Service Manual: Trinitron Color TV

Self Diagnosis
Supported model
SERVICE MANUAL BG-3S CHASSIS

MODEL COMMANDER DEST. CHASSIS NO. MODEL COMMANDER DEST. CHASSIS NO.
KV-XF29M35 RM-954 OCE SCC-U24A-A
KV-XF29M63 RM-954 India SCC-U22A-A
KV-XF29M93 RM-954 India SCC-U22B-A
TRINITRON ® COLOR TV
KV-XF29M35/XF29M63/XF29M93
RM-954
SPECIFICATIONS
Note
Power requirements 110-240 V AC, 50/60 Hz

Power consumption (W) Indicated on the rear of the TV
Television system B/G, I, D/K, M
Color system PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58
Stereo system NICAM Stereo B/G, I; A2 Stereo (German) B/G
Teletext Language English, Arabic, French KV-XF29M35 only
Channel coverage
B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41
I UHF: B21 to B68 / CATV: S01 to S03, S1 to S41
D/K VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60
CATV: Z1 to Z39, S01 to S03, S1 to S41
M VHF: A2 to A13 / UHF: A14 to A79 /
CATV: A-8 to A-2, A to W+4, W+6 to W+84
˘ (Antenna) 75-ohm external terminal
Audio output 6W + 6W
3D WOOFER 15W
Number of terminal
D (Video) Input: 3 Output: 1 Phono jacks; 1 VP-P, 75 ohms
≥ (Audio) Input: 3 Output: 1 Phono jacks; 500 mVrms
(S Video) Input: 2 Y : 1 Vp-p, 75 ohms,
unbalanced, sync
negative
C : 0.286 Vp-p, 75 ohms
2 (Headphone) Output: 1 Minijack
Picture tube 29 inch
Tube size (cm) 72 Measured diagonally
Screen size (cm) 68 Measured diagonally
Dimension (w/h/d, mm) 794 × 589 × 517
Mass (kg) 54
Design and specifications are subject to change without notice.
CAUTION SAFETY-RELATED COMPONENT WARNING!!

SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON
THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
CARBON PAINTED ON THE CRT, AFTER REMOVING THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
ANODE. THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
–2–
RM-954
TABLE OF CONTENTS
Section Title Page Section Title Page
SELF DIAGNOSIS FUNCTION ................................ 4 5. DIAGRAMS

5-1. Block Diagram ......................................................... 43
1. GENERAL ........................................................................ 8 5-2. Frame Schematic Diagram ...................................... 46
5-3 Circuit Boards Location .......................................... 49
2. DISASSEMBLY 5-4. Schematic Diagrams and Printed Wiring Boards ... 50
2-1. 3D Speaker Box Removal ....................................... 25 (1) Schematic Diagram of A (1/2) Board ...................... 53
2-2. Rear Cover Removal ................................................ 25 (2) Schematic Diagram of A (2/2) Board ...................... 57
2-3. Speaker Removal ..................................................... 25 (3) Schematic Diagrams of C, F, J2 and VM1 Boards . 61
2-4. Chassis Assy Removal ............................................. 25 (4) Schematic Diagrams of B2 and B3 Boards ............. 65
2-5. F Bracket Removal .................................................. 26 (5) Schematic Diagrams of D1, H3 and V1 Boards ..... 73
2-6. Service Position ....................................................... 26 5-5. Semiconductors ........................................................ 77
2-7. Replacement of Parts ............................................... 26
2-7-1. Replacement of Control Button ..................................... 26 6. EXPLODED VIEWS
2-7-2. Replacement of Light Guide .......................................... 26 6-1. Speaker Bracket ....................................................... 80
2-8. D1 Board Removal .................................................. 27 6-2. Chassis ..................................................................... 81
2-9. PWB Holder Removal ............................................. 27 6-3. Picture Tube ............................................................. 82
2-10. Terminal Bracket Removal ...................................... 27 6-4. 3D Speaker ............................................................... 83
2-11. V1 Board Removal .................................................. 27
2-12. H3 Board Removal .................................................. 28 7. ELECTRICAL PARTS LIST ...................................... 84
2-13. A and B3 Boards Removal ...................................... 28
2-14. Picture Tube Removal .............................................. 28
3. SET-UP ADJUSTMENTS
3-1. Beam Landing .......................................................... 30
3-2. Convergence ............................................................. 31
3-3. Focus Adjustment .................................................... 33
3-4. G2 (Screen) and White Balance Adjustments ......... 34
4. CIRCUIT ADJUSTMENT
4-1. Adjustments with Commander ................................ 35
4-2. Adjustment Method ................................................. 36
4-3. Picture Quality Adjustments .................................... 41
4-4. A Board Adjustment After IC003 (Memory)
Replacement ............................................................. 41
4-5. Picture Distortion Adjustment ................................. 42
–3–
RM-954
SELF DIAGNOSTIC FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically
begin to flash.
The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER
lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot
be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past
problems and how often these problems occur.
1. DIAGNOSTIC TEST INDICATORS

When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the
problem. If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.
Diagnostic No. of times Self-diagnostic Probable Detected

Item STANDBY/TIMER display/Diagnostic Cause Symptoms
Description lamp flashes result Location
• Power does not Does not light — • Power cord is not plugged • Power does not come on.
turn on in. • No power is supplied to the
• Fuse is burned out F4601 TV.
(F) • AC power supply is faulty.
• +B overcurrent 2 times 002:000 or • H.OUT Q511 is shorted. (A • Power does not come on.
(OCP) or 002:001~255 board) • Load on power line is
overvoltage 003:001~255 • IC701 is shorted. (C board) shorted.
(OVP) 004:001~255 • -13V is not supplied. (A • Has entered standby state
• Vertical deflection at the same time board) after horizontal raster.
stopped • IC 503 faulty (A board) • Vertical deflection pulse is
• Horizontal stopped.
deflection • Power line is shorted or
overdrive power supply is stopped.
• White balance 5 times 005:000 or • G2 is improperly adjusted. • No raster is generated.
failure (no 005:001~225 (Note 2) • CRT cathode current
PICTURE) • CRT problem. detection reference pulse
• Video OUT IC701 is faulty. output is small.
(C board)
• IC301 is faulty. (A board)
• No connection A board to C
board.
• Micro reset — 101:00 or • Discharge CRT (C Board) • Power is shut down shortly,
101:001~225 • Static discharge after this return back to
• External noise normal.
• Detect Micro latch up.
Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.

The symptom that is diagnosed first by the microcontroller is displayed on the screen.
Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.
–4–
RM-954
2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT
2 times
5 times
Lamp ON 0.3 sec.

Lamp OFF 3 sec.
Lamp OFF 0.3 sec.
STANDBY/SLEEP lamp
Diagnostic Item Flash Count*

+B overcurrent/overvoltage 2 times
Vertical deflection stopped
White balance failure 5 times
* One flash count is not used for self-diagnostic.
3. STOPPING THE STANDBY/TIMER FLASH

Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp
from flashing.
–5–
RM-954
4. SELF-DIAGNOSTIC SCREEN DISPLAY

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it
is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]

In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screen display] / channel [5] / Sound volume [-] / Power ON

˘
Note that this differs from entering the service mode (mode volume [+]).
Self-Diagnosis screen display
SELF DIAGNOSTIC
002 : 000 Numeral "0" means that no fault has been detected.
003 : 000
004 : 000
005 : 001 Numeral "I" means a fault has been detected.
101 : 000
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.
[Clearing the result display]

To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic
screen is being displayed.
Channel [8] / 0
[Quitting Self-diagnostic screen]

To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
–6–
RM-954
6. SELF-DIAGNOSTIC CIRCUIT
IC301 IC001 IC003

Y/CHROMA JUNGLE SYSTEM MEMORY
FROM
21 IK-IN IO-8DAT 45 5 B-DAT
CRT
FROM
MP/
[+B] Q604 C 18 O-LED 51
PROTECT
SDA 35 46 IO-SDAT
[V] Q509/507
[+B overcurrent ªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven
verticals in a period, the unit will automatically turn off.
[Vertical deflection stopped] Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.
[Vertical deflection overcurrent] Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.
[White balance failure] If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301. TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
–7–
The operating instructions mentioned here are partial abstracts SECTION 1
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual. GENERAL
Using Your New TV

WARNING
• Dangerously high voltages are present inside the TV.
• Operate the TV only between 110 – 240 V AC. Getting Started
RM-954
Step 1
Connect the antenna
If you wish to connect a VCR, see the “Connecting a VCR” diagram below.
Do not open the cabinet and the rear cover of the Install the TV in a stable position. Do not allow Rear of TV
TV. Refer servicing to qualified personnel. children to climb onto it.
or
Antenna cable (not supplied)
IEC connector
(not supplied)

–8–
Do not operate the TV if any liquid or solid object : Signal flow

To prevent fire or shock hazard, do not expose falls into it. Have it checked immediately by
the TV to rain or moisture. qualified personnel only. CAUTION
Do not connect the power cord until you have completed making all other
connections; otherwise a minimum leakage current might flow through the antenna
and other terminals to ground.
Connecting a VCR
To watch the video, see page 10.
Rear of TV
Do not install the TV in a confined space, such Clean the TV with a dry and soft cloth.
as a bookcase or built-in cabinet. Do not use benzine, thinner, or any other chemicals Antenna cable (not supplied)
Do not block the ventilation openings of the TV. to clean the TV. Do not scratch the picture tube.
To antenna
output VCR
To ˘
(antenna) WOOFER
(8Ω)
Do not pull the power cord to disconnect the TV. Do not plug in too many appliances to the same
Pull it out by the plug. power socket. Do not damage the power cord.
AUDIO VIDEO
S video cable
VIDEO IN
(not supplied)
VIDEO OUT
To S video To
To video and output (S video input) To … 1 or 2
audio outputs (video input)
Disconnect the power cord during lightning Audio/Video cable (yellow)

storms or if you are not going to use the TV for Do not install the TV in hot, humid or excessively (not supplied) -L (MONO) (white)
several days. dusty places. -R (red)
: Signal flow
2 4 Using Your New TV
Notes
Connecting the 3D WOOFER
• If you connect a monaural VCR, connect the yellow plug to (the yellow
jack) and the black plug to -L (MONO) (the white jack).
• If you connect a VCR to the ˘ (antenna) terminal, preset the signal
output from the VCR to the program number 0 on the TV. You can enjoy high quality sound by connecting the 3D WOOFER.
Using Your New TV

• If both (S video input) and … 1 (video input) at the rear of your TV
are input at the same time, the (S video input) is automatically
3D WOOFER
selected. To view … 1 (video input), disconnect the S video cable. Rear of TV
• When no signal is input to the connected video equipment, the TV screen
becomes blue. 1 2
Step 2 Black wire
Insert the batteries

into the remote
Note
WOOFER
(8 )
Red wire
• Do not use old batteries nor use different types of batteries together.
Step 3
Preset the channels automatically
Front of TV 1 Attach the 3D WOOFER into the footholds on the top of your TV.
–9–
2 Connect the wires to the 3D WOOFER (8Ω) terminals at the rear of your TV.
The red wire should be connected to the ‘ red terminal and the black wire
1 to the ’ black terminal.
PROGR
ONE-PUSH AUTOMATIC PROGRAMMING
AUTO PROGRAM Notes

2 1
AUTO
PROGR PR:01
TV SYS:AUTO • Connect only the supplied 3D WOOFER; otherwise your TV may
VHF LOW malfunction.
• Unplug your TV from the wall outlet when connecting the 3D WOOFER.
Tips • To prevent a malfunction caused by a short circuit of the terminals, make
• If you want to stop the automatic channel presetting, press MENU twice. sure that none of the 3D WOOFER wire strands stick out, making contact
• If your TV has preset an unwanted channel or cannot preset a particular with the neighbouring speaker terminal.
channel, then preset your TV manually (see page 26 and 27).
Now You Are Ready. . .
To preset the channels manually, see
page 26 and 27.
Using Your New TV 5 6 Using Your New TV
RM-954
Connecting optional components Securing the TV
RM-954
You can connect optional audio/video components, such as a VCR, multi disc player, To prevent the TV from falling, secure the TV using one of the following methods:
camcorder, video game or stereo system.
To watch the picture of the connected equipment, see page 10.
Using Your New TV

Connecting a camcorder/video game equipment A With the supplied screws, attach the band to the TV stand and to the rear of
the TV using the provided hole.
using the … (video input) jacks
Front of TV S video cable (not supplied)
or
To Audio/Video cable (not supplied) B Put the cord or chain through the clamps to secure the TV against a wall or
pillar.
(S video To … 3 To video and
input) audio outputs
(video input)
Camcorder
3 or 20
– 10 –
To S video output mm
Video game
equipment 3.8mm
(MONO)
:Signal flow
Notes
• You can also connect video equipment to the … 1 or 2 (video input) jacks
at the rear of your TV.
A B
• If both (S video input) and … 3 (video input) at the front of your TV
are input at the same time, the (S video input) is automatically
selected. To view … 3 (video input), disconnect the S video cable.
Connecting audio/video equipment using the Ú

(monitor output) jacks or
To
antenna Audio system
WOOFER
(8 ) To Ú output
(monitor VCR
output)
or Note
Rear of TV To • Use only the supplied screws. Use of other screws may damage the TV.
To video and
audio inputs audio
inputs
or
(yellow) Audio/Video cable
-L (MONO) (not supplied)
(white) :Signal flow
-R (red)
Note
• When connecting a monaural VCR, connect the yellow plug to (the
yellow jack) and the black plug to -L (MONO) (the white jack).
Watching the TV (continued)
Watching the TV ¤
Additional tasks
This section explains functions used u
while watching TV. Most operations can … To Do this
be done using the remote. ; Turn off temporarily Press u. The u indicator on the TV lights up red.
Using Your New TV

1 2 3
Turn off completely Press U on the TV.
4 5 6 Number buttons
Mute the sound Press ¤.
7 8 9
Watch the video input Press … to select “VIDEO 1”, “VIDEO 2” and
-/-- 0 JUMP (VCR, camcorder, etc.) “VIDEO 3”. To return to the TV program, press ;.
SOUND
Jump back to the previous channel Press JUMP.
MODE SURROUND FAVORITE
Display the on-screen information* Press .

PIC MODE MENU
MENU
A/B ENTER
+/–/ENTER * The picture, sound, and either the program number or video mode are
displayed. The on-screen display for the picture and sound information
u indicator disappears after about 3 seconds.
PROGR +/–
Changing the menu language
. +/–
You can change the menu language as well as the on-screen language.
For details on how to use the menu, see “How to use the menu” on page 20.
1 Press MENU. MENU

– 11 –
1 Press U to turn on the TV.

When the TV is in the
standby mode (the u
indicator on the TV is lit
2 Press + or – to select the
SET UP icon ( ), then
ENTER
red), press u on the remote press ENTER.

or PROGR +/– on the TV.
2 Press PROGR +/– or

number buttons to select 1 2 3 3 Make sure “LANGUAGE/ ” ENTER
the TV program. is selected, then press ENTER.

4 5 6
For double digit numbers,
or
7 8 9
press ÷, then the number
(e.g., for 25, press ÷, then -/-- 0
2 and 5). 4 Press + or – to select
“ ”, then press ENTER.
ENTER
The menu language

3 Press . +/– to adjust the
changes to Arabic.
volume.
To return to the normal screen
Press MENU.
Note (KV-XF25M21/XF25M30/XF29M35 only)
• You can change the menu language as well as the on-screen language
continued between English and Chinese.
RM-954
Advanced Operations
Selecting the
Setting the Wake Up timer SOUND
picture and sound SOUND MODE
RM-954
PIC MODE MENU
1 Press until the

desired period of time
WAKE UP TIMER:10M
modes A/B ENTER
PIC MODE
After 10 minutes
appears.
Using Your New TV

You can select picture and sound modes
and adjust the setting to your preference
WAKE UP TIMER:OFF WAKE UP TIMER:12H00M in PERSONAL option.
No Wake Up Timer After 12 hours
2 Select the TV program or video mode you want to display when you wake
up.
Selecting the picture mode
Press PIC MODE PIC MODE
repeatedly until you get
3 Press u or set the Sleep timer if you want the TV to turn off automatically.
the desired picture mode.
The indicator on the TV lights up orange.
To cancel the Wake Up timer

– 12 –
Press until “WAKE UP TIMER: OFF” appears or turn off the Select To
TV’s main power. DYNAMIC receive high contrast pictures.
Notes STANDARD receive normal contrast pictures.

• The Wake Up timer starts immediately after the on-screen display SOFT receive mild pictures.
disappears.
• If no buttons or controls are pressed for more than two hours after the TV PERSONAL receive the last adjusted picture setting from the ADJUST option
is turned on using the Wake Up timer, the TV automatically goes into the in the A/V CONTROL menu (see page 21).
standby mode. To continue watching the TV, press any button or control
on the TV or the remote.
Selecting the sound mode
Press SOUND MODE ≥ DYNAMIC ≥ DRAMA
Setting the Sleep timer SOUND
repeatedly until you get MODE
Press until the the desired sound mode.

SLEEP TIMER:30M SLEEP TIMER:60M
desired period of time After 30 minutes After 60 minutes ≥ PERSONAL ≥ SOFT
appears.
Select To
SLEEP TIMER:OFF SLEEP TIMER:90M DYNAMIC listen to dynamic and clear sound that emphasizes the low and
No Sleep Timer After 90 minutes high tones.
DRAMA listen to sound that emphasizes voice and high tones.
To cancel the Sleep timer
SOFT receive soft sound.
Press until “SLEEP TIMER: OFF” appears or turn the TV off.
PERSONAL receive the last adjusted sound setting from the ADJUST option
in the A/V CONTROL menu (see page 21).
Tip
• You can also set the picture and sound modes using the menu (see
“Changing the A/V CONTROL setting” on page 21).
Using Your New TV 11 12 Advanced Operations

Viewing your Listening with
favorite channels 1 2 3 surround sound
SOUND
SURROUND
PIC MODE MENU
4 5 6 Number
buttons A/B ENTER
You can display and select six of your The surround feature enables you to
7 8 9
favorite channels directly from your TV enjoy the sound effects of a concert hall
screen. -/-- 0 or movie theater.
SOUND
FAVORITE
PIC MODE MENU
A/B ENTER
Press SURROUND
repeatedly until you
SURROUND: HIGH SURROUND: LOW
receive the desired
1 Press FAVORITE. surround sound. SURROUND
Advanced Operations
FAVORITE
SURROUND: OFF
Select To
2 Press the number button
from 1 to 6 to select the 1 HIGH listen to sound that spreads out over a large area, giving the feeling
– 13 –
desired channel. 1 2 3 of being at a concert hall.
4 5 6 LOW listen to the sound that gives the feeling of being at a live concert.
OFF turn off the surround sound.
Tip
• To program your favorite channels, see “Programming your favorite
channels” on page 23. The surround of your TV is categorized as TruSurround.
TM
is a trademark of SRS Labs, Inc. SRS and the SRS symbol are
registered trademarks of SRS Labs, Inc. in the United States and selected foreign
countries. SRS and TruSurround are incorporated under license from SRS Labs,
Inc. and are protected under United States Patent Nos. 4,748,669 and 4,841,572
with numerous additional issued and pending foreign patents.
Advanced Operations 13 14 Advanced Operations
RM-954
Selecting a stereo SOUND
Selecting a stereo or bilingual program (continued)
or bilingual
When receiving an A2 (German) program
RM-954
PIC MODE MENU
program A/B ENTER

Broadcasting On-screen display (Selected sound)
A/B A2 (German) stereo
MONO STEREO
(Regular sound) (Stereo sound)
You can enjoy stereo sound or bilingual

programs of NICAM and A2 (German)
stereo systems.
A2 (German) bilingual
MAIN SUB
(Main sound) (Sub sound)
Receiving area for NICAM and A2 (German) programs (For KV-XF29M35 only)
– 14 –
Press A/B repeatedly

until you receive the System Receiving area
STEREO
sound you want. b NICAM Hong Kong, Singapore, New Zealand, Malaysia,
Thailand, etc.
The on-screen display changes
to show the selected sound A2 (German) Australia, Malaysia, Thailand, etc.
and the Â indicator on the TV
lights up red.
Notes
• If the signal is very weak, the sound becomes monaural automatically.
• If the stereo sound is noisy when receiving a NICAM program, select
When receiving a NICAM program “MONO”. The sound becomes monaural, but the noise is reduced.
Broadcasting On-screen display (Selected sound)
NICAM stereo If the sound is distorted or noisy when receiving a monaural
NICAM MONO program through the ˘ (antenna) terminal
(Stereo sound) (Regular sound)
Press A/B repeatedly until “MONO” appears on the screen.
To cancel the monaural sound setting, press A/B again until
“AUTO” appears on the screen.
NICAM bilingual
NICAM NICAM MONO MONO AUTO
MAIN SUB (Regular sound)
(Main sound) (Sub sound)
NICAM monaural Notes

NICAM MONO
MAIN
• The “MONO” or “AUTO” setting is memorized for each program
(Regular sound)
(Main sound) position.
• You cannot receive stereo broadcast signal when the TV is in the “MONO”
setting. Normally set the TV to “AUTO.”
continued

Viewing Teletext Viewing Teletext (continued)
(KV-XF29M35 only)
Additional Teletext tasks
…
To Do this
TV stations broadcast an information ;
service called Teletext via some TV display a Teletext page on the TV Press .
1 2 3
channels. Teletext allows you to receive picture Each time you press , the screen changes as
various information, such as shares 4 5 6 follows: Teletext n Teletext and TV n TV.
market or news. 7 8 9 check the contents of a Teletext service Press .
An overview of the Teletext contents and page
-/-- 0
numbers appear on the screen.
SOUND
select a Teletext page Press the number buttons to enter the three-digit
page number of the desired Teletext page.* If you

PIC MODE MENU make a mistake, reenter the correct page number. To
A/B access the next or previous page, press PROGR␣ +/–.
A/B ENTER
hold a Teletext page Press … to display the symbol “j” at the top
(stop the page from scrolling) left corner of the screen. To resume normal Teletext
operation, press … or .
reveal concealed information Press .
(e.g., an answer to a quiz) To conceal the information, press the button again.
Displaying Teletext enlarge the Teletext display Press A/B .
Each time you press A/B , the Teletext display
1 Select a TV channel that carries the Teletext broadcast you want to watch. changes as follows: Enlarge upper half n Enlarge
lower half n Normal size.
– 15 –
2 Press
text.
to display the wait for a Teletext page while watching
a TV program
1 Enter the Teletext page number that you want to
P166 SECTEXT 166 FR1 MAR 03:59:09 refer to, then press .
A Teletext page (normally 2 When the page number is displayed, press to
the index page) is show the text.
b
Fom Singapore
Day Dep/Arr Flight Alrcraft
To PARIS 1.6 220/0588 SQ28 747
2 2130/1225 PA115 L15
displayed. If there is no To OSAKA

3
2.5
4.6
2115/1330
1000/1715
0930/2015
SQ26
SQ6
CX522
747
747
L10
Teletext broadcast, “100” is To ROMA
To SYDNEY
2.7
1
4
2130/0745
2300/0915
2210/0610
SQ24
AZ487
SQ21A
747
747
747
* You can also select a Teletext page of any page number that appears in the
displayed at the top left 2 2100/0835 SQ21A 747
colored column at the bottom of the screen using the corresponding color-
corner of the screen. coded button on the remote.
To turn off Teletext Using FASTEXT

Press ;. This feature allows you to quickly access a Teletext page that uses
FASTEXT. When a FASTEXT program is broadcasted, the colored
menus appear at the bottom of the screen. The colors of the menus
correspond to the red, green, yellow, and blue color-coded buttons
on the remote.
To access a FASTEXT menu
Press the color-coded button on the remote corresponding to the
menu you want. The menu page appears on the screen after several
seconds.
continued
RM-954
Adjusting Your Setup (MENU)
Introducing the menu system How to use the SOUND

menu
RM-954
PIC MODE MENU
The MENU button lets you open a menu and change the settings of your TV. Here's MENU
an overview of the menu system. A/B ENTER
+ / – /ENTER
You can use the buttons on the remote
Return icon and on the TV as well to display the
Name of the current
A/V CONTROL icon menu menu and adjust the settings.
SET UP icon
CH PRESET icon
Menu level 3
1 Press MENU to display the
menu.
MENU
Menu level 1 Menu level 2
Level 1 Level 2 Level 3/Function

A/V CONTROL PICTURE MODE Select the picture mode.
DYNAMIC n STANDARD n SOFT n 2 Press + or – to select the
desired item.
PERSONAL n ADJUST
ADJUST Adjust the PERSONAL option.
– 16 –
PICTUREnCOLORnBRIGHTnHUEnSHARP
SOUND MODE Select the sound mode.
DYNAMIC n DRAMA n SOFT n
PERSONAL n ADJUST 3 Press ENTER to confirm
your option and go to the
ENTER
ADJUST Adjust the PERSONAL option. next menu level.

BASSnTREBLEnBALANCEnBBE*
Adjusting Your Setup (MENU)

SURROUND Select the surround mode.
HIGHn LOWnOFF
SET UP LANGUAGE Change the menu language. Other menu operations
ENGLISH - (Chinese) or (Arabic) To Press
CHILD LOCK Lock the channel independently. Adjust the setting value +/–
PIC ROTATION Adjust the picture position. Return to the previous menu level* ENTER
FAVORITE CH Program favorite channels. Cancel the menu MENU
INTELLIGENT VOL Adjust volume automatically.
* To return from Menu Level 2 to Level 1, press + / – to select the return
CH PRESET AUTO PROGRAM Preset channels automatically. icon ( ), then press ENTER.
MANUAL PROGRAM Preset channels manually.
Tips
SKIP Skip unwanted or unused program positions.
• If more than 60 seconds elapse between entries, the menu screen
TV SYS Select the TV system. disappears.
B/Gn In D/Kn M • You can also use the buttons on the TV for menu operations ¸ +/– work
as + /– on the remote and … works as ENTER on the remote.
COL SYS Select the color system.
AUTOnPALnSECAMnNTSC3.58nNTSC4.43 Front of TV
* The BBE is manufactured by Sony Corporation under license from BBE

Sound, Inc. It is covered by U.S. Patent No. 4,638,258 and No. 4,482,866. PROGR
The word “BBE” and the BBE symbol are the trademarks of BBE Sound, ONE-PUSH AUTOMATIC PROGRAMMING
Inc.
Adjusting Your Setup (MENU) 19 20 Adjusting Your Setup (MENU)

Changing the A/V SOUND
Changing the A/V CONTROL setting (continued)
CONTROL setting PIC MODE MENU
MENU
Adjusting the ADJUST options under PICTURE MODE
1
A/B
Press + or – to select the
ENTER
+ / – /ENTER ENTER
The A/V CONTROL menu allows you desired item (e.g., COLOR),
to change the picture and sound then press ENTER. COLOR 80
settings.
2 Adjust the value according to the following table, then press ENTER.
For Press – to Press + to
1 Press MENU.
PICTURE decrease picture contrast increase picture contrast
2 Make sure the A/V

CONTROL icon ( ) is
ENTER COLOR decrease color intensity increase color intensity
BRIGHT darken the picture brighten the picture
selected, then press
ENTER. HUE* increase red picture tones increase green picture tones
SHARP soften the picture sharpen the picture
3 Press + or – to select either

PICTURE MODE, SOUND
ENTER * You can adjust HUE for the NTSC color system only.
MODE, or SURROUND,
then press ENTER. 3 Repeat the above steps to adjust other items.
The adjusted settings will be received when you select PERSONAL.

– 17 –
desired option, then press

ENTER Adjusting the ADJUST options under SOUND MODE
ENTER.
desired item (e.g., BALANCE),
ENTER
BALANCE 00
then press ENTER.
For Select
PICTURE MODE either DYNAMIC, STANDARD, SOFT, PERSONAL*, or ADJUST. 2 Adjust the value according to the following table, then press ENTER.
SOUND MODE either DYNAMIC, DRAMA, SOFT, PERSONAL*, or ADJUST. For Press – to Press + to
SURROUND either HIGH, LOW, or OFF. BASS decrease the bass increase the bass
* When the PERSONAL mode is selected, the last adjusted picture
and sound settings from the ADJUST option are received (see TREBLE decrease the treble increase the treble
next page). BALANCE increase the left speaker’s volume increase the right speaker’s volume
BBE select “HIGH” for higher enhancement of sound clarity;
select “LOW” for lower enhancement of sound clarity;
Tip
select “OFF” to turn off the BBE sound
• For details on the options under “PICTURE MODE”, “SOUND MODE”
and “SURROUND”, see page 12 and 14 respectively.
3 Repeat the above steps to adjust other items.
The adjusted settings will be received when you select PERSONAL.
Press MENU. Tip
• For details on the menu system and how to use the menu, refer to “Introducing
continued the menu system” on page 19 and “How to use the menu” on page 20.
RM-954
Changing the SET Changing the SET UP setting (continued)
1 2 3
UP setting Using the CHILD LOCK feature
RM-954
Number
4 5 6
buttons You can prevent your children from watching certain programs by
The SET UP menu allows you to change 7 8 9 using the CHILD LOCK feature.
the menu language, lock channels,
-/-- 0
adjust the picture position, program
your favorite channels and adjust SOUND
1 Press MENU.
volume automatically. MODE SURROUND FAVORITE
PIC MODE MENU

MENU 2 Press + or – to select the
ENTER
A/B ENTER
+ / – / ENTER
press ENTER.
Programming your favorite channels
The FAVORITE CH feature enables you to program up to six
channels for direct selection.
3 Press + or – to select CHILD
LOCK, then press ENTER. ENTER
1 Press MENU.
– 18 –

ENTER
press ENTER. 4 Press + or –, or number

buttons to select the
ENTER
desired channel, then

press ENTER.
3 Press + or – to select
FAVORITE CH, then press
ENTER or
1 2 3 ENTER
ENTER twice.
4 5 6
7 8 9
4 Press + or –, or number
buttons to program the
ENTER -/-- 0
desired channel (e.g.,

PR03), then press ENTER.
or
5 Press + or – to select “ON”, then
press ENTER.
1 2 3 ENTER
The lock symbol ( )
4 5 6 appears on the screen.
7 8 9 To unlock the channel,
-/-- 0 select “OFF”.
5 To continue programming other favorite channels, press + or – and then 6 To continue locking other channels, press ENTER and then repeat step 4 to 5.
press ENTER. After that, repeat step 4.
To return to the normal screen Press MENU.
Press MENU. continued

Changing other SET UP menu options Changing the
Channel Preset
SOUND
1 Press MENU.
PIC MODE MENU
(CH PRESET) MENU

+ / – /ENTER
2
A/B ENTER
Press + or – to select the ENTER
SET UP icon ( ), then setting

press ENTER.
The CH PRESET menu allows you to
adjust the setup of your TV. For
desired option (e.g.,
ENTER example, you can receive a channel with
a weak signal that fails to be tuned in by
INTELLIGENT VOL), then automatic presetting.
press ENTER.
Presetting channels manually

Select To
LANGUAGE Change the menu language (see “Changing the menu 1 Press MENU.
language” on page 10).
CHILD LOCK Prevent children from watching certain programs (see
“Using the CHILD LOCK feature” on page 24).
CH PRESET icon ( ), then
ENTER
press ENTER.
PIC ROTATION Adjust the picture position when it is not aligned to the
TV screen.
– 19 –
Press + or – to adjust the picture position, then press ENTER.
ENTER 3 Press + or – to select

MANUAL PROGRAM, then ENTER
press ENTER.
PIC ROTATION
FAVORITE CH Program channels for direct selection (see “Programming

your favorite channels” on page 23).
INTELLIGENT VOL Adjust the volume of each TV program automatically. 4 Select the program
number to which you
Press + or – to select “ON”, then press ENTER.
To turn off the Intelligent Volume function, select “OFF”, want to preset a channel.
then press ENTER. (1) Make sure “PR” is ENTER
selected , then press

ENTER.
To return to the normal screen.
Press MENU. (2) Press + or – until the
program number you
ENTER
Note (KV-XF29M35 only) want to preset (e.g.,
• You can change the menu language as well as the on-screen language program number 10)
between English and Chinese.
appears on the menu,
Tip then press ENTER.
• For details on the menu system and how to use the menu, refer to
“Introducing the menu system” on page 19 and “How to use the menu”
on page 20.
RM-954
Changing the Channel Preset (CH PRESET) setting (continued)
5 7 If you are not satisfied
RM-954
Select the desired
channel. with the picture and
sound quality, you may
(1) Press + or – to select ENTER
improve them by using
either VHF LOW, VHF
fine tuning.
HIGH or UHF, then
press ENTER. ENTER
(1) Press + or – to select
FINE, then press
ENTER.
(2) Press + or – until the
desired channel ENTER
picture appears on (2) Press + or – to select ENTER
the TV screen, then MANUAL, then press

press ENTER. ENTER.

picture and sound
6
– 20 –
If the sound of the quality are optimal,

ENTER
desired channel is then press ENTER.

abnormal, select the
appropriate TV system. The + or – icon on the
menu flashes while
tuning.
(1) Press + or – to select ENTER
TV SYS, then press
ENTER.
Press MENU.
sound becomes ENTER
Note
normal (e.g., M), then
• The TV system (TV SYS) and the fine tuning (FINE) settings are
press ENTER. memorized for each program number.
continued

Additional Information
Changing other CH PRESET menu options Self-diagnosis

function
1 Press MENU.
Your TV is equipped with a self-diagnosis function. If there is a

CH PRESET icon ( ), then
ENTER
problem with your TV, the u indicator flashes red. The number of
times the u indicator flashes indicates the possible causes.
press ENTER.
Front of TV

desired option (e.g., SKIP), ENTER
then press ENTER.
Select To
AUTO PROGRAM preset channels automatically.
MANUAL PROGRAM preset channels manually. See “Presetting channels
manually” on page 26 and 27.
TV SYS select the TV system. See “Presetting channels manually” u indicator
on page 27.
– 21 –
COL SYS select the color system. Normally, set this to “AUTO”.
SKIP skip unwanted or unused program numbers.
1 Press + or – until the unused or unwanted program
number appears, then press ENTER.
1 Check that the u indicator flashes red a number of times between 3 second
intervals.
2 Press + or – to select “ON”, then press ENTER.
To put the skipped program number back on, select
“OFF”, then press ENTER. 2 Count the number of times the u indicator flashes.
3 Press U (main power) to turn off your TV.
Tip
• For details on the menu system and how to use the menu, refer to 4 Inform your nearest Sony service center about the number of times the
u indicator flashes.
“Introducing the menu system” on page 19 and “How to use the menu”
on page 20. Be sure to note the model name and serial number located on the rear of
your TV.
Note
• If you preset a locked channel, that particular channel will be unlocked
automatically.
Adjusting Your Setup (MENU) 29 30 Additional Information
RM-954
Troubleshooting Troubleshooting (continued)
RM-954
If you find any problem while viewing your TV, please check the following guide. If Symptom Solutions Possible cause
any problem persists, contact your Sony dealer . Good picture • Press ¸ + to increase the volume level. • The volume level is too
Symptom Solutions Possible cause low.
Snowy picture • Check the antenna cable and connection • Connection is loose or the • Press ¤ to cancel the muting. • The sound is muted.
on the TV, VCR and on the wall. cable is damaged.
• Press A/B until a good sound is • Broadcast signal has a
(page 4)
heard. transmission problem.
No sound
• Display the CH PRESET menu and • Channel presetting is
select “MANUAL PROGRAM” to inappropriate or
Noisy sound preset the channel again. (page 26) incomplete.
• Check the antenna type (VHF/UHF). • The antenna type is
inappropriate. Dotted lines or stripes • Do not use a hair dryer or other • There is local interference
Contact a Sony dealer for advice.
equipment near the TV. from cars, neon signs, hair
• Adjust the antenna direction. Contact a • The antenna direction is dryers, power generators,
Sony dealer for advice. inappropriate. • Adjust the antenna direction for etc.
minimum interference. Contact a Sony
• Try using a booster. • Signal transmission is low. dealer for advice.
– 22 –
Distorted picture • Turn off or disconnect the booster if it is • Broadcast signals are too Double images or • Use a highly directional antenna. • Broadcast signals are
in use. strong. “ghosts” • Use the fine tuning (FINE) function. reflected by nearby
(page 28) mountains or buildings.
• Adjust the antenna direction. Contact a • The antenna direction is

Sony dealer for advice. inapproprite.
Noisy sound
• Turn off or disconnect the booster if it is • Use of a booster is
in use. inappropriate.
No color • Display the A/V CONTROL menu and • The color level setting is
select “ADJUST” of PICTURE MODE, too low.
Good picture • If the sound of all the channels are • The TV system (TV SYS)
noisy, display the CH PRESET menu setting or Channel then adjust the COLOR level. (page 21
and check the TV system (TV SYS) presetting is inappropriate and 22)
setting (page 27), then select “AUTO or incomplete. • Display the CH PRESET menu and • The color system setting is
PROGRAM” to preset the channels check the color system (COL SYS) inappropriate.
again (page 29). setting (usually set this to AUTO).
Noisy sound • If the sound of some channels are noisy, (page 29)
Additional Information
select the channel, then display the CH

PRESET menu and select the • Adjust the antenna direction. Contact a • The antenna direction is
appropriate TV system (TV SYS). Sony dealer for advice. inapproriate.
(page 27) Abnormal color patches • Keep external speakers or other • There are magnetic effects
• Check the power cord, antenna and the • The power cord, antenna electrical equipment away from the TV. from external speakers or
No picture
VCR connections. or VCR is not connected. Do not move the TV while the TV is other electrical equipment
turned on. Press U (main power) on the that may affect the TV.
• Press u (power). • The TV is not turned on. TV to turn off the TV for about five
• The direction of the earth’s
• Press U (main power) on the TV to turn minutes, then turn it on again.
magnetic field may affect
off the TV about five seconds, then turn
the TV.
No sound it on again.
TV cannot receive stereo • Press A/B until “AUTO” appears on • The stereo reception
broadcast signal. the screen. setting is inappropriate.
continued
Additional Information 31 32 Additional Information

Identifying parts and controls
Symptom Solutions Possible cause Refer to the pages indicated in parentheses ( ) for details.
Stereo broadcast sound • Check the antenna cable and connection • Connection is loose or the
switches on and off or is
Front panel
on the TV, VCR and on the wall. (page 4) cable is damaged.
distorted.
• Adjust the antenna direction. Contact a • The antenna direction is
or Sony dealer for advice. inappropriate.
The sound switches
• Press A/B until a good sound is • Broadcast signal has a
between monaural and
heard. transmission problem.
stereo frequently.
“100” appears on the top • The channel carries no

of the screen and no Teletext broadcast.
Teletext display. —
(KV-XF29M35 only)
PROGR
Teletext display is • Check the antenna cable and connection • Connection is loose or the
incomplete on the TV, VCR and on the wall. (page 4) cable is damaged.
(picture snowy or double
images). • Adjust the antenna direction. Contact a • The antenna direction is
(KV-XF29M35 only) Sony dealer for advice. inappropriate.
• Try using a booster. • Signal transmission is too
• Use the fine tuning (FINE) function. low.
– 23 –
(page 28)
1 U (main power) button (9)
Picture slant • Display the SET UP menu and adjust • The terrestrial magnetism
“PIC ROTATION” so that the picture is affects your TV set. 2 AUTO PROGR (program) button (5)
aligned to the TV screen. (page 25) 3 MENU button (20)
4 PROGR +/– (program) buttons (9)
5 ¸ +/– (volume) buttons (9)
• Use the fine tuning (FINE) function. • The interference from
Lines moving across the 6 … (TV/video) button (10)
TV screen. (page 28) external sources, e.g.,
heavy machineries, nearby 7 2 (headphone) jack
broadcast station.
The u indicator on your • Contact your nearest Sony service • Your TV may need service.
TV flashes red a number center.
of times between
3 second intervals.
TV cabinet creaks. • Changes in room

temperature sometimes
make the TV cabinet
— expand or contract,
making a noise. This does
not indicate a malfunction.
A “boom” sound is heard • The TV’s demagnetizing

when the TV is turned on. function is working. This
— does not indicate a
malfunction.
Additional Information 33 34 Additional Information
RM-954
Remote Control
RM-954
3
4 !¶
5
1 2 3 1 2 3
4 5 6 6 4 5 6
7 8 9 7 8 9
-/-- 0 7 -/-- 0
!£
!¢
!∞
SOUND SOUND
MODE SURROUND FAVORITE MODE SURROUND FAVORITE
PIC MODE MENU PIC MODE MENU !§

A/B ENTER
8 A/B ENTER
!º
!¡ 9
– 24 –
!™
1 ¤ (muting) button (10) !£ SOUND MODE button (12)

2 (display) button (10) !¢ SURROUND button (14)
3 u (power) button (9) !∞ FAVORITE button (13)
4 … (video) button (10) !§ PIC MODE button (12)
5 ; (TV) button (10) !¶ Teletext operation buttons (17, 18)
6 Number buttons (9) (KV-XF29M35 only)
7 JUMP button (10) (text) (enlarge)
8 Menu operation buttons (20) (reveal) (hold)
MENU button (index) (text clear)
+ or – buttons p (FASTEXT: red, green, yellow, blue)
ENTER button
9 PROGR +/– button (9)
!º A/B button (15) Names/symbols of buttons on the
!¡ Timer setting buttons (11) remote are indicated in different
(wake up timer) colors to represent the available
(sleep timer) functions.
!™ . (volume) +/– buttons (9) Label color Button function
White For general TV operations
Green For Teletext operations
Additional Information 35
SECTION 2
DISASSEMBLY
2-1. 3D SPEAKER BOX REMOVAL 2-3. SPEAKER REMOVAL

1 3D Speaker box assy
1 Four screws (Washer head)

(+P 4 × 16)
Red wire
2 Bracket, speaker
– 25 –
Black wire
2-2. REAR COVER REMOVAL 2-4. CHASSIS ASSY REMOVAL
2 Rear cover
1 One screw
(+BVTP 4 × 16)
1 Three screws
(+BVTP 4 × 16) 1 Chassis assy
1 Eight screws
RM-954
(+BVTP 4 × 16)
2-5. F BRACKET REMOVAL 2-7. REPLACEMENT OF PARTS
4 Two screws For replacement of the Control Button and Light Guide, unscrew them, exchange
(+BVTP 3 × 12) with the new parts, and fix them with screws (+BVTP) respectively.
5 F bracket
2-7-1. REPLACEMENT OF CONTROL BUTTON
Control button
2 Two claws
6 Two screws
RM-954
(+BVTP 3 × 12)
3 F board
1 Three connectors
Two screws
(+BVTP 3 × 12)
– 26 –
2-6. SERVICE POSITION 2-7-2. REPLACEMENT OF LIGHT GUIDE

(Note: Remove F Bracket first.)
One screw
(+BVTP 3 × 12)
2-8. D1 BOARD REMOVAL 2-10. TERMINAL BRACKET REMOVAL
1 Three connectors
1 Two screws
(+BVTP 3 × 12)
3 D1 board
2 Two claws
3 Terminal bracket
2 One claw
– 27 –
2-9. PWB HOLDER REMOVAL (KV-XF29M35 ONLY) 2-11. V1 BOARD REMOVAL (KV-XF29M35 ONLY)
2 Two screws 2 V1 board

(+BVTP 3 × 12)
PWB holder
1 Two claws
RM-954
2-12. H3 BOARD REMOVAL 2-14. PICTURE TUBE REMOVAL
6 One screw (+BVTP 3 × 12 with washer) NOTE : The picture tube for OCE model is upside-down, and the position for the
anode-cap and tension spring is changed accordingly.
3 Two connectors !¡ Four DGC clip
!™ Demagnetic coil
2 Four connectors
5 H3 Board 0 Four claws
RM-954
6 Chassis assy
1 Two connectors
1 Four screws
(washer head)
7 C board
(+P 4 × 16)
4 Four claws
8 Neck assy !£ Tension
spring
9 Deflection
yoke
!¢ Two screws
– 28 –
(Tapping)
!¢ Two screws
(Tapping)
3 Four screws
2 Speaker Bracket (washer head)
2-13. A AND B3 BOARDS REMOVAL assy (L) (+P 4 × 16)
2 Three screws
(+BVTAP 3 × 12)
1 Two screws
(+BVTAP 3 × 12)
5 Anode cap
4 B3 Board
4 Speaker Bracket
assy (R)
3 Five connectors
5 A Board !∞ Picture tube Cushion

• REMOVAL OF ANODE-CAP
NOTE : After removing the anode, short circuit the anode of the picture tube and
the anode cap to the metal chassis, CRT shield or carbon paint on the
CRT.
• REMOVING PROCEDURES
1 Turn up one side of the rubber cap in the direction indicated by the arrow a.
b
b
2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.
– 29 –
Anode button
3 When one side of the rubber cap is separated from the anode button, the anode-cap
can be removed by turning up the rubber cap and pulling it up in the direction of the
arrow c.
HOW TO HANDLE AN ANODE-CAP
1 Do not damage the surface of anode-caps with sharp shaped objects.
2 Do not press the rubber too hard so as not to damage the inside of anode-cap.
A metal fitting called the shatter-hook terminal is built into the rubber.
3 Do not turn the foot of rubber over too hard.
The shatter-hook terminal will stick out or damage the rubber.
RM-954
RM-954 SECTION 3
SET-UP ADJUSTMENTS
• The following adjustments should be made when a complete Perform the adjustments in the following order :
realignment is required or a new picture tube is installed. 1. Beam Landing
• These adjustments should be performed with rated power 2. Convergence
supply voltage unless otherwise noted. 3. Focus
4. White Balance
Controls and switches should be set as follows unless otherwise noted: Note : Test Equipment Required.
PICTURE control ........................................................... normal 1. Color-bar/Pattern Generator
BRIGHTNESS control ................................................... normal 2. Degausser
3. Oscilloscope
................................................................................................................................................................................................................................
Purity control
Preparation :
• In order to reduce the influence of geomagnetism on the set's
picture tube, face it east or west.
• Switch on the set's power and degauss with the degausser.
3-1. BEAM LANDING

1. Input a white signal with the pattern generator.
Contrast
Brightness } normal Fig. 3-3
2. Position neck assy as shown in Fig3-2.

3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the purity
Blue
control so that the green is at the center and the blue and the red
Red
take up equally sized areas on each side.
(See Figures 3-1 through 3-4.) Green
5. Move the deflection yoke forward and adjust so that the entire
screen is green. (See Figure 3-2.)
6. Switch the raster signal to blue, then to red and verify the Fig. 3-4
condition.
7. When the position of the deflection yoke has been decided,
fasten the deflection yoke with the screws and DY spacers. Purity control
corrects this area.
8. If the beam does not land correctly in all the corners, use a Disk magnets or rotatable
magnet to adjust it. disk magnets correct these
areas (a-d).
(See Figure 3-5.) b a
Neck assy c d
Deflection yoke positioning

corrects these areas.
Behind the G2 edge b
a
G1 G2 G3
d
Fig. 3-1 Fig. 3-2
Fig. 3-5
– 30 –
RM-954
3-2. CONVERGENCE
Preparation :
• Before starting this adjustment, adjust the focus, horizontal size
and vertical size.
• Minimize the brightness setting. Purity BMC
• Provide dot pattern.
BMC (Hexapole)
(1) Horizontal and Vertical Static Convergence Purity
Center dot
R
G
B
R G B
V. STAT
H. STAT VR Magnet
DY pocket
V.STAT
V.STAT
RV702
H. STAT
1 V. STAT
a b
C Board a
B B
b b
1. (Moving horizontally), adjust the H.STAT control so that the G G
red, green and blue dots are on top of each other at the center of R R
the screen.
2. (Moving vertically), adjust the V.STAT magnet so that the red,
2 H. STAT VR
green and blue dots are on top of each other at the center of the a b
screen.
3. If the H.STAT variable resistor cannot bring the red, green and
R G B B G R
blue dots together at the center of the screen, adjust the
horizontal convergence with the H.STAT variable resistor and
the V.STAT magnet in the manner given below.
(In this case, the H.STAT variable resistor and the V.STAT
magnet influence each other, so be sure to perform adjustments 3 a b
while tracking.)
b a
R B
G G
b B R
– 31 –
RM-954
4 BMC (Hexapole) Magnet. Blue Red

Neck assy Neck assy
If the red, green and blue dots are not balanced or aligned, then
use the BMC magnet to adjust in the manner described below.
R G B R G B R G B
Red Blue
VM board VM board
R B
G R G B G
R B
Note
1. The Red and Blue magnets should be equally far from the
horizontal center line.
5 Y separation axis correction magnet adjustment. 2. Do not separate the Red and Blue magnets too far. (Less than
1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN] 8 mm)
and [BRIGHTNESS] to [STANDARD] .
2. Adjust the Y separation axis correction magnet on the neck

assembly so that the horizontal lines at the top and bottom of
the screen are straight.
(2) Dynamic Convergence Adjustment

Preparation:
• Before starting this adjustment, adjust the horizontal static
convergence and the vertical static convergence
RB B
R
TLH TLV
RB
R
B
YCH XCV
– 32 –
RM-954
TLV Rotate TLV-2 VOL (29”, 34”) on DY 3-3. FOCUS ADJUSTMENT

Rotate TLV VOL (25”) on DY
Adjust FOCUS control on the flyback transformer for the best
XCV Rotate XCV Adj core on DY
focus.
YCH Rotate YCH VOL on DY
TLH Insert TLH Correction Plate to DY Pocket (Left or
Right)
ON DY:
YCH TLV1
XCV
Focus
TLV2
Screen
FLYBACK TRANSFORMER (T503)
(3) Screen-corner Convergence
b a
a-d : screen-corner
misconvergence
c d
Fix a Permalloy assy corresponding to the misconverged

areas. b
Permalloy assembly c
– 33 –
RM-954
3-4. G2 (SCREEN) AND WHITE BALANCE 2. WHITE BALANCE ADJUSTMENT

1) Set to Service Mode (Refer Section 4-1: ADJUSTMENTS
ADJUSTMENTS
1. G2 (SCREEN) ADJUSTMENT WITH COMMANDER).
1) Set the PICTURE to normal. 2) Input white raster signal.
2) Put to VIDEO input mode without signals. 3) Set the PICTURE to minimum.
3) Connect R, G and B of the C board cathode to the oscilloscope. 4) Select GCT (WHB 4) and BCT (WHB 5) with [1] and [4], and
4) Adjust BRIGHTNESS to obtain the cathode voltage to the value adjust the level with [3] and [6] for the best white balance.
below. 5) Set the PICTURE to maximum.
5) Adjust G2 (screen) on the FBT until picture shows the point 6) Select GDR (WHB 1) and BDR (WHB 2) with [1] and [4], and
before cut off. adjust the level with [3] and [6] for the best white balance.
7) Write into the memory by pressing [MUTING] then [0].
3. SUB BRIGHT ADJUSTMENT

Cathode setting voltage: 1) Set to service mode.
175 V ±2(VDC)...34",25",21"
2) Input a staircase signal of black to white from the pattern
180V ±2(VDC)...29"
generator.
0V
3) BRIGHTNESS .... 50%.
PICTURE ............ MINIMUM
4) Select SBR (WHB7) with [1] and [4], and adjust SBR (WHB7)
level with [3] and [6] so that the second stripe from the right is
dimly lit.
White
second from the right
Black
– 34 –
SECTION 4 RM-954
CIRCUIT ADJUSTMENTS
4-1. ADJUSTMENTS WITH COMMANDER

Service adjustments are made with the RM-954 that comes with
this unit. 1, 4 Select the adjustment item.
a. ENTERING SERVICE MODE ↓
3, 6 Raise/lower the data value.
With the unit on standby ↓
↓ [MUTING] Writes.
[DISPLAY] ↓
↓ - Executes the writing.
5
↓ 7, - All the data becomes the values in memory.
VOL (+) 8, - All user control goes to the standard state.
↓ 5, - Service data initialization (Be sure not to use
[POWER] usually.)
This operation sequence puts the unit into service mode. 2, - Write 50Hz adjustment data to 60Hz, or vice
versa.
b. METHOD OF CANCELLATION FROM SERVICE
MODE
Set the standby condition (Press [POWER] button on the commander),
then press [POWER] button again, hereupon it becomes TV mode.
c. METHOD OF WRITE INTO MEMORY

1) Set to Service Mode.
2) Press [1] (UP) and [4] (DOWN), select an item of adjustment. 1 2 3
3) Press [MUTING] button and it will indicate WRITE on the screen. 4 5 6
4) Press [0] button to write into memory. 7 8 9
-/-- 0
d. MEMORY WRITE CONFIRMATION METHOD
1) After adjustment, pull out the plug from AC outlet, and then SOUND
plug into AC outlet again. PIC MODE MENU
2) Turn the power switch ON and set to Service Mode. A/B ENTER
3) Call the adjusted items again to confirm adjustments were made.
The screen display is :

Device Name Item Name Marking of virgin NVM
Item No Data Mode
GEO 00 HPS 1C p SERVICE 50 PAL, SECAM : 50

NTSC : 60
601S 1.0C 59 7F 0 000A
Suffix No RM-954
(OEM Code)
Software version Total Power-On time (hours)
– 35 –
RM-954
4-2. ADJUSTMENT METHOD

Item Number 00 of device GEO
This explanation uses H-Position as an example. Use the same method for all Items. Use 1 and 4 to select the
1. Select “GEO 00 HPS” with the 1 and 4 buttons. adjustment item, use 3 and 6 to adjust, write with [MUTING],
2. Raise/lower the data with the 3 and 6 buttons. then execute the write with -.
3. Select the optimum state. (The standard is 1F for PAL reception.)
4. Write with the [MUTING] button. (The display changes to Note : 1. In [WRITE], the data for all items are written into memory
WRITE.) together.
5. Execute the writing with the - button. (The WRITE 2. For adjustment items that have different standard data
display will be changed to red color while excuting, and back between 50Hz or 60Hz, be sure to use the respective
to SERVICE.) input signal after adjustment.
GEO 00 HPS 1F SERVICE 50 GREEN

601S 1.0C 59 7F 0 000A
Adjusted with [3]
and [6] buttons.
GEO 00 HPS 1F WRITE 50 GREEN

601S 1.0C 59 7F 0 000A
Written with [MUTING]
GEO 00 HPS 1F SERVICE 50 RED

601S 1.0C 59 7F 0 000A The WRITE display
then the display
returns to a green
SERVICE.
Write executed with [0]
– 36 –
Adjustment Item Table
Device Functionality Note Data Range Function Note for Register Slava RAM Address
Name No Name Different Data No. (bit) Address (bit)
GEO 0 HPS 7 3F H Position 50/60HZ 12 (7-2) CXA2130S(88H) 96 (7-2)
1 HSZ 1F 3F H Size 50/60HZ 11 (7-2) 95 (7-2)
2 PAP 1F 3F Pin Amp 50/60HZ 13 (7-2) 97 (7-2)
3 TLT 7 0F Trapezium 50/60HZ 15 (7-4) 99 (7-4)
4 VPS 1F 3F V Position 50/60HZ 0F (7-2) 93 (7-2)
5 VSZ 1F 3F V Size 50/60HZ 0E (7-2) 92 (7-2)
6 SCO 7 0F S Correction 50/60HZ 10 (7-4) 94 (7-4)
7 VLN 7 0F V Linearity 50/60HZ 10 (3-0) 94 (3-0)
8 BOW 7 0F AFC Bow 50/60HZ 16 (7-4) 9A (7-4)
9 AGL 7 0F AFC-Angle 50/60HZ 16 (3-0) 9A (3-0)
0A UPN 1F 3F Upper Pin 50/60HZ 14 (7-2) 98 (7-2)
0B LPN 2F 3F Lower Pin 50/60HZ 18 (7-2) 9C (7-2)
0C HBL 1 1 H Blanking on/off 18 (1) 6C (1)
0D LBL 7 0F Left H Blanking 50/60HZ 17 (7-4) 9B (7-4)
0E RBL 7 0F Right H Blanking 50/60HZ 17 (3-0) 9B (3-0)
WHB 0 RDR 1F 3F R Drive DYNAMIC/other 09 (7-2) CXA2130S(88H) A3 (7-2)
1 GDR 1F 3F G Drive DYNAMIC/other 0A (7-2) A4 (7-2)
2 BDR 1F 3F B Drive DYNAMIC/other 0B (7-2) A5 (7-2)
– 37 –
3 RCT 7 0F R Cutoff SECAM/other 07 (3-0) A7 (3-0)

4 GCT 7 0F G Cutoff SECAM/other 08 (7-4) A8 (3-0)
5 BCT 7 0F B Cutoff SECAM/other 08 (3-0) A8 (3-0)
6 BMN 15 1F Brightness Minimum Data 06 (7-2) 106
7 SBR 1F 3F Sub Brightness Control 06 (7-2) 107
SAJ 0 PMX 33 3F Picture Maximum Data 03 (7-2) CXA2130S(88H) 105
1 SHU 8 0F Sub Hue Control TV/Video 05 (7-2) 108
2 SSH 8 0F Sub Sharpness Control TV/Video 07 (7-4) 109
3 SCL 1F 3F Sub Color Control NTSC/others 04 (7-2) 10A
VP 0 EHT 4 0F EHT Comp 50/60HZ 15 (3-0) CXA2130S(88H) 99 (3-0)
1 GMA 2 03 Gamma Correction NTSC/others 0B (1-0) 25B (1-0)
2 YDL 6 0F Y Delay PAL/SECAM/NTSC 0C (3-0) A0 (3-0)
3 SST 1 03 SECAM ID Start Position 1B (1-0) 6F (1-0)
4 SSP 1 03 SECAM ID Stop Position 1B (3-2) 6F (3-2)
5 SLV 2 03 SECAM ID Level 1C (1-0) 70 (1-0)
6 SBF 22 3F SECAM BELL fO 1C (7-2) 70 (7-2)
7 DYC 1 1 Dynamic Color on/off 0A (1) 5E (1)
8 ABL 1 1 ABL Mode Switching (except STANDARD mode) 09 (1) 5D (1)
9 VTH 1 1 ABL Detection Vth Switching 09 (0) 5D (0)
0A SFO 1 1 FO Switching for Sharpness NTSC/others 05 (1) 24A (1)
0B DCX 1 1 DC Trans. Ratio Switching 06 (1) 5A (1)
0C SHT 1 1 Pre-/Overshoot ratio Switch NTSC/others 06 (0) 24A (0)
RM-954
VP 0D HDW 0 1 H Drive Pulse Width Switch 00 (6) 54 (6)
0E AFC 1 03 AFC Gain Control TV/Video 0F (1-0) A1 (1-0)
0F HOS 7 0F H Oscillation 0C (7-4) 60 (7-4)
10 HSS 0 1 Slice Level of H Sync Sep. 0D (1) 61 (1)
11 VSS 0 1 Slice Level of V Sync Sep. 0D (0) 61 (0)
12 HMS 1 1 Macro Vision C/m off/on 50/60Hz 0E (0) 92 (0)
RM-954
13 YUV 0 1 YUV Switch Control 01 (0) 55 (0)
14 CDV 1 3 CD mode for Video Video only 0D (5-4) 259 (5-4)
15 RON 1 1 R ON not memorized 01 (3) 55 (3)
16 GON 1 1 G ON not memorized 01 (2) 55 (2)
17 BON 1 1 B ON not memorized 01 (1) 55 (1)
18 PON 1 1 P ON not memorized 00 (7) 54 (7)
19 BLK 0 1 BLK Off 12 (0) 66 (0)
1A VMC 0 1 VM Off 13 (0) 67 (0)
AP 0 BCS 1 3 Bass Center Shift #4 (3-0) TDA7315(80H) 24C (1-0)
1 TCS 1 3 Treble Center Shift #5 (3-0) 24D (1-0)
2 TRF 2 3 RF Treble Offset #5 (3-0) 24E (1-0)
– 38 –
MSP 0 WST 15 FF W/G Stereo Threshold MSP3415D(84H) 165

1 WBT EC FF W/G Bilingual Threshold 166
2 WLL 5 FF W/G Monaural Threshold 167
3 WAC 1 0F W/G Agreement Count 168
4 WDL 30 FF W/G Search Delay 169
5 NDL 20 FF NICAM Search Delay 16A
6 SDL 10 FF Stereo status Read Delay 16B
7 AGC 1 1 AGC Switch Auto/Constant 00BB (7) 116 (7)
8 REL 28 3F AGC Gain at Constant Mode 00BB (6-1) 116 (6-1)
9 CRM 0 1 Carrier muting on/off 00BB (9) 115 (9)
0A ACO 1 1 Audio Clock out on/off 0083 (5) 11A (5)
0B FP 1B 7F FM Prescale for non-M system 000E (14-8) 221
0C FPM 32 7F FM Prescale for M system 000E (14-8) 222
0D FH 36 7F FM Prescale for HDEV 000E (14-8) 223
0E FHM 65 7F FM Prescale for HDEV and M 000E (14-8) 224
0F WGP 2A 7F W/G Prescale 000E (14-8) 225
10 NIP 6D 7F NICAM Prescale 0010 (14-8) 14F
11 ERR 50 FF Auto FM switch Threshold 0021 (10-3) 174
12 VOL 6D FF Loud Speaker gain 07xx0 TEMPORARY 0000 (11-4) 254
SVP 0 SBF 22 3F SECAM BELL f0 1C (7-2) CXA2060AS(8AH) 85 (7-2)
1 HOS 7 0F H Oscillation 0C (7-4) 80 (7-4)
2 SHU 8 0F Sub Hue Control 05 (7-2) 210
3 SCL 1F 3F Sub Color Control 04 (7-2) 211
PIP 0 SDL 02 0F Delay of output SELECT 01 (6-3) SDA9288X(D6H) 1A0 (6-3)
1 PPH 15 FF H Position of TOP-LEFT Pin P 01/02 1AF
2 PPV 2E FF V Position of TOP-LEFT Pin P 03 (7-0) 1B0
3 YDL 0 07 Delay of Luminance Input 04 (2-0) 1A3 (2-0)
4 HDI 00 0F H Sync Delay for Inset 06 (3-0) 1A5 (3-0)
5 ISC 01 1 Inset Clock Selection 06 (4) 1A5 (4)
6 CLP 1 1 Clamp Pulse Selection 06 (5) 1A5 (5)
7 CLC 0 1 Clamp Cycle Selection 06 (6) 1A5 (6)
8 CON 00 0F Contrast Adjustment for inset 09 (7-4) 1A8 (7-4)
9 PLL 2 03 H Position For A-ch 0D (6-5) 1AC (6-5)
0A PDV 0 0F PIP V Pedestal Level 0E (7-4) 1AD (7-4)
0B PDU 0 0F PIP U Pedestal Level 0E (3-0) 1AD (3-0)
TXT 0 TXH 1 3 Teletext Horizontal Position 10 (1-0) SAA5261(58H) 248 (1-0)
– 39 –
1 TXV 0 3 Teletext Vertical Position 10 (6-4) 248 (5-4)

OPM 0 OSH 0A 3F OSD H Position Option-Misc 1F1 CXP86461(60H) 18D (7-2)
1 COM 1 03 Comb Selection 23F (7-6)
2 APC 1 1 APC Switch 23E (5)
3 TSY 0 03 TV Sys at Auto TV Sys 23E (4-3)
4 MUT 0 1 No Signal Mute 23E (0)
5 AFM 1 1 Auto FM switch 23E (1)
6 RFB 0 3 C-BPF Control 23F (5-4)
7 TVO 0 7 Tilt to V-Angle offset 23F (2-0)
OPB 0 OP1 FF FF Optional Bits 1 (see below) Option-Bits CXP86461(60H) 48
1 OP2 E3 FF Optional Bits 2 (see below) 49
2 OP3 0 FF Optional Bits 3 (see below) 4A
NOTE
• shaded items are fixed data.
• Standard data listed on the Adjustment Item Table are reference values, therefore it may be different for each model and for each mode.
• Note for Different Data Those are the standard data values written on the microprocessor. Therefore, the data values of the modes and stored respectively in the
memory.
In case of a device replacement, adjustment by rewriting the data value is necessary for some items.
RM-954
RM-954
ITEM INFORMATION.
No. OPB0 OP1
Item XTAL 4.43 XTAL 3.58 SECAM 2nd. Lang B/G I D/K M
KV-XF29M35 1 1 1 1 1 1 1 1
KV-XF29M63 1 1 1 0 1 1 1 1
KV-XF29M93 1 1 1 0 1 1 1 1
No. OPB1 OP2

Item TOP NICAM HDEV Thai Bil – DVD Input AV Input
KV-XF29M35 0 1 1 0 0 0 1 1
KV-XF29M63 0 1 0 0 0 0 1 1
KV-XF29M93 0 1 0 0 0 0 1 1
No. OPB2 OP3

Item – – Auto PIC Auto TV sys US ST Arabic 11 KEY Chinese
KV-XF29M35 0 0 1 1 0 1 0 1
KV-XF29M63 0 0 1 1 0 1 0 0
KV-XF29M93 0 0 1 1 0 1 0 0
– 40 –
RM-954
4-3. PICTURE QUALITY ADJUSTMENTS BELL FILTER ADJUSTMENT

SUB COLOR ADJUSTMENT 1. Input SECAM color-bar signal.
1. Input a PAL color-bar. 2. Connect the dual-trace oscilloscope to CN303 pin 9
2. Set to the following condition: (not mounted).
PICTURE 100%, BRIGHTNESS 50%, COLOR 50% 3. Adjust SERVICE MODE, ITEMS ‘SBF’ as shown below.
3. Connect an oscilloscope to pin 1 (B OUT) of CN305, A board.
4. Set to Service Mode and select SAJ 3 ‘SCL’ with 1 and 4 of
the commander then adjust to VB2=VB3=VB4 with 3 and
6.
5. Press [MUTING] → - of the commander to write the data.
6. Adjust SAJ 3 ‘SCL’ as step 2 to 5 when receiving NTSC color-
bar.
4-4. A BOARD ADJUSTMENT AFTER IC003
(MEMORY) REPLACEMENT
When replacing IC003 (MEMORY), be sure to change IC001 (µ-

COM) to the following new IC at the same time.
IC001(µ-CON):
VB1 VB2 VB3 VB4
CXP86461-608S (KV-XF29M35)
VB2 = VB3 = VB4
CXP86461-602S (KV-XF29M63/XF29M93)
1. Enter to Service Mode.

SUB HUE ADJUSTMENT
1. Select Video 1. 2. Press commander buttons 5 and - (Data Initialize), and 2
2. Input a NTSC color-bar, video into Video 1. and - (Data Copy) to initialize the data.
3. Set the following condition:
PICTURE 100%, BRIGHTNESS 50%, COLOR 50% 3. Call each item number and check if the respective screen shows
4. Connect an oscilloscope to pin 1 (B OUT) of CN305, A board. the normal picture.
5. Select SAJ 1 ‘SHU’ with 1 and 4 of the commander by set- In cases where items are not well adjusted, rectify the items
ting to Service Mode and adjust to VB1=VB2=VB3=VB4 with with fine adjustment.
3 and 6. Write the data per each item number ([MUTING] +-).
4. Select item numbers “OPB0” (OP1), “OPB1” (OP2) and

“OPB2” (OP3) and respectively set the bit per model with
command buttons 3 and 6.
5. Press commander buttons 8 and - (Test Normal) to return

VB1 VB2 VB3 VB4
VB1 = VB2 = VB3 = VB4

to the data that was set on the shipment from the factory.
(This will also cancel Service Mode.)
6. Press [MUTING] → - of the commander to write the data.
– 41 –
RM-954
4-5. PICTURE DISTORTION ADJUSTMENT (1) PICTURE DISTORTION ADJUSTMENT (2)

Item Number 00 – 0B H-TRAPEZOID (Rotate RV1801)
GEO 0 HPS (H POSITION)
GEO 1 HSZ (H SIZE)
GEO 2 PAP (PIN AMP)
GEO 3 TLT (TRAPEZIUM)
GEO 4 VPS (V POSITION)
GEO 5 VSZ (V SIZE)
GEO 6 SCO (VERTICAL S-Correction)
GEO 7 VLN (V LINEARITY)
GEO 8 BOW (AFC.BOW)
GEO 9 AGL (AFC.ANGLE)
GEO 0A UCP (UPPER CORNER PIN)

GEO 0B LCP (LOWER CORNER PIN)
– 42 –
KV-XF29M35/XF29M63/XF29M93 KV-XF29M35/XF29M63/XF29M93 KV-XF29M35/XF29M63/XF29M93
SECTION 5 RM-954 RM-954 RM-954
DIAGRAM
5-1. BLOCK DIAGRAM
MAIN. TUVIF with TRU Surround BBE AUDIO PROCESSOR

TV V in AV SW 39
L1 out DBFB (3D) AUDIO OUT H3
STEREO DECODER 47 IC3201 IC3206 IC3207 TDA7315D
TV L in IC1401 R1 out Q6202/Q6206/6207 IC6201 3D SP BOX ASSY
(MSP3415) 48 38
NJM2187L NJM2150D <slave:80H>
CXA1855S TA74811
<slave: 84H> TV R in
TU101
46
<slave: 90H> B2 COMB FILTER
BTF-WG441 (Glass Combs) DAC IC3205 SP ASSY
<slave: C0H> CXA1315P AUDIO OUT
DBFB IC3202 IC6200
CN2302 <slave:48H>
V1 out TA8200AH
CN304
COMB Y in COMB C in CRT SOCKET
9 7 22 R out RED OUT
R out
STV5112
V1 V in Mon out DY
6 IC701
1 Y29RSA-M2 CRT
V1 L in 23 G out GREEN OUT
G out
2 CV/Y out CV/Y in YC JUNGLE M68LNH010X
V1 R in 43 4
VIDEO IN 1 4 IC301
V1 Y in C1 out C in
CXA2130S 24 B out BLUE OUT
B out
3 45 2
CN1405 CN101 <slave:88H>
V1 C in
5 IK in NECK ASSY
JACK BLOCK V1 S1 in 21 N/S DRIVE
6 IC1800
J1402 C
PIN 9P V2 V in
VM1 VM DRIVE
7 H-DRIVE HDT H-OUT FBT
V2 L in H. DRIVE Q5902/5906
VIDEO IN 2 8 19 Q506 T501 Q511 T503
V2 R in NX-4009
10 2SC2688 2SC4927
H. PULSE
18
PIN-CONT PIN-OUT PMT HLT

E/W
11 IC502 Q505 T505 T504
NJM2903M IRF614
VD+ V-OUT
13
VD- IC503
14
TDA8172
V. PARA DQP V. DRIVE DQP H. DRIVE DF TRANS

32 31 30 37 39 40 15 28 29 30 31
V out
IC2805 Q2822/2823 Q2811 T2801
U out
Y out
VM out
V in
U in
Y in
R G B BLK
H TIMING SHAPE DF DRIVE

V out 2
29
A R
D1 Q2821/IC2801 Q2805/2806/2807
TEXT DECODER G
MONITOR L out 2
Additional HALF
OUT R out 2
28
Color Matrix
with Ucom
IC801
B H3 5V REG & RESET STB TRANS STB SW TR DGC
26 BLK IC002 MM1319AF T604 Q605 AC CORD
SAA5261 RECEIVER
SBX1981-11 +B 2SK2845 THP
<slave: 58H> SYSTEM SIRCS SRT
IC3901 Audio Front Vcc POWER LINE
Ucom T603 THP600
+audio 3D Vcc FILTER
B3 V1 (KV-XF29M35 only) IC001
MEMORY -audio 3D Vcc
IC601
STR-F6656 T4601
CXP86461 11V
LINE FILTER
I2L IC003 +9V 9V REC IC603 T4602
ST24C08FB6 7V T601
+5V 5V REC IC604 F
– 43 – – 44 – – 45 –
RM-954 SECTION 6
EXPLODED VIEWS
NOTE:
• Items with no part number and no • Items marked " ∗ " are not stocked since
description are not stocked because they are seldom required for routine The components identified by
they are seldom required for routine service. Some delay should be shading and mark ! are critical
service. anticipated when ordering these items. for safety.
• The construction parts of an assembled Replace only with part number
part are indicated with a collation specified.
number in the remark column.
6-1. SPEAKER BRACKET

p: 7-685-663-71 SCREW +BVTP 4 × 16
r: 7-685-648-79 SCREW +BVTP 3 × 12
3
2
1 5
6
3
2
REF. NO. PART NO. DESCRIPTION REMARK
1 4-065-512-02 BRACKET, SPEAKER

2 4-374-745-21 CUSHION (A)
3 4-302-404-03 SCREW (WASHER HEAD) (+P 4X16)
4 1-529-190-11 SPEAKER (5CM)
5 ! 4-065-506-01 COVER, REAR
6 1-529-179-11 SPEAKER (8CM)
– 80 –
RM-954
6-2. CHASSIS
r: 7-685-648-71 SCREW BVTP 3 × 12
54
63
55
53
64 65
66
56
57 58
59
52
60
62
51
61
REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK
51 * A-1372-573-A
H3 BOARD, COMPLETE (KV-XF29M35) 59 * A-1298-718-A A BOARD, COMPLETE (KV-XF29M35)
* A-1372-606-A
H3 BOARD, COMPLETE (KV-XF29M63/XF29M93) * A-1298-802-A A BOARD, COMPLETE (KV-XF29M63/XF29M93)
52 * A-1135-972-A
B3 BOARD, COMPLETE (KV-XF29M35) 60 ! 1-453-284-11 TRANSFORMER ASSY, FLYBACK (NX4009//M3I4)
* A-1135-997-A
B3 BOARD, COMPLETE (KV-XF29M63/XF29M93)
(KV-XF29M63/XF29M93) ! 1-453-297-21 TRANSFORMER ASSY, FLYBACK (NX4009//M3I4)
53 * A-1388-228-A J2 BOARD, COMPLETE (KV-XF29M35) (KV-XF29M35)
* A-1388-243-A J2 BOARD, COMPLETE (KV-XF29M63/XF29M93) 61 * 4-066-681-03 BRACKET, MAIN
54 ! 4-022-115-00 HOLDER, AC CORD (KV-XF29M35) 62 * A-1343-640-A D1 BOARD, COMPLETE (KV-XF29M63/XF29M93)
! 4-022-115-21 HOLDER, AC CORD (KV-XF29M63/XF29M93) * A-1343-586-A D1 BOARD, COMPLETE (KV-XF29M35)
55 ! 1-574-358-11 CORD, POWER (WITH CONNECTOR) 7.5A/250V 63 * A-1241-361-A F BOARD, COMPLETE (KV-XF29M63/XF29M93)
(KV-XF29M35) * A-1241-346-A F BOARD, COMPLETE (KV-XF29M35)
! 1-574-062-61 CORD, POWER (WITH CONNECTOR) 2.5A/250V 64 * 4-066-682-01 BRACKET, F PWB
(KV-XF29M63/XF29M93) 65 * 4-066-683-03 HOLDER, PWB (KV-XF29M35 only)
56 4-066-684-11 BRACKET, TERMINAL 66 * A-1347-155-A V1 BOARD, COMPLETE (KV-XF29M35 only)

57 4-046-797-01 SCREW (3X12), (+)BVTAP
58 * A-1131-375-A B2 BOARD, COMPLETE (KV-XF29M35)
* A-1131-417-A B2 BOARD, COMPLETE (KV-XF29M63/XF29M93)
– 81 –
RM-954
6-3. PICTURE TUBE

NOTE : The picture tube for OCE model is upside-down, and the position for tension spring is changed accordingly.
r: 7-685-648-79 SCREW BVTP 3 × 12
120 121
114
126 119
122
127 118
113 116 117 121
128
115
108 123
109 130
124
115
125
112 113
111
104
105
110 107
102
106 129 103
101
101 X-4035-859-4 BEZNET ASSY (KV-XF29M35) 102-110, 129 116 2-163-920-01 PLATE, TLH CORRECTION
X-4036-445-1 BEZNET ASSY (KV-XF29M65) 102-110,129 117 8-451-494-21 DEFLECTION YOKE (Y29RSA-M2)
102 4-036-405-11 SPRING, COMPRESSION 118 8-453-011-11 NA299-M
103 4-065-508-01 BUTTON, POWER 119 * A-1331-906-A C BOARD, COMPLETE (KV-XF29M63/XF29M93)
104 4-047-464-01 CATCHER, PUSH * A-1331-872-A C BOARD, COMPLETE (KV-XF29M81)
105 4-045-250-21 DAMPER 120 ! 1-416-495-12 COIL, DEMAGNETIC
106 X-4036-231-1 DOOR, ASSY 121 * 4-062-970-11 CLIP (29RSN), DGC

107 X-4035-862-1 HANDLE ASSY (R) 122 4-061-369-01 HOLDER, DEGAUSE COIL
108 X-4035-861-1 HANDLE ASSY (L) 123 1-452-896-11 COIL, NA ROTATION (RT200)
109 4-065-509-01 BUTTON, CONTROL 124 * A-1342-469-A VM1 BOARD, COMPLETE
110 * 4-065-510-01 GUIDE, LIGHT (KV-XF29M63/XF29M93)
* A-1342-442-A VM1 BOARD, COMPLETE (KV-XF29M35)
111 4-372-556-11 SHEET, BLOTTING (KV-XF29M35) 125 4-369-318-61 SPRING, TENSION
4-054-468-01 SHEET, BLOTTING (KV-XF29M63/XF29M93)
112 ! 8-735-056-05 PICTURE TUBE (M68LNH010X) (KV-XF29M63) 126 1-452-032-00 MAGNET,DISC
! 8-735-057-05 PICTURE TUBE (M68LNH010X) 127 1-452-094-00 CIRCULAR DISC MAGNET B
(KV-XF29M35/XF29M93) 128 4-051-734-21 PIECE B(120), CONV. CORRECT (KV-XF29M35)
113 4-046-765-01 SCREW, TAPPING 7+CROWN WASHER 4-051-734-41 PIECE B(120), CONV. CORRECT
114 * 3-704-372-41 HOLDER, HV CABLE (KV-XF29M63/XF29M93) (KV-XF29M63/XF29M93)
* 3-704-372-11 HOLDER, HV CABLE (KV-XF29M35) 129 4-032-761-01 SHAFT(S), DOOR
115 4-046-600-11 SPACER, DY 130 4-068-028-01 BAND, DGC
– 82 –
RM-954
6-4. 3D SPEAKER
4: 7-685-661-71 SCREW BVTP 4 × 12
p: 7-685-663-71 SCREW BVTP 4 × 16
152
153
151
154
155
156
REF. NO. PART NO. DESCRIPTION REMARK
151 A-1501-377-B BOX ASSY, SPEAKER (3D)

152 * 4-065-515-01 BOX (TP), 3D SPEAKER
153 1-529-172-11 SPEAKER, LOUD (10CM)
154 * 4-065-516-01 BOX (BT), 3D SPEAKER
155 * 4-037-244-01 FOOT (KV-XF29M35 only)
156 4-302-428-03 SCREW (WASHER HEAD) (+P 3X12)
– 83 –
RM-954 SECTION 7 The components identified by shading
and mark ! are critical for safety.
ELECTRICAL PARTS LIST Replace only with part number specified.
A
NOTE:
• Items marked " ∗ " are not stocked since they • All resistors are in ohms
The components identified by shading are seldom required for routine service. • F : nonflammable
and mark ! are critical for safety. Some delay should be anticipated when or-
Replace only with part number specified. dering these items. CAPACITORS
• MF : µF, PF : µµF
• All variable and adjustable resistors have
When indicating parts by reference characteristic curve B, unless otherwise COILS
number, please include the board name. noted. • MMH : mH, UH : µH
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
* A-1298-718-A A BOARD, COMPLETE (KV-XF29M35) C303 1-125-805-91 ELECT 4.7MF 20% 50V
********************* (KV-XF29M63/XF29M93)
* A-1298-802-A A BOARD, COMPLETE (KV-XF29M63/XF29M93) C304 1-126-967-11 ELECT 47MF 20% 50V
*********************
C305 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
4-382-854-11 SCREW (M3X10), P, SW (+) C306 1-163-233-11 CERAMIC CHIP 18PF 5% 50V
4-382-854-21 SCREW (M3X14), P, SW (+) C307 1-163-233-11 CERAMIC CHIP 18PF 5% 50V
C308 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C309 1-126-957-11 ELECT 0.22MF 20% 50V
<CAPACITOR>
C311 1-126-964-11 ELECT 10MF 20% 50V
C004 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C312 1-164-346-11 CERAMIC CHIP 1MF 16V
C005 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C313 1-164-346-11 CERAMIC CHIP 1MF 16V
C006 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V C315 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C007 1-126-933-11 ELECT 100MF 20% 16V C316 1-126-967-11 ELECT 47MF 20% 50V
C014 1-126-967-11 ELECT 47MF 20% 50V (KV-XF29M35)
C015 1-163-009-11 CERAMIC CHIP 0.001MF 10% 50V C317 1-163-031-11 CERAMIC CHIP 0.01MF 50V
C016 1-163-243-11 CERAMIC CHIP 47PF 5% 50V (KV-XF29M63/XF29M93)
C017 1-163-113-00 CERAMIC CHIP 68PF 5% 50V C318 1-163-031-11 CERAMIC CHIP 0.01MF 50V
C019 1-104-665-11 ELECT 100MF 20% 25V C319 1-163-031-11 CERAMIC CHIP 0.01MF 50V
C320 1-163-031-11 CERAMIC CHIP 0.01MF 50V
C022 1-163-227-11 CERAMIC CHIP 10PF 0.5PF 50V
C023 1-163-227-11 CERAMIC CHIP 10PF 0.5PF 50V C322 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C024 1-163-227-11 CERAMIC CHIP 10PF 0.5PF 50V C323 1-126-965-11 ELECT 22MF 20% 50V
C027 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V C325 1-126-960-11 ELECT 1MF 20% 50V
C327 1-126-965-11 ELECT 22MF 20% 50V
C030 1-126-965-11 ELECT 22MF 20% 50V C328 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C034 1-163-031-11 CERAMIC CHIP 0.01MF 50V C331 1-126-963-11 ELECT 4.7MF 20% 50V
(KV-XF29M35)
C041 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C331 1-125-797-91 ELECT 10MF 20% 50V
C042 1-163-251-11 CERAMIC CHIP 100PF 5% 50V (KV-XF29M63/XF29M93)
C047 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C332 1-126-963-11 ELECT 4.7MF 20% 50V
C104 1-126-933-11 ELECT 100MF 20% 16V C337 1-126-961-11 ELECT 2.2MF 20% 50V
C107 1-163-005-11 CERAMIC CHIP 470PF 10% 50V C338 1-163-017-00 CERAMIC CHIP 0.0047MF 10% 50V
C108 1-126-933-11 ELECT 100MF 20% 16V
C110 1-163-005-11 CERAMIC CHIP 470PF 10% 50V C342 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C113 1-126-967-11 ELECT 47MF 20% 50V
C114 1-126-967-11 ELECT 47MF 20% 50V C507 1-161-830-00 CERAMIC 0.0047MF 500V
C300 1-164-505-11 CERAMIC CHIP 2.2MF 16V C510 1-102-112-00 CERAMIC 330PF 10% 50V
C301 1-126-935-11 ELECT 470MF 20% 16V C514 1-106-383-00 MYLAR 0.047MF 10% 200V
C303 1-126-959-11 ELECT 0.47MF 20% 50V
(KV-XF29M35)
– 84 –
RM-954
The components identified by shading
Replace only with part number specified.
A
C519 1-102-212-00 CERAMIC 820PF 10% 500V C610 1-126-964-11 ELECT 10MF 20% 50V
C521 1-104-666-11 ELECT 220MF 20% 25V C611 1-161-830-00 CERAMIC 0.0047MF 99% 500V
C522 1-126-933-11 ELECT 100MF 20% 16V C612 1-161-830-00 CERAMIC 0.0047MF 99% 500V
C526 1-130-495-00 MYLAR 0.1MF 5% 50V C615 ! 1-119-886-51 CERAMIC 470PF 10% 250V
C527 1-102-820-00 CERAMIC 330PF 5% 50V C616 1-130-202-00 FILM 0.022MF 5% 400V
C528 1-162-116-00 CERAMIC 680PF 10% 2KV C617 1-107-792-11 CERAMIC 100PF 5% 1KV
C530 1-137-372-11 FILM 0.022MF 5% 50V C618 1-125-893-11 FILM 680PF 3% 1.5KV
C531 1-107-903-11 ELECT 2.2MF 20% 50V C619 ! 1-119-886-51 CERAMIC 470PF 10% 250V
C532 1-128-528-11 ELECT 470MF 20% 25V C620 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C533 1-128-528-11 ELECT 470MF 20% 25V C621 1-102-114-00 CERAMIC 470PF 10% 50V
C536 1-136-165-00 FILM 0.1MF 5% 50V C622 1-102-119-00 CERAMIC 0.0015MF 10% 50V
C538 1-136-617-11 FILM 0.019MF 3% 2KV C624 1-125-772-91 CERAMIC 1500PF 10% 2KV
C539 1-129-723-00 FILM 0.056MF 5% 630V C625 1-102-002-00 CERAMIC 680PF 10% 500V
C540 1-136-171-00 FILM 0.33MF 5% 50V C626 1-102-002-00 CERAMIC 680PF 10% 500V
C546 1-165-319-11 CERAMIC CHIP 0.1MF 50V C627 1-102-002-00 CERAMIC 680PF 10% 500V
C550 1-106-220-00 MYLAR 0.1MF 10% 100V C629 1-126-964-11 ELECT 10MF 20% 50V
C551 1-126-960-11 ELECT 1MF 20% 50V C630 1-125-494-11 ELECT(BLOCK) 560MF 20% 160V
(KV-XF29M35) C631 1-128-550-11 ELECT 2200MF 20% 50V
(KV-XF29M63/XF29M93) C633 1-104-999-11 MYLAR 0.1MF 10% 200V
C552 1-162-116-00 CERAMIC 680PF 10% 2KV
C553 1-162-116-00 CERAMIC 680PF 10% 2KV C634 1-126-934-11 ELECT 220MF 20% 16V
C635 1-104-665-11 ELECT 100MF 20% 10V
C554 1-137-417-11 MYLAR 0.0047MF 10% 200V C636 1-104-760-11 CERAMIC CHIP 0.047MF 10% 50V
C556 1-128-528-11 ELECT 470MF 20% 25V C638 1-161-830-00 CERAMIC 0.0047MF 500V
C557 1-126-941-11 ELECT 470MF 20% 25V C641 1-102-002-00 CERAMIC 680PF 10% 500V
C558 1-123-024-21 ELECT 33MF 160V
C643 1-126-933-11 ELECT 100MF 20% 16V
C561 1-136-557-11 FILM 0.0033MF 5% 630V C644 1-104-331-11 CERAMIC 0.0022MF 10% 1KV
C562 1-102-228-00 CERAMIC 470PF 10% 500V C645 1-137-605-11 FILM 0.01MF 10% 250V
C649 1-126-940-11 ELECT 330MF 20% 25V
C566 1-102-244-00 CERAMIC 220PF 10% 500V C650 1-163-275-11 CERAMIC CHIP 0.001MF 5% 50V
C567 1-115-520-11 FILM 0.68MF 5% 250V C651 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C570 1-115-522-11 FILM 1MF 5% 250V
C571 1-126-959-11 ELECT 0.47MF 20% 50V C653 1-126-967-11 ELECT 47MF 20% 50V
C655 ! 1-119-886-51 CERAMIC 470PF 10% 250V
C572 1-117-661-71 FILM 0.15MF 5% 250V C657 1-101-821-00 CERAMIC 0.0022MF 500V
C573 1-106-387-00 MYLAR 0.068MF 10% 200V C912 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C576 1-130-495-00 MYLAR 0.1MF 5% 50V
C577 1-106-395-00 MYLAR 0.15MF 10% 200V
<CONNECTOR>
C579 1-102-038-00 CERAMIC 0.001MF 500V
C582 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V CN101 * 1-779-890-11 CONNECTOR, BOARD TO BOARD 10P
C600 ! 1-104-705-51 FILM 0.1MF 20% 250V CN102 * 1-779-889-11 CONNECTOR, BOARD TO BOARD 8P
C601 1-136-601-11 FILM 0.01MF 5% 630V CN104 1-695-915-11 TAB (CONTACT)
C603 1-126-967-11 ELECT 47MF 20% 50V CN105 * 1-508-784-21 PIN, CONNECTOR (5MM PITCH) 1P
CN106 * 1-564-506-11 PLUG, CONNECTOR 3P
C605 ! 1-119-886-51 CERAMIC 470PF 10% 250V CN201 * 1-564-510-11 PLUG, CONNECTOR 7P
C606 ! 1-119-886-51 CERAMIC 470PF 10% 250V CN202 * 1-508-847-00 PIN, CONNECTOR 4P
C607 1-161-830-00 CERAMIC 0.0047MF 99% 500V CN301 * 1-774-813-11 CONNECTOR, BOARD TO BOARD 7P
C608 1-161-830-00 CERAMIC 0.0047MF 99% 500V (KV-XF29M35 ONLY)
CN304 * 1-766-955-11 CONNECTOR, BOARD TO BOARD 11P
– 85 –
RM-954
A
CN307 * 1-774-813-11 CONNECTOR, BOARD TO BOARD 7P D523 8-719-302-43 DIODE EL1Z

(KV-XF29M35 ONLY) D525 8-719-911-19 DIODE 1SS119-25
CN501 * 1-508-784-21 PIN, CONNECTOR (5MM PITCH) 1P D526 8-719-150-92 DIODE RD33EB3T
CN502 * 1-508-784-21 PIN, CONNECTOR (5MM PITCH) 1P D527 8-719-908-03 DIODE GP08D
CN503 * 1-564-510-11 PLUG, CONNECTOR 7P D528 8-719-908-03 DIODE GP08D
CN504 1-695-915-11 TAB (CONTACT)
D529 8-719-028-72 DIODE RGP02-17EL-6433
CN505 * 1-508-766-00 PIN, CONNECTOR (5MM PITCH) 4P D531 8-719-988-61 DIODE 1SS355TE-17
CN507 * 1-564-509-11 PLUG, CONNECTOR 6P D532 8-719-988-61 DIODE 1SS355TE-17
CN508 1-695-915-11 TAB (CONTACT) D600 8-719-911-19 DIODE 1SS119-25
CN509 1-695-915-11 TAB (CONTACT) D602 8-719-911-19 DIODE 1SS119-25
D603 8-719-150-92 DIODE RD33EB3T
CN601 * 1-580-843-11 PIN, CONNECTOR (POWER) D604 8-719-028-72 DIODE RGP02-17EL-6433
CN602 * 1-508-786-00 PIN, CONNECTOR (5MM PITCH) 2P D605 8-719-510-53 DIODE D4SB60L
CN603 * 1-508-784-21 PIN, CONNECTOR (5MM PITCH) 1P D606 8-719-108-18 THYRISTOR 5P6M
CN604 * 1-573-963-11 PIN, CONNECTOR (PC BOARD) 3P D607 8-719-404-50 DIODE MA111-TX
D608 8-719-110-53 DIODE RD20ESB2
CN608 * 1-564-507-11 PLUG, CONNECTOR 4P D609 8-719-311-31 DIODE RU-1P
CN904 * 1-564-512-11 PLUG, CONNECTOR 9P D610 8-719-043-76 DIODE AK04V0
D611 8-719-046-74 DIODE AU-01Z-V1
D612 8-719-043-52 DIODE F5KQ60
<DIODE>
D613 8-719-046-74 DIODE AU-01Z-V1
D001 8-719-988-61 DIODE 1SS355TE-17 D614 8-719-046-74 DIODE AU-01Z-V1
D002 8-719-988-61 DIODE 1SS355TE-17 D620 8-719-110-72 DIODE RD30ESB2
D005 8-719-988-61 DIODE 1SS355TE-17 D621 8-719-071-38 DIODE D5S6M
D006 1-216-295-91 SHORT 0 D622 8-719-071-39 DIODE FMU-G26S
D100 8-719-404-50 DIODE MA111-TX (KV-XF29M35 ONLY)
D623 8-719-978-65 DIODE DTZ-TT11-15B
D300 1-216-295-91 SHORT 0 D624 8-719-404-50 DIODE MA111-TX
D301 8-719-988-61 DIODE 1SS355TE-17 D625 8-719-158-39 DIODE RD10SB
D303 8-719-988-61 DIODE 1SS355TE-17 D628 8-719-911-19 DIODE 1SS119-25
D304 8-719-988-61 DIODE 1SS355TE-17 D629 8-719-510-37 DIODE D5LC20U (KV-XF29M35)
D305 8-719-988-61 DIODE 1SS355TE-17
D629 8-719-052-74 DIODE FMX-12S (KV-XF29M63/XF29M93)
D306 8-719-988-61 DIODE 1SS355TE-17 D630 8-719-510-37 DIODE D5LC20U
D307 8-719-988-61 DIODE 1SS355TE-17 D631 8-719-068-00 DIODE ERC04-06SE
D308 8-719-988-61 DIODE 1SS355TE-17 D632 8-719-068-00 DIODE ERC04-06SE
D309 8-719-159-10 DIODE RD5.1SB-T2 D633 8-719-948-45 DIODE ERA22-08
D311 8-719-988-61 DIODE 1SS355TE-17
D634 ! 8-719-404-50 DIODE MA111-TX
D312 8-719-988-61 DIODE 1SS355TE-17 D635 8-719-404-50 DIODE MA111-TX
D313 8-719-988-61 DIODE 1SS355TE-17 D636 8-719-510-02 DIODE D1NS4
D315 8-719-988-61 DIODE 1SS355TE-17 D637 8-719-109-96 DIODE RD6.8ESB1
D316 8-719-069-57 DIODE UDZS-TE17-6.8B (KV-XF29M35) D638 8-719-510-48 DIODE D1N20R
D316 8-719-109-96 DIODE RD6.8ESB1 (KV-XF29M63/XF29M93)
D504 8-719-302-43 DIODE EL1Z <CONNECTOR>

D505 8-719-988-61 DIODE 1SS355TE-17
D506 8-719-911-19 DIODE 1SS119-25 DY1 * 1-580-798-11 CONNECTOR PIN (DY) 6P
D507 8-719-988-61 DIODE 1SS355TE-17
D508 8-719-988-61 DIODE 1SS355TE-17
<FERRITE BEAD>
D509 1-216-063-91 RES,CHIP 3.9K 5% 1/10W
D510 8-719-988-61 DIODE 1SS355TE-17 FB501 1-410-397-21 FERRITE 1.1UH
D513 8-719-908-03 DIODE GP08D FB601 1-410-397-21 FERRITE 1.1UH
FB602 1-410-397-21 FERRITE 1.1UH
D517 8-719-945-80 DIODE ERC06-15S
D518 8-719-900-26 DIODE ERD29-08J FB603 1-410-397-21 FERRITE 1.1UH
D519 8-719-945-80 DIODE ERC06-15S FB604 1-410-397-21 FERRITE 1.1UH
D521 8-719-302-43 DIODE EL1Z FB605 1-412-911-31 FERRITE 0UH
D522 8-719-979-85 DIODE EGP20G FB606 1-412-911-31 FERRITE 0UH
FB607 1-410-397-21 FERRITE 1.1UH
– 86 –
RM-954
A
FB608 1-412-911-31 FERRITE 0UH L506 1-412-525-31 INDUCTOR 10UH

FB611 1-410-397-21 FERRITE 1.1UH L507 1-459-111-00 INDUCTOR 10MMH
FB612 1-410-397-21 FERRITE 1.1UH L508 1-412-525-31 INDUCTOR 10UH
FB613 1-410-397-21 FERRITE 1.1UH L511 1-406-977-21 INDUCTOR 100UH
FB615 1-410-397-21 FERRITE 1.1UH L512 1-412-549-31 INDUCTOR 1MMH
L513 1-412-549-31 INDUCTOR 1MMH

<IC> L515 1-459-104-00 COIL, WITH CORE
L518 1-408-611-31 INDUCTOR 47UH
IC001 8-752-903-51 IC CXP86461-608S (KV-XF29M35) L601 1-412-527-11 INDUCTOR 15UH
IC001 8-752-897-84 IC CXP86461-602S (KV-XF29M63/XF29M93) L905 1-414-856-11 INDUCTOR 10UH
IC002 8-759-371-21 IC MM1319AFBE
IC003 8-759-370-34 IC ST24C08FB6
IC100 8-759-042-02 IC S-80743AL-A7-S (KV-XF29M35 ONLY) <PHOTO COUPLER>
IC301 8-752-088-39 IC CXA2130S PH600 ! 8-749-924-35 PHOTO COUPLER ON3171-R

IC502 8-759-700-07 IC NJM2903M
IC503 8-759-980-58 IC TDA8172
IC601 8-749-014-48 IC STR-F6656 <TRANSISTOR>
IC602 8-749-920-61 IC SE-135N
Q001 8-729-216-22 TRANSISTOR 2SA1162-G
IC603 8-759-701-59 IC NJM78M09FA Q002 8-729-230-49 TRANSISTOR 2SC2712-YG
IC604 8-759-231-53 IC TA7805S Q003 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q004 8-729-027-43 TRANSISTOR DTC114EKA-T146
Q005 8-729-030-02 TRANSISTOR DTC144ESA
<CHIP CONDUCTOR> (KV-XF29M63/XF29M93 ONLY)
JR002 1-216-295-91 SHORT 0 Q101 8-729-230-49 TRANSISTOR 2SC2712-YG

JR004 1-216-295-91 SHORT 0 Q301 8-729-216-22 TRANSISTOR 2SA1162-G

JR016 1-216-295-91 SHORT 0 Q315 1-801-806-11 TRANSISTOR DTC144EK-T146

JR303 1-216-295-91 SHORT 0 Q505 8-729-931-45 TRANSISTOR IRF614
JR500 1-216-295-91 SHORT 0 Q506 8-729-140-96 TRANSISTOR 2SD774-34

Q511 8-729-016-32 TRANSISTOR 2SC4927-01
Q600 8-729-119-78 TRANSISTOR 2SC2785-HFE
<COIL>
Q601 8-729-023-22 TRANSISTOR 2SD2114K
L002 1-414-856-11 INDUCTOR 10UH Q602 8-729-230-49 TRANSISTOR 2SC2712-YG
L003 1-414-180-11 INDUCTOR 3.3UH Q603 8-729-027-23 TRANSISTOR DTA114EKA-T146
L005 1-414-233-22 INDUCTOR CHIP 0UH Q604 8-729-200-17 TRANSISTOR 2SA1091-O
L101 1-414-856-11 INDUCTOR 10UH Q605 8-729-044-30 TRANSISTOR 2SK2845-LB102
L102 1-414-856-11 INDUCTOR 10UH
Q606 8-729-230-49 TRANSISTOR 2SC2712-YG
L103 1-414-856-11 INDUCTOR 10UH Q607 8-729-922-37 TRANSISTOR 2SD2144S-UVW
L104 1-414-856-11 INDUCTOR 10UH Q608 8-729-230-49 TRANSISTOR 2SC2712-YG
L105 1-414-856-11 INDUCTOR 10UH
L301 1-414-189-31 INDUCTOR 100UH
L302 1-414-185-41 INDUCTOR 22UH <RESISTOR>
L501 1-412-525-31 INDUCTOR 10UH R001 1-414-233-22 INDUCTOR CHIP 0UH

L502 1-422-613-11 COIL, AIR CORE R002 1-216-025-91 RES,CHIP 100 5% 1/10W
L503 1-412-525-31 INDUCTOR 10UH R003 1-216-073-00 RES,CHIP 10K 5% 1/10W
L504 1-412-525-31 INDUCTOR 10UH R004 1-216-025-91 RES,CHIP 100 5% 1/10W
L505 1-412-525-31 INDUCTOR 10UH R005 1-216-025-91 RES,CHIP 100 5% 1/10W
– 87 –
RM-954
A
R008 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R113 1-216-025-91 RES,CHIP 100 5% 1/10W
R013 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R301 1-216-113-00 RES,CHIP 470K 5% 1/10W
(KV-XF29M35)
R014 1-216-025-91 RES,CHIP 100 5% 1/10W
R015 1-216-025-91 RES,CHIP 100 5% 1/10W R301 1-216-089-91 RES,CHIP 47K 5% 1/10W
R016 1-216-025-91 RES,CHIP 100 5% 1/10W (KV-XF29M63/XF29M93)
R018 1-216-033-00 RES,CHIP 220 5% 1/10W R302 1-216-295-91 SHORT 0
R019 1-216-073-00 RES,CHIP 10K 5% 1/10W R303 1-216-049-91 RES,CHIP 1K 5% 1/10W
R304 1-216-073-00 RES,CHIP 10K 5% 1/10W
R022 1-216-025-91 RES,CHIP 100 5% 1/10W
R023 1-216-049-91 RES,CHIP 1K 5% 1/10W R308 1-216-025-91 RES,CHIP 100 5% 1/10W
R311 1-216-017-91 RES,CHIP 47 5% 1/10W
R027 1-216-049-91 RES,CHIP 1K 5% 1/10W
R028 1-216-073-00 RES,CHIP 10K 5% 1/10W R313 1-216-053-00 RES,CHIP 1.5K 5% 1/10W
(KV-XF29M35) R314 1-216-043-91 RES,CHIP 560 5% 1/10W
(KV-XF29M63/XF29M93) R317 1-216-077-00 RES,CHIP 15K 5% 1/10W

R032 1-216-025-91 RES,CHIP 100 5% 1/10W R320 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R035 1-216-025-91 RES,CHIP 100 5% 1/10W R322 1-216-033-00 RES,CHIP 220 5% 1/10W
R038 1-216-049-91 RES,CHIP 1K 5% 1/10W R331 1-216-295-91 SHORT 0
R042 1-216-295-91 SHORT 0 R334 1-216-129-00 RES,CHIP 2.2M 5% 1/10W
R045 1-414-233-22 INDUCTOR CHIP 0UH R339 1-216-033-00 RES,CHIP 220 5% 1/10W
R047 1-414-233-22 INDUCTOR CHIP 0UH R345 1-216-081-00 RES,CHIP 22K 5% 1/10W
R050 1-216-073-00 RES,CHIP 10K 5% 1/10W R348 1-216-675-11 METAL CHIP 10K 0.50% 1/10W

R061 1-216-295-91 SHORT 0 R356 1-216-057-00 RES,CHIP 2.2K 5% 1/10W

R105 1-216-295-91 SHORT 0 R364 1-216-295-91 SHORT 0
– 88 –
RM-954
A
R368 1-216-073-00 RES,CHIP 10K 5% 1/10W R556 1-215-437-00 METAL 4.7K 1% 1/4W
R370 1-216-033-00 RES,CHIP 220 5% 1/10W R557 1-216-363-00 METAL OXIDE 0.33 5% 2W F
R373 1-216-025-91 RES,CHIP 100 5% 1/10W R558 1-247-843-11 CARBON 3.3K 5% 1/4W
R375 1-216-025-91 RES,CHIP 100 5% 1/10W R559 1-249-429-11 CARBON 10K 5% 1/4W
(KV-XF29M35 ONLY) R560 1-216-073-00 RES,CHIP 10K 5% 1/10W
R376 1-216-081-00 RES,CHIP 22K 5% 1/10W
R561 1-216-049-91 RES,CHIP 1K 5% 1/10W
R377 1-216-121-91 RES,CHIP 1M 5% 1/10W R562 1-249-401-11 CARBON 47 5% 1/4W
R378 1-216-031-00 RES,CHIP 180 5% 1/10W R564 1-216-689-11 METAL CHIP 39K 0.50% 1/10W
R500 1-249-417-11 CARBON 1K 5% 1/4W R565 1-216-073-00 RES,CHIP 10K 5% 1/10W
(KV-XF29M35) R567 1-216-105-91 RES,CHIP 220K 5% 1/10W
R500 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93)
R501 1-216-049-91 RES,CHIP 1K 5% 1/10W R568 1-249-383-11 CARBON 1.5 5% 1/4W F
R570 1-216-069-00 RES,CHIP 6.8K 5% 1/10W
R505 1-216-699-11 METAL CHIP 100K 0.50% 1/10W R571 1-215-443-00 METAL 8.2K 1% 1/4W
R507 1-249-389-11 CARBON 4.7 5% 1/4W F R575 1-216-665-11 METAL CHIP 3.9K 0.50% 1/10W
R508 1-216-471-11 METAL OXIDE 27 5% 3W F
R509 1-216-473-11 METAL OXIDE 56 5% 3W F R577 1-215-913-11 METAL OXIDE 220 5% 3W F
R578 1-216-369-00 METAL OXIDE 1 5% 2W F
R510 1-216-449-11 METAL OXIDE 56 5% 2W F R579 1-216-295-91 SHORT 0
R511 1-215-908-00 METAL OXIDE 33 5% 3W F R580 1-216-699-11 METAL CHIP 100K 0.50% 1/10W
R512 1-249-432-11 CARBON 18K 5% 1/4W R581 1-216-659-11 METAL CHIP 2.2K 0.50% 1/10W
R513 1-215-485-00 METAL 470K 1% 1/4W
R514 1-215-487-00 METAL 560K 1% 1/4W R582 1-218-768-11 METAL CHIP 470K 0.50% 1/10W
R584 1-216-667-11 METAL CHIP 4.7K 0.50% 1/10W
R515 1-215-911-11 METAL OXIDE 100 5% 3W F R587 1-216-699-11 METAL CHIP 100K 0.50% 1/10W
R517 1-208-798-11 RES,CHIP 4.7K 0.50% 1/10W (KV-XF29M35)
R518 1-247-807-31 CARBON 100 5% 1/4W R587 1-216-295-91 SHORT 0 (KV-XF29M63/XF29M93)
R519 1-215-913-11 METAL OXIDE 220 5% 3W F R588 1-215-888-00 METAL OXIDE 220 5% 2W F
R520 1-215-445-00 METAL 10K 1% 1/4W
R589 1-215-888-00 METAL OXIDE 220 5% 2W F
R522 1-216-675-11 METAL CHIP 10K 0.50% 1/10W R590 1-215-465-00 METAL 68K 1% 1/4W
R523 1-249-411-11 CARBON 330 5% 1/4W R591 1-260-288-11 CARBON 0.47 5% 1/2W F
R525 1-218-776-11 METAL CHIP 1M 0.50% 1/10W R592 1-216-689-11 METAL CHIP 39K 0.50% 1/10W
R526 1-216-673-11 METAL CHIP 8.2K 0.50% 1/10W R593 1-260-288-11 CARBON 0.47 5% 1/2W F
R527 1-216-001-00 RES,CHIP 10 5% 1/10W
R594 1-260-288-11 CARBON 0.47 5% 1/2W F
R528 1-216-683-11 METAL CHIP 22K 0.50% 1/10W R596 1-215-918-00 METAL OXIDE 1.5K 5% 3W F
R529 1-216-635-11 METAL CHIP 220 0.50% 1/10W R597 1-247-750-11 CARBON 680 5% 1/2W F
R531 1-247-843-11 CARBON 3.3K 5% 1/4W R598 1-249-438-11 CARBON 56K 5% 1/4W
R533 1-249-417-11 CARBON 1K 5% 1/4W R599 1-249-389-11 CARBON 4.7 5% 1/4W
(KV-XF29M35)
R533 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93) R600 1-249-438-11 CARBON 56K 5% 1/4W
R601 1-249-420-11 CARBON 1.8K 5% 1/4W F
R534 1-216-361-00 METAL OXIDE 0.22 5% 2W F R602 1-249-389-11 CARBON 4.7 5% 1/4W F
R535 1-216-067-00 RES,CHIP 5.6K 5% 1/10W R603 1-215-485-00 METAL 470K 1% 1/4W
R537 1-216-673-11 METAL CHIP 8.2K 0.50% 1/10W
R539 1-216-049-91 RES,CHIP 1K 5% 1/10W R607 1-249-425-11 CARBON 4.7K 5% 1/4W
R608 1-240-205-91 CARBON 22M 5% 1/2W
R540 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R609 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
R543 1-216-437-00 METAL OXIDE 5.6K 5% 1W F
R544 1-215-918-00 METAL OXIDE 1.5K 5% 3W F R612 1-216-045-00 RES,CHIP 680 5% 1/10W
R614 1-216-041-00 RES,CHIP 470 5% 1/10W
R545 1-216-077-00 RES,CHIP 15K 5% 1/10W R615 1-216-369-00 METAL OXIDE 1 5% 2W F
R547 1-216-085-00 RES,CHIP 33K 5% 1/10W R617 1-247-791-91 CARBON 22 5% 1/4W
R548 1-216-665-11 METAL CHIP 3.9K 0.50% 1/10W
R549 1-215-452-00 METAL 20K 1% 1/4W R619 1-260-128-11 CARBON 270K 5% 1/2W
R621 1-215-859-00 METAL OXIDE 22 5% 1W F
R551 1-249-413-11 CARBON 470 5% 1/4W R624 1-216-089-91 RES,CHIP 47K 5% 1/10W
R553 1-215-453-00 METAL 22K 1% 1/4W
R554 1-215-453-00 METAL 22K 1% 1/4W
– 89 –
RM-954
A B2 B3
R627 1-240-251-11 CMT,MELF 6.8 5% 10W <THERMISTOR>

R629 1-247-747-11 CARBON 470 5% 1/2W F
R630 1-249-429-11 CARBON 10K 5% 1/4W F THP600 1-809-827-11 THERMISTOR, POSITIVE
R631 1-216-089-91 RES,CHIP 47K 5% 1/10W
R632 1-220-886-11 FUSIBLE 0.1 10% 1W F
<TUNER>
R634 ! 1-218-265-91 METAL 8.2M 5% 1W
R635 1-216-492-11 METAL OXIDE 82K 5% 3W F TU101 8-598-451-00 TUNER, FSS BTF-WG441
R636 1-215-924-00 METAL OXIDE 15K 5% 3W F
R637 1-216-492-11 METAL OXIDE 82K 5% 3W F
R639 1-216-361-21 METAL OXIDE 0.22 5% 2W F <CRYSTAL>
R640 1-249-415-11 CARBON 680 5% 1/4W X001 1-781-174-21 VIBRATOR, CERAMIC

R641 1-216-361-21 METAL OXIDE 0.22 5% 2W F X301 1-781-134-21 VIBRATOR, CRYSTAL
R642 1-249-419-11 CARBON 1.5K 5% 1/4W X302 1-781-132-21 VIBRATOR, CRYSTAL
R643 1-247-843-11 CARBON 3.3K 5% 1/4W
R644 1-249-419-11 CARBON 1.5K 5% 1/4W
R646 1-215-924-00 METAL OXIDE 15K 5% 3W F

R647 1-249-387-11 CARBON 3.3 5% 1/4W ***********************************************************************
R648 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
R649 1-249-417-11 CARBON 1K 5% 1/4W
(KV-XF29M35) * A-1131-375-A B2 BOARD, COMPLETE (KV-XF29M35)
R649 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93) *********************
R650 1-215-882-00 METAL OXIDE 22 5% 2W F * A-1131-417-A B2 BOARD, COMPLETE (KV-XF29M63/XF29M93)

R652 1-215-900-11 METAL OXIDE 22K 5% 2W F *********************
R653 1-215-873-00 METAL OXIDE 4.7K 5% 1W F
R654 1-216-369-00 METAL OXIDE 1 5% 2W F
R656 1-249-417-11 CARBON 1K 5% 1/4W
(KV-XF29M35) <CONNECTOR>
R656 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93) CN2302* 1-766-952-11 CONNECTOR, BOARD TO BOARD 11P
R657 1-260-127-11 CARBON 220K 5% 1/2W
R659 1-216-049-91 RES,CHIP 1K 5% 1/10W
R660 1-216-073-00 RES,CHIP 10K 5% 1/10W <MODULE>
R661 1-215-873-00 METAL OXIDE 4.7K 5% 1W F
YCM230 1-466-162-42 BLOCK, COM FILTER (CFB-4)
R909 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R910 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
<RELAY> ***********************************************************************
RY600 ! 1-755-040-11 RELAY

RY601 ! 1-755-266-11 RELAY, AC POWER * A-1135-972-A B3 BOARD, COMPLETE (KV-XF29M35)
*********************
* A-1135-997-A B3 BOARD, COMPLETE (KV-XF29M63/XF29M93)
<SWITCH> *********************
S501 1-572-707-11 SWITCH, LEVER

S502 1-572-707-11 SWITCH, LEVER 4-382-854-11 SCREW (M3X10), P, SW (+)
<TRANSFORMER> <CAPACITOR>
T501 1-437-195-11 TRANSFORMER, HORIZONTAL DRIVE C1402 1-104-664-11 ELECT 47MF 20% 25V
T503 ! 1-453-297-21 TRANSFORMER ASSY, FLYBACK (NX-4009//M3I4) C1404 1-216-295-91 SHORT 0
(KV-XF29M35) C1405 1-104-664-11 ELECT 47MF 20% 25V
T503 ! 1-453-284-11 TRANSFORMER ASSY, FLYBACK (NX-4009//M3I4) C1410 1-104-664-11 ELECT 47MF 20% 25V
(KV-XF29M63/XF29M93) C1411 1-216-295-91 SHORT 0
T504 1-431-693-11 TRANSFORMER, HORIZONTAL LINEAR
T505 1-426-981-11 TRANSFORMER, FERRITE (PMT) C1413 1-126-935-11 ELECT 470MF 20% 16V
C1414 1-164-346-11 CERAMIC CHIP 1MF 16V
T601 1-431-536-11 TRANSFORMER, LINE FILTER C1415 1-104-664-11 ELECT 47MF 20% 25V
T603 ! 1-431-946-11 TRANSFORMER, CONVERTER C1416 1-164-346-11 CERAMIC CHIP 1MF 16V
T604 ! 1-431-852-11 TRANSFORMER, CONVERTER (SRT) C1418 1-163-031-11 CERAMIC CHIP 0.01MF 50V
– 90 –
RM-954
B3
C1422 1-164-346-11 CERAMIC CHIP 1MF 16V C3259 1-125-798-91 ELECT 0.47MF 20% 63V
C1423 1-164-346-11 CERAMIC CHIP 1MF 16V (KV-XF29M63/XF29M93)
C1425 1-164-346-11 CERAMIC CHIP 1MF 16V C3260 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C1426 1-164-346-11 CERAMIC CHIP 1MF 16V C3262 1-126-933-11 ELECT 100MF 20% 16V
C3265 1-126-964-11 ELECT 10MF 20% 50V
C1429 1-126-966-11 ELECT 33MF 20% 50V
C1431 1-163-038-91 CERAMIC CHIP 0.1MF 25V C3266 1-126-964-11 ELECT 10MF 20% 50V
C1435 1-163-038-91 CERAMIC CHIP 0.1MF 25V C3270 1-164-690-91 CERAMIC CHIP 0.0022MF 5% 50V
(KV-XF29M35) C3280 1-115-419-11 CERAMIC CHIP 3300PF 5% 25V
(KV-XF29M63/XF29M93) C3282 1-126-964-11 ELECT 10MF 20% 50V
C3283 1-126-964-11 ELECT 10MF 20% 50V
C1461 1-164-346-11 CERAMIC CHIP 1MF 16V C3287 1-126-964-11 ELECT 10MF 20% 50V
C1462 1-164-346-11 CERAMIC CHIP 1MF 16V
C3207 1-164-489-11 CERAMIC CHIP 0.22MF 10% 16V C6200 1-216-295-91 SHORT 0
C6201 1-126-964-11 ELECT 10MF 20% 50V
C3212 1-126-964-11 ELECT 10MF 20% 50V C6205 1-130-495-00 MYLAR 0.1MF 5% 50V
C3213 1-104-665-11 ELECT 100MF 20% 25V
C6206 1-128-550-11 ELECT 2200MF 20% 50V
C3216 1-117-720-11 CERAMIC CHIP 4.7MF 10V C6209 1-130-495-00 MYLAR 0.1MF 5% 50V
C6211 1-104-661-91 ELECT 330MF 20% 16V
C3220 1-163-037-11 CERAMIC CHIP 0.022MF 10% 50V C6213 1-136-161-00 FILM 0.047MF 5% 50V
C3223 1-163-037-11 CERAMIC CHIP 0.022MF 10% 50V (KV-XF29M35)
C3224 1-164-505-11 CERAMIC CHIP 2.2MF 16V C6216 1-125-797-91 ELECT 10MF 20% 50V
C3225 1-163-038-91 CERAMIC CHIP 0.1MF 25V (KV-XF29M63/XF29M93)
(KV-XF29M35)
C3240 1-115-339-11 CERAMIC CHIP 0.1MF 10% 50V (KV-XF29M63/XF29M93)
C3249 1-216-295-91 SHORT 0
C3254 1-216-295-91 SHORT 0 C6220 1-164-505-11 CERAMIC CHIP 2.2MF 16V
(KV-XF29M35) (KV-XF29M35)
– 91 –
RM-954
B3
C6221 1-125-798-91 ELECT 0.47MF 20% 63V D1411 8-719-158-35 DIODE RD9.1SB
(KV-XF29M63/XF29M93) D1412 8-719-158-35 DIODE RD9.1SB
C6222 1-164-505-11 CERAMIC CHIP 2.2MF 16V D1415 8-719-158-35 DIODE RD9.1SB
C6223 1-126-960-11 ELECT 1MF 20% 50V D1416 8-719-158-35 DIODE RD9.1SB
(KV-XF29M35) D6200 8-719-109-86 DIODE RD5.1ESB3
C6223 1-125-799-91 ELECT 1MF 20% 63V D6205 8-719-988-61 DIODE 1SS355TE-17
(KV-XF29M63/XF29M93) D6211 8-719-404-50 DIODE MA111-TX
C6225 1-115-339-11 CERAMIC CHIP 0.1MF 10% 50V D6212 8-719-404-50 DIODE MA111-TX
C6227 1-128-550-11 ELECT 2200MF 20% 50V
C6228 1-115-339-11 CERAMIC CHIP 0.1MF 10% 50V <FERRITE BEAD>
C6229 1-164-505-11 CERAMIC CHIP 2.2MF 16V FB6201 1-410-397-21 FERRITE 1.1UH
C6230 1-115-339-11 CERAMIC CHIP 0.1MF 10% 50V FB6202 1-410-397-21 FERRITE 1.1UH
C6231 1-128-550-11 ELECT 2200MF 20% 50V
C6233 1-163-007-11 CERAMIC CHIP 680PF 10% 50V <IC>
C6234 1-163-017-00 CERAMIC CHIP 0.0047MF 10% 50V IC1401 8-752-068-46 IC CXA1855S
C6235 1-163-251-11 CERAMIC CHIP 100PF 5% 50V IC1404 8-759-701-59 IC NJM78M09FA
C6236 1-115-339-11 CERAMIC CHIP 0.1MF 10% 50V IC3200 8-759-100-96 IC UPC4558G2
C6237 1-136-177-00 FILM 1MF 5% 50V IC3201 8-759-553-44 IC NJM2187L
C6238 1-163-009-11 CERAMIC CHIP 0.001MF 10% 50V IC3202 8-759-100-96 IC UPC4558G2
C6239 1-127-682-51 ELECT MELF 2200MF 20% 25V IC3203 8-759-711-10 IC NJU4066BM
C6240 1-130-495-00 MYLAR 0.1MF 5% 50V IC3205 8-752-057-18 IC CXA1315P
C6241 1-136-161-00 FILM 0.047MF 5% 50V IC3206 8-759-496-02 IC NJM2150D
C6244 1-163-019-00 CERAMIC CHIP 0.0068MF 10% 50V IC3207 8-759-273-12 IC TDA7315D013TR
C6245 1-163-019-00 CERAMIC CHIP 0.0068MF 10% 50V IC6200 8-759-168-24 IC TA8200AH
C6249 1-216-295-91 SHORT 0 IC6201 8-759-553-45 IC TDA7481

C6251 1-126-965-11 ELECT 22MF 20% 50V
C6252 1-126-965-11 ELECT 22MF 20% 50V
C6253 1-126-959-11 ELECT 0.47MF 20% 50V <JACK>
(KV-XF29M35)
C6253 1-125-798-91 ELECT 0.47MF 20% 63V J1401 1-784-646-11 TERMINAL, S
(KV-XF29M63/XF29M93) J1402 1-778-388-11 JACK BLOCK, PIN 9P
<CONNECTOR> <CHIP CONDUCTOR>
CN1400* 1-564-512-11 PLUG, CONNECTOR 9P JR1405 1-216-295-91 SHORT 0

CN1401* 1-508-784-21 PIN, CONNECTOR (5MM PITCH) 1P JR1406 1-216-295-91 SHORT 0
CN1405* 1-779-892-11 CONNECTOR, BOARD TO BOARD 10P JR1408 1-216-295-91 SHORT 0
CN1407* 1-779-891-11 CONNECTOR, BOARD TO BOARD 8P JR3200 1-216-295-91 SHORT 0

JR3208 1-216-295-91 SHORT 0

<DIODE> JR3209 1-216-295-91 SHORT 0
JR6200 1-216-295-91 SHORT 0
D1401 8-719-158-35 DIODE RD9.1SB JR6201 1-216-295-91 SHORT 0
D1403 8-719-158-35 DIODE RD9.1SB
D1406 8-719-158-35 DIODE RD9.1SB

D1407 8-719-158-35 DIODE RD9.1SB <COIL>
D1408 8-719-158-35 DIODE RD9.1SB
D1409 8-719-158-35 DIODE RD9.1SB L1404 1-412-537-31 INDUCTOR 100UH
D1410 8-719-158-35 DIODE RD9.1SB L3202 1-414-856-11 INDUCTOR 10UH
L6202 1-416-857-11 INDUCTOR 65UH
– 92 –
RM-954
B3
<IC LINK> R1459 1-216-025-91 RES,CHIP 100 5% 1/10W

R1460 1-216-033-00 RES,CHIP 220 5% 1/10W
PS6200 1-532-686-21 LINK, IC 2.7A/150V R1463 1-216-073-00 RES,CHIP 10K 5% 1/10W
PS6201 1-532-686-21 LINK, IC 2.7A/150V R1464 1-216-113-00 RES,CHIP 470K 5% 1/10W
R1465 1-216-113-00 RES,CHIP 470K 5% 1/10W
<TRANSISTOR> R1466 1-216-033-00 RES,CHIP 220 5% 1/10W

R1467 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
Q1402 8-729-216-22 TRANSISTOR 2SA1162-G R1468 1-216-093-91 RES,CHIP 68K 5% 1/10W
Q1403 8-729-230-49 TRANSISTOR 2SC2712-YG R1469 1-216-105-91 RES,CHIP 220K 5% 1/10W
Q6201 1-801-806-11 TRANSISTOR DTC144EKA-T146 R1471 1-216-022-00 RES,CHIP 75 5% 1/10W
R1472 1-216-033-00 RES,CHIP 220 5% 1/10W
Q6202 8-729-230-49 TRANSISTOR 2SC2712-YG R1473 1-216-033-00 RES,CHIP 220 5% 1/10W
Q6204 1-801-806-11 TRANSISTOR DTC144EKA-T146 R1478 1-216-051-00 RES,CHIP 1.2K 5% 1/10W
R1480 1-216-105-91 RES,CHIP 220K 5% 1/10W
Q6207 8-729-224-62 TRANSISTOR 2SK246-GR R1481 1-216-022-00 RES,CHIP 75 5% 1/10W
R1485 1-216-025-91 RES,CHIP 100 5% 1/10W
<RESISTOR> R1486 1-216-067-00 RES,CHIP 5.6K 5% 1/10W

R1490 1-216-025-91 RES,CHIP 100 5% 1/10W
R1404 1-216-295-91 SHORT 0 R1492 1-216-021-00 RES,CHIP 68 5% 1/10W
R1407 1-216-033-00 RES,CHIP 220 5% 1/10W
R1497 1-216-041-00 RES,CHIP 470 5% 1/10W
R1412 1-216-295-91 SHORT 0 (KV-XF29M35)
R1414 1-216-025-91 RES,CHIP 100 5% 1/10W
R3209 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R1426 1-216-025-91 RES,CHIP 100 5% 1/10W (KV-XF29M63/XF29M93)
R1430 1-216-025-91 RES,CHIP 100 5% 1/10W (KV-XF29M35)
(KV-XF29M63/XF29M93)
R1435 1-216-022-00 RES,CHIP 75 5% 1/10W
R3216 1-216-073-00 RES,CHIP 10K 5% 1/10W
R1442 1-216-049-91 RES,CHIP 1K 5% 1/10W
R3225 1-216-073-00 RES,CHIP 10K 5% 1/10W
R1449 1-216-073-00 RES,CHIP 10K 5% 1/10W
R1450 1-216-073-00 RES,CHIP 10K 5% 1/10W R3227 1-216-129-00 RES,CHIP 2.2M 5% 1/10W
R1452 1-216-295-91 SHORT 0 R3229 1-216-095-00 RES,CHIP 82K 5% 1/10W
R3230 1-216-055-00 RES,CHIP 1.8K 5% 1/10W
R1455 1-216-073-00 RES,CHIP 10K 5% 1/10W
R3240 1-216-081-00 RES,CHIP 22K 5% 1/10W
R3241 1-216-093-91 RES,CHIP 68K 5% 1/10W
– 93 –
RM-954
B3
R3263 1-216-093-91 RES,CHIP 68K 5% 1/10W R6240 1-249-429-11 CARBON 10K 5% 1/4W
R3264 1-216-053-00 RES,CHIP 1.5K 5% 1/10W R6241 1-215-915-11 METAL OXIDE 470 5% 3W F
R3266 1-216-295-91 SHORT 0 R6242 1-215-915-11 METAL OXIDE 470 5% 3W F
(KV-XF29M35) R6250 1-216-295-91 SHORT 0
R3272 1-216-067-00 RES,CHIP 5.6K 5% 1/10W
(KV-XF29M63/XF29M93) R6251 1-216-049-91 RES,CHIP 1K 5% 1/10W
(KV-XF29M35)
R3274 1-216-069-00 RES,CHIP 6.8K 5% 1/10W (KV-XF29M63/XF29M93)
R3275 1-216-295-91 SHORT 0 R6252 1-216-097-91 RES,CHIP 100K 5% 1/10W
R3276 1-216-295-91 SHORT 0 R6253 1-216-041-00 RES,CHIP 470 5% 1/10W
R3277 1-216-073-00 RES,CHIP 10K 5% 1/10W (KV-XF29M35)
R6253 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R3278 1-216-067-00 RES,CHIP 5.6K 5% 1/10W (KV-XF29M63/XF29M93)
R3279 1-216-067-00 RES,CHIP 5.6K 5% 1/10W
R3281 1-216-033-00 RES,CHIP 220 5% 1/10W R6255 1-216-308-00 RES,CHIP 4.7 5% 1/10W
R6257 1-216-061-00 RES,CHIP 3.3K 5% 1/10W
R3284 1-216-073-00 RES,CHIP 10K 5% 1/10W
R3285 1-216-073-00 RES,CHIP 10K 5% 1/10W R6259 1-216-308-00 RES,CHIP 4.7 5% 1/10W
R6263 1-216-059-00 RES,CHIP 2.7K 5% 1/10W
R3289 1-216-073-00 RES,CHIP 10K 5% 1/10W
R3291 1-216-079-00 RES,CHIP 18K 5% 1/10W R6278 1-216-295-91 SHORT 0
R3294 1-216-073-00 RES,CHIP 10K 5% 1/10W
R3295 1-216-065-91 RES,CHIP 4.7K 5% 1/10W

R3296 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R3297 1-216-069-00 RES,CHIP 6.8K 5% 1/10W ***********************************************************************
R3298 1-216-069-00 RES,CHIP 6.8K 5% 1/10W
R3299 1-216-069-00 RES,CHIP 6.8K 5% 1/10W
(KV-XF29M35)
R3299 1-216-067-00 RES,CHIP 5.6K 5% 1/10W

R6200 1-216-089-91 RES,CHIP 47K 5% 1/10W
R6201 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R6202 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R6203 1-216-295-91 SHORT 0
– 94 –
RM-954
C
* A-1331-872-A C BOARD, COMPLETE (KV-XF29M35) D720 8-719-911-19 DIODE 1SS119-25

******************** D721 8-719-911-19 DIODE 1SS119-25
* A-1331-906-A C BOARD, COMPLETE (KV-XF29M63/XF29M93) D722 8-719-911-19 DIODE 1SS119-25
******************** D1803 8-719-911-19 DIODE 1SS119-25
D1804 8-719-911-19 DIODE 1SS119-25
4-382-854-11 SCREW (M3X10), P, SW (+) D1808 8-719-908-03 DIODE GP08D
<CAPACITOR> <IC>
C700 1-110-389-11 FILM MELF 0.1MF 5% 250V IC701 8-759-561-28 IC STV5112

C701 1-162-114-00 CERAMIC 0.0047MF 2KV IC1800 8-759-822-38 IC LA6510
C702 1-102-074-00 CERAMIC 0.001MF 10% 50V
C704 1-107-652-11 ELECT 10MF 20% 250V
C707 1-137-399-11 MYLAR 0.1MF 5% 50V <JACK>
C708 1-102-228-00 CERAMIC 470PF 10% 500V J701 ! 1-540-071-22 SOCKET, CRT
C709 1-102-228-00 CERAMIC 470PF 10% 500V
C710 1-102-960-00 CERAMIC 24PF 5% 50V
C711 1-102-852-91 CERAMIC 47PF 5% 50V <COIL>
C712 1-102-525-11 CERAMIC 68PF 5% 50V
L701 1-410-667-31 INDUCTOR 22UH
C713 1-102-228-00 CERAMIC 470PF 10% 500V L705 1-408-609-41 INDUCTOR 33UH
C716 1-126-968-11 ELECT 100MF 20% 50V L706 1-408-609-41 INDUCTOR 33UH
C717 1-107-651-11 ELECT 4.7MF 20% 250V L707 1-408-609-41 INDUCTOR 33UH
C726 1-104-664-11 ELECT 47MF 20% 25V
C1800 1-126-964-11 ELECT 10MF 20% 50V
<TRANSISTOR>
C1803 1-126-964-11 ELECT 10MF 20% 50V
C1804 1-126-964-11 ELECT 10MF 20% 50V Q1800 8-729-119-76 TRANSISTOR 2SA1175-HFE
C1809 1-126-942-61 ELECT 1000MF 20% 25V Q1802 8-729-119-78 TRANSISTOR 2SC2785-HFE
<CONNECTOR> <RESISTOR>
CN700 1-695-915-11 TAB (CONTACT) R700 1-249-393-11 CARBON 10 5% 1/4W F

CN701 1-508-765-00 PIN, CONNECTOR (5MM PITCH) 3P R701 1-249-496-11 CARBON 100K 5% 1/2W
CN702 1-695-915-11 TAB (CONTACT) R702 1-215-469-00 METAL 100K 1% 1/4W
CN703 * 1-564-509-11 PLUG, CONNECTOR 6P R703 1-215-414-00 METAL 510 1% 1/4W
CN704 1-695-915-11 TAB (CONTACT) R704 1-215-414-00 METAL 510 1% 1/4W
CN706 1-695-915-11 TAB (CONTACT) R705 1-249-417-11 CARBON 1K 5% 1/4W

CN1801* 1-564-509-11 PLUG, CONNECTOR 6P (KV-XF29M35)
CN1802* 1-564-506-11 PLUG, CONNECTOR 3P R705 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93)
R706 1-249-417-11 CARBON 1K 5% 1/4W
(KV-XF29M35)
<DIODE> R706 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93)
R707 1-215-414-00 METAL 510 1% 1/4W
D700 8-719-911-19 DIODE 1SS119-25
D701 8-719-911-19 DIODE 1SS119-25 R708 1-249-417-11 CARBON 1K 5% 1/4W
D702 8-719-911-19 DIODE 1SS119-25 (KV-XF29M35)
D703 8-719-911-19 DIODE 1SS119-25 R708 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93)
D704 8-719-911-19 DIODE 1SS119-25 R709 1-215-903-11 METAL OXIDE 68K 5% 2W F
R711 1-215-903-11 METAL OXIDE 68K 5% 2W F
D705 8-719-051-85 DIODE HSS83TD R712 1-215-903-11 METAL OXIDE 68K 5% 2W F
D706 8-719-051-85 DIODE HSS83TD
D707 8-719-051-85 DIODE HSS83TD R713 1-215-481-00 METAL 330K 1% 1/4W
D708 8-719-911-19 DIODE 1SS119-25 R714 1-249-425-11 CARBON 4.7K 5% 1/4W
D709 8-719-911-19 DIODE 1SS119-25 R715 1-249-413-11 CARBON 470 5% 1/4W
R716 1-249-413-11 CARBON 470 5% 1/4W
D710 8-719-911-19 DIODE 1SS119-25 R717 1-249-425-11 CARBON 4.7K 5% 1/4W
D711 8-719-110-23 DIODE RD11ESB3
D714 8-719-051-85 DIODE HSS83TD R718 1-247-752-11 CARBON 1K 5% 1/2W
D715 8-719-051-85 DIODE HSS83TD R719 1-249-425-11 CARBON 4.7K 5% 1/4W
D716 8-719-051-85 DIODE HSS83TD R722 1-247-752-11 CARBON 1K 5% 1/2W
R723 1-249-413-11 CARBON 470 5% 1/4W
R724 1-247-752-11 CARBON 1K 5% 1/2W
– 95 –
RM-954
C D1
R730 1-216-392-11 METAL OXIDE 1.8 5% 3W F C2829 1-164-161-11 CERAMIC CHIP 0.0022MF 10% 50V
R734 1-247-739-11 CARBON 100 5% 1/2W C2830 1-130-479-00 MYLAR 0.0047MF 5% 50V
R744 1-215-415-00 METAL 560 1% 1/4W
R745 1-215-410-00 METAL 360 1% 1/4W C2831 1-107-714-11 ELECT 10MF 20% 16V
R1800 1-249-417-11 CARBON 1K 5% 1/4W C2832 1-126-960-11 ELECT 1MF 20% 50V
(KV-XF29M35) C2833 1-137-366-11 FILM 0.0022MF 5% 50V
C2834 1-106-375-12 MYLAR 0.022MF 10% 250V
R1800 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93) C2835 1-216-295-91 SHORT 0
R1801 1-249-426-11 CARBON 5.6K 5% 1/4W
R1802 1-249-387-11 CARBON 3.3 5% 1/4W F C2837 1-102-129-00 CERAMIC 0.01MF 10% 50V
R1803 1-249-387-11 CARBON 3.3 5% 1/4W F C2840 1-106-383-00 MYLAR 0.047MF 5% 100V
R1805 1-249-429-11 CARBON 10K 5% 1/4W C2841 1-137-194-81 FILM 0.47MF 5% 50V
R1806 1-249-425-11 CARBON 4.7K 5% 1/4W

R1808 1-249-425-11 CARBON 4.7K 5% 1/4W <CONNECTOR>
R1809 1-249-435-11 CARBON 33K 5% 1/4W
R1810 1-249-435-11 CARBON 33K 5% 1/4W CN2821* 1-564-506-11 PLUG, CONNECTOR 3P
R1811 1-249-435-11 CARBON 33K 5% 1/4W CN2822* 1-564-510-11 PLUG, CONNECTOR 7P
R1812 1-249-435-11 CARBON 33K 5% 1/4W CN2823 1-695-915-11 TAB (CONTACT)
R1821 1-249-435-11 CARBON 33K 5% 1/4W

R1822 1-249-435-11 CARBON 33K 5% 1/4W <DIODE>
R1823 1-249-426-11 CARBON 5.6K 5% 1/4W
R1824 1-249-435-11 CARBON 33K 5% 1/4W D2801 8-719-988-61 DIODE 1SS355TE-17
R1825 1-247-843-11 CARBON 3.3K 5% 1/4W D2803 8-719-063-73 DIODE D1NL20U-TR
D2804 8-719-063-73 DIODE D1NL20U-TR
D2806 8-719-302-43 DIODE EL1Z
<VARIABLE RESISTOR> D2811 8-719-988-61 DIODE 1SS355TE-17
RV702 1-241-656-21 RES, ADJ, METAL FILM 110M D2813 8-719-988-61 DIODE 1SS355TE-17
RV1801 1-223-241-11 RES, ADJ, CARBON 47K
<IC>
IC2801 8-759-700-07 IC NJM2903M

*********************************************************************** IC2803 8-759-701-59 IC NJM78M09FA
IC2805 8-759-998-98 IC LM358D
* A-1343-586-A D1 BOARD, COMPLETE (KV-XF29M35)

********************* <CHIP CONDUCTOR>
* A-1343-640-A D1 BOARD, COMPLETE (KV-XF29M63/XF29M93)
********************* JR2803 1-216-295-91 SHORT 0
JR2804 1-216-295-91 SHORT 0
JR2815 1-216-295-91 SHORT 0
<CAPACITOR>
<COIL>
C2801 1-130-479-00 MYLAR 0.0047MF 5% 50V
C2803 1-136-357-11 FILM 680PF 5% 50V L2801 1-406-677-11 INDUCTOR 10MMH
C2805 1-104-664-11 ELECT 47MF 20% 25V L2802 1-406-989-21 INDUCTOR 10MMH
C2806 1-136-559-11 MYLAR 0.0047MF 10% 400V L2803 1-414-502-41 INDUCTOR 33MMH
C2809 1-126-964-11 ELECT 10MF 20% 50V L2806 1-406-678-11 INDUCTOR 15MMH
C2810 1-162-318-11 CERAMIC 0.001MF 10% 500V

C2811 1-107-938-11 ELECT 0.47MF 20% 160V <TRANSISTOR>
C2813 1-107-636-11 ELECT 10MF 20% 160V
C2814 1-126-964-11 ELECT 10MF 20% 50V Q2802 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R
C2817 1-102-244-00 CERAMIC 220PF 10% 500V Q2805 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R
Q2806 8-729-120-28 TRANSISTOR 2SC1623-L5L6
C2818 1-136-347-11 FILM 0.0047MF 5% 630V Q2807 8-729-043-95 TRANSISTOR 2SC3840(3)
C2819 1-104-664-11 ELECT 47MF 20% 25V Q2811 8-729-931-45 TRANSISTOR IRF614
C2820 1-107-714-11 ELECT 10MF 20% 16V
C2822 1-106-375-12 MYLAR 0.022MF 10% 250V Q2813 8-729-120-28 TRANSISTOR 2SC1623-L5L6
C2824 1-104-664-11 ELECT 47MF 20% 25V Q2821 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q2822 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R
C2825 1-136-759-11 FILM 0.039MF 5% 200V Q2823 8-729-017-06 TRANSISTOR 2SC4793
C2826 1-137-194-81 FILM 0.47MF 5% 50V
C2828 1-107-714-11 ELECT 10MF 20% 16V
– 96 –
RM-954
D1 F H3
<RESISTOR> * A-1241-346-A F BOARD, COMPLETE (KV-XF29M35)

********************
R2801 1-216-081-00 RES,CHIP 22K 5% 1/10W * A-1241-361-A F BOARD, COMPLETE (KV-XF29M63/XF29M93)
R2803 1-216-057-00 RES,CHIP 2.2K 5% 1/10W ********************
R2804 1-216-041-00 RES,CHIP 470 5% 1/10W
R2806 1-216-073-00 RES,CHIP 10K 5% 1/10W 1-533-223-11 HOLDER, FUSE
R2809 1-216-073-00 RES,CHIP 10K 5% 1/10W
R2812 1-216-097-91 RES,CHIP 100K 5% 1/10W <CAPACITOR>

R2813 1-216-089-91 RES,CHIP 47K 5% 1/10W
R2816 1-216-097-91 RES,CHIP 100K 5% 1/10W C654 ! 1-117-703-51 CERAMIC 0.0047MF 99% 250V
R2820 1-216-089-91 RES,CHIP 47K 5% 1/10W C4601 ! 1-136-360-51 FILM 0.22MF 20% 250V
R2821 1-249-412-11 CARBON 390 5% 1/4W F C4602 ! 1-136-360-51 FILM 0.22MF 20% 250V
R2824 1-249-393-11 CARBON 10 5% 1/4W F

R2825 1-216-037-00 RES,CHIP 330 5% 1/10W <CONNECTOR>
R2827 1-216-041-00 RES,CHIP 470 5% 1/10W
R2830 1-215-876-00 METAL OXIDE 15K 5% 1W F CN4601* 1-580-843-11 PIN, CONNECTOR (POWER)
R2831 1-216-462-00 METAL OXIDE 8.2K 5% 2W F CN4602* 1-580-843-11 PIN, CONNECTOR (POWER)
CN4603 1-695-915-11 TAB (CONTACT)
R2833 1-215-893-11 METAL OXIDE 1.5K 5% 2W F
R2834 1-216-462-00 METAL OXIDE 8.2K 5% 2W F
R2837 1-216-041-00 RES,CHIP 470 5% 1/10W <FUSE>
R2838 1-216-069-00 RES,CHIP 6.8K 5% 1/10W
R2839 1-216-081-00 RES,CHIP 22K 5% 1/10W F4601 ! 1-532-299-11 FUSE, TIME-LAG 5A/250V
R2840 1-216-097-91 RES,CHIP 100K 5% 1/10W

R2843 1-216-097-91 RES,CHIP 100K 5% 1/10W <RESISTOR>
R2844 1-216-097-91 RES,CHIP 100K 5% 1/10W
R2846 1-216-059-00 RES,CHIP 2.7K 5% 1/10W R4601 ! 1-202-719-91 SOLID 1M 10% 1/2W
R2847 1-216-049-91 RES,CHIP 1K 5% 1/10W
R2850 1-215-914-11 METAL OXIDE 330 5% 3W F <TRANSFORMER>

R2853 1-215-914-11 METAL OXIDE 330 5% 3W F
R2857 1-216-085-00 RES,CHIP 33K 5% 1/10W T4601 1-431-536-11 TRANSFORMER, LINE FILTER
R2858 1-216-051-00 RES,CHIP 1.2K 5% 1/10W T4602 1-431-182-11 TRANSFORMER, LINE FILTER
R2859 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
R2860 1-216-059-00 RES,CHIP 2.7K 5% 1/10W <VARISTOR>

R2861 1-216-107-00 RES,CHIP 270K 5% 1/10W
R2862 1-216-107-00 RES,CHIP 270K 5% 1/10W VDR461 1-801-073-31 VARISTOR TNR14V471K660
R2866 1-216-073-00 RES,CHIP 10K 5% 1/10W VDR461*!1-801-268-51 COVER, CAPACITOR, CAP TYPE
R2867 1-216-081-00 RES,CHIP 22K 5% 1/10W
R2869 1-216-121-91 RES,CHIP 1M 5% 1/10W

R2871 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
R2872 1-216-057-00 RES,CHIP 2.2K 5% 1/10W ***********************************************************************
R2874 1-216-085-00 RES,CHIP 33K 5% 1/10W
R2877 1-215-905-11 METAL OXIDE 10 5% 3W F
* A-1372-573-A H3 BOARD, COMPLETE (KV-XF29M35)
*********************
<TRANSFORMER> * A-1372-606-A H3 BOARD, COMPLETE (KV-XF29M63/XF29M93)
*********************
T2801 1-424-584-11 TRANSFORMER, DYNAMIC FOCUS
* 4-055-304-01 HOLDER, LED
<CAPACITOR>
***********************************************************************
C3900 1-136-153-00 FILM 0.01MF 5% 50V
C3902 1-136-153-00 FILM 0.01MF 5% 50V
C3904 1-104-664-11 ELECT 47MF 20% 25V
C3905 1-126-965-11 ELECT 22MF 20% 50V
C3906 1-126-965-11 ELECT 22MF 20% 50V
C3907 1-136-175-00 FILM 0.68MF 5% 50V

C3910 1-104-664-11 ELECT 47MF 20% 16V
C3911 1-104-664-11 ELECT 47MF 20% 16V
– 97 –
RM-954
H3 J2
C3912 1-102-114-00 CERAMIC 470PF 10% 50V R3909 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93)
C3913 1-126-960-11 ELECT 1MF 20% 50V R3910 1-249-420-11 CARBON 1.8K 5% 1/4W
C3914 1-126-965-11 ELECT 22MF 20% 50V R3911 1-249-411-11 CARBON 330 5% 1/4W
R3912 1-247-843-11 CARBON 3.3K 5% 1/4W
R3913 1-249-429-11 CARBON 10K 5% 1/4W
<CONNECTOR> R3914 1-249-411-11 CARBON 330 5% 1/4W
R3915 1-249-429-11 CARBON 10K 5% 1/4W
CN3601* 1-580-844-11 PIN, CONNECTOR (POWER)
CN3602* 1-695-292-11 PIN, CONNECTOR (POWER) R3916 1-249-401-11 CARBON 47 5% 1/4W
CN3603 1-695-915-11 TAB (CONTACT) R3917 1-247-804-11 CARBON 75 5% 1/4W
CN3901* 1-564-507-11 PLUG, CONNECTOR 4P R3918 1-247-815-91 CARBON 220 5% 1/4W
R3920 1-247-807-31 CARBON 100 5% 1/4W
CN3903* 1-564-507-11 PLUG, CONNECTOR 4P
CN3905* 1-564-512-11 PLUG, CONNECTOR 9P R3922 1-249-421-11 CARBON 2.2K 5% 1/4W
R3924 1-247-804-11 CARBON 75 5% 1/4W
<DIODE>
<SWITCH>
D3900 8-719-121-26 DIODE RD9.1ESL2
D3901 8-719-121-26 DIODE RD9.1ESL2 S3601 ! 1-571-433-31 SWITCH, PUSH (AC POWER)
D3902 8-719-121-26 DIODE RD9.1ESL2 S3902 1-692-431-21 SWITCH, TACTILE
D3906 8-719-045-19 DIODE SPB-26MVWF S3904 1-692-431-21 SWITCH, TACTILE
S3905 1-692-431-21 SWITCH, TACTILE
D3907 8-719-121-26 DIODE RD9.1ESL2
<IC>
IC3901 8-742-041-12 HYB IC SBX1981-11(12)
***********************************************************************
<JACK>
J3901 1-750-264-11 JACK * A-1388-228-A J2 BOARD, COMPLETE (KV-XF29M35)

J3902 1-784-646-11 TERMINAL, S *********************
J3903 1-770-329-11 JACK, PIN 3P * A-1388-243-A J2 BOARD, COMPLETE (KV-XF29M63/XF29M93)
*********************
<COIL>
L3901 1-408-603-31 INDUCTOR 10UH <CONNECTOR>

L3902 1-408-603-31 INDUCTOR 10UH
L3903 1-406-976-11 INDUCTOR 68UH CN3451* 1-564-518-11 PLUG, CONNECTOR 3P
<TRANSISTOR> <DIODE>
Q3901 8-729-030-02 TRANSISTOR DTC144ESA D3453 8-719-110-72 DIODE RD30ESB2

Q3902 8-729-030-02 TRANSISTOR DTC144ESA D3454 8-719-110-72 DIODE RD30ESB2
<RESISTOR> <JACK>
R3900 1-249-411-11 CARBON 330 5% 1/4W J3451 1-694-467-11 TERMINAL, PUSH (2P)
R3901 1-249-411-11 CARBON 330 5% 1/4W
R3902 1-247-804-11 CARBON 75 5% 1/4W
R3904 1-249-429-11 CARBON 10K 5% 1/4W
R3905 1-249-429-11 CARBON 10K 5% 1/4W
***********************************************************************
R3907 1-249-426-11 CARBON 5.6K 5% 1/4W
R3908 1-249-413-11 CARBON 470 5% 1/4W
R3909 1-249-417-11 CARBON 1K 5% 1/4W
(KV-XF29M35)
– 98 –
RM-954
V1 (KV-XF29M35 ONLY)
* A-1347-155-A V1 BOARD, COMPLETE (KV-XF29M35 ONLY) JR807 1-216-295-91 SHORT 0

********************* JR808 1-216-295-91 SHORT 0
<TRANSISTOR>
<CAPACITOR>
C801 1-104-664-11 ELECT 47MF 20% 16V Q803 8-729-120-28 TRANSISTOR 2SC1623-L5L6
C805 1-163-038-91 CERAMIC CHIP 0.1MF 25V Q805 8-729-120-28 TRANSISTOR 2SC1623-L5L6
C815 1-163-251-11 CERAMIC CHIP 100PF 5% 50V Q807 8-729-120-28 TRANSISTOR 2SC1623-L5L6
C817 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V Q810 8-729-120-28 TRANSISTOR 2SC1623-L5L6
C818 1-163-239-11 CERAMIC CHIP 33PF 5% 50V Q811 8-729-019-01 TRANSISTOR 2SD2394-EF
C820 1-163-239-11 CERAMIC CHIP 33PF 5% 50V Q812 8-729-120-28 TRANSISTOR 2SC1623-L5L6
C823 1-126-933-11 ELECT 100MF 20% 16V Q817 8-729-900-53 TRANSISTOR DTC114EK
C826 1-126-963-11 ELECT 4.7MF 20% 50V Q818 8-729-120-28 TRANSISTOR 2SC1623-L5L6
C831 1-126-933-11 ELECT 100MF 20% 16V <RESISTOR>
C832 1-126-964-11 ELECT 10MF 20% 50V R800 1-216-675-11 METAL CHIP 10K 0.50% 1/10W
C835 1-163-038-91 CERAMIC CHIP 0.1MF 25V R801 1-216-295-91 SHORT 0
C837 1-126-933-11 ELECT 100MF 20% 16V R802 1-216-025-91 RES,CHIP 100 5% 1/10W
R803 1-216-295-91 SHORT 0
R804 1-216-295-91 SHORT 0
<CONNECTOR>
R805 1-216-295-91 SHORT 0
CN801 * 1-774-812-11 CONNECTOR, BOARD TO BOARD 7P R807 1-216-295-91 SHORT 0
CN803 * 1-774-812-11 CONNECTOR, BOARD TO BOARD 7P R813 1-216-295-91 SHORT 0
R820 1-216-073-00 RES,CHIP 10K 5% 1/10W
R821 1-216-083-00 RES,CHIP 27K 5% 1/10W
<DIODE>
R822 1-216-025-91 RES,CHIP 100 5% 1/10W
D802 8-719-914-44 DIODE DAP202K R824 1-216-295-91 SHORT 0
D803 8-719-105-46 DIODE RD3.3M-B2 R825 1-216-295-91 SHORT 0
D804 8-719-105-91 DIODE RD5.6M-B2 R827 1-216-295-91 SHORT 0
D806 8-719-988-61 DIODE 1SS355TE-17 R828 1-216-025-91 RES,CHIP 100 5% 1/10W
D807 8-719-988-61 DIODE 1SS355TE-17
R829 1-216-025-91 RES,CHIP 100 5% 1/10W
R830 1-216-295-91 SHORT 0
R831 1-216-295-91 SHORT 0
<FERRITE BEAD> R832 1-216-659-11 METAL CHIP 2.2K 0.50% 1/10W
R835 1-216-295-91 SHORT 0
FB801 1-410-397-21 FERRITE 1.1UH
FB802 1-410-397-21 FERRITE 1.1UH R839 1-216-655-11 METAL CHIP 1.5K 0.50% 1/10W
FB803 1-410-397-21 FERRITE 1.1UH R841 1-216-025-91 RES,CHIP 100 5% 1/10W
FB804 1-410-682-31 INDUCTOR 470UH R842 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
FB805 1-410-397-21 FERRITE 1.1UH R843 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R844 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
<IC> R845 1-216-049-91 RES,CHIP 1K 5% 1/10W

R846 1-216-049-91 RES,CHIP 1K 5% 1/10W
IC801 8-759-476-87 IC SAA5261 R847 1-216-049-91 RES,CHIP 1K 5% 1/10W
R848 1-216-049-91 RES,CHIP 1K 5% 1/10W
R849 1-216-049-91 RES,CHIP 1K 5% 1/10W
<CHIP CONDUCTOR>
R850 1-216-105-91 RES,CHIP 220K 5% 1/10W
JR801 1-216-295-91 SHORT 0 R851 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
JR804 1-216-295-91 SHORT 0 R857 1-216-081-00 RES,CHIP 22K 5% 1/10W
JR806 1-216-295-91 SHORT 0
– 99 –
RM-954
V1 (KV-XF29M35 ONLY) VM1
R861 1-216-049-91 RES,CHIP 1K 5% 1/10W <CONNECTOR>

R862 1-260-095-11 CARBON 470 5% 1/2W
R863 1-216-049-91 RES,CHIP 1K 5% 1/10W CN2801* 1-564-506-11 PLUG, CONNECTOR 3P
R864 1-216-041-00 RES,CHIP 470 5% 1/10W CN5901* 1-564-510-11 PLUG, CONNECTOR 7P
R866 1-215-880-00 METAL OXIDE 10 5% 2W F CN5904* 1-770-723-11 CONNECTOR, BOARD TO BOARD 8P
R871 1-216-037-00 RES,CHIP 330 5% 1/10W

R879 1-216-073-00 RES,CHIP 10K 5% 1/10W <DIODE>
R880 1-216-041-00 RES,CHIP 470 5% 1/10W
R882 1-216-049-91 RES,CHIP 1K 5% 1/10W D5901 8-719-911-19 DIODE 1SS119-25
R884 1-216-025-91 RES,CHIP 100 5% 1/10W D5902 8-719-110-88 DIODE RD39ESB2
D5903 8-719-911-19 DIODE 1SS119-25
R888 1-216-065-91 RES,CHIP 4.7K 5% 1/10W D5904 8-719-110-88 DIODE RD39ESB2
R889 1-216-073-00 RES,CHIP 10K 5% 1/10W D5905 8-719-911-19 DIODE 1SS119-25
R890 1-216-081-00 RES,CHIP 22K 5% 1/10W
R894 1-216-073-00 RES,CHIP 10K 5% 1/10W D5906 1-249-406-11 CARBON 120 5% 1/4W
R895 1-216-065-91 RES,CHIP 4.7K 5% 1/10W D5907 1-249-406-11 CARBON 120 5% 1/4W
R896 1-216-073-00 RES,CHIP 10K 5% 1/10W

R897 1-216-073-00 RES,CHIP 10K 5% 1/10W <COIL>
R898 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
L5901 1-414-187-11 INDUCTOR 47UH
L5902 1-414-856-11 INDUCTOR 10UH
<CRYSTAL>
X801 1-578-774-11 VIBRATOR, CRYSTAL <TRANSISTOR>
Q5901 8-729-230-45 TRANSISTOR 2SC2458-YGR

Q5902 8-729-017-05 TRANSISTOR 2SA1837
*********************************************************************** Q5904 8-729-119-76 TRANSISTOR 2SA1175-HFE
* A-1342-442-A VM1 BOARD, COMPLETE (KV-XF29M35) Q5906 8-729-017-06 TRANSISTOR 2SC4793

*********************** Q5908 8-729-119-78 TRANSISTOR 2SC2785-HFE
* A-1342-469-A VM1 BOARD, COMPLETE Q5909 8-729-119-78 TRANSISTOR 2SC2785-HFE
(KV-XF29M363/XF29M93)
***********************
<RESISTOR>
4-382-854-11 SCREW (M3X10), P, SW (+) R5901 1-247-815-91 CARBON 220 5% 1/4W

R5902 1-249-414-11 CARBON 560 5% 1/4W F
R5903 1-247-734-11 CARBON 39 5% 1/2W F
<CAPACITOR> R5904 1-249-411-11 CARBON 330 5% 1/4W
R5905 1-249-417-11 CARBON 1K 5% 1/4W
C5902 1-107-883-11 ELECT 330MF 20% 16V (KV-XF29M35)
C5903 1-161-830-00 CERAMIC 0.0047MF 500V
C5905 1-126-925-11 ELECT 470MF 20% 10V R5905 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93)
C5906 1-130-491-00 MYLAR 0.047MF 5% 50V R5906 1-249-417-11 CARBON 1K 5% 1/4W
C5907 1-107-638-11 ELECT 33MF 20% 160V (KV-XF29M35)
R5906 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93)
C5909 1-126-968-11 ELECT 100MF 20% 50V (KV-XF29M35)
C5910 1-130-471-00 MYLAR 0.001MF 5% 50V R5907 1-220-958-91 REGISTER 0 (KV-XF29M63/XF29M93)
C5911 1-107-949-11 ELECT 2.2MF 20% 160V
C5912 1-104-999-11 MYLAR 0.1MF 10% 200V R5908 1-249-383-11 CARBON 1.5 5% 1/4W F
R5909 1-247-815-91 CARBON 220 5% 1/4W
C5913 1-130-471-00 MYLAR 0.001MF 5% 50V R5910 1-249-403-11 CARBON 68 5% 1/4W
C5914 1-126-933-11 ELECT 100MF 20% 16V R5911 1-249-439-11 CARBON 68K 5% 1/4W
C5917 1-126-925-11 ELECT 470MF 20% 10V
C5918 1-115-341-51 CERAMIC 120PF 10% 500V R5914 1-249-403-11 CARBON 68 5% 1/4W
R5915 1-249-429-11 CARBON 10K 5% 1/4W
C5920 1-126-964-11 ELECT 10MF 20% 50V R5916 1-249-419-11 CARBON 1.5K 5% 1/4W
C5921 1-102-852-91 CERAMIC 47PF 5% 50V R5917 1-249-416-11 CARBON 820 5% 1/4W
R5918 1-249-429-11 CARBON 10K 5% 1/4W
– 100 –
RM-954
VM1
R5919 1-249-417-11 CARBON 1K 5% 1/4W F ACCESSORIES AND PACKING MATERIALS

R5920 1-249-439-11 CARBON 68K 5% 1/4W ***************************************
R5921 1-216-476-11 METAL OXIDE 180 5% 3W F
R5922 1-249-414-11 CARBON 560 5% 1/4W 3-701-910-00 SCREW, SPECIAL (DIA. 3.8X20)
R5923 1-249-383-11 CARBON 1.5 5% 1/4W F 3-864-172-31 MANUAL, INSTRUCTION (KV-XF29M35)
3-865-956-11 MANUAL, INSTRUCTION
R5925 1-249-400-11 CARBON 39 5% 1/4W F (KV-XF29M63/XF29M93)
R5929 1-215-880-00 METAL OXIDE 10 5% 2W F * 4-029-168-01 BAG, PROTECTION (KV-XF29M35)
R5930 1-249-413-11 CARBON 470 5% 1/4W * 4-065-594-01 BAG, PROTECTION (KV-XF29M63/XF29M93)
R5931 1-249-413-11 CARBON 470 5% 1/4W
R5932 1-249-413-11 CARBON 470 5% 1/4W * 4-054-319-01 TRAY
4-065-210-01 JOINT
R5933 1-249-413-11 CARBON 470 5% 1/4W * 4-066-924-02 INDIVIDUAL CARTON (KV-XF29M35)
R5934 1-249-430-11 CARBON 12K 5% 1/4W * 4-069-218-01 INDIVIDUAL CARTON (KV-XF29M63/XF29M93)
R5935 1-249-429-11 CARBON 10K 5% 1/4W * 4-066-926-02 CUSHION (UPPER) (ASSY) (KV-XF29M35)
* 4-069-219-01 CUSHION (UPPER) (ASSY)

* 4-066-927-02 CUSHION (LOWER) (ASSY) (KV-XF29M35)
*********************************************************************** * 4-069-220-01 CUSHION (LOWER) (ASSY)
4-392-003-11 BAND, HOLD (KV-XF29M35)
MISCELLANEOUS 4-392-003-31 BAND, HOLD (KV-XF29M63/XF29M93)
*****************
4-392-004-11 CLIP (KV-XF29M35)
! 1-416-495-12 COIL, DEMAGNETIC 4-392-004-21 CLIP (KV-XF29M63/XF29M93)
1-452-032-00 MAGNET,DISC
1-452-094-00 CIRCULAR DISC MAGNET B
1-452-896-11 COIL, NA ROTATION (RT200)
1-529-172-11 SPEAKER, LOUD (10CM) ***********************************************************************
1-529-179-11 SPEAKER (8CM)

1-529-190-11 SPEAKER (5CM) REMOTE COMMANDER
! 1-574-358-11 CORD, POWER (WITH CONNECTOR) 7.5A/250V **********************
(KV-XF29M35)
! 1-574-062-61 CORD, POWER (WITH CONNECTOR) 2.5A/250V 1-418-038-11 REMOTE COMMANDER (RM-954)
(KV-XF29M63/XF29M93) 9-933-895-01 BATTERY COVER, REMOTE COMMANDER
8-451-494-21 DEFLECTION YOKE (Y29RSA-M2)
8-453-011-11 NA299-M
! 8-735-057-05 PICTURE TUBE (M68LNH010X)
! 8-735-056-05 PICTURE TUBE (M68LNH010X) (KV-XF29M63)
***********************************************************************
– 101 –
RM-954
Sony Corporation English

SONY TV Industries (M) Sdn. Bhd. 99AA70082-1
Printed in Malaysia
9-965-720-01 TV Business of General Area  1999. 1
– 102 –

Service Manual: Trinitron Color TV

Uploaded by

Copyright:

Available Formats

Service Manual: Trinitron Color TV

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: Trinitron Color TV

Uploaded by

Copyright:

Available Formats

What are the specifications of the TV?

What are the specifications of the TV?

What are the steps involved in disassembling the TV?

What are the steps involved in disassembling the TV?

Self Diagnosis

SERVICE MANUAL BG-3S CHASSIS

KV-XF29M35 RM-954 OCE SCC-U24A-A

KV-XF29M63 RM-954 India SCC-U22A-A

KV-XF29M93 RM-954 India SCC-U22B-A

Power requirements 110-240 V AC, 50/60 Hz

Design and specifications are subject to change without notice.

CAUTION SAFETY-RELATED COMPONENT WARNING!!

Section Title Page Section Title Page

SELF DIAGNOSIS FUNCTION ................................ 4 5. DIAGRAMS

SELF DIAGNOSTIC FUNCTION

1. DIAGNOSTIC TEST INDICATORS

Diagnostic No. of times Self-diagnostic Probable Detected

Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.

2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT

Lamp ON 0.3 sec.

Diagnostic Item Flash Count*

* One flash count is not used for self-diagnostic.

3. STOPPING THE STANDBY/TIMER FLASH

4. SELF-DIAGNOSTIC SCREEN DISPLAY

[To Bring Up Screen Test]

[Screen display] / channel [5] / Sound volume [-] / Power ON

Self-Diagnosis screen display

5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY

[Clearing the result display]

[Quitting Self-diagnostic screen]

IC301 IC001 IC003

Using Your New TV

Antenna cable (not supplied)

Do not operate the TV if any liquid or solid object : Signal flow

Disconnect the power cord during lightning Audio/Video cable (yellow)

Using Your New TV

Insert the batteries

ONE-PUSH AUTOMATIC PROGRAMMING

AUTO PROGRAM Notes

Now You Are Ready. . .

Using Your New TV 5 6 Using Your New TV

Using Your New TV

Connecting audio/video equipment using the Ú

Using Your New TV

Display the on-screen information* Press .

1 Press MENU. MENU

1 Press U to turn on the TV.

red), press u on the remote press ENTER.

2 Press PROGR +/– or

the TV program. is selected, then press ENTER.

The menu language

Using Your New TV 9 10 Using Your New TV

picture and sound SOUND MODE

1 Press until the

Using Your New TV

To cancel the Wake Up timer

Notes STANDARD receive normal contrast pictures.

Press until the the desired sound mode.

Using Your New TV 11 12 Advanced Operations