To Contents

Oil Pressure Checks 4F27E Gear Ratios

Line Pressure Specifications Rev: 2.65 to 1
1st: 2.82 to 1
Park & Neutral 50—65 Min. 180—210 Max.
2nd: 1.50 to 1
Reverse 65—85 Min. 280—335 Max
3rd: Direct
Drive, 2 ,1 50—65 Min. 180—210 Max.
4th: .73 to 1

Identification
3rd clutch oil
pressure tap

Line Pressure Tap

Need some fresh ideas?

Call our technicians.
626-443-7451

1
Identification Oil Pan

Use Loctite 5699 and no pan gasket.

Install 20 pan bolts to 62 in. lb.
Identification Tag

2
 Identification
Use Mercon V Fluid
Filter and Oil Fill Dry fill is 6.6 liters

Transmission Fluid Temperature

Sensor (TFT) location.

3
Identification Tag
4F27E common Build
characters
Type of
vehicle Level
Bar code

Type of Build Engi- Year and Serial

vehicle Level neering Julian Number
level Date

Tag is on bottom of transmission pan

4
 Complaints and Corrections From: Stone Age Engineer
COMPLAINT: Has 2nd, 4th goes to neutral. Current information can only reach you thru the
QUALIFICATION: This means servo piston is senses of perception-Seeing-Hearing-Tasting-
OK and band is OK. Smelling and Touching. Your brain mixes current
Likely CAUSE: 3-4 solenoid. [Page 18] information with the total of your experience and
Test by swapping Lockup and 3-4 solenoids. forms an opinion. [A guess with common sense]
Your opinion or guess is made 8 times more
COMPLAINT: No 2nd and no 4th. accurate by attaching a pressure gauge. With a
CAUSES: Servo Piston is broken, Band is scanner your opinion will get 4 times more accu-
broken, or 2nd and 4th Solenoid is NG. rate. Both: Is 8x4= 32 times more accurate.
Because a scanner hooks up fast the ten-
QUALIFICATION: Swap 2nd and 4th sol with dency is to use it more and a gauge less.
Forward Sol. 1. A scanner will tell you what the trans should be
Complaint no change: Piston or Band. doing. A gauge tells you what it IS doing.
Complaint changes: Swap the solenoid 2. A gauge will ALWAYS tell when you need a
back to forward and replace 2-4 solenoid. scanner, but a scanner will not always tell you
when you need a gauge.
COMPLAINT: No 3rd-No 3rd hot-Occasional It’s 50 years later and a gauge is still the champ.
no 3rd-2 to 3 or 3 to 2 cutloose. Why is the gauge still the champ?
QUALIFICATION: Place Selector in “D”. Be- Because a gauge will tell you if pressure rise is
tween 1/16 and 3/8 throttle, pressure must go working and scanner will only tell you if it is being
up and down as tho the gauge is attached to commanded. Why is knowing that so Important?
Time, Time, Your time, Shops time and Shops
the gas pedal. [See Pressure rise next page.]
Stress. Time spent working on a slip, shifting or
Pressure Rise is OK: Burned direct clutch lockup is totally wasted until you KNOW pressure
and rings on rear cover ring tower. Page 7. rise is working. [Read 3 times-OUT LOUD]
Pressure not OK: Check electrical. Amps
to EPC does not effect pressure replace EPC. Checking Pressure Rise: Next Page.

5
 Checking Pressure Rise
Never work on a slip, shift or lockup complaint With Selector in “D”: Apply Foot brake, add
without Seeing if Pressure Rise is, or isn't OK. throttle. Pressure should at least double be-
tween idle and just under stall [1500-2500rpm].
Attach Pressure Gauge; Place selector in “D”.
[Exception is Torqueflite which goes up 50%]
Pressure must be above minimum listed for the
trans. If below min, worn pump or very hot, bring With Selector in “D”: While driving 50up mph
RPM up a couple hundred rpm above idle with Lift throttle which should bring pressure to min.
the throttle. If min in “D” and “R” is attained at Then turn the key off momentarily and back on
800 rpm, pump is usually OK even if worn. again. While the key is off pressure should
At idle, or 800 rpm if needed, record the jump instantly to max., then back down to min
pressure in every selector position. when the key is turned back on.
With that record as your reference there is 3
Why Pressure rise is so important?
Questions to ask. 1. Does pressure change by
If it’s not working, low pressure, it will burn
selector range? 2. Does it change with more
clutches with just a few hard throttle shifts.
throttle. 3. does it go max with no Volts?
If it’s not working, high pressure, it’ll burnup
REVERSE: 30 to 50 lbs more than “D”. gear train, for lack of lube, or destroy pump.
When throttle is added, in Reverse, Pressure
Must increase at least another 100 lbs.
[Exceptions all the way are 604—42LE] Ancient Wisdom from
FORWARD: Many trans’s command more pres-
sure in 2 or 1. At idle or prox 800 move selector
Stone Age Engineering
Factory specs are what you use until you find
to 2 and then 1. If pressure goes up either or out what works the best. If you didn’t have
both places, that is evidence that PR is OK. If it factory specs how’d you know where to start?
stays the same it is still OK. If it is less in 2 or 1,
that would indicate a leak to a friction unit.

6
 Internal Parts
Fast Reference Direct & Reverse Rings

Direct Clutch Rev-Low Clutch End Cover

Bench Tech
Hello Bench Technician:
Pay attention to the rings on tower.
These rings wear on the sides.
Side clearance in the groove should not
exceed .005 with feeler gauge.

If the Direct Clutch or the Reverse Low

Clutches are burned suspect these rings.

“Thanks for Listening” Tech Team

Direct and Reverse-Low

Ring Tower

7
 Air Checks
Fast Reference

Place reverse and direct clutch

drum assembly on End Cover.
Then air check the clutch packs
through the holes shown.

Ball Check for

Reverse clutch

Reverse Clutch Direct Clutch

8
 Low One Way Clutch Rotation
When the low one way clutch is installed properly the carrier
Fast Reference assembly will freewheel in the direction of the arrow.

Listen Here

Intermediate/OD Servo Piston

This piston breaks.

Give it new one.
XS4Z-7D0221AB
Ford

9
 Fast Reference Air Checks

Lube orifice

With Pump and Stator bolted

together insert the Forward
drum and then install the
torque converter. Then air
check the locations Shown.
Take it easy, or converter will
blow off the pump.

Need some fresh ideas? Forward

Call our technicians. Clutch TC Front
626-443-7451 TC Rear Releases converter
Applies converter

10
 Fast Reference Air Checks & Band Check
Low & TC TC Forward
Lube #1 Suction Port
Rev. Front Rear clutch Pressure Port

Reverse Drum Servo Apply

Inter/OD Band
2nd & 4th
2nd & 4th Band

Reverse. Direct Clutch

With finger force here band must slide
Clutch Band Release
back and forth on the drum 1/8 to 3/16”.
If band is too loose Weld 1/16 on the end
of the pin or the anchor bolt.
11
Valve Body
Channel Casting: Upper Body

Manual Valve

Low Reverse Valve 1.225x345x30x10

Solenoid Regulator

1.725x346x42x17

12
 Valve Body Main [Lower] Valve Body

Converter Relief 1.660x355x5

TCC Control 1.225x345x30

Main Pressure Regulator

1.425x314x34

Clutch Control

1.225x345x3
3-4 Shift Valve
Solenoid Shift Valve

1.225x345x30
1.400x330x2

13
 Valve Body Section

SSC Accumulator Piston

.91x .438x.059x 8.2

14
 Valve Body Section
Valve Body
Lower valve body side has gasket
Separator Plate bonded to separator plate.

15
Valve Body Valve Body Gaskets are the
same on both sides of the plate.
Valve Body Gaskets

16
 Valve Body Channel Assembly
Low & rev. 1.600”
1.900” clutch seal 1.600”
1.900” 1.900” 1.900” with tip
with tip
1.600”
with tip
1.900”

1.900”
1.900”

1.900”

2.570”

1.600”
with tip
2.570” 1.900”

Servo seal 2.570”

2.570” 1.600”
2.570”
with tip

17
 Valve Body Ford 4F27E Mazda FN4AEL Solenoids
Direct & Band Release 2nd and 4th
Forward SSE Ford SSC Mazda SSD Ford SSB Mazda
SSC Ford SSA Mazda Ford # XS4Z-7G484-AA PWM
“All” C/A,D/B & E/C are the same

Valve Bodies and

Solenoids are fully
Interchangeable
between Ford and
Mazda Units.

NOTICE SEE
NEXT PAGE

Ford # XS4Z-7H148-AA ON-OFF

EPC solenoid Both A/D & B/E are the same
Ford # XS4Z-7G383-AA 3-4 Solenoid Lockup
EPC Solenoid SSA Ford SSD Mazda SSB Ford SSE Mazda

18
 Valve Body Assembly Bolts

1.600” with tip 5 pieces

All bolts are 8mm

Torque to 80 in lbs.
Let’em set a bit, then
loosen and retighten. 1.900” 9 pieces

2.570” 5 pieces

19
Control Lever and Park

Reverse-Low Drum
Check end play here.
.010 to .020

20
 Case

1-2 [2nd]
accm bore.

Neutral to Drive
Accumulator

Inter/OD [2nd & 4th]

Servo Piston

Rubber o-ring

21
 1-2 Accumulator
2.658” x .832” x .138” x 12

2.664” x .519” x .088” x 19

Accumulators
2.937” x .829” x .090” x12.5 N-D Accumulator

2.157” x .612” x .095” x 16

Int and OD Band Piston 8mm bolts 3 pieces

Torque to 80 in lbs.
Intermediate/OD Servo Piston

1.468x1.346x156x4.4

This piston breaks.

Give it new one.
XS4Z-7D0221AB
Ford

22
Control Lever and Parts

23
Control Lever and Parts

8mm Bolts
Torque to 16 FT.LB.

10mm Bolt
Torque to
16 FT. LB.

24
 Valve Body Air Checks & Band Check
Low & TC TC Forward
Lube #1 Suction Port
Rev. Front Rear clutch Pressure Port

Reverse Drum Servo Apply

Inter/OD Band
2nd & 4th
2nd & 4th Band

Fast Reference Reverse. Direct Clutch

Clutch Band Release With finger force here band must slide
back and forth on the drum 1/8 to 3/16”.
If band is too loose Weld 1/16 on the end
of the pin or the anchor bolt.
25
 Valve Body Valve Body to Case Bolts
.800”
1.900” 1.900”

3.090”

3.090

1.900”

1.900”

1.900”

1.900”
1.900” 1.900” 1.900 1.900”
1.900”

26
 Valve Body
Valve Body to Case Bolts
Bolts shown actual size.
The Technology IS the Ethic Bolts are 8mm.
If the sign on the building or any advertising says, Torque to 80 in lbs.
“Transmissions” that is declaration to the Universe
that you know how to fix them.
When a product or service is offered, the offer it- .800” 1 piece
self is a specific claim by the seller that he is ac- Torque to 89 in lbs.
cepting the MORAL and TECHNICAL responsibility
for correct function, for a reasonable length of
time, in exchange for money.
1.900” 11 pieces
Regardless what you may call your repair, the job
is in your shop to have the complaints and failures
corrected. It doesn’t matter how honest you are,
as a person, if you do not fix the causes of the 3.090” 2 pieces
complaints and failures where is the ethic?

Each transmission develops 3 to 5 complaints and

failures you see over and over again and again.

A service is ethical and deserving to the exact ex-

tent that your service corrects the causes of those
complaints and failures; and does not include a
whole bunch of parts that were not needed.

No more and no less, Gil

27
Internal Parts

End Cover

Cover bolts torque to 16 FT.LB

Use Ultra Silicone Sealant or Loctite
Red formagasket under end cover.

28
Internal Parts Internal Parts
Direct & Reverse Rings

Direct Clutch Rev-Low Clutch End Cover

Bench Tech
Hello Bench Technician:
Pay attention to the rings on tower.
These rings wear on the sides.
Side clearance in the groove should not
exceed .005 with feeler gauge.

If the Direct Clutch or the Reverse Low

Clutches are burned suspect these rings.

“Thanks for Listening” Tech Team

Direct and Reverse-Low

Ring Tower

29
Internal Parts Selective Race
Reverse Drum
end play .010-.020

Intermediate/OD band
2nd and 4th End Cover
Bearing runs on
Selective Race.

Reverse/direct clutch
drum assembly

O’ring
O’ring

Rev-Low Clutch Direct Clutch

30
 Internal Parts
Low & Reverse Clutch
.243” pressure plate
.088” selective .089” dish plate
snap ring faces as shown Clutch Packs

5 steel plates and 5 friction plates all measure .064” each. Low & reverse clutch clear-
ance should be .085” - .100”

Low & reverse clutch piston

Inner race low one way clutch Return spring

31
 Internal Parts

Rear planetary carrier

Bearing inner race faces

towards front sun gear.

Low one way

clutch assembly

Front sun gear

Snap ring holds forward

clutch hub in position

Tabs on bearing face down to-

wards front planetary carrier.

Front ring gear

Front planetary carrier

32
Internal Parts

No bearing either side of the

forward clutch hub. Snap
ring on the front sun gear
holds it in position.

33
Internal Parts

Bearing races

Final drive input gear

Bearing

34
Internal Parts

Collapsible spacer
Best if replaced.

Bearing

Torque nut to 330 FT. LB.

35
 Forward Clutch Assembly
Internal Parts
Forward clutch clearance
.035” - .050”

Forward Drum and Shaft

Piston Forward clutch balance piston

Return springs

.064” steel

.064” friction .055” snap ring

.064” friction .064” friction .064” friction
.064” steel .064” steel .235” pressure plate
.064” steel

36
 Internal Parts
Internal Parts

Reverse/direct clutch
drum assembly

Rear sun gear assembly

.064” snap ring

37
Internal Parts
Bearing tab face towards direct Direct clutch hub
clutch hub assembly.

Rear sun gear

assembly

Reverse clutch clearance

.035” - .055”

Bearing inner lip

faces down.

38
 Internal Parts

Low/Reverse Clutch
.227” pressure plate .062” friction
.057” selective
snap ring .064” steel

.062” friction
Reverse clutch clearance
.064” steel .035” - .055”

39
 Internal Parts
Direct Clutch
Direct clutch clearance
should be .055” - .070”
.233” pressure plate .139” steel .139” steel

.063” friction .063” friction

.063” friction
.139” steel

.063” selective
snap ring

40
Internal Parts Direct clutch balance piston
Return springs

Direct Clutch

Direct clutch piston

Direct clutch drum

41
Internal Parts Reverse clutch piston return springs

Reverse Clutch

Reverse clutch piston

Reverse drum assembly

42
 Internal Parts

Forward clutch drum and

input shaft assembly.

.077” black plastic washer

43
Pump
Pump Cover

Need some fresh ideas?

Call our technicians.
626-443-7451

Six 10 mm bolts
Torque to 10 ft lbs.

44
 Pump Assembly
Pump

45
 Pump Assembly
Pump
Oil grooves

Smooth, no groove, side of the outer

gear installs down into the pump.

The inside with the deepest

offset goes into pump first.

46
Bell housing and Differential Area Parts

15 bell housing bolts 10mm

Torque to 16 Ft lbs.

47
 Bell and Differential Housing

Selective shims are under

bearing cups.
Used Bearings:
.005—.010” preload.
New
.010—.015
Case surfaces should be
sealed with Ultra silicon sealant
or Loctite Red Formagasket.

48
Pump and Differential Housing

7 Pump Bolts 10mm

Torque to 16 ft lbs.

49
Differential Housing—Final Drive

50
Park and Drive/Driven Gears

51
 Park Pawl Parts

Torque bolts to 10 FT. LB

Park pawl

Need some fresh ideas?

Call our technicians.
626-443-7451

52
Removing Park Arm

Hold park spring out with a

scribe and use another
scribe to pry out park pin.

53
Final drive gear set.

Final drive.

54
 No washer or bearing goes on either
side of the forward clutch hub. It is
held in place by the snap ring on the
forward sungear.

Need some fresh ideas?

Call our technicians.
626-443-7451

55
Case Connector and Trans Range Sensor

Trans Range Sensor ID

Position Pin with Continuity
Park 5&6 8&9
Reverse 1&4
Neutral 1&8
Drive 1&2
9 5 2nd 1&7
1st 1&3
8 4
9
7 3
8 6
6 2
Case Connector ID
1 Pin Function
7
1 SSE
3
2 PCA
3 SSC
4 TFT return
4
5 TFT
2 6 SSA
5 7 PCA
1 8 SSB
9 SSD

56
NOTICE: Ford and Mazda units both function identically the solenoids are merely named differently...
Solenoids and Valve Bodies interchange freely between the 2 units.

Ford 4F27E Solenoid Firing Order & Friction Application Chart

Shifter Position PCM Commanded Gear Active Solenoids Clutches/Band
Park/Neutral Park/Neutral SSA
Reverse Reverse SSE Rev. & Low Rev.
Drive 1st SSD & SSE Forward & Low One Way
2nd SSE Forward & Int./OD Band
3rd None Forward & Direct
3rd w/TCC SSB & SSC Forward, Direct & TCC
4th SSA & SSC Direct & Int./OD Band
4th w/TCC SSA, SSB & SSC Direct, Int./OD Band & TCC
“1” “1” Manual SSA, SSB & SSE Forward, Low One Way & Low Rev.

SSA and SSB are normally closed and are ON-off solenoids. They measure 10-26 Ω
SSC, SSD and SSE are normally open and are PWM solenoids. They measure 1-4 Ω
Trans Fluid Temperature Sensor 35K Ω at 70 degrees F.

Mazda FN4AEL Solenoid Firing Order & Friction Application Chart

Shifter Position PCM Commanded Gear Active Solenoids Clutches/Band
Park/Neutral Park/Neutral SSD
Reverse Reverse SSC Rev. & Low Rev.
Drive 1st SSB & SSC Forward & Low One Way
2nd SSC Forward & Int./OD Band
3rd None Forward & Direct
3rd w/TCC SSE & SSA Forward, Direct & TCC
4th SSD& SSA Direct & Int./OD Band
4th w/TCC SSD, SSE & SSA Direct, Int./OD Band & TCC
“1” “1” Manual SSD, SSE & SSC Forward, Low One Way & Low Rev.

SSD and SSE are normally closed and are ON-off solenoids. They measure 10-26 Ω
SSA, SSB and SSC are normally open and are PWM solenoids. They measure 1-4 Ω
Trans Fluid Temperature Sensor measures 35K Ω at 70 degrees F.

57
 Valve Body
Ford 4F27E Mazda FN4AEL Solenoids
Solenoids
Direct & Band Release 2nd and 4th
Forward SSE Ford SSC Mazda SSD Ford SSB Mazda
SSC Ford SSA Mazda Ford # XS4Z-7G484-AA PWM
“All” C/A,D/B & E/C are the same

Valve Bodies and

Solenoids are fully
Interchangeable
between Ford and
Mazda Units.

NOTICE SEE
NEXT PAGE

Ford # XS4Z-7H148-AA ON-OFF

EPC solenoid Both A/D & B/E are the same
Ford # XS4Z-7G383-AA 3-4 Solenoid Lockup
EPC Solenoid SSA Ford SSD Mazda SSB Ford SSE Mazda

58
 Solenoids
Solenoid Body
Ford SSC
Mazda SSA

EPC

Ford SSA Ford SSE

Mazda SSD Mazda SSC

Ford SSB
Mazda SSE
Ford SSD
Mazda SSB
Solenoid body plate assembly
Has bonded gaskets

59
 Solenoid Body
Torque solenoid bracket
Torque solenoid body
bolts to 80 in lbs.
bolts to 80 in lbs.

Don’t injure grommet

when removing solenoid.

60
Solenoids

Solenoid Body-Casting

Need some fresh ideas?

Call our technicians.
626-443-7451

61
TSS and OSS Sensors

Gear Ratios
Reverse 2.65 to 1
1st 2.82 to 1
2nd 1.50 to 1
TSS Sensor
3rd direct
4th .73 to 1

OSS Sensor 350 Ω

TSS Sensor 850 Ω

The OSS sensor is larger than the TSS sensor.

Resistance varies some with temperature.

OSS Sensor

Need some fresh ideas?

Call our technicians.
626-443-7451

62
Torque Converter

63
 Abbreviations DCM
DE
Door Control Module
Drive End
A Ampere(s)/Amp(s) Btu British Thermal Units DEC Digital Electronic Controller
ABS Antilock Brake System C Degrees Celsius DERM Diagnostic Energy Reserve Module
A/C Air Conditioning CAC Charge Air Cooler DI Distributor Ignition
AC Alternating Current CAFÉ Corporate Average Fuel Economy dia diameter
ACC Automatic Climate Control Cal Calibration DIC Driver Information Center
ACL Air Cleaner Cam Camshaft Diff Differential
ACR4 Air Conditioning Refrigerant, Recovery, CARB Calif Air Resources Board DK Dark
Recycling, Recharging cc cubic centimeters DLC Data Link Connector
A/D Analog to Digital CCM Central Control Module DMM Digital Multimeter
ADL Automatic Door Lock CCOT Cycling Clutch Orifice Tube DOHC Dual Overhead Camshafts
A/F Air/Fuel Ratio CCP Climate Control Panel DR Driver
AIR Secondary Air Injection CD Compact Disc DRL Daytime Running Lamps
ALC Automatic Level Control CE Commutator End DTC Diagnostic Trouble Code
AM/FM Amplitude Modulation/Frequency CEAB Cold Engine Air Bleed DTM Diagnostic test mode
Modulation CEMF Counter Electromotive Force EBCM Electronic Brake Control Module
Ant Antenna cfm cubic feet per minute EBTCM Electronic Brake & Traction Control Module
AP Accelerator Pedal cg center of gravity EC Electrical Center
API American Protection Institute CID Cubic Inch Displacement ECC Electronic Climate Control
APP Accelerator Pedal Position CKP Crankshaft Position sensor ECI Extended Compressor at Idle
APT Adjustable Part Throttle CKT Circuit ECL Engine Coolant Level
ARS Automatic Restraint System CL Closed Loop ECM Engine Control Module
A/T Automatic Transmission/ Transaxle C/Ltr Cigar Lighter ECS Emission Control System
ATC Automatic Temperature Control CMP Camshaft Position sensor ECT Engine Coolant Temperature
ATDC After Top Dead Center CNG Compressed Natural Gas EEPROM Electronically Erasable Programmable
Auto Automatic CO Carbon Monoxide Read
avg Average CO2 Carbon Dioxide Only Memory
AWD All Wheel Drive Coax Coaxial EEVIR Evaporator Equalized Values in Receiver
AWG American Wire Gage COMM Communication EFE Early Fuel Evaporation
B+ Battery Positive Voltage Conn Connector EGR Exhaust Gas Recirculation
B Battery Negative Voltage CPA Connector Position Assurance EGRTVV Exhaust Gas Recirculation Thermal
BARO Barometric Pressure sensor CPP Clutch Pedal Position Vacuum Valve
batt Battery CPS Central Power Supply EI Electronic Ignition
BBV Brake Booster Vacuum CPU Central Processing Unit ELAP Elapsed
BCM Body Control Module CRT Cathode Ray Tube ELC Electronic Level Control
BHP Brake Horsepower CRTC Cathode Ray Tube Controller E/M English/Metric
BLK Black CS Charging System EMF Electromotive Force
BLU Blue CTP Closed Throttle Position Eng Engine
BOO Brake on / off switch cu ft Cubic foot/feet EOP Engine Oil Pressure
BP Back Pressure cu in Cubic inch/inches EOT Engine Oil Temperature
BPM Brake Pressure Modulator CV Constant Velocity (Joint) EPA Environmental Protection Agency
BPMV Brake Pressure Modulator Valve Cyl Cylinder(s) EPR Exhaust Pressure Regulator
BPP Brake Pedal Position DAB Delayed Accessory Bus EPROM Erasable Programmable Read Only Mem-
BRN Brown DB Decibels on A-weighted Scale ory
BTDC Before Top Dead Center DC Direct Current ESC Electronic Suspension Control
BTSI Brake Transmission Shift Interlock ESD Electrostatic Discharge
ETC Electronic Throttle Control or Electronic
Temperature Control

64
 lt left
ETR Electronically Tuned Receiver HPV High Pressure Vapor
LT Light
EVAP Evaporative Emission Htd Heated
MAF Mass Air Flow
EVO Electronic Variable Orifice HTR Heater
Man Manual
Exh Exhaust HUD Head-up Display
MAP Manifold Absolute Pressure
F Degrees Farenheit HVAC Heater-Vent-Air Conditioning
MAT Manifold Absolute Temperature
FC Fan Control HVACM Heater-Vent-Air Conditioning Module
max maximum
FDC Fuel Data Center HVM Heater Vent Module
M/C Mixture Control
FED Federal (all United States except Calif) Hz Hertz
MDP Manifold Differential Pressure
FEDS Fuel Enable Data Stream IAC Idle Air Control
MFI Multiport Fuel Injection
FF Flexible Fuel IAT Intake Air Temperature
mi mile(s)
FI Fuel Injection IC Integrated Circuit or Ignition Control
MIL Malfunction Indicator Lamp
FMEM Failure management effects mode ICM Ignition Control Module
min minimum
FMVSS Federal Motor Vehicle Safety Stan- ID Identification or Inside Diameter
ml milliliter
dards IDI Integrated Direct Ignition
MLP Manual lever position sensor
F/P Fuel Pump ign ignition
mm millimeter
Ft foot/feet ILC Idle Load Compensator
mpg miles per gallon
FT Fuel Trim in inch(es)
mph miles per hour
F4WD Full Time Four Wheel Drive INJ Injection
ms millisecond
4WAL Four Wheel Antilock inst instantaneous
MST Manifold Surface Temperature
4WD Four Wheel Drive I/P Instrument Panel
M/T Manual Transmission/Transaxle
FW Flat Wire IPC Instrument Panel Cluster
MV Megavolt
FWD Front Wheel Drive I/PEC Instrument Panel Electrical Center
mV millivolt
g gram(s) or Gravitational Acceleration ISC Idle Speed Control
NAES North American Export Sales
GA Gage ISO International Standards Organization
NC Normally Closed
gal gallon(s) ISS Input Speed Shaft
NEG Negative
gas gasoline KAM Keep Alive Memory
Neu Neutral
GCW Gross Combination Weight KDD Keyboard Display Driver
NLGI National Lubricating Grease Institute
Gen Generator kg kilogram
N-m Newton-meter (torque)
GL Gear Lubricant kHZ kilohertz
NO Normally Open
GM General Motors km kilometer
NOx Nitrogen Oxides
GM SPO General Motors Service Parts Opera- km/h kilometers per hour
NPTC National Pipe Thread-Course
tions km/l kilometers per liter
NPTF National Pipe Thread-Fine
gnd ground kPA kilopascals
NVRAM Non-volatile Random Access Memory
gpm gallons per minute KS Knock Sensor
O2 Oxygen
GRN Green kV kilovolts
O2S Oxygen Sensor
GRY Gray L Liter
OBD II On-board Diagnostics II
GVWR Gross Vehicle Weight Rating L4 In-Line Four Cylinder Engine
OC Oxidation Converter (Catalytic)
H Hydrogen L6 In-Line Six Cylinder Engine
OD Outside Diameter
H2O Water lb pound
ODO Odometer
Harn Harness lb ft pound feet (torque)
OE Original Equipment
HC Hydrocarbons lb in pound inch (torque)
OEM Original Equipment Manufacturer
H/CMPR High Compression LCD Liquid Crystal Display
OHC Overhead Camshaft
HD Heavy Duty LDCL Left Door Closed Locking
OL Open Loop
HDC Heavy Duty Cooling LDCM Left Door Control Module
ORN Orange
hex hexagon LED Light Emitting Diode
OSS Output Shaft Speed
Hg Mercury LF Left Front
oz ounce(s)
Hi Alt High Altitude LH Left Hand
PAG Polyalkylene Glycol
HO2S Heated Oxygen Sensor Lm lumens
PASS Passenger
hp horsepower LR Left Rear
HPL High Pressure Liquid
HPS High Performance System

65
P/B Power Brakes RTD Real Time Damping TWC Three-way Converter (Catalytic)
PC Pressure Control RTV Room Temperature Vulcanizing TWC+OC Three-way + Oxidation Converter
PCB Printed Circuit Board (Sealer) (Catalytic)
PCM Powertrain Control Module RWAL Rear Wheel Antilock TXV Thermal Expansion Valve
PCS Pressure Control Solenoid RWD Rear Wheel Drive UART Universal Asynchronous Receive & Transmit
PCV Positive Crankcase Ventilation s second(s) U/H Under Hood
PM Permanent Magnet (Generator) SAE Society of Automotive Engineers U/HEC Under Hood Electrical Center
P/N Part Number SC Supercharger U-Joint Universal Joint
PNK Pink SCB Supercharger Bypass UTD Universal Theft Deterrent
PNP Park/Neutral Position SCM Seat Control Module UV Ultraviolet
PRNDL Park, Reverse, Neutral, Drive, Low SDM Sensing & Diagnostic Module V Volt(s) or Voltage
POA Pilot Operated Absolute (Valve) SEO Special Equipment Option V6 V-type 6 Cylinder Engine
POS Positive SFI Sequential Multiport Fuel Injection V8 V-type 8 Cylinder Engine
POT Potentiometer (Variable Resistor) SI System International (modern version of Vac Vacuum
PPL Purple metric system) VAC Vehicle Access Code
ppm parts per million SIR Supplemental Inflatable Restraint VATS Vehicle Anti-theft System
PROM Programmable Read Only Memory SLA Short/Long Arm VCM Vehicle Control Module
P/S Power Steering sol solenoid VDOT Variable Displacement Orifice Tube
PSD Power Sliding Door SO2 Sulfur Dioxide VDV Vacuum Delay Valve
PSP Power Steering Pressure SP Splice Pack vel velocity
psi pounds per square inch SPO Service Parts Operations VES Variable Effort Steering
psia pounds per square inch absolute sq ft square foot/feet VF Vacuum Fluorescent
psig pounds per square inch guage sq in square inch(es) VIO Violet
pt pint SRC Service Ride Control VIN Vehicle Identification Number
PWM Pulse Width Modulated SRI Service Reminder Indicator VMV Vacuum Modulator Valve
qt quart(s) ST Scan Tool VR Voltage Regulator
R-12 Refrigerant-12 S4WD Selectable Four Wheel Drive V ref Voltage reference
R-134aRefrigerant-134a sw Switch VSS Vehicle Speed Sensor – also called OSS
RAM Random Access Memory (impermanent syn synchronizer sensor
memory device; memory contents lost Tach Tachometer W/ with
when power removed) TB Throttle body W/B Wheel Base
RAP Retained Accessory Power TBI Throttle Body Fuel Injection WHL Wheel
RAV Remote Activation Verification TC Turbocharger WHT White
RCDLR Remote Control Door Lock Receiver TCC Torque Converter Clutch W/o without
RDCM Right Door Control Module TCIL Transmission control indicator lamp WOT Wide Open Throttle
Ref Reference TCS Transmission control switch W/P Water Pump
Rev Reverse TDC Top Dead Center W/S Windshield
RF Right Front or Radio Frequency TEMP Temperature WSS Wheel Speed Sensor
RFA Remote Function Actuation Term Terminal WU-OC Warm-up Oxidation Converter (Catalytic)
RFI Radio Frequency Interference TFP Transmission Fluid Pressure WU-TWC Warm-up Three-way Converter (Catalytic)
RH Right Hand TFT Transmission Fluid Temperature X-valve Expansion Valve
Rly relay TOC Transmission Oil Cooler yd yard(s)
RM Relay module TP Throttle Position YEL Yellow
ROM Read Only Memory (permanent mem- TPA Terminal Positive Assurance
ory TPM Tire Pressure Monitoring
device) TR Transmission Range / Sensor
RPM Revolutions Per Minute—Engine Speed TRANS Transmission/Transaxle
RPO Regular Production Option TSS Turbine shaft sensor
RR Right Rear TVRS Television & Radio Suppression
rt right TVV Thermal Vacuum Valve

66
COMPLETE LIST OF SAE-DEFINED Must use a scan tool connected to
DIAGNOSTIC TROUBLE CODES (DTC): OBD II connector to retrieve codes.
PO1XX Fuel & Air Metering PO153 02 Sensor Circuit Slow Response (Bank 2 *Sensor 1)
PO154 02 Sensor Circuit No Activity Detected (Bank 2 *Sensor 1)
PO100 Mass or Volume Airflow Circuit Problem PO155 02 Sensor Heater Circuit Problem (Bank 2 *Sensor 1)
PO101 Mass or Volume Airflow Circuit Range or Performance Problem PO156 02 Sensor Circuit Problem (Bank 2 *Sensor 2)
PO102 Mass or Volume Airflow Circuit Low Input PO157 02 Sensor Circuit Low Voltage (Bank 2 *Sensor 2)
PO103 Mass or Volume Airflow Circuit High Input PO158 02 Sensor Circuit High Voltage (Bank 2 *Sensor 2)
PO105 Manifold Absolute Pressure or Barometric Pressure Circuit Problem PO159 02 Sensor Circuit Slow Response (Bank 2 *Sensor 2)
PO106 Manifold Absolute Pressure or Barometric Pressure Circuit Range PO160 02 Sensor Circuit No Activity Detected (Bank 2 *Sensor 2)
or Performance Problem PO161 02 Sensor Heater Circuit Problem (Bank 2 *Sensor 2)
PO107 Manifold Absolute Pressure or Barometric Pressure Circuit Low Input PO162 02 Sensor Circuit Problem (Bank 2 *Sensor 3)
PO108 Manifold Absolute Pressure or Barometric Pressure Circuit High Input PO163 02 Sensor Circuit Low Voltage (Bank 2 *Sensor 3)
PO110 Intake Air Temperature Circuit Problem PO164 02 Sensor Circuit High Voltage (Bank 2 *Sensor 3)
PO111 Intake Air Temperature Circuit Range or Performance PO165 02 Sensor Circuit Slow Response (Bank 2 *Sensor 3)
PO112 Intake Air Temperature Circuit Low Input PO166 02 Sensor Circuit No Activity Detected (Bank 2 *Sensor 3)
PO113 Intake Air Temperature Circuit High Input PO167 02 Sensor Heater Circuit Problem (Bank 2 *Sensor 3)
PO115 Engine Coolant Temperature Circuit Problem PO170 Fuel Trim Problem (Bank 1 *)
PO116 Engine Coolant Temperature Circuit Range or Performance Problem PO171 System Too Lean (Bank 1 *)
PO117 Engine Coolant Temperature Circuit Low Input PO172 System Too Rich (Bank 1 *)
PO118 Engine Coolant Temperature Circuit High Input PO173 Fuel Trim Problem (Bank 2)
PO120 Throttle Position Circuit Problem PO174 System Too Lean (Bank 2)
PO121 Throttle Position Circuit Range or Performance PO175 System Too Rich (Bank 2)
PO122 Throttle Position Circuit Low Input PO176 Fuel Composition Sensor Circuit Problem
PO123 Throttle Position Circuit High Input PO177 Fuel Composition Sensor Circuit Range or Performance
PO125 Excessive Time to Enter Closed Loop Fuel Control PO178 Fuel Composition Sensor Circuit Low Input
PO130 02 Sensor Circuit Problem (Bank 1 *Sensor 1) PO179 Fuel Composition Sensor Circuit High Input
PO131 02 Sensor Circuit Low Voltage (Bank 1 *Sensor 1) PO180 Fuel Temperature Sensor Circuit Problem
PO132 02 Sensor Circuit High Voltage (Bank 1 *Sensor 1) PO181 Fuel Temperature Sensor Circuit Range or Performance
PO133 02 Sensor Circuit Slow Response (Bank 1 *Sensor 1) PO182 Fuel Temperature Sensor Circuit Low Input
PO134 02 Sensor Circuit No Activity Detected (Bank 1 *Sensor 1) PO183 Fuel Temperature Sensor Circuit High Input
PO135 02 Sensor Heater Circuit Problem (Bank 1 *Sensor 1)
PO136 02 Sensor Circuit Problem (Bank 1 *Sensor 2) PO2XX Fuel & Air Metering
PO137 02 Sensor Circuit Low Voltage (Bank 1 *Sensor 2)
PO138 02 Sensor Circuit High Voltage (Bank 1 *Sensor 2) PO201 Injector Circuit Problem — Cylinder 1
PO139 02 Sensor Circuit Slow Response (Bank 1 *Sensor 2) PO202 Injector Circuit Problem — Cylinder 2
PO140 02 Sensor Circuit No Activity Detected Bank 1 *Sensor 2) PO203 Injector Circuit Problem — Cylinder 3
PO141 02 Sensor Heater Circuit Problem (Bank 1 *Sensor 2) PO204 Injector Circuit Problem — Cylinder 4
PO142 02 Sensor Circuit Problem (Bank 1 *Sensor 3) PO205 Injector Circuit Problem — Cylinder 5
PO143 02 Sensor Circuit Low Voltage (Bank 1 *Sensor 3) PO206 Injector Circuit Problem — Cylinder 6
PO144 02 Sensor Circuit High Voltage (Bank 1 *Sensor 3) PO207 Injector Circuit Problem — Cylinder 7
PO145 02 Sensor Circuit Slow Response (Bank 1 *Sensor 3) PO208 Injector Circuit Problem — Cylinder 8
PO146 02 Sensor Circuit No Activity Detected (Bank 1 *Sensor 3) PO209 Injector Circuit Problem — Cylinder 9
PO147 02 Sensor Heater Circuit Problem (Bank 1 *Sensor 3) PO210 Injector Circuit Problem — Cylinder 10
PO150 02 Sensor Circuit Problem (Bank 2 *Sensor 1) PO211 Injector Circuit Problem — Cylinder 11
PO151 02 Sensor Circuit Low Voltage (Bank 2 *Sensor 1) PO212 Injector Circuit Problem — Cylinder 12
PO152 02 Sensor Circuit High Voltage (Bank 2 *Sensor 1)

67
PO213 Cold Start Injector 1 Problem PO432 Main Catalyst Efficiency Below Threshold (Bank 2)
PO214 Cold Start Injector 2 Problem PO433 Heated Catalyst Efficiency Below Threshold (Bank 2)
PO434 Heated Catalyst Temperature Below Threshold (Bank 2)
PO3XX Ignition System or Misfire PO440 Evaporative Emission Control System Problem
PO441 Evaporative Emission Control System Insufficient Purge Flow
PO300 Random Misfire Detected PO442 Evaporative Emission Control System Leak Detected
PO301 Cylinder 1 Misfire Detected PO443 Evaporative Emission Control System Purge Control Valve Circuit Problem
PO302 Cylinder 2 Misfire Detected PO444 Evaporative Emission Control System Purge Control Valve Circuit Open
PO303 Cylinder 3 Misfire Detected PO445 Evaporative Emission Control System Purge Control Valve Circuit Shorted
PO304 Cylinder 4 Misfire Detected PO446 Evaporative Emission Control System Vent Control Problem
PO305 Cylinder 5 Misfire Detected PO447 Evaporative Emission Control System Vent Control Open
PO306 Cylinder 6 Misfire Detected PO448 Evaporative Emission Control System Vent Control Shorted
PO307 Cylinder 7 Misfire Detected PO450 Evaporative Emission Control System Pressure Sensor Problem
PO308 Cylinder 8 Misfire Detected PO451 Evaporative Emission Control System Pressure Sensor Range or Performance
PO309 Cylinder 9 Misfire Detected PO452 Evaporative Emission Control System Pressure Sensor Low Input
PO310 Cylinder 10 Misfire Detected PO453 Evaporative Emission Control System Pressure Sensor High Input
PO311 Cylinder 11 Misfire Detected
PO312 Cylinder 12 Misfire Detected PO5XX Vehicle Speed Control & Idle Control System
PO320 Ignition or Distributor Engine Speed Input Circuit Problem
PO321 Ignition or Distributor Engine Speed Input Circuit Range or Performance PO500 Vehicle Speed Sensor Problem
PO322 Ignition or Distributor Engine Speed Input Circuit No Signal PO501 Vehicle Speed Sensor Range or Performance
PO325 Knock Sensor 1 Circuit Problem PO502 Vehicle Speed Sensor Low Input
PO326 Knock Sensor 1 Circuit Range or Performance PO505 Idle Control System Problem
PO327 Knock Sensor 1 Circuit Low Input PO506 Idle Control System RPM Lower Than Expected
PO328 Knock Sensor 1 Circuit High Input PO507 Idle Control System RPM Higher Than Expected
PO330 Knock Sensor 2 Circuit Problem PO510 Closed Throttle Position Switch Problem
PO331 Knock Sensor 2 Circuit Range or Performance
PO332 Knock Sensor 2 Circuit Low Input PO6XX Computer & Output Circuits
PO333 Knock Sensor 2 Circuit High Input
PO335 Crankshaft Position Sensor Circuit Problem PO600 Serial Communication Link Problem
PO336 Crankshaft Position Sensor Circuit Range or Performance PO605 Internal Control Module (Module Identification Defined by J1979)
PO337 Crankshaft Position Sensor Circuit Low Input
PO338 Crankshaft Position Sensor Circuit High Input

PO4XX Auxiliary Emission Controls PO7XX Transmission

PO400 Exhaust Gas Recirculation Flow Problem
PO401 Exhaust Gas Recirculation Flow Insufficient Detected Next Page:
PO402 Exhaust Gas Recirculation Flow Excessive Detected
PO405 Air Conditioner Refrigerant Charge Loss
PO410 Secondary Air Injection System Problem
PO411 Secondary Air Injection System Insufficient Flow Detected
PO412 Secondary Air Injection System Switching Valve or Circuit Problem
PO413 Secondary Air Injection System Switching Valve or Circuit Open
PO414 Secondary Air Injection System Switching Valve or Circuit Shorted
PO420 Catalyst System Efficiency Below Threshold (Bank 1 *)
PO421 Warm-up Catalyst Efficiency Below Threshold (Bank 1 *)
PO422 Main Catalyst Efficiency Below Threshold (Bank 1 *)
PO423 Heated Catalyst Efficiency Below Threshold (Bank 1 *)
PO424 Heated Catalyst Temperature Below Threshold (Bank 1 *)
PO430 Catalyst System Efficiency Below Threshold (Bank 2)
PO431 Warm-up Catalyst Efficiency Below Threshold (Bank 2)
68
PO7XX Transmission
PO730 Incorrect Gear Ratio
PO703 Brake Switch Input Problem
PO731 Gear 1 Incorrect Ratio
PO705 Transmission Range Sensor Circuit Problem (PRNDL Input)
PO732 Gear 2 Incorrect Ratio
PO706 Transmission Range Sensor Circuit Range or Performance
PO733 Gear 3 Incorrect Ratio
PO707 Transmission Range Sensor Circuit Low Input
PO734 Gear 4 Incorrect Ratio
PO708 Transmission Range Sensor Circuit High Input
PO735 Gear 5 Incorrect Ratio
PO710 Transmission Fluid Temperature Sensor Circuit Problem
PO736 Reverse Incorrect Ratio
PO711 Transmission Fluid Temperature Sensor Circuit Range or Performance
PO740 Torque Converter Clutch System Problem
PO712 Transmission Fluid Temperature Sensor Circuit Low Input
PO741 Torque Converter Clutch System Performance or Stuck Off
PO713 Transmission Fluid Temperature Sensor Circuit High Input
PO742 Torque Converter Clutch System Stuck On
PO715 Input or Turbine Speed Sensor Circuit Problem
PO743 Torque Converter Clutch System Electrical
PO716 Input or Turbine Speed Sensor Circuit Range or Performance
PO745 Pressure Control Solenoid Problem
PO717 Input or Turbine Speed Sensor Circuit No Signal
PO746 Pressure Control Solenoid Performance or Stuck Off
PO720 Output Speed Sensor Circuit Problem
PO747 Pressure Control Solenoid Stuck On
PO721 Output Speed Sensor Circuit Range or Performance
PO748 Pressure Control Solenoid Electrical
PO722 Output Speed Sensor Circuit No Signal
PO750 Shift Solenoid A Problem
PO725 Engine Speed Input Circuit Problem
PO751 Shift Solenoid A Performance or Stuck Off
PO726 Engine Speed Input Circuit Range or Performance
PO752 Shift Solenoid A Stuck On
PO727 Engine Speed Input Circuit No Signal
PO753 Shift Solenoid A Electrical
PO706 Transmission Range Sensor Circuit Range or Performance
PO755 Shift Solenoid B Problem
PO707 Transmission Range Sensor Circuit Low Input
PO756 Shift Solenoid B Performance or Stuck Off
PO708 Transmission Range Sensor Circuit High Input
PO757 Shift Solenoid B Stuck On
PO710 Transmission Fluid Temperature Sensor Circuit Problem
PO758 Shift Solenoid B Electrical
PO711 Transmission Fluid Temperature Sensor Circuit Range or Performance
PO760 Shift Solenoid C Problem
PO712 Transmission Fluid Temperature Sensor Circuit Low Input
PO761 Shift Solenoid C Performance or Stuck Off
PO713 Transmission Fluid Temperature Sensor Circuit High Input
PO762 Shift Solenoid C Stuck On
PO715 Input or Turbine Speed Sensor Circuit Problem
PO763 Shift Solenoid C Electrical
PO716 Input or Turbine Speed Sensor Circuit Range or Performance
PO765 Shift Solenoid D Problem
PO717 Input or Turbine Speed Sensor Circuit No Signal
PO766 Shift Solenoid D Performance or Stuck Off
PO720 Output Speed Sensor Circuit Problem
PO767 Shift Solenoid D Stuck On
PO721 Output Speed Sensor Circuit Range or Performance
PO768 Shift Solenoid D Electrical
PO722 Output Speed Sensor Circuit No Signal
PO770 Shift Solenoid E Problem
PO725 Engine Speed Input Circuit Problem
PO771 Shift Solenoid E Performance or Stuck Off
PO726 Engine Speed Input Circuit Range or Performance
PO772 Shift Solenoid E Stuck On
PO727 Engine Speed Input Circuit No Signal
PO773 Shift Solenoid E Electrical

69
 C1102 Acceleration switch circuit failure
Ford OBDII Code Listing C1145
C1155
Wheel speed RF input circuit failure
Wheel speed LF input circuit failure
C1165 Wheel speed RR input circuit failure
B1231 Longitudinal acceleration threshold exceeded C1175 Wheel speed LR input circuit failure
B1318 Battery voltage low C1230 Rear wheel speed sensor input circuit fault
B1342 ECU internal failure C1233 LF wheel speed signal comparison fault
B1342B ECU is defective C1234 RF wheel speed signal comparison fault
B1485 Stop lamp switch input circuit battery short C1235 Speed wheel RR input signal missing
B1676 Battery voltage out of range C1236 Speed wheel RR input signal missing
B1869 Lamp air bag warning indicator circuit open C1237 Rear wheel speed signal comparison fault
B1870 Lamp air bag warning indicator circuit short to battery C1414 Incorrect module design level
B1871 Passenger air bag disable module fault P1000 OBDII drive cycle not complete
B1877 Seatbelt driver pretensioner circuit open P1001 KOER not able to complete, KOER aborted
B1878 Seatbelt driver pretensioner circuit short to battery P1039 Vehicle speed signal missing or improper
B1879 Seatbelt driver pretensioner circuit short to ground P1051 Brake switch signal missing or improper
B1881 Seatbelt passenger pretensioner circuit open P1100 Mass air flow sensor intermittent
B1882 Seatbelt passenger pretensioner circuit short to battery P1101 Mass air flow (MAF) sensor out of self test range
B1883 Seatbelt passenger pretensioner circuit short to ground P1112 Intake air temperature sensor intermittent
B1884 PAD warning lamp inoperative P1116 Engine coolant temperature (ECT) sensor out of self test range
B1885 Seatbelt driver pretensioner circuit resistance low on squib P1117 Engine coolant temperature (ECT) sensor intermittent
B1886 Seatbelt passenger pretensioner circuit resistance low on squib P1118 Manifold air temperature sensor (MAT) (ACT)
B1887 Air bag driver circuit short to ground P1119 Manifold air temperature sensor (MAT) (ACT)
B1888 Air bag passenger circuit short to ground P1120 Throttle position circuit out of range low
B1889 Passenger air bag disable module, module sensor obstructed P1121 Throttle position sensor inconsistent with MAF sensor
B1890 PAD warning lamp circuit short to battery P1124 Throttle position sensor out of self test range
B1891 Air bag tone warning indicator circuit short to battery P1125 Throttle position sensor intermittent
B1892 Air bag tone warning indicator circuit failure P1127 Exhaust not warm enough downstream oxygen sensor not tested
B1900 Driver side air bag fault P1128 Upstream oxygen sensors swapped from bank to bank
B1901 Air bag crash sensor #1 feed/return circuit short to ground P1129 Downstream oxygen sensors swapped from bank to bank
B1916 Air bag driver circuit short to battery P1130 Lack of HO2S11 switch adaptive fuel at limit (bank 1 upstream)
B1921 Air bag diagnostic monitor ground circuit open P1131 Lack of HO2S11 switch sensor indicates lean (Bank 1 upstream)
B1925 Air bag passenger circuit short to battery P1132 Lack of HO2S11 switch sensor indicates rich (Bank 1 upstream)
B1927 Passenger side air bag fault P1133 HO2S11 fuel control shifted lean (Bank 1upstream)
B1932 Air bag driver circuit open P1134 HO2S11 fuel control shifted rich (Bank 1upstream)
B1933 Air bag passenger circuit open P1135 Ignition switch signal missing or improper
B1934 Air bag driver inflator circuit resistance low on squib P1137 Lack of HO2S12 switch sensor indicates lean (Bank 1 downstream)
B1935 Air bag passenger inflator circuit resistance low on squib P1138 Lack of HO2S12 switch sensor indicates rich (Bank 1 downstream)
B1941 Air bag crash sensor #1 feed/return circuit open P1139 Water in fuel circuit malfunction
B2141 NVM configuration failure P1140 Water in fuel condition fail
C1095 Hydraulic pump motor circuit failure

70
P1141 Fuel restriction indicator circuit malfunction P1260 Theft detected – engine disabled
P1142 Fuel restriction switch condition fault P1270 Engine RPM or vehicle speed limiter reach
P1150 Lack of HO2S12 switch adaptive fuel at limit (Bank 2 upstream) P1280 Injection control pressure sensor out of range low
P1151 Lack of HO2S21 switch sensor indicates lean (Bank 2 upstream) P1281 Injection control pressure sensor out of range high
P1152 Lack of HO2S21 switch sensor indicates rich (Bank 2 upstream) P1282 Injection control pressure excessive
P1153 HO2S21 fuel control shifted lean (Bank 2 upstream) P1283 KOEO injection control regulator fail
P1154 HO2S21 fuel control shifted rich (Bank 2 upstream) P1284 KOER fail due to injection control pressure failures
P1157 Lack of HO2S21 switch sensor indicates lean (Bank 2 downstream) P1285 Cylinder head over temperature sensed
P1158 Lack of HO2S21 switch sensor indicates rich (Bank 2 downstream) P1288 Cylinder head temperature sensor out of self test range
P1184 KOER fail engine oil temperature out of self test range P1289 Cylinder head temperature sensor high input
P1190 Throttle position sensor B control circuit malfunction P1290 Cylinder head temperature sensor low input
P1191 Throttle position sensor B out of range P1299 Cylinder head over temperature protection active
P1192 Throttle position sensor circuit low input P1309 Misfire monitor failure
P1193 Throttle position sensor circuit high input P1316 IDM codes detected retrieve IDM codes
P1194 Throttle position sensor B out of self test range P1317 IDM codes not retrieved
P1195 Throttle position sensor B inconsistent P1351 Ignition diagnostic monitor (IDM) circuit malfunction
P1209 Injection control pressure peak delta test fail P1352 Ignition coil A primary malfunction
P1210 Injection control pressure fail maximum pressure test at no-start P1353 Ignition coil B primary malfunction
P1211 KOER fail injection control pressure steady state P1354 Ignition coil C primary malfunction
P1212 Injection control pressure fail minimum pressure test at crank P1355 Ignition coil D primary malfunction
P1220 Throttle position sensor B out of range P1356 PIP’s occurred while IDM pulse width indicates engine not turning
P1224 Throttle position sensor B out of self test range P1357 Ignition diagnostic monitor pulse width not detected
P1227 Waste gate failed closed (Over pressure) P1358 IDM signal out of self test range
P1228 Waste gate failed open (Under pressure) P1359 Spark output circuit malfunction
P1229 Intercooler pump driver fault P1364 Ignition coil circuit malfunction
P1230 Fuel pump low speed malfunction (VLCM) P1369 Engine temperature light monitor failure
P1231 Fuel pump secondary circuit low high speed (VLCM) P1380 Variable cam timing solenoid A malfunction
P1232 Fuel pump secondary circuit high high speed (VLCM) P1381 Variable cam timing over advanced (Bank A)
P1233 Fuel system disabled or offline P1383 Variable cam timing over retarded (Bank A)
P1234 Fuel system failed or offline P1385 Variable cam timing solenoid B malfunction
P1235 Fuel pump control out of range (VLCM) P1386 Variable cam timing over advanced (Bank B)
P1236 Fuel pump control out of range (VLCM) P1388 Variable cam timing over retarded (Bank B)
P1237 Fuel pump secondary circuit malfunction P1389 Glow plug high side out of range low
P1238 Fuel pump secondary circuit malfunction P1390 Octane adjust service pin out of self test range
P1244 Alternator load input failed high P1391 Glow plug Bank #1 out of range high
P1245 Alternator load input failed low P1392 Glow plug Bank #1 out of range low
P1247 Manifold air pressure fail turbocharger hose off P1393 Glow plug Bank #2 out of range high
P1248 Manifold air pressure fail connection hose off P1394 Glow plug Bank #2 out of range low
P1249 Waste-gate fail steady state test P1395 Glow plug monitor fail bank #1 absolute test
P1250 Lack of power to FPRC solenoid P1396 Glow plug monitor fail bank #2 absolute test

71
P1141 Fuel restriction indicator circuit malfunction P1260 Theft detected – engine disabled
P1142 Fuel restriction switch condition fault P1270 Engine RPM or vehicle speed limiter reach
P1150 Lack of HO2S12 switch adaptive fuel at limit (Bank 2 upstream) P1280 Injection control pressure sensor out of range low
P1151 Lack of HO2S21 switch sensor indicates lean (Bank 2 upstream) P1281 Injection control pressure sensor out of range high
P1152 Lack of HO2S21 switch sensor indicates rich (Bank 2 upstream) P1282 Injection control pressure excessive
P1153 HO2S21 fuel control shifted lean (Bank 2 upstream) P1283 KOEO injection control regulator fail
P1154 HO2S21 fuel control shifted rich (Bank 2 upstream) P1284 KOER fail due to injection control pressure failures
P1157 Lack of HO2S21 switch sensor indicates lean (Bank 2 downstream) P1285 Cylinder head over temperature sensed
P1158 Lack of HO2S21 switch sensor indicates rich (Bank 2 downstream) P1288 Cylinder head temperature sensor out of self test range
P1184 KOER fail engine oil temperature out of self test range P1289 Cylinder head temperature sensor high input
P1190 Throttle position sensor B control circuit malfunction P1290 Cylinder head temperature sensor low input
P1191 Throttle position sensor B out of range P1299 Cylinder head over temperature protection active
P1192 Throttle position sensor circuit low input P1309 Misfire monitor failure
P1193 Throttle position sensor circuit high input P1316 IDM codes detected retrieve IDM codes
P1194 Throttle position sensor B out of self test range P1317 IDM codes not retrieved
P1195 Throttle position sensor B inconsistent P1351 Ignition diagnostic monitor (IDM) circuit malfunction
P1209 Injection control pressure peak delta test fail P1352 Ignition coil A primary malfunction
P1210 Injection control pressure fail maximum pressure test at no-start P1353 Ignition coil B primary malfunction
P1211 KOER fail injection control pressure steady state P1354 Ignition coil C primary malfunction
P1212 Injection control pressure fail minimum pressure test at crank P1355 Ignition coil D primary malfunction
P1220 Throttle position sensor B out of range P1356 PIP’s occurred while IDM pulse width indicates engine not turning
P1224 Throttle position sensor B out of self test range P1357 Ignition diagnostic monitor pulse width not detected
P1227 Waste gate failed closed (Over pressure) P1358 IDM signal out of self test range
P1228 Waste gate failed open (Under pressure) P1359 Spark output circuit malfunction
P1229 Intercooler pump driver fault P1364 Ignition coil circuit malfunction
P1230 Fuel pump low speed malfunction (VLCM) P1369 Engine temperature light monitor failure
P1231 Fuel pump secondary circuit low high speed (VLCM) P1380 Variable cam timing solenoid A malfunction
P1232 Fuel pump secondary circuit high high speed (VLCM) P1381 Variable cam timing over advanced (Bank A)
P1233 Fuel system disabled or offline P1383 Variable cam timing over retarded (Bank A)
P1234 Fuel system failed or offline P1385 Variable cam timing solenoid B malfunction
P1235 Fuel pump control out of range (VLCM) P1386 Variable cam timing over advanced (Bank B)
P1236 Fuel pump control out of range (VLCM) P1388 Variable cam timing over retarded (Bank B)
P1237 Fuel pump secondary circuit malfunction P1389 Glow plug high side out of range low
P1238 Fuel pump secondary circuit malfunction P1390 Octane adjust service pin out of self test range
P1244 Alternator load input failed high P1391 Glow plug Bank #1 out of range high
P1245 Alternator load input failed low P1392 Glow plug Bank #1 out of range low
P1247 Manifold air pressure fail turbocharger hose off P1393 Glow plug Bank #2 out of range high
P1248 Manifold air pressure fail connection hose off P1394 Glow plug Bank #2 out of range low
P1249 Waste-gate fail steady state test P1395 Glow plug monitor fail bank #1 absolute test
P1250 Lack of power to FPRC solenoid P1396 Glow plug monitor fail bank #2 absolute test

72
P1397 KOER glow plug test aborted P1502 KOER fail due to auxiliary powertrain control module active
P1399 Glow plug high side out of range high P1504 Idle air control circuit malfunction
P1400 DPFE sensor circuit low voltage detected P1505 Idle air control system at adaptive clip
P1401 DPFE sensor circuit high voltage detected P1506 Idle air control overspeed error
P1403 DPFE sensor hoses reversed P1507 Idle air control underspeed error
P1405 DPFE sensor upstream hose off or plugged P1512 Inlet manifold runner control malfunction (Bank #1 stuck closed)
P1406 DPFE sensor downstream hose off or plugged P1513 Inlet manifold runner control malfunction (Bank #2 stuck closed)
P1407 Exhaust gas recirculation no flow detected P1516 Inlet manifold runner control input error (Bank #1)
P1408 EGR flow out of self test range P1517 Inlet manifold runner control input error (Bank #2)
P1409 EGR control circuit malfunction P1518 Inlet manifold runner control malfunction (stuck open)
P1410 EGR barometric pressure sensor VREF voltage P1519 Inlet manifold runner control malfunction (stuck closed)
P1411 Secondary air injection system incorrect downstream flow detected P1520 Inlet manifold runner control circuit malfunction
P1413 Secondary air injection system monitor circuit low voltage P1525 KOER or cont. mon. fail charge air bypass valve
P1414 Secondary air injection system monitor circuit high voltage P1527 AWS solenoid circuit malfunction
P1442 Evaporative emission control system leak detected (small leak) P1528 PONLY solenoid circuit malfunction
P1443 Evaporative emission control system purge control valve malfunction P1529 SCAIR solenoid circuit malfunction
P1444 Purge flow sensor circuit low input P1530 A/C clutch circuit malfunction
P1445 Purge flow sensor circuit high input P1531 KOER fail pedal position sensor moved
P1450 Unable to bleed up fuel tank vacuum P1536 PBA fail
P1451 Evaporative emission control system vent control valve circuit mal- P1537 Inlet manifold runner control malfunction (bank 2 stuck open)
function P1538 Inlet manifold runner control malfunction (bank 1 stuck open)
P1452 Unable to bleed up vacuum in tank P1539 Power to A/C clutch circuit overcurrent (VLCM)
P1455 Evaporative emission control system purge control leak detected P1540 Air bypass valve circuit malfunction
(gross leak) P1549 Intake manifold communication control circuit malfunction
P1457 Unable to pull vacuum in tank P1550 Power steering pressure switch out of self test range
P1460 Wide open throttle A/C cutout circuit malfunction P1601 ECM/TCM serial communication error
P1461 A/C pressure sensor circuit high input P1602 Imm/TCM serial communication error
P1462 A/C pressure sensor circuit low input P1605 Keep alive memory test fail
P1463 A/C pressure sensor insufficient pressure change P1608 Internal control module malfunction
P1464 KOER A/C clutch fail – A/C demand out of self test range P1610 Flash EPROM reprogramming error
P1469 Low A/C cycling period P1611 Flash EPROM reprogramming error
P1473 Fan secondary high with fan(s) off ( VLCM) P1612 Flash EPROM reprogramming error
P1474 Low fan control primary circuit malfunction P1613 Flash EPROM reprogramming error
P1479 High fan control primary circuit malfunction P1614 Flash EPROM reprogramming error
P1480 Fan secondary low with low fan on P1615 Flash EPROM reprogramming error
P1481 Fan secondary low with high fan on P1616 Flash EPROM reprogramming error
P1484 Open power ground to VLCM (VLCM) P1617 Flash EPROM reprogramming error
P1500 VSS intermittent P1618 Flash EPROM reprogramming error
P1501 KOER fail vehicle speed seen during KOER test P1619 Flash EPROM reprogramming error
P1620 Flash EPROM reprogramming error

73
P1621 Immobilizer code word / ID write failure P1710 Transmission concern
P1622 Immobilizer ID unmatched P1711 KOER fail transmission oil temperature higher or lower than expected
P1623 Immobilizer code word / ID write failure P1713 No change in TFT—low range—TCC problems & harsh shifts
P1625 B+ supply to VLCM fan circuit malfunction (VLCM) P1714 SS1 inductive signature malfunction
P1625 B+ supply to VLCM A/C circuit malfunction (VLCM) P1715 SS2 inductive signature malfunction
P1630 Alternator #1 circuit malfunction P1718 No change in TFT- high range-TCC problems and harsh shifts
P1631 Alternator #2 circuit malfunction P1720 VSS (meter) circuit malfunction
P1634 Data output link failure flag P1727 CCS inductive signature malfunction
P1645 F/P resistor switch circuit malfunction P1728 E4OD converter clutch control excessive slippage
P1650 Power steering pressure switch out of self test range P1729 4x4 fail
P1651 Power steering pressure switch input malfunction P1730 4x4 low error
P1662 KOEO fail injector driver unit relay test P1731 1-2 shift error
P1663 FDCS fail P1732 2-3 shift error
P1667 CI fail P1733 3-4 shift error
P1668 EEC/IDM communications fault P1735 1st gear switch circuit malfunction
P1670 EF fail P1736 2nd gear switch circuit malfunction
P1680 Metering oil pump malfunction P1738 Shift time error
P1681 Metering oil pump malfunction P1740 TCC inductive signature malfunction
P1682 Metering oil pump malfunction P1741 TCC control error
P1683 MOP thermosensor circuit malfunction P1742 TCC mechanical failure solenoid struck on
P1684 MOP position sensor circuit malfunction P1743 LOOP solenoid circuit malfunction
P1685 MOP stepping motor circuit malfunction P1744 Excessive slip across CC
P1686 MOP stepping motor circuit malfunction P1745 Transmission concern
P1687 MOP stepping motor circuit malfunction P1746 PCA solenoid circuit open
P1688 MOP stepping motor circuit malfunction P1747 ETV circuit shorted
P1689 MOP stepping motor circuit malfunction P1748 EPC fail
P1690 KOEO waste gate fail P1749 EPC solenoid failed low
P1691 SPCNT solenoid circuit malfunction P1751 SSB shift solenoid 1 fault
P1692 SEXEC solenoid circuit malfunction P1754 CCS fail
P1693 SINEC solenoid circuit malfunction P1756 SSB shift solenoid 2 fault
P1694 SINLF solenoid circuit malfunction P1760 PCA solenoid intermittent short to ground
P1700 Transmission concern—trans fails to neutral P1761 Shift solenoid C performance
P1701 Reverse engagement error P1762 Transmission concern
P1702 Transmission concern P1765 Solenoid 5 circuit malfunction
P1703 Brake switch out of range P1766 Shift solenoid D performance
P1704 Digital TRS failed to transition state P1767 Transmission concern
P1705 MLPS fail out of range P1770 Clutch solenoid circuit malfunction
P1706 E4OD fail vehicle speed excessive in park P1775 Shift 1 circuit malfunction
P1708 Clutch switch circuit malfunction P1776 Shift 2 circuit malfunction
P1709 PNP switch out of range P1779 OCIL fail
P1780 TCS input incorrect for selected position

74
P1781 4x4 circuit out of range
P1783 Transmission oil temperature over temperature
P1784 Transmission 1st and Reverse mechanical fail
P1785 Transmission 1st and 2nd mechanical failure
P1887 Transmission 3rd or 4th gear electrical fault
P1788 VFS #2 open circuit
P1788b Transmission 2-3 timing or CCS circuit open
P1789 VFS #2 short circuit
P1789b Transmission 2-3 timing or CCS circuit shorted
P1790 TPS (mechanical) circuit malfunction
P1791 TPS (electrical) circuit malfunction
P1792 Atmospheric pressure circuit malfunction
P1793 Intake air volume circuit malfunction
P1794 Battery voltage circuit malfunction
P1795 Idle switch circuit malfunction
P1796 Kick down switch circuit malfunction
P1797 Neutral switch circuit malfunction
P1798 Water thermosensor circuit malfunction
P1799 Hold switch circuit malfunction
P1900 Transmission concern
U1020 Module communications network concern
U1021 SCP indicates lack of A/C clutch status input
U1039 SCP indicates VSS signal missing or incorrect
U1051 SCP indicates brake switch signal missing
U1073 SCP indicates lack of engine coolant fan status
U1131 SCP indicates lack of fuel pump status response
U1135 SCP indicates ignition switch signal missing
U1256 SCP indicates A communications error
U1451 Lack of response at PATS module engine off
U1850 Invalid or missing fuel system data

© TransGo 2005

75