CATIA Tubing and Piping CATIA® V5R19

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Manual Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Tubing and Piping design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Log on/off procedures for Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
To log on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
To logoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pull-down Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Analyze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Tubing Workbench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Tubing Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
General Environment Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Basic Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Routing a Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Select/Query Line ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Route a Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Tubing Display Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Route Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Create an Offset Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Route From a Spline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Modifying Runs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Definition of a Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Aligning parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Segment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Line ID Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Part Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Place Tubing Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Class Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Placing Multiple Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Loose Parts Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Creating Tubing Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

© Wichita State University Table of Contents, Page i

CATIA Tubing and Piping CATIA® V5R19
Part Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Connecting Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Disconnecting Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Offset Segment Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

Manipulating in the Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

Creating a Tubing Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Transfer Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Copy/Paste 3D Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Model Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183

Break Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Validate Run Turns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Adjust Run Extremity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Resize/Respec Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Flip Part Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Move/Rotate Part on the Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204

Flexible Tube Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215

Offset from Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Routing through predefined points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
FLEX algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229

Bundles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Follow Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
Manage Flexible Bundle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
Manage Local Slack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256

Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Manage Flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
Measuring 3D Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Analyze Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Analyze Item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
Validation Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
Report Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286

Piping Design Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293

Pull Down Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Piping Workbench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295

Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297

Creating a PCF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311

Table of Contents, Page ii ©Wichita State University

CATIA Tubing and Piping CATIA® V5R19
Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Problem #1.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Problem #2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
Problem #3.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
Problem #4.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323

Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Equipment & Systems - General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
Design Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
Piping Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334

Appendix B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
Creating a Tubing Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335

Appendix C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
Creating a Piping Tap Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357

© Wichita State University Table of Contents, Page iii

CATIA Tubing and Piping CATIA® V5R19

Introduction
CATIA Version 5 Tubing and Piping Design
Upon completion of this course the student should have a full understanding of the
following topics:

- Creating a run

- Placing Tubing parts

- Managing Tubing connections

- Working with flexible tubes

- Working with flexible Bundles

- Modifying tubes

- Analyzing a tubing system

- Creating a tubing report

- Moving tubing systems in the tree

© Wichita State University Tubing and Piping - Introduction, Page 1

CATIA Tubing and Piping CATIA® V5R19
Manual Format
It is important to understand the format of the manual in order to use it most effectively.
This manual is designed to be used along with an instructor; however, you will need to do a
lot of reading as well, in order to fully understand CATIA Version 5. The exercises in this
book will list steps for you to complete, along with explanations that try to inform you what
you have just done and what you are getting ready to do. The actual steps are in bold type
and the information that follows the steps is for your benefit. Anything that appears in
italics refers to a message CATIA provides—this includes information in pull-down menus,
pop-up windows and other messages.

An example of a step and its explanation is shown below (note: normally the lines will not
be there):

Select a location to the right of the origin. This specifies the other end point of the line.
You will continue specifying locations in order to complete your profile. It should appear
similar to the diagram shown below.

As you can see, the desired action blends in with the text except that it appears in bold. The
information following the step explains what that step accomplished and where you are
going next. It is important to read this information in order to better your understanding of
CATIA Version 5.

Also, you will find that the exercises build upon themselves. Later exercises often assume
you know how to do certain steps which have been covered earlier in the course. If you did
not quite pick up what you needed to know from an exercise, you will probably want to
review it several times before moving onto more advanced sections. The advanced sections
assume that you have a good understanding of the previous sections therefore fewer steps
will be provided. Eventually, you are expected to be able to create parts without any steps.

Tubing and Piping - Introduction, Page 2 ©Wichita State University

CATIA Tubing and Piping CATIA® V5R19

Tubing and Piping design

The Equipment and Systems solution demonstrates how complex models can become
within CATIA. Within this solution there are rules and checks that are automatically
performed. These checks will make sure that parts will fit, or that the appropriate bend
radius is being used, and can automatically add parts like washers and gaskets. The idea is
not just to create compatibility within a tubing system, but to create a tubing design that will
work within a global system. For example Pipes are used to deliver water to a home the
water will need to go into the water heater and then onto the washing machine to wash
clothes. The water heater will be a system all to itself, with water coming in and hot water
leaving. The water heater will also need to create heat, the heat can be created with gas or
electricity, but an energy circuit will need to be defined. How the water heater works might
be designed by an outside company, but the systems going up to it will still need to be
designed. Once the water is heated it will then need to go into the washing machine, a
flexible tube will need to be designed. with the water in the machine it will then need to be
disposed of, a disposal system will need to be designed. To design the water system it could
be necessary to use six or more different workbenches (Space Reservation, Piping,
Equipment reservation, Electrical Part Design, Electrical Harness Assembly, Tubing, Weld
Design...) Before using any of the equipment and systems workbenches it will be helpful to
have a good understanding of Part Design, Generative shape design and Assembly Design;
and a working knowledge of the Catalog Editor.

This book is limited to the Tubing and Piping portions of the Equipment and Systems
solution.

The Tubing and Piping workbenches have many similarities. The icons are very similar and
the process used to create a system is practically the same. There is also some overlap
between the two for work that needs to be done. For these reasons, they are usually taught
at the same time. With the workbenches closely related in design and result, mastering
Tubing will make learning Piping very easy.

Working with Tubing and Piping will involve a lot of rules. The rules will be created at
different levels. Some of the rules can be worked around while others are created by an
administrator and cannot be changed. These rules are meant to speed the design process by
narrowing the options available and limiting the amount of rework necessary. You may find
the rules to be cumbersome at first, as you get used to what they are doing they can become
a useful aide. In this class no rules will be created, the rules that are used are default
CATIA.

© Wichita State University Tubing and Piping - Introduction, Page 3

CATIA Tubing and Piping CATIA® V5R19

Basic Tubing
Working with Equipment and Systems will be much different than other solutions in
CATIA. There will be times that tubing parts will be placed and then tubes will be created
going to them. There will be times that the tubes will need to be placed first and the parts
placed along the tube. The thinking is that tubes will be created as the product is designed
sometimes there will be frame work to work within other times the tube will be placed and
built around. And of course the tubes will have to be modified as the product is revised.

Routing a Run
To place a tube a run will need to be created. A run is the space reservation for a tube to be
placed. The run is NOT a part and cannot be modified outside of the Tubing workbench The
run can be the size of the tube or larger to check for clearances. The run will not carry as
much information as the tube, making it take less space on the computers active memory
and easier to work with. A run can be created between connectors, from a text file, in space,
or by a combination of the three. Once a run is created it can easily be modified; control
points can be added, turn radius can be resized, and branched off of. The run will carry
some of the information for the tube, but the system will not be complete until the tubes are
placed. Placing the tubes into a run is similar to placing Tubing parts in a product. This
will be discussed later.

Open the Routing a Run document from the Routing a Run directory. It should appear
as shown.

If not already there, switch to the Tubing Design workbench. This will allow you to do
all things tube. It is available under the Equipment &Systems solution and the Tubing
Discipline.

© Wichita State University Routing a Run, Page 21

CATIA Tubing and Piping CATIA® V5R19

Flexible Tube Routing

Routing flexible tubes is similar to bendable tubes in the way the connection is made.
However, flexible tubes do not use a run as space reservation. Since there is no run to place
a tube into, the material or type of tube that is being created will be selected during the
routing instead of afterwards. Routing a flexible tube can be done in space, or between
connectors; flexible tubes can be placed on top of a surface, or on top of each other. Flexible
routing will also allow two different solving modes for the route. The use of a standard
algorithm creates a spline, while a flex algorithm can be used to make the tube routing more
accurate with respect to the flexibility of the tube.

Open the Flexible Tubes document from the Flexible Tubes directory. It should appear
as shown.

Define a 0.5 inch Line ID with the Select/Query Line ID icon. You will now create
a number of flexible tubes utilizing the different options available.

© Wichita State University Flexible Tube Routing, Page 215

CATIA Tubing and Piping CATIA® V5R19

Select the Flexible Tube Routing icon. The Flexible Routing window appears.

Standard algorithm Specifies the flexible tubes will be created from standard
splines

FLEX algorithm Specifies the splines will be created with respect to the
flexibility or material properties found in the catalog

Accuracy Modifies the solving mode for computation speed

Flexibility Controls the stiffness of the tube

Uses the material associated with the part

View Opens the properties of the material being used

Operating Temperature Specifies the temperature the tube will be operating at

Operating Pressure Specifies the pressure the tube will be operating at

Torsion Applies a torsion on the tube

Flexible Tube Routing, Page 216 ©Wichita State University

CATIA Tubing and Piping CATIA® V5R19
Swivel Allows the tube to swivel on the connector

Route mode

Select or Indicate Makes routing possible through connectors or

the active plane

Select 3D Point only Routes through 3D points

Select a connector Routes between connectors

Part connector dialog Routing can be done through a dialog box for
any part that has tubing connectors

Bottom offset Puts the bottom of the flexible a set distance

from a specified surface

Center Offset Puts the center of the flexible a set distance

from a specified surface

Follow Tube Allows routing along an existing tube

Change to Schematic mode Switches to schematic mode

Spec driven Allows you to select the Part number based on the specs of the
part

Filter definition Allows you to filter the parts

Part number The type of tube that will be created

Diameter factor A ratio used to determine the bend radius

Bend Radius The minimum curvature allowed in the flexible tube before
failure

Show Spline Shows the spline the flexible tube is following

Build mode

Mode Defines the build mode for the flexible routing

Slack Percent of extra length allowed in the flexible

Length Defines the length of the spline

© Wichita State University Flexible Tube Routing, Page 217

CATIA Tubing and Piping CATIA® V5R19
Bend Creates the flexible with the minimum
length spline necessary

Slack(%) Amount of extra length based on slack

Length: The straight length of the flexible

Straight length at ends Defines the distance at the connection that will remain straight
before the spline will curve

Ignore slack Specifies the slack with be ignored for that section

Start Defines the straight length at the start of the tube

Diameter factor Specifies the straight length will be related to the

diameter of the tube

Length Defines the straight length

End Defines the straight length at the end of the tube

Same as Start length Specifies the end will be the same length as the start

Length Defines the straight length

Flexible Tube Routing, Page 218 ©Wichita State University

CATIA Tubing and Piping CATIA® V5R19
Set the Part number to be TUBE-FLEXIBLE-RUBBER-8S. Turn on the Show Spline
option and set the Build mode to have a 5% slack. The window should appear as shown.
You will use the same settings unless otherwise specified for the rest of the exercise.

Routing with a flexible tube can be similar to routing a bendable tube in that the routing can
be done between connectors.

Select the connector as shown below. Make sure to get the inner connector arrow.

© Wichita State University Flexible Tube Routing, Page 219

CATIA Tubing and Piping CATIA® V5R19
Select the connector on the other side as shown below.

When the second connector is selected, the bundle will automatically be routed. Once the
route has been selected it cannot be canceled. It is in the specification tree and will need to
be deleted if not satisfactory.

Select OK. It should appear as shown below.

This flexible was routed using a standard algorithm. With the standard algorithm there is not
as much control but the routing can be performed faster. If the FLEX algorithm is used then
the model can get much more complicated by taking into account stiffness, temperature,
operating pressure, and gravitational effects.

Flexible Tube Routing, Page 220 ©Wichita State University

 CATIA Tubing and Piping CATIA® V5R19
Offset from Surface
In this section we will cover how to route along a surface or offset from a surface. When
routing with surfaces a point will be created at the location selected, if offset a point will be
made normal to the surface the specified offset at the location selected. The points can be
modified by accessing the part. The spline can be modified by adding tangents or control
points the same way.

Select the Flexible Tube Routing icon. The Flexible Routing window appears.

Select the next green connector on the left.

In the window, select the Center Offset icon to define the Route mode. This will
define an offset between a specified face and the center of the flexible.

Set the Offset to be 0.5. As you mouse over faces in the display, there will be two planes at
the cursor location. The first plane will be tangent to the surface at the point selected. The
second plane will be the offset to the center of the flexible being routed.

Select a point about half way between the two connectors. The offset command will stay
active until it is deselected. If a connector is selected, there will be a space created between
the connector and the middle of the flexible.

Select the Select Connector Only icon and select the connector on the other side.
It should appear as shown.

If you look at a bottom view of the model, you can see that the flexible is offset from the
bottom face 0.5in at the location you selected. When putting a point on a surface a tangent
direction will not be applied. The point is just a passing point. The tangent direction can be
applied later on by going into the definition of the spline.

© Wichita State University Flexible Tube Routing, Page 221

CATIA Tubing and Piping CATIA® V5R19

Select OK. The flexible tube is created.

Select the Flexible Tube Routing icon. The Flexible Routing window appears.

Select the third connector on the left.

Select the next yellow connector on the right on the outside as shown below.

Your flexible tube will go through wall of the tubing box. When routing a flexible tube
often the flexible will go through solid parts. Since there are no alternate routes to be selected
the routing will be modified after the flexible has been created. If the route should go around
an object, then points or routing with an offset will be necessary. Your model should appear
as shown below.

Flexible Tube Routing, Page 222 ©Wichita State University

CATIA Tubing and Piping CATIA® V5R19
The route definition cannot be modified by adding points from this window. If the route
needs to go around the tubing box that needs to be done by adding passing points in the
spline that is controlling the flexible tube. Notice the sharp curve as the flexible turns around
and goes into the connector on the right. That curvature can be problematic as well. By
default the flexible will select a minimum curvature that matches the diameter of the Line ID.
Currently the routing is done with a 0.5in tube and the bend radius is set to 0.5. The values
should be modified before routing if changes need to be made.

The Flexible Routing window will change and offer more information once the route has
been created. In the Build mode section, the Length of the flexible is given along with the
Computed minimum bend radius and the Computed minimum length.

These values cannot be modified, but it is still good information to know.

Select OK. The tube is created.

© Wichita State University Flexible Tube Routing, Page 223

CATIA Tubing and Piping CATIA® V5R19
Routing through predefined points
Since modifying the route cannot be done in the tubing module then modifications will need
to be done at the part level. To go around objects using flexibles there are three options the
first is to use an offset, second is to route through predefined points, the third option is to
modify an existing flexible by adding control points

Double select on the spline in the flexible as shown. This will take make the part level
active, this will do the same thing as double clicking on the part number in the specification
tree.

Double select on the spline again. This will open the spline definition window.

Flexible Tube Routing, Page 224 ©Wichita State University

CATIA Tubing and Piping CATIA® V5R19
This is the same spline definition window that you would see in wireframe and surfaces. If
the route the flexible takes needs to be modified then the spline is what needs to change.

Select Cancel. Points cannot be added from that window. The passing point that the spline
needs to go through will need to be created before the spline can be modified.

Create a point On Plane and select the wall shown the point will be located at H=-5in
and V=-13.75in. This will create a point directly above the connector.

Double select on the spline again. The spline definition window will appear.

© Wichita State University Flexible Tube Routing, Page 225

CATIA Tubing and Piping CATIA® V5R19
When routing flexibles there will be a straight length at the ends by default. This option
creates a minimum straight distance between the flexible and the connector and will be
investigated further later on. Right now it is important to be aware of so that the new routing
point can be placed correctly. The minimum straight distance is a passing point that is a
defined distance normal to the connector. Which means anytime a flexible is routed up to a
connector two routing points will be used.

Select the third point down and select the Add Point Before option. This will place the
point before the straight length going into the last connector.

Select the point that was created. This can be done from the graphical workspace or the
specification tree. The route will update when the selection is made.

Select OK. Your model should look as shown.

Double select on the Flexible Tubes product. This will make the product level active so
that you can continue tubing.

Select the Flexible Tube Routing icon. The Flexible Routing window appears.

Select the next connector on the left on the inside.

In the Flexible Routing window, select the Bottom Offset icon. This option is very
similar to the Center Offset icon, but this will offset from the bottom of the tube instead of
the center.

Set the Offset to be 0.25in.

Flexible Tube Routing, Page 226 ©Wichita State University

CATIA Tubing and Piping CATIA® V5R19
Select the location shown below. Make sure not to select the spline of the other flexible
tube since this will change the direction of the offset.

Select the Select or Indicate icon and select the green connector on the right. The
model should appear as shown below.

The Flexible will be routed so that the bottom of the flexible is .25in from the surface at the
location selected. Since the flexible is following a spline you will want to pay close attention
to the spline definition, adding points on a spline can cause the curve around the spline to be
lower than the point selected.

Select OK. The tube is created.

Select the Flexible Tube Routing icon. The Flexible Routing window appears.

At the bottom of the window change the Length for the Start to be 2.0. This will specify
that the tube must have a 2 inch straight section at the first connector.

Turn the Same as Start length option off and set the Length value to 0.5. The definition
window should appear as shown.

© Wichita State University Flexible Tube Routing, Page 227

CATIA Tubing and Piping CATIA® V5R19

Select the next yellow connector on the left and the next yellow connector on the right.
Take a second to compare the first flexible routed to the last flexible routed.

Both tubes look very similar but their start and end segments differ. Later we will compare
the curves that make up these two tubes to see what their exact differences are.

Select OK.

Flexible Tube Routing, Page 228 ©Wichita State University

CATIA Tubing and Piping CATIA® V5R19
FLEX algorithm
Tubes will flex differently based on the material properties of the materials in them. The
change in flexibility can effect design. When modeling with the Flex algorithm the model
created will more closely resemble what the properties for that type of tube would result in.
When using the FLEX algorithm flexibility can be modified by the flexibility slider or by
applying a material.

Select the Flexible Tube Routing icon. The Flexible Routing window appears.

Select the FLEX algorithm option. With this option selected the Accuracy and Flexibility
sliders will become available along with some additional options.

The flex algorithm incorporates quite a bit of knowledge into the flexible tubes that are
routed. This extra knowledge is an attempt to make the flexible tube as accurate to the actual
tube as possible. With the FLEX algorithm turned on, the tubes will be built with respect to
a selected gravity as well as a defined operating temperature and pressure. You may also
specify that the tube swivels or be in torsion with the connectors.

Slide the Accuracy slider all the way to the right and set the Flexibility slider to be 4.

Change the Straight length at ends to be 0.5 for both ends.

Select the next green connector on the left and the next green connector on the right.
The run will be created and will look different than the first one. The parameters are all the
same but the FLEX algorithm provides a different solution.

Select OK.

Under the Tools pull down menu select Options. Then select the Equipment and Systems
branch and the Design Criteria tab. At the bottom are the flexible routing options.

© Wichita State University Flexible Tube Routing, Page 229

CATIA Tubing and Piping CATIA® V5R19

Select the Gravity in Y-Direction option.

Select OK. The flexible that was created before the gravity was changed will not change
unless it is updated. The change in gravity will not be noticed until a new flexible is created.

Create another flexible tube in exactly the same manner as the last one using the next
set of yellow connectors. It should appear as shown.

The difference is not very noticeable but the change or direction of gravity did affect the new
tube.

Select OK.

Go back to Tools, Options and change the gravity to be in the x-direction.

Flexible Tube Routing, Page 230 ©Wichita State University

CATIA Tubing and Piping CATIA® V5R19
Create another flexible tube between the next two green connectors using the same
parameters as the last two. This time there is a noticeable change.

The tube is laying in the negative x direction. If the tube was supposed to hang in the
positive direction then the value for gravity would need to be positive.

Select OK. The tube is created.

In the specification tree, press the right mouse button on the flexible that was created
with gravity in the y-direction. This will be the last flexible between yellow connectors.
The selection will need to be done in the specification tree to get the correct menu.

Select the FlexTube-XXX.object then select Definition from the contextual menu. The
Definition window should appear. The second tube from the top should also be highlighted.

Select Apply. The flexible will be updated using the gravity in the x-direction.

Select OK.

Select the Flexible Tube Routing icon. The Flexible Routing window appears.

Switch back to Standard algorithm.

Select the yellow connector on the left then the point in the middle and the yellow
connector on the right. Your model should look as shown.

© Wichita State University Flexible Tube Routing, Page 231

CATIA Tubing and Piping CATIA® V5R19

Passing points can be used for routing. Flexibles work differently then bendable tubes. When
using flexibles the route keeps a link to the points. If the point moves the run will need to be
updated and will show the changes. This will also create external references which are
important to keep track of.

Flexible Tube Routing, Page 232 ©Wichita State University

CATIA Tubing and Piping CATIA® V5R19
Your model should look like this.

Save and close your document.

© Wichita State University Flexible Tube Routing, Page 233