AVG L 19.0
17BK1A04B0 AVG L 16.0
17BK1A04B1 ADV L 24.0
17BK1A04B2 ADV L 21.0

17BK1A04B3 AVG L 18.0
17BK1A04B4 WEAK L 13.0
17BK1A04B6 AVG L 20.0
17BK1A04B7 AVG L 20.0
17BK1A04C1 ADV L 23.0
17BK1A04C2 AVG L 20.0
17BK1A04C3 AVG L 19.0
17BK1A04C4 AVG L 16.0
17BK1A04C5 AVG L 16.0
17BK1A04C6 AVG L 17.0
17BK1A04C7 AVG L 19.0
17BK1A04C8 AVG L 17.0
17BK1A04C9 AVG L 16.0
17BK1A04D0 AVG L 16.0
17BK1A04D1 AVG L 16.0
17BK1A04D2 WEAK L 14.0
17BK1A04D3 AVG L 17.0
17BK1A04D5 AVG L 18.0
17BK1A04D6 AVG L 16.0
17BK1A04D7 AVG L 18.0
17BK1A04D8 AVG L 18.0
17BK1A04D9 ADV L 21.0
17BK1A04E0 ADV L 24.0
17BK1A04E1 ADV L 23.0
17BK1A04E2 AVG L 17.0
17BK1A04E3 AVG L 18.0
17BK1A04E4 AVG L 19.0
17BK1A04E5 AVG L 20.0
17BK1A04E6 ADV L 24.0
17BK1A04E7 ADV L 21.0
17BK1A04E8 AVG L 17.0
17BK1A04E9 AVG L 17.0
17BK1A04F0 WEAK L 10.0
17BK1A04F1 ADV L 24.0
17BK1A04F3 AVG L 17.0
17BK1A04F4 AVG L 19.0
17BK1A04F5 AVG L 19.0

17BK1A04F6 AVG L 20.0
17BK1A04F8 AVG L 18.0
17BK1A04F9 ADV L 24.0
17BK1A04G0 AVG L 18.0
17BK1A04G1 AVG L 16.0
17BK1A04G2 WEAK L 14.0
17BK1A04G3 AVG L 18.0
17BK1A04G4 AVG L 16.0

AFTER 1ST MID
CSE

ROLL NO. LEARNERS LEARNERS LEARNERS MARKS
17BK1A0501 AVG L 20.0
17BK1A0502 AVG L 16.0
17BK1A0503 AVG L 20.0
17BK1A0504 ADV L 23.0
17BK1A0505 AVG L 20.0
17BK1A0506 ADV L 23.0
17BK1A0507 ADV L 23.0
17BK1A0508 WEAK L 15.0
17BK1A0509 AVG L 17.0
17BK1A0510 WEAK L 14.0
17BK1A0511 AVG L 17.0
17BK1A0512 WEAK L 14.0
17BK1A0513 ADV L 22.0
17BK1A0514 WEAK L 14.0
17BK1A0515 WEAK L 14.0
17BK1A0516 AVG L 18.0
17BK1A0517 ADV L 23.0
17BK1A0518 WEAK L 14.0
17BK1A0519 ADV L 23.0
17BK1A0520 AVG L 19.0
17BK1A0521 WEAK L 14.0
17BK1A0522 ADV L 21.0
17BK1A0523 AVG L 16.0
17BK1A0524 AVG L 17.0
17BK1A0525 WEAK L 14.0
17BK1A0526 AVG L 16.0
17BK1A0527 WEAK L 14.0
17BK1A0529 WEAK L 14.0
17BK1A0530 AVG L 20.0
17BK1A0531 ADV L 21.0
17BK1A0532 AVG L 20.0
17BK1A0533 WEAK L 14.0
17BK1A0534 ADV L 21.0

17BK1A0535 AVG L 16.0
17BK1A0536 AVG L 18.0
17BK1A0537 WEAK L 14.0
17BK1A0538 AVG L 17.0
17BK1A0539 AVG L 16.0
17BK1A0540 AVG L 17.0
17BK1A0541 ADV L 21.0
17BK1A0542 ADV L 23.0
17BK1A0543 WEAK L 14.0
17BK1A0544 ADV L 21.0
17BK1A0545 ADV L 23.0
17BK1A0546 WEAK L 14.0
17BK1A0547 AVG L 20.0
17BK1A0548 AVG L 20.0
17BK1A0549 AVG L 16.0
17BK1A0550 AVG L 19.0
17BK1A0551 ADV L 23.0
17BK1A0552 ADV L 21.0
17BK1A0553 AVG L 20.0
17BK1A0554 AVG L 19.0
17BK1A0555 ADV L 21.0
17BK1A0556 AVG L 20.0
17BK1A0557 WEAK L
17BK1A0558 AVG L 16.0
17BK1A0559 WEAK L 15.0
17BK1A0560 WEAK L 14.0
17BK1A0561 WEAK L 14.0
17BK1A0562 WEAK L 14.0
17BK1A0563 WEAK L 14.0
17BK1A0564 AVG L 20.0
17BK1A0565 AVG L 17.0
17BK1A0566 AVG L 19.0
17BK1A0567 WEAK L 14.0
17BK1A0568 AVG L 19.0
17BK1A0569 AVG L 17.0
17BK1A0570 AVG L 19.0
17BK1A0571 AVG L 19.0
17BK1A0572 WEAK L 15.0
17BK1A0573 AVG L 18.0

17BK1A0574 AVG L 19.0
17BK1A0575 AVG L 17.0
17BK1A0576 ADV L 24.0
17BK1A0577 ADV L 22.0
17BK1A0578 AVG L 18.0
17BK1A0579 AVG L 16.0
17BK1A0580 AVG L 16.0
17BK1A0581 ADV L 25.0
17BK1A0582 ADV L 21.0
17BK1A0583 AVG L 19.0
17BK1A0584 AVG L 17.0
17BK1A0585 WEAK L 14.0
17BK1A0586 WEAK L 14.0
17BK1A0587 WEAK L 14.0
17BK1A0588 WEAK L 14.0
17BK1A0589 ADV L 22.0
17BK1A0590 WEAK L 14.0
17BK1A0591 WEAK L 14.0
17BK1A0592 AVG L 19.0
17BK1A0593 AVG L 16.0
17BK1A0594 AVG L 18.0
17BK1A0595 WEAK L 14.0
17BK1A0596 AVG L 16.0
17BK1A0597 AVG L 17.0
17BK1A0598 WEAK L 14.0
17BK1A0599 AVG L 17.0
17BK1A05A0 AVG L 18.0
17BK1A05A1 ADV L 25.0
17BK1A05A2 AVG L 16.0
17BK1A05A3 ADV L 23.0
17BK1A05A6 AVG L 20.0
17BK1A05A7 ADV L 21.0
17BK1A05A8 AVG L 17.0
17BK1A05A9 ADV L 23.0
17BK1A05B0 ADV L 21.0
17BK1A05B1 ADV L 25.0
17BK1A05B2 ADV L 23.0

17BK1A05B3 AVG L 20.0
17BK1A05B4 AVG L 19.0
17BK1A05B5 AVG L 17.0
17BK1A05B6 AVG L 20.0
17BK1A05B7 ADV L 22.0
17BK1A05B8 AVG L 16.0
17BK1A05C0 WEAK L 14.0
17BK1A05C1 ADV L 22.0
17BK1A05C2 AVG L 18.0
17BK1A05C4 AVG L 19.0
17BK1A05C5 ADV L 24.0
17BK1A05C6 ADV L 22.0
17BK1A05C7 WEAK L 10.0
17BK1A05C8 ADV L 22.0
17BK1A05C9 AVG L 19.0
17BK1A05D0 AVG L 20.0
17BK1A05D2 ADV L 23.0
17BK1A05D3 ADV L 24.0
17BK1A05D4 AVG L 20.0
17BK1A05D7 AVG L 19.0
17BK1A05D9 AVG L 20.0
17BK1A05E0 AVG L 19.0
17BK1A05E1 AVG L 19.0
17BK1A05E2 AVG L 19.0
17BK1A05E3 AVG L 18.0
17BK1A05E4 AVG L 20.0
17BK1A05E5 AVG L 20.0
17BK1A05E6 ADV L 22.0
17BK1A05E7 AVG L 18.0
17BK1A05E8 AVG L 17.0
17BK1A05E9 AVG L 19.0
17BK1A05F0 AVG L 18.0
17BK1A05F2 AVG L 18.0
17BK1A05F3 AVG L 16.0

17BK1A05F5 ADV L 25.0
17BK1A05F6 ADV L 22.0
17BK1A05F7 AVG L 20.0
17BK1A05F8 ADV L 23.0
17BK1A05F9 ADV L 22.0
17BK1A05G0 AVG L 17.0
17BK1A05G1 AVG L 17.0
17BK1A05G2 AVG L 16.0
17BK1A05G4 AVG L 19.0
17BK1A05G6 AVG L 20.0
17BK1A05G7 AVG L 20.0
17BK1A05G8 AVG L 19.0
17BK1A05H0 AVG L 16.0
17BK1A05H1 ADV L 22.0
17BK1A05H2 WEAK L 15.0
17BK1A05H4 ADV L 21.0
17BK1A05H5 ADV L 21.0

RESULT ANALYSIS
2014-Batch
Engg Draw (111AJ) 14BK1A0336 19 37 56 6

Regd No Int Ext Total Cr 14BK1A0337 22 33 55 6
14BK1A0301 18 26 44 6 14BK1A0338 20 36 56 6
14BK1A0302 18 6 24 0 14BK1A0339 18 30 48 6
14BK1A0303 20 26 46 6 14BK1A0340 19 48 67 6
14BK1A0304 17 28 45 6 14BK1A0341 18 45 63 6
14BK1A0305 24 36 60 6 14BK1A0342 20 30 50 6
14BK1A0306 18 32 50 6 14BK1A0343 17 43 60 6
14BK1A0307 17 26 43 6 14BK1A0344 16 31 47 6
14BK1A0308 19 26 45 6 14BK1A0345 24 26 50 6
14BK1A0309 19 41 60 6 14BK1A0346 18 26 44 6
14BK1A0310 17 26 43 6 14BK1A0347 19 32 51 6
14BK1A0311 19 26 45 6 14BK1A0349 18 43 61 6
14BK1A0312 21 29 50 6 14BK1A0350 21 26 47 6
14BK1A0313 21 26 47 6 14BK1A0351 20 34 54 6
14BK1A0314 16 0 16 0 14BK1A0352 18 26 44 6
14BK1A0315 16 26 42 6 14BK1A0353 19 0 19 0
14BK1A0316 19 45 64 6 14BK1A0354 16 26 42 6
14BK1A0317 19 26 45 6 14BK1A0355 16 31 47 6
14BK1A0318 20 37 57 6 14BK1A0356 20 31 51 6
14BK1A0319 16 26 42 6 14BK1A0357 17 36 53 6
14BK1A0320 19 39 58 6 14BK1A0358 16 29 45 6
14BK1A0321 20 35 55 6 14BK1A0359 19 52 71 6
14BK1A0322 20 30 50 6 14BK1A0360 15 0 15 0
14BK1A0323 22 29 51 6 14BK1A0361 16 26 42 6
14BK1A0324 15 26 41 6 14BK1A0362 15 26 41 6
14BK1A0325 19 29 48 6 14BK1A0363 19 30 49 6
14BK1A0326 24 55 79 6 14BK1A0364 16 31 47 6
14BK1A0327 17 27 44 6 14BK1A0365 18 31 49 6
14BK1A0328 17 30 47 6 14BK1A0366 16 31 47 6
14BK1A0329 19 33 52 6 14BK1A0367 16 32 48 6
14BK1A0330 22 26 48 6 14BK1A0368 15 26 41 6
14BK1A0331 18 26 44 6 14BK1A0369 17 34 51 6
14BK1A0332 16 26 42 6 14BK1A0370 16 41 57 6
14BK1A0333 22 37 59 6 14BK1A0371 16 0 16 0
14BK1A0335 21 41 62 6 14BK1A0372 16 38 54 6
14BK1A0373 16 26 42 6

14BK1A0374 16 26 42 6 14BK1A0394 18 52 70 6
14BK1A0375 18 26 44 6 14BK1A0395 16 26 42 6
14BK1A0376 15 26 41 6 14BK1A0396 16 0 16 0
14BK1A0377 16 26 42 6 14BK1A0397 16 38 54 6
14BK1A0378 16 26 42 6 14BK1A0398 16 35 51 6
14BK1A0379 16 26 42 6 14BK1A0399 17 0 17 0
14BK1A0380 16 9 25 0 14BK1A03A0 17 26 43 6
14BK1A0381 15 0 15 0 14BK1A03A1 16 0 16 0
14BK1A0382 17 40 57 6 14BK1A03A2 17 17 34 0
14BK1A0383 21 47 68 6 14BK1A03A3 16 0 16 0
14BK1A0384 16 31 47 6 14BK1A03A4 16 0 16 0
14BK1A0385 16 26 42 6 14BK1A03A5 17 30 47 6
14BK1A0386 16 28 44 6 14BK1A03A6 17 30 47 6
14BK1A0387 16 33 49 6
Total
14BK1A0388 16 12 28 0 Students 104
14BK1A0389 22 54 76 6
14BK1A0390 21 47 68 6 Total Passed 89
14BK1A0391 12 0 12 0 Total Failed 15
14BK1A0392 21 26 47 6
14BK1A0393 23 36 59 6
120
104
100 89
85.57692308
80
60
40
15
20
0
No.of Students Passed Students Failed Students Pass Percentage
Attempted

RESULT ANALYSIS
2015-Batch
Engg Draw (111AJ) 15BK1A0336 15 26 41 6

Regd No Int Ext Total Cr 15BK1A0338 16 10 26 0
15BK1A0301 19 52 71 6 15BK1A0339 14 26 40 6
15BK1A0302 13 43 56 6 15BK1A0340 11 6 17 0
15BK1A0303 16 29 45 6 15BK1A0341 12 30 42 6
15BK1A0304 18 26 44 6 15BK1A0342 22 35 57 6
15BK1A0305 15 32 47 6 15BK1A0343 18 26 44 6
15BK1A0306 13 0 13 0 15BK1A0344 14 0 14 0
15BK1A0307 23 26 49 6 15BK1A0345 17 26 43 6
15BK1A0308 23 44 67 6 15BK1A0346 11 0 11 0
15BK1A0309 16 29 45 6 15BK1A0347 18 30 48 6
15BK1A0310 15 26 41 6 15BK1A0348 19 30 49 6
15BK1A0311 15 26 41 6 15BK1A0349 20 26 46 6
15BK1A0312 17 13 30 0 15BK1A0350 19 32 51 6
15BK1A0313 18 26 44 6 15BK1A0351 17 26 43 6
15BK1A0314 15 26 41 6 15BK1A0352 20 38 58 6
15BK1A0315 16 26 42 6 15BK1A0353 25 34 59 6
15BK1A0316 16 26 42 6 15BK1A0354 18 53 71 6
15BK1A0317 15 26 41 6 15BK1A0355 16 6 22 0
15BK1A0318 24 26 50 6 15BK1A0356 18 30 48 6
15BK1A0319 19 41 60 6 15BK1A0357 17 54 71 6
15BK1A0320 79 79 6 15BK1A0358 13 33 46 6
15BK1A0321 17 26 43 6 15BK1A0359 17 55 72 6
15BK1A0322 17 26 43 6 15BK1A0362 15 43 58 6
15BK1A0323 15 29 44 6 15BK1A0364 22 26 48 6
15BK1A0324 14 26 40 6 15BK1A0365 19 29 48 6
15BK1A0325 15 0 15 0 15BK1A0366 17 26 43 6
15BK1A0326 14 30 44 6 15BK1A0367 15 26 41 6
15BK1A0327 24 31 55 6 15BK1A0368 22 26 48 6
15BK1A0328 14 9 23 0 15BK1A0369 18 26 44 6
15BK1A0329 25 26 51 6 15BK1A0370 17 26 43 6
15BK1A0331 15 29 44 6 15BK1A0372 15 5 20 0
15BK1A0332 16 46 62 6 15BK1A0373 18 26 44 6
15BK1A0333 20 26 46 6 15BK1A0374 17 44 61 6
15BK1A0334 18 31 49 6 15BK1A0375 14 26 40 6
15BK1A0335 14 42 56 6 15BK1A0376 16 10 26 0

15BK1A0377 12 14 26 0 15BK1A0390 17 26 43 6
15BK1A0378 18 26 44 6 15BK1A0391 12 0 12 0
15BK1A0379 17 6 23 0 15BK1A0392 18 38 56 6
15BK1A0380 19 26 45 6 15BK1A0393 19 26 45 6
15BK1A0381 19 35 54 6 15BK1A0394 18 26 44 6
15BK1A0382 20 36 56 6 15BK1A0395 16 0 16 0
15BK1A0383 14 26 40 6 15BK1A0396 14 5 19 0
15BK1A0384 17 26 43 6 15BK1A0397 15 29 44 6
15BK1A0385 16 0 16 0
Total
15BK1A0386 16 9 25 0 Students 91
15BK1A0387 16 31 47 6
15BK1A0388 22 32 54 6 Total Passed 73
15BK1A0389 20 47 67 6 Total Failed 18
100 91
90 80.21978022
80 73
70
60
50
40
30
18
20
10
0
Attempted

RESULT ANALYSIS
2016-Batch
E G (131AF) 16BK1A0336 C 5 4 4
Regd No G GP CR CP 16BK1A0337 B+ 7 4 4
15BK1A0371 F 0 4 0 16BK1A0338 C 5 4 4
16BK1A0301 B 6 4 4 16BK1A0339 C 5 4 4
16BK1A0302 C 5 4 4 16BK1A0340 B 6 4 4
16BK1A0303 B 6 4 4 16BK1A0341 C 5 4 4
16BK1A0304 F 0 4 0 16BK1A0342 F 0 4 0
16BK1A0306 F 0 4 0 16BK1A0343 F 0 4 0
16BK1A0307 F 0 4 0 16BK1A0344 F 0 4 0
16BK1A0308 C 5 4 4 16BK1A0345 F 0 4 0
16BK1A0309 B 6 4 4 16BK1A0346 F 0 4 0
16BK1A0310 C 5 4 4 16BK1A0347 B 6 4 4
16BK1A0311 A 8 4 4 16BK1A0348 F 0 4 0
16BK1A0312 F 0 4 0 16BK1A0349 B+ 7 4 4
16BK1A0313 F 0 4 0 16BK1A0351 F 0 4 0
16BK1A0314 F 0 4 0 16BK1A0352 C 5 4 4
16BK1A0315 C 5 4 4 16BK1A0353 F 0 4 0
16BK1A0316 F 0 4 0 16BK1A0354 B 6 4 4
16BK1A0317 F 0 4 0 16BK1A0355 F 0 4 0
16BK1A0318 B+ 7 4 4 16BK1A0356 F 0 4 0
16BK1A0319 F 0 4 0 16BK1A0357 F 0 4 0
16BK1A0320 C 5 4 4 16BK1A0358 F 0 4 0
16BK1A0321 F 0 4 0 16BK1A0359 A 8 4 4
16BK1A0322 F 0 4 0 16BK1A0360 F 0 4 0
16BK1A0323 C 5 4 4 16BK1A0361 C 5 4 4
16BK1A0324 C 5 4 4 16BK1A0362 F 0 4 0
16BK1A0325 C 5 4 4 16BK1A0363 F 0 4 0
16BK1A0326 C 5 4 4 16BK1A0364 C 5 4 4
16BK1A0327 B 6 4 4 16BK1A0365 B 6 4 4
16BK1A0328 F 0 4 0 16BK1A0366 F 0 4 0
16BK1A0329 C 5 4 4 16BK1A0367 C 5 4 4
16BK1A0330 F 0 4 0 16BK1A0368 C 5 4 4
16BK1A0332 C 5 4 4 16BK1A0369 F 0 4 0
16BK1A0333 F 0 4 0 16BK1A0370 F 0 4 0
16BK1A0334 F 0 4 0 16BK1A0371 C 5 4 4
16BK1A0335 B+ 7 4 4 16BK1A0372 C 5 4 4

16BK1A0373 F 0 4 0 16BK1A0383 C 5 4 4
16BK1A0374 F 0 4 0 16BK1A0384 F 0 4 0
16BK1A0375 C 5 4 4 16BK1A0385 C 5 4 4
16BK1A0376 F 0 4 0 16BK1A0386 C 5 4 4
16BK1A0377 F 0 4 0
Total
16BK1A0378 F 0 4 0 Students 84
16BK1A0379 C 5 4 4
16BK1A0380 C 5 4 4 Total Passed 43
16BK1A0381 B 6 4 4 Total Failed 41
16BK1A0382 F 0 4 0
84
90
80
70
60 51.19047619
43 41
50
40
30
20
10
0
Attempted

RESULT ANALYSIS
2017-Batch
S.No Roll.No Grade 30 17BK1A0330 F

1 17BK1A0301 B 31 17BK1A0331 C
2 17BK1A0302 C 32 17BK1A0332 C
3 17BK1A0303 C 33 17BK1A0333 B+
4 17BK1A0304 F 34 17BK1A0334 B+
5 17BK1A0305 F 35 17BK1A0335 F
6 17BK1A0306 B 36 17BK1A0336 C
7 17BK1A0307 C 37 17BK1A0337 F
8 17BK1A0308 B 38 17BK1A0338 F
9 17BK1A0309 F 39 17BK1A0339 C
10 17BK1A0310 F 40 17BK1A0340 F
11 17BK1A0311 C 41 17BK1A0341 B
12 17BK1A0312 B+ 42 17BK1A0342 B
13 17BK1A0313 B 43 17BK1A0343 C
14 17BK1A0314 B+ 44 17BK1A0344 F
15 17BK1A0315 B 45 17BK1A0345 B
16 17BK1A0316 A 46 17BK1A0346 B
17 17BK1A0317 B 47 17BK1A0347 B
18 17BK1A0318 C 48 17BK1A0348 F
19 17BK1A0319 B 49 17BK1A0349 C
20 17BK1A0320 C 50 17BK1A0350 C
21 17BK1A0321 C 51 17BK1A0351 B+
22 17BK1A0322 C 52 17BK1A0352 F
23 17BK1A0323 B+ 53 17BK1A0353 B+
24 17BK1A0324 B 54 17BK1A0354 F
25 17BK1A0325 B 55 17BK1A0355 F
26 17BK1A0326 B 56 17BK1A0356 C
27 17BK1A0327 F 57 17BK1A0357 A
28 17BK1A0328 B 58 17BK1A0358 F
29 17BK1A0329 A 59 17BK1A0359 B

60 17BK1A0360 B+ 72 17BK1A0372 C
61 17BK1A0361 C 73 17BK1A0373 F
62 17BK1A0362 B+ 74 17BK1A0374 B+
63 17BK1A0363 F 75 17BK1A0375 C
64 17BK1A0364 B+ 76 17BK1A0376 B
65 17BK1A0365 B+ 77 17BK1A0377 C
66 17BK1A0366 B 78 17BK1A0378 B+
67 17BK1A0367 C 79 17BK1A0379 C
68 17BK1A0368 C 80 17BK1A0380 B+
69 17BK1A0369 B 81 17BK1A0381 B
70 17BK1A0370 F Total pass 62
71 17BK1A0371 B Total appeared students 81
90 81
76.54320988
80
70 62
60
50
40
30
19
20
10
0
Attempted

RESULT ANALYSIS YEAR BY YEAR
MECHANICAL RESULT ANALYSIS

No.of students attempted Passed Students Failed Students Pass percentage%
104
91
89
85.58
84
80.22 81
76.54
73
62
51.19
43
41
18 19
15
2014 2015 2016 2017


New

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

New

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

New

Uploaded by

Copyright:

Available Formats

ST.

PETER’S ENGINEERING COLLEGE

Name of the course : ENGINEERING GRAPHICS

Name of the Faculty : S.JABIULLA

Class : I Year B.Tech. I,II – Sem MECH,ECE,CSE

Academic Year : 2017-18

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

Name of the Faculty: S.Jabiulla

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

MISSION OF THE INSTITUTE:

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

PROGRAM SPECIFIC OUTCOMES

 PSO1:To produce engineering professionals capable of synthesizing and

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

B.Tech. I Year II Sem. L /T/P/D/C 2/0/0/4/4

 To provide basic concepts in engineering drawing.

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

GAPS IN THE SYLLABUS - TO MEET INDUSTRY/PROFESSION REQUIREMENTS:

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

WEB SOURCE REFERENCES:

T/R BOOK TITLE/AUTHORS/PUBLICATION

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

1.Engineering Drawing, N.D. Bhatt(T1)

2.Engineering Drawing - Basant, Agrawal, TMH (T2)

1.Engineering Graphics. P I Varghese Tata McGraw Hill Education Pvt. Ltd.(R1)

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

Course Relationship of Course outcomes(CO) to Program Outcomes (PO)

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

C116.2:ORTHOGRPHIC PROJECTIONS,PROJECTION OF POINTS,LINES,PLANES

C116.3 :PROJECTION OF SOLIDS

C116.4: SECTION OF SOLIDS,DEVELOPMENT OF SURFACES

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

C116.6: Transformations and Perspectives

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

DEPARTMENTAL TIME TABLES(H&S)

St. PETER’S ENGINEERING COLLEGE

Department/Program: MEC A/BTECH Class/Semester: I/I

Room No.: T3 Academic Year: 2017-18 Tutorial Room: T3

Date (W.E.F): 31/07/2017

Subject Code Subject Faculty Contact No.

PH103BS EP ENGINEERING PHYSICS T.R.P.MUKHARJI 9642173561

CS104ES CP COMPUTER PROGRAMMING IN C KISHORE REDDY 9703062534

ME105ES EM ENGINEERING MECHANICS RAGHU KUMAR REDDY 9704885854

ME106ES EG ENGINEERING GRAPHICS JABIULLA 9949128690

Activity Faculty Contact No.

NSS RAGHU KUMAR REDDY 9704885854

SPORTS M.S .KIRANMAI 9704944433

LIBRARY T.R.P.MUKHARJI 9642173561

Note:-Tutorial will be taken up by the concern faculty.

Timetable In-charge HOD Timetable Co-Ordinator PRINCIPAL

Maisammaguda,Opp.ForestAcademy, Dhulapally, Near Kompally, Medchal(M), Medchal Dist-500 100.,T.S.INDIA

St. PETER’S ENGINEERING COLLEGE

Department/Program: MEC B/BTECH Class/Semester: I/I