Fisher EH and EHA Control Valves PDF

Product Bulletin
51.2:EH
D100042X012
January 2011 EH and EHA Valves
Fisherr EH and EHA Control Valves
W41821
W4589
W97681
Figure 1. Fisher EH and EHA Control Valves
www.Fisher.com
Product Bulletin
51.2:EH
EH and EHA Valves January 2011
Contents Tables
Availability Chart . . . . . . . . . . . . . . . . . . . . . . . . 2
EH Series Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Liquid Flow Coefficients (NPS 8 to 14) . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Available Valve Configurations and Sizes . 13
NPS 1-1/2 x 1 through 6 Globe Valves
Valve Sizes and End Connection Styles . . 13
NPS 3 through 8 Angle Valves . . . . . . . . . . . . . 5 Increased Pressure/Temperature Ratings . 14
Trims (NPS 1-1/2 x 1 through 6 Globe Port Diameters, Valve Plug Travel, Yoke
Valves, NPS 3 through 8 Angle Valves . . 6 Boss Diameters for TSO Trim . . . . . . . . . 14
NPS 8 through 14 Globe Valves . . . . . . . . . . . . . . . 7 Shutoff Classifications . . . . . . . . . . . . . . . . . . 15
Principle of Operation Trim Material Combinations . . . . . . . . . . . . . 18
(NPS 8 through 14 Globe Valves) . . . . . . 8 Construction Materials and Temperature
NPS 20 Globe Valves . . . . . . . . . . . . . . . . . . . . . . . 9 Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . 20
Custom Design Capability Valve Plug Travel (NPS 8 to 14) . . . . . . . . . 22
(NPS 20 Globe Valves) . . . . . . . . . . . . . . 10 Additional Specifications . . . . . . . . . . . . . . . . 26
C-seal Trim Description . . . . . . . . . . . . . . . . . . . . . 11 Yoke Boss and Valve Stem Diameters . . . . 28
Bore Seal Trim Description . . . . . . . . . . . . . . . . . . 11 Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Fisher TSO (Tight Shutoff) Flowing Pressure Drop Limits . . . . . . . . . . . 23
Trim Capabilities . . . . . . . . . . . . . . . . . . . . . . . . 12 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Trim Selection Guidelines . . . . . . . . . . . . . . . . . . . 16 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Material Selection Guidelines . . . . . . . . . . . . . . . . 17 Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Pressure/Temperature Limits . . . . . . . . . . . . . . . . 23 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 1. Availability Chart

Valve Size,
CL1500 CL1500 Intermediate CL2500 CL2500 Intermediate
NPS(1)
1-1/2 x 1 --- --- EHS EHS
2x1 --- --- EHS ---
2 --- --- --- EHD, EHS, EHT
3x2 --- --- EHD, EHS, EHT EHD, EHS, EHT
EHD, EHS, EHT EHD, EHS, EHT
3 EHAT, EHAD EHAD, EHAS, EHAT
EHAD, EHAS, EHAT EHAD, EHAS, EHAT
4x3 --- --- EHD, EHS, EHT ---
6x4 --- --- EHD, EHS, EHT ---
8x6 --- --- EHD, EHS, EHT ---
EHD, EHT, EHD, EHT EHD, EHT
8 EHD, EHT
EHAD, EHAS, EHAT EHAD, EHAS, EHAT EHAD, EHAT
10 x 8 EHD, EHT EHD, EHT EHD, EHT EHD, EHT
12 EHD, EHT EHD, EHT EHD, EHT EHD, EHT
14 --- --- EHD, EHT ---
14 x 12 EHD, EHT EHD, EHT EHD, EHT EHD, EHT
16 x 14 --- --- EHD, EHT ---
20 EHD --- EHD(2) ---
1. Two numbers indicate end connection by nominal valve size. For example, 3 x 2 indicates 3 inch end connection with NPS 2 valve size.
2. CL2185
2
Product Bulletin
51.2:EH
EH (globe) D Increased Pressure/Temperature
Ratings—Steel EH and EHA valves with buttwelding
J EHS (NPS 1-1/2x1 through 8x6), J EHD (NPS 2
end connections have Intermediate Standard
through 20), and J EHT (NPS 2 through 16x14)
Ratings. With nondestructive testing, these valves
can conform to ASME Intermediate Special Ratings,
which allow even higher pressure/temperature
EHA (angle) applications. See tables 7 and 8 for specific ratings.
J EHAS (NPS 3 through 8), J EHAD (NPS 3 D Long Trim Life—Hardened materials of
through 8), and J EHAT (NPS 3 through 8) construction for the cage, valve plug, cage guiding,
and other trim parts are standard for all applications,
providing excellent wear resistance. In all
applications, rugged cage guiding provides
increased valve plug stability. Increased stability
EH Series Valves results in reduced vibration and other mechanical
stresses, which contributes to long trim life.
These valves (figure 1) are specially designed for
high-pressure applications. Fisher EH valve D Piping Economy—The availability of
configurations incorporate proven techniques in expanded end connections on EH valves may
flow-stream contouring for higher capacities and in eliminate the need for line swages while
valve trim design for reliability in severe applications. accommodating oversized piping arrangements.
The temperature limits of EHT valves can be D Control of Low Flow Rates/Tight Shut-off—
extended above 232_C (450_F) by using PEEK Micro-Form or Micro-Flute valve plugs (figure 6 or 7)
(PolyEtherEtherKetone) anti-extrusion rings in provide superb rangeability in high-pressure,
combination with a spring-loaded PTFE seal. The low-flow applications. A choice of several restricted
PEEK anti-extrusion rings expand to close off the port diameters helps match valve capacity to
clearance gap between the plug and the cage where required flow, helps provide necessary control with
the PTFE seal may extrude at high temperatures full travel, and helps prevent throttling near the seat.
and pressures. The temperature limits are extended
to 316_C (600_F) for non-oxidizing service and to For EHA valves only, and in low-flow applications
260_C (500_F) for oxidizing service. where cavitation damage may occur, the Micro-Flat
style valve plug can be used. For low-flow
Unless otherwise noted, all NACE references are to applications where cavitation damage may occur
NACE MR0175-2002. Contact Emerson Process and the minimum required Cv is equal to or greater
Management for information on NACE MR0175/ISO than 0.05, Cavitrolt III with Micro-Flat trim can be
15156 or NACE MR0103. used in both EH and EHA valves. Please contact
your Emerson Process Management sales office for
more information.
For sootblower applications, a special trim design is

Features available to address noise, vibration, tight shutoff,
and thermal cycling which is seen in this application.
D Improved Cage Design—Drilled-hole cages, Please contact your Emerson Process Management
offering excellent strength and additional resistance sales office for more information.
to destructive vibration, are standard. Special
materials of construction are readily available.
D O-ring Seat Ring Gasket Construction—Use D High-Temperature, Class V Shutoff—Use of

of O-ring construction provides excellent shut-off with the metal C-seal (see figure 21) permits Class V
minimal seat ring installation torques for shutoff up to 593_C (1100_F) for up to 4-3/8 inch
temperatures up to 232_C (450_F). O-ring port. The metal Bore Seal trim will permit Class V
construction is standard on EHT valves. The Oring shutoff up 593_C (1100_F) for 5-3/8 inch ports and
seat ring gasket construction is available for larger.
elevated design temperatures and/or NACE
constructions where a suitable Oring material is not D Excellent Stem Sealing—HIGH-SEAL packing
available. systems provide excellent sealing to conserve
3
Product Bulletin
51.2:EH
valuable or hazardous process fluid and to protect Table 2. Liquid Flow Coefficients, Cv, at Maximum Travel
against the emission of hazardous or polluting fluids with Equal Percentage Cage (Modified Equal
to atmosphere. This system (figure 2) features Percentage Characteristic) (NPS 8 through 14 Valves)(1)
graphite packing material and heavy-duty live VALVE PRESSURE VALVE SIZE, NPS
loading. DESIGN RATING 8 and 10x8 12 and 14x12
CL1500 912 1830
PACKING EHD, EHT
BOX
CL2500 584 1010
STUD 1. See the section titled Coefficients in this bulletin for additional sizing data.
SPRING
D Long Thermal-Cycle Life—The seat ring

design minimizes operational stresses, thereby
reducing chances of distortion and resultant leakage
caused by temperature cycling. The hung cage
design allows thermal expansion of the cage without
affecting the seat ring gasket loading.
FOLLOWER
PACKING
D Operational Economy—Balanced trim
constructions reduce forces acting on the valve plug,
thus reducing actuator thrust requirements and
permitting the use of smaller actuators. This,
combined with capacities higher than comparably
priced globe valves, makes the NPS 8 through 14
(including 14x12 and 16x14) EH Series valves very
W5801-3
economical for high-pressure, high-flow service.
Actuator selection for NPS 20 valves can be made
Figure 2. Typical HIGH-SEAL Packing System
from electromechanical or electrohydraulic styles
that use readily available power sources.
SEAT RING SEAT RING SEAT RING SEAT RING
RETAINER RETAINER
D Reliability—All aspects of the control valve
(material selection, trim components, packing, and
control accuracy) are designed, built, and tested to
assure performance and reliability. Extensive
metallurgical evaluation results in state-of-the-art
cage, valve plug, and stem materials that help
ensure trim life and dependable performance.
D Control Accuracy—The NPS 20 cage and

valve plug deliver accurate control of high pressure
VALVE
O-RING VALVE LAMINATED and high capacity flow. Each cage has milled
BODY GRAPHITE
W4434-2* BODY
GASKET
openings and is flow tested for the required flow
characteristic. With precise, accurate cage openings,
O-RING GASKET CONSTRUCTION, LAMINATED GRAPHITE GASKET
accurate installed characteristics result; valves in
STANDARD CONSTRUCTION CONSTRUCTION parallel have the same flow at the same plug
FOR EHT, CAVITROL TRIMS,
1
position. The cone-shaped plug reduces fluid
AND SOUR SERVICE
turbulence, helps ensure plug stability, and aids
NOTES: positioning accuracy.
1 PREFERRED FOR ALL OTHER BODY CONSTRUCTIONS
WHERE TEMPERATURE ALLOWS.
D Easy Maintenance—The bonnet lifts off to
Figure 3. Seat Ring Gasket Constructions allow trim access. The separate seat ring and cage
allow parts removal and maintenance. The globe
D High Capacity—Careful consideration of configuration reduces the uneven trim wear and
aerodynamic and hydrodynamic principles in the resultant maintenance downtime normally associated
design of the flow stream passages results in 30 to with slant configurations. Installation with the stem
40 percent higher capacity than conventional valves vertical above the bonnet also makes trim removal and
with comparable port sizes and travels. installation easy.
4
Product Bulletin
51.2:EH
pressure drop conditions as well as high flow, low
pressure drop conditions. A choice of actuator styles
allows wide selection of power and control
capabilities.
NPS 1-1/2 x 1 through 6 Globe Valves

NPS 3 through 8 Angle Valves
EH Series valves (figure 4) offer higher capacities,
rugged cage guiding, hardened trim materials, and
are available with special trims for noise attenuation
and cavitation abatement. An EH valve package can
be created for specific service conditions from a
variety of special features, including oversized ends,
intermediate ratings, special trim materials, and
special trim configurations.
W3387
Because of flow capacity and severe service

capabilities, both EH and EHA valves are used for
Figure 4. NPS 3 Fisher EH Valve with 657 Actuator many high-pressure applications in process
industries such as power generation, hydrocarbon
production, chemical processing, and refining. The
EHD (figure 5) uses a balanced valve plug and is
well suited for general applications where extremely
tight shutoff is not required. The EHS (figures 6
and 7) has an unbalanced valve plug and provides
up to Class V shutoff. The EHT (figure 8) has a
balanced valve plug and offers up to Class V shutoff
with process temperatures below 232_C (450_F).
EHA valves--EHAD (figure 9), EHAT (figure 10), and

EHAS--are angle versions of the EH valve. Trim is
interchangeable between an EH valve and the next
larger EHA. For example, the trim used in an NPS 3
EHD is the same size as (and is interchangeable
with) the trim in the NPS 4 EHAD.
EH valves are available in CL2500 ratings. EHA

W3379-1 valves are available in CL900, CL1500, and CL2500.
Because these valves feature a thicker body wall,
both EH and EHA valves are available with
Figure 5. Fisher EHD Valve Body Assembly
intermediate ratings. See the Features section in this
bulletin.
D Control Flexibility—Special cage
characterization (standard, Whisper Trimt, or EHA valves provide many of the same features
Cavitrol trim) can be supplied to satisfy almost any available with EH valves. One important feature is
combination of flow and noise or cavitation the availability of special trims for aerodynamic noise
abatement. Cage characterization and efficient flow attenuation, for cavitating liquid service, and for sour
passages provide close control for low flow, high service.
5
Product Bulletin
51.2:EH
Trims (NPS 1-1/2 x 1 through 6 Globe Valves and NPS 3 through 8 Angle Valves)
See figures 6, 7, 8, 9, 10, and 11.
W5028-1
FLOW
W5042-1
FLOW
Figure 9. Fisher EHAD Trim with Whisper Trim III Level D
Figure 6. Fisher EHS Trim with Micro-Form Valve Plug Cage (NPS 3 through 8 Angle Valves)
W5043-1 FLOW
Figure 7. Fisher EHS Trim with Micro-Flute Valve Plug

W5029-1
FLOW
Figure 10. Fisher EHAT Trim with Whisper Trim III

Level D Cage
(NPS 3 through 8 Angle Valves)
FLOW
FLOW
W5041-1
W96711 DIVERTER CONE VALVE PLUG USED FOR FLOWING 'P! 3000 PSI
(207 BAR) OR FOR WHISPER TRIM III LEVEL A, B, OR C CAGES
Figure 8. Fisher EHAT Trim w/ Cavitrol III Trim and Figure 11. Diverter Cone Plug Used in NPS 6 Fisher EHD and
Protected Inside Seat EHT Valves (Flow Up Only)
6
Product Bulletin
51.2:EH
VALVE STEM
GASKETS
CAGE
PISTON RINGS
PIN
VALVE
PLUG
FLOW
SEAT RING
CAP SCREW
GASKET
W44251
SEAT RING
Figure 12. Fisher EHD Valve Assembly (NPS 8 through 14 Globe Valves)
NPS 8 through 14 Globe Valves

EH Series control valves (figure 13) are large,
high-pressure globe valves that incorporate proven
techniques in flow-stream contouring and in seat ring
and valve plug design. These features, along with
rugged cage guiding and hardened trim materials,
make the EH Series valves reliable high-capacity
valves.
These valves are used for many high-pressure

applications in the power, process, oil production,
chemical, refining, and other industries. The EHD
valve (figure 12) is well-suited to general applications
where extremely tight shutoff is not required, and the
EHT valve (figure 14) offers up to Class V shutoff for
applications with relatively low process
temperatures.
W97681
Figure 13. NPS 8 Fisher EH Valve with Welded Pipe

Expanders and 585C Actuator
7
Product Bulletin
51.2:EH
Principle of Operation
(NPS 8 through 14 Globe Valves)
EHD and EHT valves, shown in figures 12 and 14,
are balanced valve designs. When the valves are
opening or closing, pressure registers on top of the
valve plug through the balancing holes in the plug.
The force of the pressure on top of the plug
balances the force of the pressure on the bottom of
the plug to reduce the actuator force required.
RETAINING
RINGS
BACKUP DIVERTER
RING W4430-1 CONE
DIVERTER CONE VALVE PLUG USED IN BOILER

PRESSURE-
ASSISTED
FEEDWATER SERVICE FOR FLOWING 'P! 1000 PSI (69 BAR)
SEAL AND IN OTHER APPLICATIONS FOR FLOWING 'P! 2000 PSI
RING (138 BAR) OR FOR WHISPER TRIM III LEVEL A, B, OR C
CAGES
Figure 16. Diverter Cone Valve Plug Used in Fisher EHD and
EHT Valves (NPS 8 through 14 Globe Valves, Flow Up Only)
SEAT
RING
VALVE
BODY
W4426-1
Figure 14. Fisher EHT Trim (NPS 8 through 14 Globe Valves)

SPIRAL
WOUND
GASKET
SEAT RING
CAP SCREW
SPIRAL WOUND GASKET CONSTRUCTION
(STANDARD CONSTRUCTION FOR HIGH
TEMPERATURE APPLICATIONS)
SEAT
RING
VALVE
BODY
O-RING
SEAT RING
W4429-1 CAP SCREW
O-RING GASKET CONSTRUCTION

(STANDARD CONSTRUCTION FOR SOUR SERVICE AND
OPTIONAL FOR OTHER VALVE CONSTRUCTIONS)
W4428-1 FLOW
Figure 15. Fisher EHD Trim with Whisper Trim III Figure 17. Seat Ring Gasket Constructions
Level D Cage (NPS 8 through 14 Globe Valves) (NPS 8 through 14 Globe Valves)
8
Product Bulletin
51.2:EH
VALVE PLUG
AND STEM
ASSEMBLY
CAGE
FLOW
SEAT RING
W42822
Figure 18. Sectional of NPS 20 Fisher EHD Control Valve Assembly
NPS 20 Globe Valves design features to satisfy specific customer

requirements. For example, figure 18 illustrates a
The NPS 20 EHD control valve (figure 19) is a large, specially characterized cage. Both Whisper Trim
high-pressure, single-port, globe valve designed to cage holes and large cage windows provide the
closely and dependably control high-pressure, customer-required flow characteristic. Additionally,
high-temperature media in the power and the drilled Whisper Trim holes in the cage provide
hydrocarbon industries. For example, NPS 20 EHD noise abatement.
control valves are used in sliding pressure systems
to control high-pressure steam in fossil-fueled power
plants. Standard construction details such as the
cone-shaped valve plug and stem assembly,
Advanced, yet successfully field-proven, the NPS 20 separate seat ring, and HIGH-SEAL packing
EHD control valve usually incorporates special arrangement are also shown in figure 18.
9
Product Bulletin
51.2:EH
A3350/IL
Figure 20. Custom Design Sequence (NPS 20 Globe Valves)
Custom Design Capability (NPS 20 Globe Valves)

Sliding pressure systems, as well as other control
systems, have specific performance characteristics
that require special control valve constructions.
These special constructions must perform
dependably and provide accurate system operation
and plant reliability.
As shown in figure 20, the basic NPS 20 EHD valve
configuration can be designed to meet customer
specifications. Special cage characterization and
actuator/valve response characteristics can be
designed and then confirmed through exhaustive
testing and evaluation. Flow testing of these large
valves takes place at the Emerson Innovation
W41821/IL Center, Fisher Technology, the largest facility of its
kind in North America.
Figure 19. NPS 20 Fisher EHD Valve with
Electromechanical Actuator The final control valve assembly provides reliable,
dependable performance. This performance delivers
controllability for not only the control valve but also
the plant control system, sliding pressure or
otherwise.
10
Product Bulletin
51.2:EH
STAKE THREAD
PISTON
RING
RETAINER
A
C-seal
METAL
PLUG
SEAL(1) VALVE PLUG
FLOW DOWN
RETAINER
C-seal
METAL
PLUG
SEAL(1)
A6869 / IL
C-seal METAL FLOW UP

PLUG SEAL
1
VIEW A
VALVE PLUG CAGE
UPPER SEATING SURFACE
NOTES:
1. REVERSE THE ORIENTATION OF THE C-seal PLUG SEAL FOR PROPER SHUTOFF WHEN VALVE IS USED IN A PROCESS WITH DIFFERENT FLUID FLOW DIRECTION.
Figure 21. C-seal Trim
C-seal Trim Description Bore Seal Trim Description

C-seal trim (figure 21) is available for valves with The Bore Seal design (figure 22) employs a variation
port diameters from 2.875 inches through 4.375 of the proven C-seal trim with enhancements for use
inches. with the larger port EH hung cage. In the Bore Seal
trim, the primary plug-to-seat interface is a
With C-seal trim, a balanced valve can achieve metal-to-metal line contact while the secondary
high-temperature, Class V shutoff. Because the metallic seal engages a controlled bore region in the
C-seal plug seal is formed from metal (N07718 cage when the plug is seated (see figure 22). During
nickel alloy) rather than an elastomer, a valve modulation, the secondary seal does not contact the
equipped with the C-seal trim can be applied in upper cage wall and the controlled bore region
processes with a fluid temperature of up to 593_C remains protected, which extends the shutoff life of
(1100_F). the valve.
11
Product Bulletin
51.2:EH
RETAINER
PISTON RING
CAGE
CAGE
SEATING AREA
SEATING AREA
PLUG
FLOW DOWN BORE SEAL

BORE SEAL
RETAINER
PISTON RING
CAGE
SEATING AREA
PLUG
FLOW UP BORE SEAL
VIEW A
Figure 22. Bore Seal Trim
Fisher TSO (Tight Shutoff) Trim

Capabilities
TSO trim consists of a protected soft seat plus PEEK
anti-extrusion rings with a spring-loaded PTFE plug
seal. Used only in flow down applications, TSO trim
offers unparalleled shutoff integrity, resulting in long
plug and seat life. See figure 23 and tables 9 and 10.
VALVE PLUG For additional information contact your Emerson
SEAL Process Management sales office.
W7020-1
PROTECTED
SOFT SEAT
Figure 23. Typical Balanced TSO (Tight Shutoff) Trim
12
Product Bulletin
51.2:EH
Table 3. Available Globe Valve Configurations and Valve Sizes(1) (NPS 1-1/2 x 1 through 6 Globe Valves)
AVAILABLE CONFIGURATIONS VALVE SIZES (NPS) AND PRESSURE RATING
Valve Valve Plug Cage 1-1/2 x 1, 2 x 1 3x2 3, 4 x 3 4, 6 x 4 6, 8 x 6
Design Style Style CL2500 CL2500 CL2500 CL2500 CL2500
Micro-Form Quick-Opening(2) X X --- --- ---
Standard(3) --- X X X X
EHS Whisper Trim III --- X X X X
Standard Cavitrol III:
2-stage X --- --- --- ---
3-stage --- X --- --- ---
Whisper Trim III --- X X X X
EHT Standard Cavitrol III:
2-stage --- X X X X
3-stage --- --- X X X
EHD Standard
Whisper Trim III --- X X X X
X—Indicates available construction.
1. Two numbers indicate end connection by nominal valve size. For example, 3 x 2 indicates 3 inch end connection with NPS 2 valve size.
2. Linear cage used on NPS 2 and 3 x 2 valves.
3. Standard cages are equal percentage, modified equal percentage, and linear cages.
Table 4. Available Angle Valve Configurations and Valve Sizes (NPS 3 through 8 Angle Valves)
AVAILABLE CONFIGURATIONS VALVE SIZES (NPS) AND PRESSURE RATING
Valve Valve Plug Cage 38 14 6(4)
Design Style Style CL1500 CL2500 CL3230
Micro-Form Quick-Opening(1) X(3) X(3) ---
Micro-Flute Quick-Opening --- --- ---
Standard(2) X X X
EHAS
Whisper Trim III X X X
Standard
Cavitrol III: 2-stage --- --- ---
3-stage --- --- ---
Standard(2) X X X
EHAT Standard
Cavitrol III: 2-stage X X X
3-stage X X X
Standard(2) X X X
EHAD Standard
1. Linear cage used on NPS 2 and 3 valves.
2. Standard cages are equal percentage, modified equal percentage, and linear cages.
3. Not available in NPS 4 and larger.
4. Intermediate CL3230. Contact your Emerson Process Management sales office.
Table 5. Globe Valve Sizes and End Connection Styles(1) (NPS 1-1/2 x 1 through 6 Globe Valves)
VALVE CL2500(2)
SIZE, BWE
NPS SWE RTJ RF
SCH 80 SCH 160 SCH XXS
1-1/2 x 1 X --- X X X X
2x1 X --- X X X X
3x2 X --- X --- X X
3 X --- X --- X X
4x3 X --- X --- X X
4 X --- X --- X X
6x4 X --- X --- X X
6 X --- X --- X X
8x6 X X --- --- X X
1. EN (or other) ratings and end connections can usually be supplied; consult your Emerson Process Management sales office.
2. For valve ratings of EH Series valves with BWE connections, refer to separate bulletin. Increased Pressure/Temperature Ratings for EH Series and EW Series Steel Valves.
13
Product Bulletin
51.2:EH
Table 6. Angle Valve Sizes and End Connection Styles(1) (NPS 3 through 8 Angle Valves)
VALVE CL900 CL1500
SIZE, BWE
NPS RF RTJ SWE RTJ RF
SCH 80 SCH 160 SCH XXS
3 X X X X --- --- X X
4 X X X X --- --- X X
6 X X X X --- --- X X
8 X X X --- X --- X X
1. EN (or other) ratings and end connections can usually be supplied; consult your Emerson Process Management sales office.
Table 7. Increased Pressure/Temperature Ratings for Steel Table 8. Increased Pressure/Temperature Ratings for Steel
Fisher EH Series Globe Valves with Buttwelding Angle Valves with Buttwelding End Connections
End Connections(1) (NPS 3 through 8 Angle Valves)
VALVE CL1500 CL2500 CL1500
VALVE SIZE,
SIZE, Intermediate Rating Intermediate Rating Intermediate Rating
NPS
NPS (ASME B16.34) (ASME B16.34) (ASME B16.34)
1 --- 3862(2) 3 1508
1-1/2 x 1 --- 3021 4 1569
2 --- 3273 6 1804
3 --- 2932 8 1860
4 --- 3294
6 --- 2987
8 1866 2943
10x8 1566 2522
12 1650 2940
14 x 12 1650 2753
1. See bulletin 59.1:026 for additional information.
2. Intermediate rating of 4080 is available with special bolting materials in most
valve body materials. Contact your Emerson Process Management sales office.
Table 9. Port Diameters, Valve Plug Travel, Yoke Boss Diameters for TSO (Tight Shutoff) Trim
MAX TRAVEL YOKE BOSS SIZE PORT DIAMETER CV REDUCTION
VALVE DESIGN TRIM Nominal Actual TSO AT 100%
mm Inch mm Inch mm Inch mm Inch TRAVEL(1)
CAV III 3Stage 90 3-9/16
EHT NPS 6 95.3 3.75 111 4.375 106 4.1875 0%
CL2500 127 5
90 3-9/16 5% (linear)
EHT NPS 6 Std CL2500 76.2 3 111 4.375 106 4.1875
127 5 5% (equal %)
1. This column lists the percent reduction of published maximum CV of the trim listed in the TRIM column.
14
Product Bulletin
51.2:EH
Table 10. Shutoff Classifications per ANSI/FCI 70-2 and IEC 60534-4
Valve Design Port Diameter, mm (Inches) ANSI/FCI Leakage Class
47.6 mm (1.875 inch) and smaller II
II—Standard
58.7 mm (2.3125 inch) to 92.1 mm (3.625 inch)
EHD/EHAD III—Optional
III—Standard
111.1 mm (4.375 inch) and larger
IV—Optional
Valve
Size, Port Diameter, mm (Inches) Cage Style ANSI/FCI Leakage Class
EHD NPS
(CL1500) Eq. %, Mod. Eq. % V to 593_C (1100_F) (for port diameters from
8
177.8 (7) Linear (std. cage) 136.5 through 177.8 mm [5.375 through 7-inches]
10x8
Linear (Whisper III, A1, B3, C3) with optional C-seal or Bore Seal trim)
Eq. %, Mod. Eq. %,
4 Linear (std. cage),
73 (2.875) Linear (Whisper III, A1, B3, C3)
6x4 V (for port
Linear (Cav III, 2-stage) diameters from 73 through 136.5 mm [2.875
Eq. %, Mod. Eq. %, Linear (std. through 5.375 inches] with
EHD 6 cage), Linear (Whisper III, A1, optional C-seal trim)
111.1 (4.375) B3, C3, D3)
(CL2500) 8x6
Linear (Cav III, 2- and 3-stage)
8
136.5 (5.375) Eq. %, Mod. Eq. %, Linear (std. V to 593_C (1100_F) (for port diameters from
10x8
cage), Linear (Whisper III, A1, 136.5 through 177.8 mm [5.375 through 7-inches]
12 with optional Bore seal trim)
177.8 (7) B3, C3, D3)
14x12
EHS, EHAS, EHT, EHAT All Cavitrol III V
Std or w/ Micro-Form or IV—Standard,
EHS, EHAS, EHT, EHAT All
w/ Micro-Flute V—Optional
TSO - Optional
TSO is not an ASME leakage class.
Valves with TSO trim are factory tested to a more
EHT w/ TSO (Tight Shutoff) See table 9 See table 9 stringent Fisher test requirement of no leakage at
time of shipment. Test medium is water. Specify
service 'P when ordering. Test procedure is
ANSI/FCI Class V test procedure B.
EHT w/ PEEK(1) 25.4 mm (1- inch) to 254 mm
All V to 316_C (600_F)
Anti-Extrusion Rings (10- inch)
1. PEEK (PolyEtherEtherKetone)
15
Product Bulletin
51.2:EH
Trim Selection Guidelines for D Trim 53—Trim 53 should be used in all high
temperature applications between 427_C (800_F)
NPS 1-1/2 x 1 through 6 Globe and and 566_C (1050_F) unless chlorides are present.
NPS 3 through 8 Angle Valves The presence of chlorides could lead to stress
corrosion cracking of the CA28MWV (422 stainless
Please refer to the following descriptions as a steel) cage.
guideline for the selection of appropriate trims:
D Trim 54—Trim 54 is the standard trim for
stainless steel body materials. It should be used
D Trim 49—Trim 49 is the standard trim for C12A where hard-faced trim is specified.
valve body materials and should only be used with
C12A valve body materials. C12A should only be Trim 54 should not be used in boiler feedwater due
used when the pressure and temperature to amine corrosion problems associated with
capabilities for WC9 valve body materials are not CoCr-A.
acceptable.
D Trim 56—Trim 56 should be used for sour
service.
D Trim 50—Trim 50 is the standard trim for
carbon steel and alloy steel body materials and is D Trim 57—Trim 57 should be used for boiler
recommended for general and severe service feedwater service when limits exceed those
applications up to 427_C (800_F). Typical specified for Trim 50.
applications for Trim 50 include services in water,
boiler feedwater, non-sour hydrocarbons, and steam. Care should be taken when specifying this trim in
The S41600 (416 stainless steel) heat-treated plug small sizes for applications where chlorides are
and seat ring have a hardness similar to CoCr-A present due to stress corrosion cracking problems
(Alloy 6). with S44004 (440C stainless steel).
16
Product Bulletin
51.2:EH
WCC STEEL VALVES LCC STEEL VALVES CF8M (316 OR 316H ABOVE
THE LCC LOWER LIMIT CAN BE EXTENDED 538qC [1000qF])
TO 46_C (50_F) WITH IMPACT TESTING
STAINLESS STEEL VALVES
TYPICAL FOR ALL GRAPHS
CL2500
CL1500
CL900
WC9 CHROME-MOLY STEEL VALVES C12A VALVES

NOTE:
DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE PRESSURE RATING OF THE BODY MATERIAL AND VALVE SIZE
USED. REFER TO TABLES 3 AND 4 FOR PRESSURE/TEMPERATURE LIMITS OF THE TRIM USED. INTERMEDIATE PRESSURE/ TEMPERATURE
RATINGS ARE FOUND IN SEPARATE BULLETIN, INCREASED PRESSURE/TEMPERATURE RATINGS FOR EH AND EW SERIES STEEL VALVES.
B1960-1*
Figure 24. Pressure/Temperature Limits for CL2500 Valves (NPS 1-1/2 x 1 through 6 Globe)
and CL900, 1500, and 2500 Valves (NPS 3 through 8 Angle)
Material Selection Guidelines temperature capabilities determined from figures 24,

25, 26, and 27 may be further limited by the
Please use these numbered steps as a guideline for temperature capabilities of materials selected from
the selection of materials: tables 11, 12, 13, and 14. Refer to figures 24, 25, 26,
and 27 to determine pressure drop limits of the
1. Determine the pressure/temperature rating of the body-trim combinations selected.
valve size and material required. Inlet pressure and
temperature must always be limited by the
applicable ASME pressure/temperature rating.
Inlet pressure and temperature must always be
2. Select the desired valve style from the Available limited by the applicable ASME pressure/
Configurations specification and from the shutoff temperature rating. Contact your Emerson Process
classifications listed in table 10. Management sales office for special materials for
temperatures exceeding the following maximum
3. Select desired materials from tables 11, 12, 13, limits: EHD valve [593_C (1100_F)] and the EHT
and 14 and figures 24, 25, 26, and 27. The valve [232_C (450_F)].
17
Product Bulletin
51.2:EH
Table 11. Trim Material Combinations (NPS 1-1/2 x 1 through 6 Globe and NPS 3 through 8 Angle Valves)
OPERATING
TEMPERATURE RANGE SOUR
SEAT RING
DESIGNATION VALVE PLUG CAGE SEAT RING SERVICE
RETAINER Degrees Degrees
(NACE)
Celsius Fahrenheit
WITH STANDARD CAGE
S41600 (416 SST)
heat-treated(2)
S17400 (17-4PH S17400
S44004 (440C SST) S41600
50(1) SST) H1075 heat- H1150 heat-treated 29 to 427 20 to 800 No
heat-treated for heat-treated
treated chrome coat
Micro-Flute valve
plugs
53(3)
(EHD/ S31600 (316 SST) CA28MWV N07718
EHAD and EHS/ with CoCr-A (Alloy 6) (422 SST) CoCr-A heat-treated 427 to 566 800 to 1050 No
EHAS valves seat and guide nitrided chrome coat
only)
S31600 N07718
CF8M (316 SST)
54 with CoCr-A CoCr-A heat-treated 38 to 593 100 to 1100 No
chrome coat
seat and guide chrome coat
S17400
S31600
CF8M H1150
56 with CoCr-A CoCr-A(4) 40 to 149 40 to 300 Yes
ENC heat-treated
seat and guide
chrome coat
S17400
57 S17400
S44004 S44004 H1150
(O-ring seat H1075 0 to 232 32 to 450 No
heat-treated heat-treated heat-treated
ring only) heat-treated
chrome coat
F22 with CoCr-A N07718 heattreated
49 F22 nitrided CoCrA 29 to 593 20 to 1100 No
WITH CAVITROL III TRIM CAGE
S17400
CB7CU-1
S44004 H1150
58(1) H1075 S44004(4) 0 to 232 32 to 450 No
heat-treated heat-treated
heat-treated
chrome coat
S17400
S31600 CB7CU-1
H1150
59 with CoCr-A H1150 CoCr-A(4) 40 to 232 40 to 450 Yes
heat-treated
seat and guide heat-treated
chrome coat
WITH WHISPER TRIM III CAGE
S41600
heat-treated
S17400
S17400 CB7CU-1
S41600 H1150
60 (17-4H900 SST) H1075 29 to 427 20 to 800 No
heat-treated heat-treated
heat-treated for heat-treated
chrome coat
NPS 6 EH and NPS 8
EHA valves
CA28MWV
S31600 nitrided N00718
61 with CoCr-A WC9 nitrided CoCr-A heat-treated 29 to 566 20 to 1050 No
seat and guide for NPS 6 EH and chrome coat
NPS 8 EHA valves
S17400
S31600 CB7CU-1
H1150
62 with CoCr-A H1150 CoCr-A(4) 40 to 232 40 to 450 Yes
heat-treated
seat and guide heat-treated
chrome coat
F22 with CoCr-A N07718 heattreated
63 F22 nitrided CoCrA 29 to 593 20 to 1100 No
1. Recommended for boiler feedwater service due to amine problems when using Alloy 6.
2. 17-4H900 stainless steel heat-treated is used when a diverter cone valve plug is specified for port diameters equal to and larger than 4.375 inches.
3. This trim designation not available with the O-ring seat ring gasket construction due to temperature limitations.
4. This trim designation uses the O-ring seat ring gasket construction. See table 13 for O-ring temperature limits.
18
Product Bulletin
51.2:EH
Table 12. Trim Material Combinations (NPS 8 through 14 Fisher EHD and EHT)
OPERATING
TRIM VALVE PLUG SEAT RING TEMPERATURE RANGE
VALVE PLUG CAGE SEAT RING
DESIGNATION STEM CAP SCREWS
_C _F
EHD and EHT Valve with Standard Cage
S17400
S42000 S31600
75 CA6NM (17-4PH SST) S17400 29 to 427 20 to 800
(420 SST) (316 SST)
H1075 heat-treated
S31600
S20910 S31600 S31600 S66286
77 with CoCr-A (alloy 6) 198 to 593 325 to 1100
SST(1) chrome coat with CoCr-A seat (660 SST)
seat and guide
S31600 with CoCr-A CA6NM N06600
79 S20910 N07718 101 to 566 150 to 1050
seat and guide chrome coat with CoCr-A seat
S31600 with CoCr-A S20910 CA6NM N06600
80 N07718 427 to 566 800 to 1050
seat and guide chrome coat(1) chrome coat with CoCr-A seat
EHD and EHT Valve with Standard Cage for Sour Service
S31600 with CoCr-A S31600 N06600
82(2) S20910 N07718 198 to 343 325 to 650
seat and guide ENC with CoCr-A seat
All Valves with Whisper Trim III Cages
S41000
F22 with CoCr-A WC9/ F22
95 (410 SST) N07718 315 to 566 600 to 1050
seat and guide nitrided with CoCr-A seat
heat treated(3)
S17400 with CoCr-A S17400 CB7CU-1 S17400
96 S17400 62 to 427 80 to 800
seat and guide H1150 H1075 with CoCr-A seat
All Valves with Whisper Trim III Cages for Sour Service
S17400 with CoCr-A S17400 S17400 S17400
97 S17400 157 to 343 250 to 650
seat and guide H1150 dbl H1150 ENC with CoCr-A seat
1. Available with 50.8 mm (2-inch) valve stem connector only.
2. Limit to 149_C (300_F) when using N04400 gasket material.
3. S41000 is limited to 538_C (1000_F). For temperatures greater than 538_C (1000_F), an S42200 stem is used.
19
Product Bulletin
51.2:EH
Table 13. Construction Materials and Temperature Capabilities for Parts Other than Body and Trim
(NPS 1-1/2 x 1 through 6 Globe and NPS 3 through 8 Angle Valves)
PART TEMPERATURE CAPABILITIES
MATERIAL
Degrees Celsius Degrees Fahrenheit
S31600 (316 stainless steel) 198 to 427 325 to 800
Valve plug S31600 (chromium coating) 427 to 593 800 to 1100
stem S20910 (1) 198 to 593 325 to 1100
S20910 (chromium coating) 427 to 593 800 to 1100
254 to 427 (to 482 for 425 to 800 (to 900 for
Graphite (FMS 17F27)
EHD/EHAD nonoxidizing service) nonoxidizing service)
piston ring 254 to 537 (to 593 for 425 to 1000 (to 1100 for
Graphite (FMS 17F39)
nonoxidizing service) nonoxidizing service)
EHT/EHAT seal ring N10276 with glass and moly-filled PTFE 73 to 232 100 to 450
EHT/EHAT seal ring backup ring Same as base material of valve plug See table 11 See table 11
Backup ring S41600 (416 SST) 29 to 427 20 to 800
S30200 (302 SST)
Retaining ring 254 to 593 425 to 1100
Spring- N07750(1)
loaded EHT
valve plug seal Seal ring PTFE with N10276 Spring 73 to 232(7) 100 to 450(7)
Anti-extrusion
PEEK (PolyEtherEtherKetone) - - -(8) - - -(8)
ring
Silver-plated N04400 254 to 593 425 to 1100
Tin-plated N04400(1) 29 to 149 20 to 300
Cage gasket
254 to 427 (to 593 for 425 to 800 (to 1100 for
S31600/Graphite(1)
O-ring Nitrile(5) 29 to 107 20 to 225

seat ring Ethylene-propylene(6) 40 to 232 40 to 450
Seat ring
gasket(1) Fluorocarbon (not for water or steam service)(5) 23 to 204 10 to 400
gasket
Flat sheet seat 254 to 427 (to 593 for 425 to 800 (to 1100 for
Graphite/stainless steel laminate
ring gasket nonoxidizing service) nonoxidizing service)
29 to 427 (WCC, WC9) 20 to 800 (WCC, WC9)
Studs Steel SA193-B7 (all body materials) -46 to 343 (LCC) -50 to 650 (LCC)
Nuts Steel SA194-2H (all body materials) 48 to 232 (CF8M [316 and 55 to 450 (CF8M [316 and
316H]) 316H])
Studs Steel SA193-B7 (WC9 body mat’l)
29 to 537 20 to 1000
Nuts Steel SA194-7 (WC9 body mat’l)
Studs Steel SA193-B16 (WC9 and C12A body mat’ls)
29 to 510 20 to 950
Nuts Steel SA194-7 (WC9 and C12A body mat’ls)
Studs 304 stainless steel SA320-B8 (CF8M [316, 316H body mat’ls])
198 to 38 325 to 100
Body-to- Nuts 304 stainless steel SA194-8 (CF8M [316, 316H body mat’ls])
bonnet Studs 316 SST SA193-B8M(3) (CF8M [316, 316H body mat’l])
bolting(2) 198 to 537 325 to 1000
Nuts 316 SST SA194-8M (CF8M [316, 316H body mat’l])
Studs 316 SST SA193-B8M chrome coat(4) (CF8M [316, 316H body mat’ls])
198 to 593 325 to 1100
Nuts 316 SST SA194-8M (CF8M [316, 316H body mat’ls])
Studs SST SA453-660 Class A (CF8M [316, 316H body mat’ls])
29 to 537 20 to 1000
Nuts Steel SA194-7 (CF8M [316, 316H body mat’ls])
Studs N07718 SST (SB037) 29 to 566 (WC9) 20 to 1050 (WC9)
Nuts Steel SA1947 29 to 593 (C12A) 20 to 1100 (C12A)
Studs Steel SA193-B7M for sour service(1) (CF8M [316 body mat’l])
46 to 232 50 to 450
Nuts Steel SA194-2HM for sour service(1) (CF8M [316 body mat’l])
PTFE V-ring 40 to 232 40 to 450
Graphite ribbon/filament (oxidizing service to 700_F) 254 to 537 425 to 1000
Graphite ribbon (high-temperature oxidizing service) 371 to 593 700 to 1100
Packing
HIGH-SEAL packing system (see Fisher Bulletin 59.1:061,
ENVIRO-SEAL and HIGH-SEAL Packing Systems for Sliding-Stem See bulletin 59.1:061 See bulletin 59.1:061
Valves, for further information)
Packing follower, spring, or
S31600 254 to 593 425 to 1100
lantern ring
Packing box ring S31600 254 to 593 425 to 1100
Packing Steel 29 to 427 20 to 800
flange, studs,
or nuts S31600 29 to 593 20 to 1100
1. Complies with NACE MR0175-2002.
2. Valve body materials with which these bolting materials may be used are shown in parentheses.
3. Class 1 (annealed).
4. Class 2 (strain hardened).
5. For use with all O-ring seat ring constructions without Cavitrol III trim.
6. For use with all O-ring seat ring constructions with Cavitrol III trim.
7. If used with PEEK anti-extrusion rings, PTFE/carbon seal ring may be used up to 316_C (600_F) for non-oxidizing service or up to 260_C (500_F) for oxidizing service.
8. These materials are not limiting factors.
20
Product Bulletin
51.2:EH
(NPS 8 through 14 Fisher EHD and EHT)
PART MATERIAL TEMPERATURE CAPABILITIES
_C _F
Silver-plated N04400 254 to 593 425 to 1100
Cage gasket 254 to 427 (to 593 for 425 to 800 (to 1100 for
S31600/Graphite(1)
Standard gasket Metal seat ring gasket Graphite filled spiral wound N06600 254 to 593 425 to 1100
construction
Nitrile 29 to 107 20 to 225
O-ring seat ring
Ethylene-propylene 40 to 232 40 to 450
gasket
Fluorocarbon 23 to 204 10 to 400
Tin-plated N04400 29 to 149 20 to 300
Cage gasket 254 to 427 (to 593 for 425 to 800 (to 1100 for
Sour service gasket S31600/Graphite(1)
construction
O-ring seat ring Nitrile 29 to 107 20 to 225
gasket Fluorocarbon 23 to 149 10 to 300
46 to 427 50 to 800
Graphite (FMS 17F27) (to 482 for (to 900 for
nonoxidizing service nonoxidizing service)
EHD piston ring
46 to 537 50 to 1000
Graphite (FMS 17F39) (to 593 for (to 1100 for
EHT seal ring R30003 (with glass and moly-filled PTFE) 73 to 232 100 to 450
EHT seal ring retaining ring S30200 (302 stainless steel) 254 to 593 425 to 1100
Backup ring S41600 (416 SST) 29 to 427 20 to 800
Spring-loaded EHT Retaining ring S30200 (302 SST) 254 to 593 425 to 1100
valve plug seal Seal ring PTFE with N10276 Spring 73 to 232(3) 100 to 450(3)
Anti-extrusion rings PEEK (PolyEtherEtherKetone) 73 to 316 100 to 600
PTFE V-ring 46 to 232 50 to 450
PTFE/composition 73 to 232 100 to 450
18 to 371 (to 537 for 0 to 700 (to 1000 for
Graphite ribbon filament
Packing
Graphite Ribbon
371 to 649 700 to 1200
(high temperature oxidizing service)
HIGH-SEAL (see Bulletin 59.1:061, HIGH-SEAL Packing Systems for Sliding-Stem Valves for
information)
Packing follower, spring, or lantern ring S31600 (316 stainless steel) 254 to 593 425 to 1100
S17400 101 to 427 150 to 800
Packing box ring
S31600 254 to 593 425 to 1100
-continued-
21
Product Bulletin
51.2:EH
(NPS 8 through 14 Fisher EHD and EHT) (continued)
PART MATERIAL TEMPERATURE CAPABILITIES
_C _F
29 to 427 20 to 800
Studs Steel SA 193-B7
(steel bodies) (steel bodies)
All body materials
48 to 232 55 to 450
Nuts Steel SA 194-2H
(SST bodies) (SST bodies)
Studs Steel SA 193-B7 WC9 and C5
29 to 537 20 to 1000
Nuts Steel SA 194-7 body materials
Studs Steel SA 193-B16 WC9 and C5
29 to 593 20 to 1100
Nuts Steel SA 194-7 body materials
304 Stainless steel
Studs
SA320-B8 CF8M (316 SST)
198 to 38 325 to 100
316 stainless steel body materials
Nuts
SA194-8
316 stainless steel
Studs
SA193-B8M(2) CF8M and CF8M
198 to 38 325 to 100
Body-to-bonnet 316 stainless steel (316H) body materials
Nuts
bolting(1) SA194-8M
316 stainless steel
Studs
SA194-B8M
CF8M body materials 198 to 427 325 to 800
316 stainless steel
Nuts
SA194-B8
316 stainless steel
Studs SA194-B8M chrome
coat(2) CF8M body materials 427 to 649 800 to 1200
316 stainless steel
Nuts
SA194-B8
Studs Steel SA 193-B7M For sour service 48 to 232 55 to 450
Nuts Steel SA 194-2HM CF8M body material (SST bodies) (SST bodies)
Stainless Steel SA453-660
Studs CF8M
Class A 29 to 537 20 to 1000
body materials
Nuts Steel SA 194-7
1. Valve body materials with which these bolting materials may be used are shown in parentheses.
2. Class 1 (annealed).
3. If used with PEEK anti-extrusion rings, PTFE/carbon seal ring may be used up to 316_C (600_F) for non-oxidizing service or up to 260_C (500_F) for oxidizing service.
Table 15. Valve Plug Travel(1) (NPS 8 through 14 Valves)

EHD, EHT
CAGE Valve Size, NPS
PRESSURE RATING
STYLE 8, 10 12, 14
mm Inches mm Inches
CL1500 76 3 102 4
Linear
CL2500 64 2.5 76 3
CL1500 76 3 102 4
Equal Percentage(1)
CL2500 64 2.5 76 3
CL1500 89 3.5 114 4.5
Modified Equal Percentage(1)
CL2500 76 3 89 3.5
CL1500 178 7 184 7.25
Whisper Trim III Cage
CL2500 146 5.75 178 7
1. Valves using an equal percentage cage may be travelled an additional 13 mm (0.05 inch) if desired to obtain additional capacity; flow characteristic becomes modified equal
percentage.
22
Product Bulletin
51.2:EH
Table 16. Flowing Pressure Drop Limits for NPS 6 CL2500 Fisher EHD/EHT and NPS 8 CL1500 or 2500 EHAD/EHAT Valves
(w/o Cavitrol III or Whisper Trim III)
MAXIMUM FLOWING PRESSURE DROP
VALVE
FLOW Bar PSI
PRESSURE STEM SIZE, mm (INCHES)
MEDIA Flowing Flowing up with Flowing Flowing up with
RATING
Down Diverter Cone Down Diverter Cone
19.1 mm (3/4 inch) 69 --- 1000 ---
All except boiler 50.8 mm (1-inch) 69 --- 1000 ---
feedwater 31.7 mm (1-1/4 inch) 138 --- 2000 ---
CL1500
50.8 x 31.7 mm(1) (2 x 1-1/4 inch(1)) 207 259 3000 3750
31.7 mm (1-1/4 inch) 69 --- 1000 ---
Boiler feedwater
50.8 x 31.7 mm(1) (2 x 1-1/4 inch(1)) 138 259 2000 3750
19.1 mm (3/4 inch) 69 --- 1000 ---
All except boiler
50.8 mm (1-inch) 69 --- 1000 ---
CL2500 feedwater
31.7 mm (1-1/4 inch) 138 431 2000 6250
Boiler feedwater 31.7 mm (1-1/4 inch) 69 431 1000 6250
1. 31.7 mm (1-1/4 inch) S20910 stem with 50.8 mm (2-inch) plug to stem connection.
49
63
BOTH GASKET CONSTRUCTIONS BOTH GASKET CONSTRUCTIONS BOTH GASKET CONSTRUCTIONS

5
O-RING CONSTRUCTION ONLY O-RING CONSTRUCTION ONLY BOTH GASKET CONSTRUCTIONS

(SOUR SERVICE)
NOTES: 1
1 FOR RECOMMENDED SERVICE APPLICATIONS, SEE TABLE 16. 3 CF8M (316 SST) VALVE BODIES ARE AVAILABLE FOR USE WITH
2 O-RING CONSTRUCTION LIMITED TO 232qC (450qF), LAMINATED TRIM 60 UP TO 232qC (450qF).
GRAPHITE CONSTRUCTION LIMITED TO 427qC (800qF) FOR OXIDIZING 4 CF8M VALVE BODIES ARE AVAILABLE FOR USE WITH TRIM 61
SERVICE AND 593qC (1100qF) FOR NON-OXIDIZING SERVICE. UP TO 232qC (450qF).
5 TRIM 49 AND 63 ARE ONLY GOOD DOWN TO 29qC (20qF).
Figure 25. Pressure/Temperature Limits for Trim Material Combinations

(NPS 1-1/2 x 1 through 6 Globe and NPS 3 through 8 Angle Valves) (also see table 16)
23
Product Bulletin
51.2:EH
FLUID TEMPERATURE, _C
TYPICAL FOR
ALL GRAPHS
CL2500
PRESSURE DROP, BAR

PRESSURE DROP, PSI
CL1500
FLUID TEMPERATURE, _F
WCC STEEL VALVES C12A VALVES
FLUID TEMPERATURE, _C PRESSURE DROP, BAR FLUID TEMPERATURE, _C
PRESSURE DROP, BAR

PRESSURE DROP, PSI
PRESSURE DROP, PSI
FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F
WC9 CHROME-MOLY STEEL VALVES CF8M (316 OR 316H ABOVE 537_C [1000_F])
STAINLESS STEEL VALVES
NOTES:
1. DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE PRESSURE RATING OF THE VALVE MATERIAL AND VALVE SIZE USED.
REFER TO FIGURE 10 FOR PRESSURE/TEMPERATURE LIMITS OF THE TRIM USED. INTERMEDIATE CLASS PRESSURE/TEMPERATURE RATINGS ARE
FOUND IN SEPARATE BULLETIN, INCREASED PRESSURE/TEMPERATURE RATINGS FOR EH SERIES AND EW SERIES STEEL VALVE BODIES.
B1959-1
Figure 26. Pressure/Temperature Limits for CL1500 and 2500 Valves (NPS 8 through 14 Valves)
24
Product Bulletin
51.2:EH
Table 17. Flowing Pressure Drops Limits for Fisher EHD and EHT Valves (Without Cavitrol III or Whisper Trim III) (NPS 8 to 14 Valves)
VALVE STEM CONNECTOR SIZE MAXIMUM FLOWING PRESSURE DROP(1) BAR (PSID)
FLOW MEDIA
mm (inch) Flowing Down Flowing Up with Diverter Cone
All except boiler feedwater 50.8 mm (2-inch) 138 (2000) 259 (3750)
Boiler feedwater 50.8 mm (2-Inch) 69 (1000) 259 (3750)
1. Do not exceed figure 27 material combination pressure drop limits.
FLUID TEMPERATURE, _C FLUID TEMPERATURE, _C FLUID TEMPERATURE, _C
PRESSURE DROP, BAR, DIFFERENTIAL


PRESSURE DROP, PSI
PRESSURE DROP, PSI
PRESSURE DROP, PSI

FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F
ALL GASKET CONSTRUCTIONS ALL GASKET CONSTRUCTIONS CL1500 VALVE WITH
FLUID TEMPERATURE, _C FLUID TEMPERATURE, _C FLUID TEMPERATURE, _C

PRESSURE DROP, PSI
PRESSURE DROP, PSI

PRESSURE DROP, PSI
FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F
ALL GASKET CONSTRUCTIONS ALL GASKET CONSTRUCTIONS CL2500 VALVE WITH

FLUID TEMPERATURE, _C FLUID TEMPERATURE, _C
PRESSURE DROP, PSI

PRESSURE DROP, PSI
NOTES:
1. FOR RECOMMENDED SERVICE APPLICATIONS,
SEE TABLE 17.
FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F

C0616-1 / IL CL1500 VALVE WITH CL2500 VALVE WITH
0-RING GASKET CONSTRUCTION 0-RING GASKET CONSTRUCTION
Figure 27. Pressure/Temperature Limits for Trim Material Combinations on CL1500 and 2500 Valves
(NPS 8 to 14 Valves) (also see table 17)
25
Product Bulletin
51.2:EH
Table 18. Additional Globe Valve Specifications (NPS 1-1/2 x 1 through 6 Globe Valves)
VALVE PRESS- PORT VALVE PLUG
VALVE DESIGN VALVE STEM DIAMETER
SIZE, URE FLOW CHARACTERISTIC DIAMETER TRAVEL
AND PLUG STYLE
NPS RATING mm Inches mm Inches mm Inches
6.4 0.25 19 0.75 12.7 1/2
EHS w/Micro-Flute 9.5 0.375 19 0.75 12.7 1/2
12.7 0.5 19 0.75 12.7 1/2
Equal percentage
6.4 0.25 19 0.75 12.7 1/2
EHS w/Micro-Form 12.7 0.5 19 0.75 12.7, 19.1 1/2, 3/4
1-1/2 x 1, 19.1 0.75 19 0.75 12.7, 19.1 1/2, 3/4
CL2500
2x1
12.7 0.5 22 0.875 12.7, 19.1 1/2, 3/4
EHS w/Micro-Form
19.1 0.75 22 0.875 12.7, 19.1 1/2, 3/4
Modified equal percentage
9.5 0.375 22 0.75 12.7 1/2
EHS w/Micro-Flute
12.7 0.5 22 0.75 12.7 1/2
Linear (Cavitrol III, 2-stage) EHS 15.9 0.625 32 1.25 12.7, 19.1 1/2, 3/4
EHS w/Micro-Form 25.4 1 22 0.875 12.7, 19.1, 25.4 1/2, 3/4, 1
Equal percentage
EHS, EHD, EHT 38.1 1.5 22 0.875 12.7, 19.1(1), 25.4(1) 1/2, 3/4(1), 1(1)
Linear (cage style: Whisper
EHS, EHD, EHT 38.1 1.5 38 1.5 12.7, 19.1(1), 25.4(1) 1/2, 3/4(1), 1(1)
Trim III, level A1)
3x2 CL2500 Linear EHS, EHD, EHT 38.1 1.5 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
EHS w/Micro-Form 25.4 1 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
EHS, EHD, EHT 38.1 1.5 29 1.125 12.7, 19.1(1), 25.4(1) 1/2, 3/4(1), 1(1)
Linear (Cavitrol III, 2-stage) EHT 31.8 1.25 51 2 12.7, 19.1 1/2, 3/4
Linear (Cavitrol III, 3-stage) EHS 15.9 0.625 51 2 12.7, 19.1 1/2, 3/4
Equal percentage EHS, EHD, EHT 58.7 2.3125 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
3, Linear (cage style: Whisper EHS, EHD, EHT 58.7 2.3125 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
CL2500
4x3 Trim III, level A1, B1)
Linear (Cavitrol III, 3-stage) EHT 33.3 1.3125 64 2.5 12.7, 19.1 25.4 1/2, 3/4, 1
Linear (Cavitrol III, 2-stage) EHT 47.6 1.875 64 2.5 12.7, 19.1 25.4 1/2, 3/4, 1
Equal percentage EHS, EHD, EHT 73 2.875 38 1.5 19.1, 25.4 3/4, 1
4, Linear (cage style: Whisper EHS, EHD, EHT 73 2.875 51 2 19.1, 25.4 3/4, 1
CL2500
6x4 Trim III, level A1, B1, B3)
Linear (Cavitrol III, 3-stage) EHT 58.7 2.3125 70 2.75 19.1, 25.4 3/4, 1
Linear (Cavitrol III, 2-stage) EHT 73 2.875 70 2.75 19.1, 25.4 3/4, 1
Equal percentage EHS, EHD, EHT 111.1 4.375 51 2 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Modified equal percentage EHS, EHD, EHT 111.1 4.375 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
6, Linear (cage style: Whisper
CL2500 EHS, EHD, EHT 111.1 4.375 76 3 25.4, 31.8 1, 1-1/4
8x6 Trim III, level B3, C3, D3)
Linear (cage style: Cavitrol III,
EHT 111.1 4.375 95 3.75 19.1, 25.4, 31.8 3/4, 1, 1-1/4
2- and 3-stage)
1. Available only with EHS valve body.
26
Product Bulletin
51.2:EH
Table 19. Additional Angle Valve Specifications (NPS 1 through 8 Angle Valves)
VALVE DESIGN AND VALVE STEM DIAMETER
PLUG STYLE
6.4 0.25 19 0.75 12.7 1/2
EHAS w/MicroFlute 9.5 0.375 19 0.75 12.7 1/2
12.7 0.5 19 0.75 12.7 1/2
Equal Percent
6.4 0.25 19 0.75 12.7 1/2
EHAS w/MicroForm 12.7 0.5 19 0.75 12.7, 19.1 1/2, 3/4
19.1 0.75 19 0.75 12.7, 19.1 1/2, 3/4
1&2 CL2500
EHAS w/MicroFlute 9.5 0.375 22 0.75 12.7 1/2
12.7 0.5 22 0.75 12.7 1/2
Modified Equal Percent
12.7 0.5 22 0.875 12.7, 19.1 1/2, 3/4
EHAS w/MicroForm
19.1 0.75 22 0.875 12.7, 19.1 1/2, 3/4
Linear(Cavitrol III,
EHAS 15.9 0.625 32 1.25 12.7, 19.1, 25.4 1/2, 3/4, 1
2stage)
31.8 1.25 19 0.75 12.7, 19.1, 25.4 1/2, 3/4, 1
EHAS w/Micro-Form
Equal percentage 38.1 1.5 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
EHAS, EHAD, EHAT 47.6 1.875 29 1.125 12.7, 19.1, 25.4(1) 1/2, 3/4, 1(1)
31.8 1.25 25 1 12.7, 19.1, 25.4 1/2, 3/4, 1
EHAS w/Micro-Form
Modified equal percentage 38.1 1.5 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
EHAS, EHAD, EHAT 47.6 1.875 38 1.5 12.7, 19.1, 25.4(1) 1/2, 3/4, 1(1)
CL1500
EHAS, EHAD, EHAT 47.6 1.875 38 1.5 12.7, 19.1, 25.4(1) 1/2, 3/4, 1(1)
Trim III, level A1)
Linear (cage style: Cavitrol
EHAT 44.5 1.75 51 2 12.7, 19.1 1/2, 3/4
III, 2-stage)
Linear (cage style: Cavitrol
EHAT 25.4 1 51 2 12.7, 19.1 1/2, 3/4
III, 3-stage)
3
EHAS w/MicroForm 25.4 1 22 0.875 12.7, 19.1, 25.4 1/2, 3/4, 1
Equal Percent
EHAS, EHAD, EHAT 38.1 1.5 22 0.875 12.7, 19.1, 25.4 1/2, 3/4, 1
EHAS w/MicroForm 25.4 1 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
Modified Equal Percent
EHAS, EHAD, EHAT 38.1 1.5 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
Linear EHAS, EHAD, EHAT 38.1 1.5 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
CL2500 Linear(Cavitrol III,
EHAT 31.8 1.25 51 2 12.7, 19.1 1/2, 3/4
2stage)
Linear(Cavitrol III,
EHAS 15.9 0.625 51 2 12.7, 19.1 1/2, 3/4
3stage)
Linear(cage style:
EHAS, EHAD, EHAT 38.1 1.5 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
Whisper Trim III Level A1)
-continued-
27
Product Bulletin
51.2:EH
Table 19. Additional Angle Valve Specifications (NPS 1 through 8 Angle Valves) (continued)
VALVE DESIGN AND VALVE STEM DIAMETER
PLUG STYLE
Equal percentage EHAS, EHAD, EHAT 73 2.875 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
Linear (cage style: Whisper EHAS, EHAD, EHAT 73 2.875 51 2 12.7, 19.1, 25.4 1/2, 3/4, 1
Trim III, level A1, B1)
CL1500
EHAT 47.6 1.875 64 2.5 12.7, 19.1, 25.4 1/2, 3/4, 1
3-stage)
4 EHAT 64 2.5 64 2.5 12.7, 19.1, 25.4 1/2, 3/4, 1
2-stage)
Equal Percent EHAS, EHAD, EHAT 58.7 2.3125 29 1.125 12.7, 19.1, 25.4 1/2, 3/4, 1
Modified Equal Percent EHAS, EHAD, EHAT 58.7 2.3125 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
Linear(Cavitrol III, 2stage) EHAT 33.3 1.3125 64 2.5 12.7, 19.1, 25.4 1/2, 3/4, 1
CL2500
Linear(Cavitrol III, 3stage) EHAT 47.6 1.875 64 2.5 12.7, 19.1, 25.4 1/2, 3/4, 1
Linear(cage style: Whisper
EHAS, EHAD, EHAT 58.7 2.3125 38 1.5 12.7, 19.1, 25.4 1/2, 3/4, 1
Trim III Level A1)
Equal percentage EHAS, EHAD, EHAT 92.1 3.625 38 1.5 19.1, 25.4 3/4, 1
Linear (cage style: Whisper EHAS, EHAD, EHAT 92.1 3.625 51 2 19.1, 25.4 3/4, 1
Trim III, level A1, B3, C3)
CL1500 EHAS, EHAD, EHAT 73 2.875 51 2 19.1, 25.4 3/4, 1
Trim III, level D3)
6
EHAT 73 2.875 76 3 19.1, 25.4 3/4, 1
3-stage)
EHAT 87.3 3.4375 76 3 19.1, 25.4 3/4, 1
2-stage)
Modified Equal Percent EHAD 92.1 3.625 51 2 31.8 1-1/4
CL2500
Linear(Cavitrol III, 3stage) EHAD 73 2.875 102 4 31.8 1-1/4
Equal percentage EHAS, EHAD, EHAT 136.5 5.375 64 2.5 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Modified equal percentage EHAS, EHAD, EHAT 136.5 5.375 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
EHAS, EHAD, EHAT 136.5 5.375 76 3 25.4, 31.8 1, 1-1/4
Trim III, level A1, B3, C3)
8 CL1500 EHAS, EHAD, EHAT 111.1 4.375 76 3 19.1, 25.4, 31.8 3/4, 1, 1-1/4
Trim III, level D3)
EHAT 115.9 4.5625 102 4 19.1, 25.4, 31.8 3/4, 1, 1-1/4
3-stage)
EHAT 133.4 5.25 102 4 19.1, 25.4, 31.8 3/4, 1, 1-1/4
2-stage)
1. Available only with EHAS valve body.
Table 20. Globe Valve Yoke Boss and Valve Stem Diameter Combinations(1) (NPS 1-1/2 x 1 through 6 Globe Valves)
STANDARD DIAMETERS OPTIONAL DIAMETERS
VALVE SIZE, NPS mm Inches mm Inches
Stem Yoke Boss Stem Yoke Boss Stem Yoke Boss Stem Yoke Boss
1-1/2 x 1, 2 x 1 12.7 71 1/2 2-13/16 19.1 90 3/4 3-9/16
12.7 71 1/2 2-13/16
3x2 25.4 127 1 5
19.1 90 3/4 3-9/16
12.7 71 1/2 2-13/16
3, 4 x 3 19.1 90 3/4 3-9/16
25.4 127 1 5
4, 6 x 4 19.1 90 3/4 3-9/16 25.4 127 1 5
25.4 127 1 5
6, 8 x 6 19.1 90 3/4 3-9/16
31.8 127 1-1/4 5H
1. See table 18 for valve stem diameters available for specific construction.
28
Product Bulletin
51.2:EH
Table 21. Angle Valve Yoke Boss and Valve Stem Diameter Combinations(1) (NPS 3 through 8 Angle Valves)
ANGLE STANDARD DIAMETERS OPTIONAL DIAMETERS
VALVE SIZE, mm Inches mm Inches
NPS Stem Yoke Boss Stem Yoke Boss Stem Yoke Boss Stem Yoke Boss
1&2 12.7 71 1/2 2.81 19.1 90 3/4 3-9/16
19.1 90 3/4 3-9/16
3 12.7 71 1/2 2-13/16
25.4 127 1 5
19.1 90 3/4 39/16
12.7 71 1/2 213/16
25.4 127 1 5
4
12.7 71 1/2 2-13/16
19.1 90 3/4 3-9/16
25.4 127 1 5
19.1 90 3/4 3-9/16 25.4 127 1 5
6
31.8 127 11/4 5
8 25.4 127 1 5 19.1 90 3/4 3-9/16
1. See table 19 for valve stem diameters available for specific construction.
Table 22. Approximate Weights (Valve and Bonnet Assemblies) (NPS 1-1/2 x 1 through 6 Globe and
NPS 3 through 8 Angle Valves)
GLOBE VALVES ANGLE VALVES
CL2500 CL1500 CL2500
VALVE SIZE,
Kilograms Pounds Kilograms Pounds Kilograms Pounds
NPS
SWE and SWE and SWE and SWE and SWE and SWE and
Flg Flg Flg Flg Flg Flg
BWE BWE BWE BWE BWE BWE
1 --- --- --- --- --- --- --- --- 73.1 53.5 161 118
1-1/2 x 1 --- 46 --- 101 --- --- --- --- --- --- --- ---
2 --- --- --- --- --- --- --- --- 98 66.2 216 146
2x1 78 47 173 104 --- --- --- --- --- --- --- ---
3x2 161 94 355 207 --- --- --- --- --- --- --- ---
3 223 163 492 359 123 78 272 173 181 99.3 399 219
4x3 265 162 585 357 --- --- --- --- --- --- --- ---
4 338 243 745 536 181 117 399 258 --- 203.2 --- 448
6x4 526 257 1160 567 --- --- --- --- --- --- --- ---
6 785 544 1731 1199 357 202 788 445 --- 496.2 --- 1094
8x6 955 558 2106 1231 --- --- --- --- --- --- --- ---
8 --- --- --- --- 648 405 1428 893 --- --- --- ---
Table 23. Approximate Weights (Valve Assembly and Bonnet) (NPS 8 through 14 Valves)
WEIGHTS
VALVE CL1500 CL2500
SIZE,
BWE FLG BWE FLG
NPS
Kilograms Pounds Kilograms Pounds Kilograms Pounds Kilograms Pounds
8 1400 3100 1700 3700 1900 4100 2200 4700
10 1500 3300 1900 4100 2000 4400 --- ---
12 3400 7300 3900 8600 3400 7600 --- ---
14 3400 7300 --- --- 3400 7600 --- ---
29
Product Bulletin
51.2:EH
Table 24. NPS 1-1/2 x 1 through 6 Globe Valve Dimensions with Standard Bonnet
A(1)
VALVE SIZE NPS CL2500
BWE SWE RF RTJ
mm
1-1/2 x 1 318 318 337 340
2x1 318 318 349 353
3x2 400 --- 435 442
3 498 --- 498 505
4x3 498 --- 518 527
4 575 --- 575 584
6x4 575 --- 660 673
6 819 --- 819 832
8x6 819 --- 857 873
Inches
1-1/2 x 1 12.50 12.50 13.25 13.38
2x1 12.50 12.50 13.75 13.88
3x2 15.75 --- 17.12 17.38
3 19.62 --- 19.62 19.88
4x3 19.62 --- 20.38 20.75
4 22.62 --- 22.62 23.00
6x4 22.62 --- 26.00 26.50
6 32.25 --- 32.25 32.75
8x6 32.25 --- 33.75 34.38
1. RF—raised-face flanges; RTJ—ring-type joint flanges; BWE—buttwelding ends; SWE—socketweld ends.
NOTE:
FOR DIMENSIONS OF VALVES WITH DIN
(OR OTHER) END CONNECTIONS,
CONSULT YOUR EMERSON PROCESS
MANAGEMENT SALES OFFICE.
MATCH LINE FOR MATCH LINE FOR

ACTUATOR ACTUATOR
MATCH LINE FOR 585CLS

ACTUATORS AND 657 AND 667
SIZE 100 ACTUATORS
MATCH LINE
FOR ALL
OTHER
ACTUATORS 25.4
(1.00)
mm
(INCHES)
FLANGED VALVE WITH 71 OR 90 mm BUTTWELDING END VALVE WITH 71 OR 90 127 mm (5-INCH) DIAMETER YOKE BOSS
(2-13/16 OR 3-9/16 INCH) DIAMETER YOKE mm (2-13/16 OR 3-9/16 INCH) FOR USE WITH FLANGED OR
BOSS DIAMETER YOKE BOSS BUTTWELDING VALVE
A2719-4 / IL
Figure 28. NPS 1-1/2 x 1 through 6 Globe Valve Dimensions with Standard Bonnet (also see tables 24, 25, and 26)
30
Product Bulletin
51.2:EH
B(1)
VALVE SIZE NPS CL2500
BWE SWE RF RTJ
mm
1-1/2 x 1 159 159 168 170
2x1 159 159 175 176
3x2 200 --- 217 221
3 249 --- 249 253
4x3 249 --- 259 264
4 273 --- 273 278
6x4 273 --- 325 331
6 397 --- 397 403
8x6 397 --- 416 424
Inches
1-1/2 x 1 6.25 6.25 6.62 6.69
2x1 6.25 6.25 6.88 6.94
3x2 7.88 --- 8.56 8.69
3 9.81 --- 9.81 9.94
4x3 9.81 --- 10.19 10.38
4 10.75 --- 10.75 10.94
6x4 10.75 --- 12.81 13.06
6 15.62 --- 15.62 15.88
8x6 15.62 --- 16.38 16.69
1. RF—raised-face flanges; RTJ—ring-type joint flanges; BWE—buttwelding ends; SWE—socketweld ends.
G D
VALVE CL2500
SIZE
CL2500 Yoke Boss Diameters, mm (Inches)
NPS
71 (2-13/16) 90 (3-9/16) 127 (5)
mm
1-1/2 x 1 78 249 256 ---
2x1 78 249 256 ---
3x2 108 303 310 343
3 145 335 335 371
4x3 145 335 335 371
4 168 --- 348 406
6x4 168 --- 348 406
6 229 --- 408 445
8x6 229 --- 408 445
Inches
1-1/2 x 1 3.06 9.81 10.06 ---
2x1 3.06 9.81 10.06 ---
3x2 4.35 11.94 12.19 13.50
3 5.69 13.19 13.19 14.62
4x3 5.69 13.19 13.19 14.62
4 6.62 --- 13.69 16.00
6x4 6.62 --- 13.69 16.00
6 9.00 --- 16.06 17.50
8x6 9.00 --- 16.06 17.50
31
Product Bulletin
51.2:EH
Table 27. Dimension D for Style 1 Extension Bonnet (A, B,

MATCH LINE FOR 585CLS
and G Dimensions Listed in Figure 28 Do Not Change ACTUATORS
When Extension Bonnet is Used MATCH LINE FOR ALL
OTHER ACTUATORS
GLOBE D
VALVE PRESSURE Yoke Boss Diameter, mm (Inches)
SIZE, RATING
NPS 71 (2-13/16) 90 (3-9/16) 127 (5) 25.4
mm (1.00)
1-1/2 x 1
CL2500 391 406 ---
and 2 x 1 127 mm (5-INCH) DIAMETER YOKE BOSS
3x2 CL2500 427 443 502 FOR STYLE 1 EXTENSION BONNET
Inches
1-1/2 x 1
CL2500 15.38 16.00 ---
and 2 x 1
3x2 CL2500 16.81 17.44 19.75 MATCH LINE
FOR ACTUATOR
Installation
The valve must be installed so flow through the

valve matches the flow direction arrow on the valve
body. Consideration should be given to installing an
upstream strainer, especially if the valve uses a
multi-orifice Whisper Trim III or Cavitrol III cage.
For NPS 8 and larger valves, the recommended

installation position is with the valve in a horizontal
pipeline and the actuator vertical above the valve.
Other orientations may result in shortened trim life
FLANGED VALVE WITH STYLE 1
and difficulty with field maintenance. EXTENSION BONNET HAVING 71 OR 90 mm
(2-13/16 OR 3-9/16 INCH) DIAMETER
YOKE BOSS
Overall dimensions are shown in figures 28, 29, 30, 18A5906-C
A3002-2 / IL
31, and 32. Face-to-face dimensions are in
compliance with ANSI/ISA-S75 for valves smaller
than NPS 8. For NPS 8 and larger valves, Figure 29. Dimension D for Style 1 Extension Bonnet (A, B,
face-to-face dimensions are longer than industry and G Dimensions Listed in Figure 28 Do Not Change When
standards for valves of this size and rating. Actual Extension Bonnet is Used) (also see table 27)
end connection dimensions conform to ASME
B16.25 for buttwelding ends and to ASME B16.5 for
flanged ends.
32
Product Bulletin
51.2:EH
Table 28. NPS 3 through 8 Angle Valve CL1500 Dimensions with Standard Bonnet and Style 1 Extension Bonnet
A, mm D
VALVE Std. Bonnet Ext. Bonnet
SIZE, NPS Stem Diameter, mm Stem Diameter, mm
BWE SWE RF RTJ 1/2 3/4 1, 1-1/4 1/2 3/4 1
3 235 --- 235 237 259 265 329 427 443 502
4 273 --- 273 275 287 278 338 --- --- ---
6 353 --- 353 356 --- 302 380 --- --- ---
8 416 --- 416 421 --- 367 403 --- --- ---
Inches
3 9.25 --- 9.25 9.31 10.19 10.44 12.94 16.81 17.44 19.75
4 10.75 --- 10.75 10.81 11.31 10.94 13.31 --- --- ---
6 13.88 --- 13.88 14.00 --- 11.88 14.56 --- --- ---
8 16.38 --- 16.38 16.56 --- 14.44 15.88 --- --- ---
Table 29. NPS 1 through 6 Angle Valve CL2500 Dimensions with Standard Bonnet
A, mm D
VALVE PRESSURE
SIZE, NPS RATING Std. Bonnet
BWE SWE RF RTJ BWE SWE RF RTJ
1 CL2500 153.9 153.9 153.9 153.9 256.5 392.2 408.1 408.1
2 CL2500 225.6 225.6 225.6 227.1 408.1 408.1 250.0 256.5
3 CL2500 289.1 292.1 308.9 308.9
4 CL2500 336.6 334.8
6 CL3230(1) 374.7 451.7
Inches
1 CL2500 6.06 6.06 6.06 6.06 10.097 15.440 16.065 16.065
2 CL2500 8.88 8.88 8.88 8.94 16.065 16.065 9.844 10.097
3 CL2500 11.38 11.5 12.162 12.162
4 CL2500 13.25 13.182
6 CL3230(1) 14.75 17.782
1. NPS 6 is an intermediate CL3230.
MATCH LINE FOR

1/2 and 3/4 STEM ACTUATOR
MATCH LINE FOR 585CLS ACTUATORS

AND 657, 667 SIZE 100 ACTUATORS
1 and 1-1/4 STEM
MATCH LINE FOR ALL

OTHER ACTUATORS
10B2281-A
A4172 / IL
Figure 30. NPS 3 through 8 Angle Valve CL1500 Dimensions with Standard Bonnet and Style 1 Extension Bonnet
(also see table 28)
33
Product Bulletin
51.2:EH
Table 30. Dimensions (NPS 8 through 14 Fisher EHD and EHT Valves)
VALVE A(1,2)
SIZE, CL900 CL1500 CL2500
NPS RF RTJ BWE RF RTJ BWE RF RTJ
mm
8 1137 1140 1194 1194 1203 1295 1295 1311
10 1168 1172 1245 1245 1254 1346 --- ---
12 1715 1718 1803 1803 1819 1778 --- ---
14 1727 1739 1829 --- --- 1803 --- ---
Inches
8 44.75 44.88 47.00 47.00 47.38 51.00 51.00 51.62
10 46.00 46.13 49.00 49.00 49.38 53.00 --- ---
12 67.50 67.62 71.00 71.00 71.62 70.00 --- ---
14 68.00 68.38 72.00 --- --- 71.00 --- ---
VALVE B(1,2)
SIZE, CL900 CL1500 CL2500
NPS BWE RF RTJ BWE RF RTJ
mm
8 429 430 457 457 462 508 508 516
10 445 446 483 483 487 533 --- ---
12 794 795 838 838 846 838 --- ---
14 800 805 851 --- --- 851 --- ---
Inches
8 16.88 16.94 18.00 18.00 18.19 20.00 20.00 20.31
10 17.50 17.56 19.00 19.00 19.19 21.00 --- ---
12 31.25 31.31 33.00 33.00 33.31 33.00 --- ---
14 31.50 31.69 33.50 --- --- 33.50 --- ---
1. Face-to-face dimensions for these valves are not standard dimensions due to the lack of industry standards for valves of this size and rating.
2. BWE—buttwelding ends; RF—raised-face flanges; RTJ—ring-type joint flanges.
Table 31. Dimensions (NPS 8 through 14 Fisher EHD

and EHT Valves)
MATCH LINE FOR
VALVE D G ACTUATOR
SIZE, CL900 and CL900 and
CL2500 CL2500
NPS 1500 1500
mm D
8, 10 684 665 363 370
12, 14 702 724 452 437
Inches G
MATCH LINE FOR
8, 10 26.94 26.19 14.31 14.56 ACTUATOR
12, 14 27.62 28.50 17.81 17.19 B
A
15A4693-C
FLANGED ENDS D
NOTE:
FOR DIMENSIONS OF
VALVES WITH EN (OR
OTHER) END CONNECTIONS,
CONSULT YOUR EMERSON G
PROCESS MANAGEMENT
SALES OFFICE.
B
A2888-1 / IL A
15A4691-F
BUTTWELDING ENDS
Figure 31. Dimensions (NPS 8 through 14 Fisher EHD and

EHT Valves) (also see tables 30 and 31)
34
Product Bulletin
51.2:EH
895
(35.25)
663
(26.12)
1118
(44.00)
1981 + / 3.0 mm
78.00 + / 0.12) (INCH)
A3349/IL
Figure 32. Dimensions (NPS 20 Fisher EHD Valve)
35
Product Bulletin
51.2:EH
Coefficients
Table 32. Fisher EHD, CL900 and 1500, Linear and Equal Percentage Cages
Linear - Flow Down Linear

Characteristic
Valve Maximum Flow
Port Diameter Valve Opening—Percent of Total Travel
Size, Travel Coeffi- FL(1)
NPS mm Inches mm Inches cient 10 20 30 40 50 60 70 80 90 100
Cv 105 212 332 458 578 689 788 878 954 1020 0.82
8 & 10x8 177.8 7 76 3 Kv 90.8 183 287 396 500 596 682 759 825 882 ---
XT 0.591 0.676 0.661 0.653 0.633 0.620 0.624 0.622 0.614 0.592 ---
Cv 211 390 593 804 1010 1240 1460 1660 1830 1970 0.80
12 &
254.0 10 102 4 Kv 183 337 513 695 874 1073 1263 1436 1583 1704 ---
14x12
XT 0.443 0.652 0.669 0.664 0.671 0.653 0.662 0.669 0.658 0.629 ---
Equal Percentage - Flow Down Equal Percentage

Characteristic
Cv 32.5 59.6 85.3 114 159 229 334 468 619 755 0.85
8 & 10x8 177.8 7 76 3 Kv 28.1 51.6 73.8 98.6 138 198 289 405 535 653 ---
XT 0.969 0.939 0.842 0.944 0.840 0.731 0.641 0.633 0.639 0.639 ---
Cv 81.3 143 207 286 382 557 752 1000 1290 1570 0.82
12 &
254.0 10 102 4 Kv 70.3 124 179 247 330 482 650 865 1116 1358 ---
14x12
XT 0.689 0.581 0.579 0.557 0.606 0.582 0.647 0.644 0.616 0.596 ---
1. At 100% travel.
Notes: The coefficients in this table are also appropriate for the EHT Valve.
Table 33. Fisher EHD, CL900 and 1500, Equal Percentage Cages
Modified Equal Percentage - Flow Down Modified Equal Percentage

Characteristic
Valve Maximum Flow
Cv 38.3 70.2 103 145 216 324 495 684 844 912 0.85
8 & 10x8 177.8 7 89 3.5 Kv 33.1 60.7 89.1 125 187 280 428 592 730 789 ---
XT 0.946 0.891 0.910 0.835 0.744 0.669 0.669 0.664 0.668 0.667 ---
Cv 95.9 156 229 313 487 710 988 1280 1610 1830 0.83
12 &
254.0 10 114 4.5 Kv 83.0 135 198 271 421 614 855 1107 1393 1583 ---
14x12
XT 0.579 0.607 0.561 0.618 0.577 0.617 0.576 0.620 0.610 0.611 ---
1. At 100% travel.
36
Product Bulletin
51.2:EH
Table 34. Fisher EHD, CL2500, Linear and Equal Percentage Cages
Linear - Flow Down Linear

Characteristic
Valve Maximum Flow
Cv 1.44 3.39 9.44 15.2 20.5 25.0 29.0 32.3 34.9 36.1 0.93
2&3x2 38.1 1.5 29 1.125 Kv 1.25 2.93 8.17 13.1 17.7 21.6 25.1 27.9 30.2 31.2 ---
XT 0.718 0.612 0.566 0.605 0.648 0.697 0.727 0.740 0.740 0.735 ---
Cv 2.77 13.2 31.0 47.4 59.7 68.7 75.5 80.6 83.9 85.9 0.95
3&4x3 58.7 2.3125 38 1.5 Kv 2.40 11.4 26.8 41.0 51.6 59.4 65.3 69.7 72.6 74.3 ---
XT 0.685 0.574 0.612 0.668 0.714 0.731 0.735 0.718 0.701 0.706 ---
Cv 2.99 17.4 38.1 57.8 78.8 100 119 130 136 139 0.88
4&6x4 73.0 2.875 51 2 Kv 2.59 15.1 33.0 50.0 68.2 86.5 103 112 118 120 ---
XT 0.757 0.624 0.570 0.533 0.559 0.632 0.681 0.706 0.697 0.689 ---
Cv 17.5 38.9 86.1 141 195 241 274 293 301 309 0.89
6 & 8 x 6 111.1 4.375 76 3 Kv 15.1 33.6 74.5 122 169 208 237 253 260 267 ---
XT 0.187 0.624 0.548 0.559 0.597 0.640 0.681 0.697 0.689 0.681 ---
Cv 75.1 140 212 289 366 435 495 547 590 621 0.82
8 & 10x8 136.5 5.375 64 2.5 Kv 65.0 121 183 250 317 376 428 473 510 537 ---
XT 0.772 0.833 0.840 0.779 0.741 0.733 0.729 0.715 0.704 0.688 ---
Cv 104 229 369 477 587 691 804 906 981 1030 0.81
12 &
177.8 7 76 3 Kv 90.0 198 319 413 508 598 695 784 849 891 ---
14x12
XT 0.406 0.476 0.478 0.523 0.543 0.561 0.552 0.547 0.558 0.584 ---
Equal Percentage - Flow Down Equal Percentage

Characteristic
Valve Maximum Flow
Cv 1.25 1.36 2.47 4.14 6.33 9.48 13.8 18.7 23.1 27.0 0.93
2&3x2 38.1 1.5 22 0.875 Kv 1.08 1.18 2.14 3.58 5.48 8.20 11.9 16.2 20.0 23.4 ---
XT 0.766 0.761 0.608 0.589 0.601 0.601 0.593 0.605 0.660 0.735 ---
Cv 1.73 2.77 5.34 9.70 15.6 23.3 33.7 46.2 56.8 65.3 0.92
3&4x3 58.7 2.3125 29 1.125 Kv 1.50 2.40 4.62 8.39 13.5 20.2 29.2 40.0 49.1 56.5 ---
XT 0.870 0.710 0.605 0.581 0.616 0.648 0.640 0.632 0.668 0.748 ---
Cv 2.57 6.53 10.0 12.5 17.3 25.1 33.8 42.8 59.6 81.1 0.84
4&6x4 73.0 2.875 38 1.5 Kv 2.22 5.65 8.65 10.8 15.0 21.7 29.2 37.0 51.6 70.2 ---
XT 0.783 0.585 0.589 0.597 0.566 0.533 0.518 0.526 0.526 0.537 ---
Cv 3.07 9.29 17.8 24.5 35.6 59.7 98.7 141 188 217 0.85
6 & 8 x 6 111.1 4.375 51 2 Kv 2.66 8.04 15.4 21.2 30.8 51.6 85.4 122 163 188 ---
XT 0.922 0.723 0.620 0.660 0.640 0.555 0.529 0.578 0.559 0.640 ---
Cv 19.8 34.4 50.3 69.2 96.8 139 210 307 399 484 0.82
8 & 10x8 136.5 5.375 64 2.5 Kv 17.1 29.8 43.5 59.9 83.7 120 182 266 345 419 ---
XT 0.584 0.686 0.697 0.609 0.629 0.745 0.702 0.653 0.663 0.683 ---
Cv 38.4 64.8 88.0 119 168 248 360 496 654 800 0.81
12 &
177.8 7 76 3 Kv 33.2 56.1 76.1 103 145 215 311 429 566 692 ---
14x12
XT 0.727 0.701 0.736 0.664 0.709 0.582 0.552 0.556 0.556 0.553 ---
1. At 100% travel.
37
Product Bulletin
51.2:EH
Table 35. Fisher EHD, CL2500, Equal Percentage Cages
Modified Equal Percentage - Flow Down Modified Equal Percentage

Characteristic
Valve Maximum Flow
Cv 1.24 1.82 3.91 6.86 11.1 16.9 23.3 28.1 30.4 33.2 0.94
2&3x2 38.1 1.5 29 1.125 Kv 1.07 1.57 3.38 5.93 9.60 14.6 20.2 24.3 26.3 28.7 ---
XT 0.792 0.681 0.578 0.581 0.605 0.628 0.652 0.693 0.731 0.710 ---
Cv 1.94 4.28 9.66 18.1 29.9 45.4 60.5 68.9 74.7 80.9 0.96
3&4x3 58.7 2.3125 38 1.5 Kv 1.68 3.70 8.36 15.7 25.9 39.3 52.3 59.6 64.6 70.0 ---
XT 0.805 0.640 0.593 0.624 0.668 0.672 0.677 0.753 0.779 0.710 ---
Cv 2.99 9.01 12.7 19.6 30.3 44.5 65.8 96.3 114 126 0.90
4&6x4 73.0 2.875 51 2 Kv 2.59 7.79 11.0 17.0 26.2 38.5 56.9 83.3 98.6 109 ---
XT 0.681 0.578 0.593 0.559 0.526 0.518 0.544 0.597 0.693 0.693 ---
Cv 5.82 16.2 30.6 59.8 115 185 234 254 278 293 0.88
6 & 8 x 6 111.1 4.375 76 3 Kv 5.03 14.0 26.5 51.7 99.5 160 202 220 240 253 ---
XT 0.806 0.677 0.624 0.574 0.559 0.597 0.664 0.723 0.706 0.689 ---
Cv 22.9 41.9 61.9 86.4 140 225 334 451 537 584 0.85
8 & 10x8 136.5 5.375 76 3 Kv 19.8 36.2 53.5 74.7 121 195 289 390 465 505 ---
XT 0.563 0.698 0.726 0.739 0.734 0.691 0.666 0.682 0.734 0.740 ---
Cv 42.4 73.7 104 147 223 351 523 717 899 1010 0.80
12 &
177.8 7 89 3.5 Kv 36.7 63.8 90.0 127 193 304 452 620 778 874 ---
14x12
XT 0.691 0.679 0.652 0.650 0.598 0.549 0.549 0.552 0.551 0.551 ---
1. At 100% travel.
38
Product Bulletin
51.2:EH
Table 36. Fisher EHS, CL2500, Linear and Equal Percentage Cages
Linear - Flow Up Linear

Characteristic
Valve Maximum Flow
Cv 1.40 2.77 8.42 14.3 19.3 23.9 28.0 31.4 33.4 35.2 0.90
2&3x2 38.1 1.5 29 1.125 Kv 1.21 2.40 7.28 12.4 16.7 20.7 24.2 27.2 28.9 30.4 ---
XT 0.718 0.815 0.624 0.628 0.685 0.706 0.701 0.685 0.677 0.656 ---
Cv 2.98 11.7 28.3 45.7 58.8 67.9 75.3 82.0 86.4 88.6 0.94
3&4x3 58.7 2.3125 38 1.5 Kv 2.58 10.1 24.5 39.5 50.9 58.7 65.1 70.9 74.7 76.6 ---
XT 0.706 0.664 0.697 0.710 0.731 0.731 0.727 0.710 0.689 0.681 ---
Cv 2.92 15.1 30.6 48.6 68.0 86.8 103 116 123 125 0.92
4&6x4 73.0 2.875 51 2 Kv 2.53 13.1 26.5 42.0 58.8 75.1 89.1 100 106 108 ---
XT 0.748 0.819 0.792 0.636 0.624 0.697 0.779 0.797 0.788 0.797 ---
Cv 9.11 37.3 78.2 128 180 224 254 269 278 282 0.89
6 & 8 x 6 111.1 4.375 76 3 Kv 7.88 32.3 67.6 111 156 194 220 233 240 244 ---
XT 0.620 0.656 0.589 0.574 0.601 0.648 0.689 0.718 0.714 0.714 ---
Equal Percentage - Flow Up Equal Percentage

Characteristic
Cv 1.06 1.31 2.10 3.73 6.26 9.46 13.1 17.3 22.1 26.3 0.91
2&3x2 38.1 1.5 22 0.875 Kv 0.917 1.13 1.82 3.23 5.41 8.18 11.3 15.0 19.1 22.7 ---
XT 0.970 0.757 0.731 0.689 0.652 0.624 0.624 0.648 0.693 0.723 ---
Cv 1.94 2.86 5.09 9.02 14.9 22.6 32.1 43.0 53.9 64.7 0.94
3&4x3 58.7 2.3125 29 1.125 Kv 1.68 2.47 4.40 7.80 12.9 19.5 27.8 37.2 46.6 56.0 ---
XT 0.810 0.757 0.681 0.677 0.706 0.706 0.668 0.652 0.723 0.761 ---
Cv 2.35 6.15 9.08 11.3 15.4 22.0 30.3 40.0 53.9 69.6 0.80
4&6x4 73.0 2.875 38 1.5 Kv 2.03 5.32 7.85 9.77 13.3 19.0 26.2 34.6 46.6 60.2 ---
XT 0.856 0.681 0.620 0.656 0.644 0.597 0.555 0.555 0.578 0.632 ---
Cv 4.10 9.98 17.9 24.7 35.3 57.3 93.0 133 174 210 0.79
6 & 8 x 6 111.1 4.375 51 2 Kv 3.55 8.63 15.5 21.4 30.5 49.6 80.4 115 151 182 ---
XT 0.697 0.677 0.605 0.578 0.597 0.608 0.574 0.555 0.616 0.605 ---
Modified Equal Percentage - Flow Up Modified Equal Percentage

Characteristic
Cv 1.10 1.71 3.37 6.56 11.2 16.5 21.6 26.4 30.8 33.1 0.91
2&3x2 38.1 1.5 29 1.125 Kv 0.952 1.48 2.92 5.67 9.69 14.3 18.7 22.8 26.6 28.6 ---
XT 0.898 0.748 0.689 0.640 0.636 0.656 0.693 0.723 0.727 0.677 ---
Cv 2.11 4.16 8.97 16.9 28.4 42.5 55.8 68.2 78.5 84.0 0.
3&4x3 58.7 2.3125 38 1.5 Kv 1.83 3.60 7.76 14.6 24.6 36.8 48.3 59.0 67.9 72.7 ---
XT 0.828 0.710 0.672 0.731 0.723 0.689 0.731 0.766 0.723 0.706 ---
Cv 2.75 8.60 11.8 16.6 26.8 42.3 59.8 78.9 106 116 0.88
4&6x4 73.0 2.875 51 2 Kv 2.38 7.44 10.2 14.4 23.2 36.6 51.7 68.2 91.7 100.3 ---
XT --- 0.608 0.636 0.640 0.570 0.537 0.578 0.664 0.693 0.779 ---
Cv 6.81 16.5 30.5 58.0 109 175 228 256 275 281 0.88
6 & 8 x 6 111.1 4.375 76 3 Kv 5.89 14.3 26.4 50.2 94.3 151 197 221 238 243 ---
XT 0.677 0.632 0.593 0.570 0.574 0.601 0.624 0.644 0.693 0.697 ---
1. At 100% travel.
39
Product Bulletin
51.2:EH
Table 37. Fisher EHS, CL2500, Micro-Form Valve Plug
Micro-Form - Flow Up Equal Percentage

Characteristic
Valve Maximum Flow
Cv 0.072 0.106 0.163 0.232 0.324 0.449 0.626 0.871 1.22 1.58 0.91
6.4 0.25 19 0.75 Kv 0.062 0.092 0.141 0.201 0.280 0.388 0.541 0.753 1.06 1.37 ---
XT 0.778 0.717 0.421 0.474 0.513 0.540 0.558 0.566 0.569 0.644 ---
Cv 0.220 0.360 0.532 0.746 1.04 1.50 2.15 3.06 4.15 5.37 0.92
19 0.75 Kv 0.190 0.311 0.460 0.645 0.900 1.30 1.86 2.65 3.59 4.65 ---
XT 0.893 0.803 0.748 0.636 0.633 0.637 0.644 0.642 0.661 0.718 ---
12.7 0.5
1, Cv 0.254 0.445 0.636 0.890 1.40 2.23 3.50 4.77 5.72 6.36 0.93
1-1/2 x 1, 22(2) 0.875(2) Kv 0.220 0.385 0.550 0.770 1.21 1.93 3.03 4.13 4.95 5.50 ---
&2x1 XT 0.632 0.627 0.630 0.632 0.629 0.628 0.629 0.626 0.633 0.630 ---
Cv 0.441 0.681 1.04 1.59 2.36 3.43 4.81 6.43 7.84 8.91 0.88
19 0.75 Kv 0.381 0.589 0.900 1.38 2.04 2.97 4.16 5.56 6.78 7.71 ---
XT 0.782 0.725 0.652 0.548 0.519 0.506 0.514 0.641 0.651 0.648 ---
19.1 0.75
Cv 0.550 0.721 1.24 1.85 2.78 4.43 6.70 8.45 9.27 10.3 0.84
22(2) 0.875(2) Kv 0.476 0.624 1.07 1.60 2.40 3.83 5.80 7.31 8.02 8.91 ---
XT 0.516 0.693 0.581 0.587 0.586 0.589 0.585 0.583 0.587 0.585 ---
Cv 0.653 1.19 1.89 2.89 4.50 7.08 10.9 15.9 20.0 21.5 0.95
22 0.875 Kv 0.565 1.03 1.63 2.50 3.89 6.12 9.43 13.8 17.3 18.6 ---
2& XT 0.809 0.812 0.814 0.809 0.810 0.811 0.817 0.806 0.810 0.810 ---
25.4 1
3x2 Cv 0.884 1.67 2.86 4.96 9.08 15.6 20.9 23.0 23.9 24.2 0.92
29(2) 1.125(2) Kv 0.765 1.44 2.47 4.29 7.85 13.5 18.1 19.9 20.7 20.9 ---
XT 0.696 0.700 0.698 0.700 0.696 0.700 0.697 0.745 0.714 0.700 --
1. At 100% travel.
2. Travels identified with this superscript are modified equal percentage characteristic. All other travels are equal percentage.
40
Product Bulletin
51.2:EH
Specifications
Available Configurations Temperature Capabilities specification(7) or in
See table 1. figures 24 and 25.
In addition, both steel EH and EHA valves with
Common Characteristics: EH valves are
BWE connections have increased pressure/
single-port, high-pressure, globe-style valves with temperature ratings as shown in tables 7 and 8.
metal seats, cage guiding, and push- down- to-
close valve plug action. EHA valves are angle Maximum Pressure Drops(3)
versions of EH valves Valve With Standard Cage: See figures 24, 25,
EHD/EHAD: Uses a balanced valve plug(1) with 26 and 27.
graphite valve plug piston rings; also, see tables 3 Valve With Cavitrol III Cage: 149 bar (2160 psi)
and 4. for two-stage cage and 207 bar (3000 psi) for
EHS/EHAS: Uses an unbalanced valve plug. For three-stage cage. Consult Bulletin 80.2:018,
low-flow applications, smaller valve sizes are Cavitrol III Two- and Three-Stage Trims, for more
available with specialized valve plug designs. See information
tables 3(1) and 4. Valve With Whisper Trim III Cage:
EHT/EHAT: Uses a balanced valve plug(1) with a J 0.6 'P/P1 maximum for Levels A1 and A3,
pressure-assisted PTFE valve plug seal ring; also, J 0.75 'P/P1 maximum for Levels B1 and B3,
see tables 3 and 4. J 0.85 'P/P1 maximum for Levels C1 and C3,
NPS 20 Valve Rating J 0.99 'P/P1 maximum for Levels D1 and D3
Valve with WhisperFlo Trim:
J Intermediate Standard Class 2185 (per ASME
J Levels X, Y, and Z: 0.94 nP/P1 maximum. If
B16.34) or J other ratings available per customer
specifications greater than 0.94 nP/P1, consult your Emerson
Process Management sales office
Valve Sizes
Construction Materials
J Globe Valves: Tables 3 and 5.
J Angle Valves: Tables 4 and 6 All Except NPS 20 Valve.
Body and Bonnet: J WCC steel, J LCC steel,
End Connection Styles(2) J WC9 chrome-moly steel, J C12A chrome-moly
Buttwelding Ends (BWE): See tables 5 and 6 for alloy, or J CF8M (316 SST or 316H SST for
all available ASME B16.25 schedules that are service above 538_C [1000_F])
compatible with ASME B16.34 Trim: Trim materials are listed in table 11 and 12.
pressure/temperature ratings Special materials for trim and valve body are
Flanged Ends: J CL900, J CL1500, or available. Please consult your Emerson Process
J CL2500 J ring-type joint (RTJ) or Management sales office
J raised-face (RF) flanges according to ASME Other Parts: See tables 13 and 14.
B16.5. Flanged ends for EHA valves are available Yoke Temperature Limit (NPS 8 to 20 Valves):
in CL900 and 1500 only Standard bonnet with cast iron yoke is limited to
Socketweld Ends (SWE): See tables 5 and 6 for 537_C (1000_F)
those valve sizes available with socketweld end NPS 20 Valve.
connections according to ASME B16.11 that are Valve Body and Bonnet: SA 217 Grade WC9 steel
compatible with ASME B16.34 Cage: Cast M152 SST
Valve Plug: CF8M (316 stainless steel) with alloy
Maximum Inlet Pressures and Temperatures(2,3) 6 seat and guide
Consistent with applicable CL900, 1500, or 2500 Seat Ring: CF8M with CoCr-A (alloy 6) seat or
pressure/temperature ratings (for EH valves) or N06600 with CoCr-A seat
CL900 or 1500 (for EHA valves) according to Seat Ring Bolting: N07718
ASME B16.34 unless limited by individual Valve Stem: J SA 286 Grade 660 Condition 2
temperature limits shown in the Material stainless steel or J other materials upon request
- continued -
41
Product Bulletin
51.2:EH
Specifications (continued)
NPS 20 Valve. J EHS: Normal flow up(5).
Piston Rings: Graphite J EHT: Normal flow down(8).
Cage & Seat Ring Gaskets: Silver-plated N04400 J EHAD: Normal flow down
Body/Bonnet Bolting: Steel J EHAS: Normal flow up
Packing Rings: Carbon/graphite composition, J EHAT: Normal flow down
graphite, and zinc
Packing Box Bushing: Graphite Cavitrol III Cage: Flow down
Packing Box Flange, Studs, and Nuts: S31600 Whisper Trim III cage: Flow up
(316 stainless steel) (other materials are available
on request) WhisperFlo Trim: Flow up
Springs: J G61500 (6150 steel), J S17700 (17-7
stainless steel) or J N07718 For NPS 20 Valves: J Flow up through seat ring
and out through cage openings (for standard and
Shutoff Classifications Whisper cages)
See table 10. Noise Levels
For NPS 20 valves, one-half of Class IV leakage
(0.005% of valve capacity at full travel) per See Fisher Catalog 12, section 3 for noise
ANSI/FCI 70-2 and IEC 60534-4 predictions methods
Material Temperature Capabilities(3) NPS 20 Valve Maximum Flow Coefficient

EHD/EHAD and EHS/EHAS: Up to 593_C Approximately 92,000 Cg or 2600 Cv
(1100_F) unless limited by selection of standard
trim materials (table 11 and 12 and figures 24, 25, Port Diameters
26, and 27), Cavitrol III and Whisper Trim III trim
See tables 18 and 19.
materials (table 11), or other parts (table 13).
EHT/EHAT: Up to 316_C (600_F) unless limited NPS 8 and 10x8 Valves.
by selection of standard trim materials (tables 11 CL1500: 178 mm (7 inch) port diameter
and 12 and figures 24, 25, 26, and 27), Cavitrol III CL2500: 137 mm (5.375 inch) port diameter
and Whisper Trim III trim materials (table 11), or NPS 12, 14, and 14x12 Valves.
other parts (tables 13 and 14) CL1500: 254 mm (10 inch) port diameter
CL2500: 178 mm (7 inch) port diameter
Flow Characteristic
NPS 14 Valves.
Standard Cage: J Equal percentage, J modified CL2500 Valve: 356 mm (14 inches) port diameter
equal percentage(4), or J linear (consult your Emerson Process Management
Standard Cage with Micro-Form Valve Plug: sales office for further information)
J Equal percentage or J modified equal NPS 16x12 Valves.
percentage(4). CL1500: 254 mm (10 inch) port diameter
Standard Cage with Micro-Flute Valve Plug: CL2500: 254 mm (10 inch) port diameter
J Equal percentage or J modified equal NPS 20 Valves: 355.6 mm (14 inches)
percentage(4).
Standard Cage with Micro-Flat Valve Plug Valve Plug Travel and Stem Diameters(9)
(EHAS only): J Linear
See tables 15, 18, and 19.
Cavitrol III or Whisper Trim III Cage: J Linear
Special cages: Special characterized flow 5 Inch H(10) Boss Diameter: 31.8 mm (1.25
characteristic cages are available. Please consult inches) stem diameter
your local Emerson Process Management sales 7 Inch Boss Diameter: 50.8 mm (2 inches) stem
office. diameter
NPS 20 Valves: Valve Plug Travel: 85.7 mm
Flow Direction
(9.125 inches) plus or minus 1.6 mm (0.0625
Standard Cage. inch)
J EHD: Normal flow down(8). Valve Stem Diameter: 50.4 mm (2 inches)
- continued -
42
Product Bulletin
51.2:EH
Specifications (continued)
Bonnet Style J driver for removing and installing of seat ring
J Standard bonnet (figures 4 and 5) for all valve retainer, J Class V shutoff for EHT above 232_C
sizes, standard bonnet with cast iron yoke is (450_F) using PEEK anti-extrusion rings, J Class
limited to 537_C (1000_F) V shutoff for EHD 4-3/8 inch port and smaller for
J Optional Style 1 extension bonnet for NPS 1 up to 593_C (1100_F) using C-seal trim and EHD
and 2 globe valves, see figure 29 5-3/8 inch port and larger for up to 593_C
(1100_F) using Bore Seal trim,
Packing Arrangements
J lubricator/isolating valve for packing lubrication,
J Single, J double, and J leakoff standard and J liner with integral seat ring (EHA Series
packing arrangements, or optional J HIGH-SEAL valves only)
packing systems; see Fisher bulletin 59.1:061,
ENVIRO-SEALt and HIGH-SEAL Packing
Systems for Sliding-Stem Valves Options for NPS 20 Valve
Yoke Boss Diameters for Actuator Mounting Tool Kit: Includes tools useful during
See tables 20 and 21. maintenance [3 sets of lifting eyes, 2 hoist rings,
NPS 8 and 10 CL2500 Valves: 127 mm flushing plate with either J two O-rings for use
(5 inch H(10)) yoke boss diameter when flushing fluid is 149qC (300qF) or less or
All Other Sizes and Ratings: J 127 mm (5 inch J two silver-plated N04400 gaskets for use when
H(10)) or J 178 mm (7 inch) yoke boss diameter flushing fluid is over 149qC (300qF), valve stem
NPS 20 Valve: 178 mm (7 inches) lifting nut, lapping fixture and handle, and tamping
Approximate Weight tools]
Special Cage Characterization: Standard,
See tables 22 and 23
Cavitrol, or Whisper Trim cage openings as
Options necessary to provide the required installed flow
J O-ring seat ring gasket constructions(6), characteristic
1. In flow up applications only, NPS 6 to 14 EHD and EHT and NPS 8 EHAD and EHAT valves are available with a diverter cone valve plug construction to provide increased stability for higher
pressure drops. See figure 11, 16, and 27. Diverter cone valve plug construction is also used for NPS 6 EHD and EHT and NPS 8 EHAD and EHAT applications requiring Whisper Trim III Level
A, B, or C cages. Again, for flow up applications only.
2. EN (or other) ratings and end connections can usually be supplied; please consult your Emerson Process Management sales office.
3. The pressure or temperature limits in this bulletin and any applicable standard limitations should not be exceeded.
4. Modified equal percentage characteristic is equal-percentage for the first 90% of travel, then quick-opening for additional capacity.
5. EHS may be used for flow down in special cases. Please consult your Emerson Process Management sales office NPS 1 and 2 valves with Micro-Form plugs can only be used for flow up
applications
6. O-ring seat ring gasket construction is preferred where temperature allows and is standard for EHT valves. See table 13 and figure 25.
7. For temperatures above 204_C (400_F), the following CF8M (316 SST) valves must be derated: NPS 8 and 10 ASME Special CL1500 or 2500 valves; NPS 12 and 14 ASME Standard or
Special CL2500 valves. For more information, contact your Emerson Process Management sales office.
8. NPS 8 to 14 flow up for boiler feedwater service with pressure drop greater than 69 bar (1000 psi) when a diverter plug is used.
9. Valves using an equal percentage cage may be traveled an additional 13 mm (0.5 inch) if desired to obtain additional capacity; flow characteristic becomes modified equal percentage.
10. H indicates heavy actuator-to-body bolting.
43
Product Bulletin
51.2:EH
Note
Neither Emerson, Emerson Process
Management, nor any of their affiliated
entities assumes responsibility for the
selection, use, or maintenance of any
product. Responsibility for the
selection, use, and maintenance of any
product remains with the purchaser
and end user.
Fisher, Cavitrol, Whisper Trim, and ENVIROSEAL are marks owned by one of the companies in the Emerson Process Management business
division of Emerson Electric Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson
Electric Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they
are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or
applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the
designs or specifications of such products at any time without notice. Neither Emerson, Emerson Process Management, nor any of their affiliated
entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of
any product remains solely with the purchaser and end user.
Emerson Process Management

Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Chatham, Kent ME4 4QZ UK
Dubai, United Arab Emirates
Singapore 128461 Singapore
www.Fisher.com
EFisher
44 Controls International LLC 1982, 2011; All Rights Reserved

Fisher EH and EHA Control Valves PDF

Uploaded by

Copyright:

Available Formats

Fisher EH and EHA Control Valves PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fisher EH and EHA Control Valves PDF

Uploaded by

Copyright:

Available Formats

What types of valves are discussed in the document?

What types of valves are discussed in the document?

What size valves are available?

What size valves are available?

Product Bulletin

Fisherr EH and EHA Control Valves

Figure 1. Fisher EH and EHA Control Valves

Table 1. Availability Chart

For sootblower applications, a special trim design is

D O-ring Seat Ring Gasket Construction—Use D High-Temperature, Class V Shutoff—Use of

D Long Thermal-Cycle Life—The seat ring

D Control Accuracy—The NPS 20 cage and

NPS 1-1/2 x 1 through 6 Globe Valves

Because of flow capacity and severe service

EHA valves--EHAD (figure 9), EHAT (figure 10), and

EH valves are available in CL2500 ratings. EHA

Figure 7. Fisher EHS Trim with Micro-Flute Valve Plug

Figure 10. Fisher EHAT Trim with Whisper Trim III

NPS 8 through 14 Globe Valves

These valves are used for many high-pressure

Figure 13. NPS 8 Fisher EH Valve with Welded Pipe

DIVERTER CONE VALVE PLUG USED IN BOILER

Figure 14. Fisher EHT Trim (NPS 8 through 14 Globe Valves)

O-RING GASKET CONSTRUCTION

Figure 18. Sectional of NPS 20 Fisher EHD Control Valve Assembly

NPS 20 Globe Valves design features to satisfy specific customer

Figure 20. Custom Design Sequence (NPS 20 Globe Valves)

Custom Design Capability (NPS 20 Globe Valves)

C-seal METAL FLOW UP

UPPER SEATING SURFACE

Figure 21. C-seal Trim

C-seal Trim Description Bore Seal Trim Description

FLOW DOWN BORE SEAL

FLOW UP BORE SEAL

Fisher TSO (Tight Shutoff) Trim

Figure 23. Typical Balanced TSO (Tight Shutoff) Trim

TYPICAL FOR ALL GRAPHS

WC9 CHROME-MOLY STEEL VALVES C12A VALVES

Material Selection Guidelines temperature capabilities determined from figures 24,

O-ring Nitrile(5) 29 to 107 20 to 225

Table 15. Valve Plug Travel(1) (NPS 8 through 14 Valves)

BOTH GASKET CONSTRUCTIONS BOTH GASKET CONSTRUCTIONS BOTH GASKET CONSTRUCTIONS

O-RING CONSTRUCTION ONLY O-RING CONSTRUCTION ONLY BOTH GASKET CONSTRUCTIONS

Figure 25. Pressure/Temperature Limits for Trim Material Combinations

PRESSURE DROP, BAR

PRESSURE DROP, BAR

PRESSURE DROP, PSI

FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F

FLUID TEMPERATURE, _C FLUID TEMPERATURE, _C FLUID TEMPERATURE, _C

PRESSURE DROP, BAR, DIFFERENTIAL

PRESSURE DROP, BAR, DIFFERENTIAL

PRESSURE DROP, PSI

PRESSURE DROP, BAR, DIFFERENTIAL

PRESSURE DROP, BAR, DIFFERENTIAL

PRESSURE DROP, PSI

PRESSURE DROP, PSI

FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F

ALL GASKET CONSTRUCTIONS ALL GASKET CONSTRUCTIONS CL2500 VALVE WITH

PRESSURE DROP, PSI

1 and 1-1/4 STEM