Scribd
Upload
44 views3 pages

Tayyab Mujahid 16454 M. Abdullah 17029 M. Bilal Younis

The document describes a digital phase comparator circuit that is well-suited for precision phase measurements at high frequencies. The circuit averages the outputs of two standard phase comparators to measure phase. A clipping circuit with back-to-back Schottky diodes squares up the output pulses for improved linearity. A variable-modulus digital prescaler allows the range to be changed from ±1 to ±32 fringes. The resolution is less than 0.1 degree at 40 MHz with nonlinearity of ~0.5%.

Uploaded by

Moin Abbasi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
44 views3 pages

Tayyab Mujahid 16454 M. Abdullah 17029 M. Bilal Younis

The document describes a digital phase comparator circuit that is well-suited for precision phase measurements at high frequencies. The circuit averages the outputs of two standard phase comparators to measure phase. A clipping circuit with back-to-back Schottky diodes squares up the output pulses for improved linearity. A variable-modulus digital prescaler allows the range to be changed from ±1 to ±32 fringes. The resolution is less than 0.1 degree at 40 MHz with nonlinearity of ~0.5%.

Uploaded by

Moin Abbasi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Tayyab Mujahid 16454

M. Abdullah 17029
M. Bilal Younis

Abstract:
A digital phase comparator has been developed that is especially
well suited to making precision phase measurements at high
frequency. The circuit consists of two standard phase comparators
that are interconnected so that their outputs are averaged to give
the desired phase measurement. A clipping circuit consisting of
back-to-back Schottky diodes is used to square up the output
pulses, which improves the linearity. A variable-modulus digital
prescaler is used to change the range from ±1 fringe to ±32 fringes.
Instruments using this circuitry are being used to measure transient
phase signals from a microwave interferometer that measures the
plasma line density on the magnetic-fusion tandem mirror
experiment. The resolution is less than 0.1 degree at a carrier
frequency of 40 MHz with a maximum nonlinearity of ~0.5%.

Introduction:
A phase detector or phase comparator is a frequency
mixer, analog multiplier or logic circuit that generates a voltage
signal which represents the difference in phase between two signal
inputs. It is an essential element of the phase-locked loop (PLL).
Detecting phase difference is very important in many applications, such
as motor control, radar and telecommunicationsystems, servo mechanisms, and demodulators.

Analog phase detector:


The phase detector needs to compute the phase difference of its
two input signals. Let α be the phase of the first input and β be the
phase of the second. The actual input signals to the phase
detector, however, are not α and β, but rather sinusoids such as
sin(α) and cos(β). In general, computing the phase difference
would involve computing the arcsine and arccosine of each
normalized input (to get an ever-increasing phase) and doing a
subtraction. Such an analog calculation is difficult. Fortunately, the
calculation can be simplified by using some approximations.
Assume that the phase differences will be small (much less than 1
radian, for example). The small-angle approximation for the sine
function and the sine angle addition formula yield:

Circuit Diagram:

Conclusion:
A digital phase comparator has been developed that is especially
well suited to making precision phase measurements at high
frequency. The circuit consists of two standard phase
comparators that are interconnected so that their outputs are
averaged to give the desired phase measurement.

You might also like