Scribd Logo
Upload

Welcome to Scribd!

  • 121 views

    Cebek I 95 User Manual

    Uploaded by

    ulton1237624
    The I-95 module is a 4-8 channel multiplexed emitter used to control I-96 and I-97 receiver modules from up to 600m away using two communication cables. It can independently control up to 8 loads by closing push buttons or switch contacts on the emitter module. No additional power is needed as it operates using the communication cable.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Cebek I 95 User Manual

    Uploaded by

    ulton1237624
    121 views2 pages
    The I-95 module is a 4-8 channel multiplexed emitter used to control I-96 and I-97 receiver modules from up to 600m away using two communication cables. It can independently control up to 8 loads by closing push buttons or switch contacts on the emitter module. No additional power is needed as it operates using the communication cable.

    Original Description:

    ceb

    Original Title

    Cebek i 95 User Manual

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The I-95 module is a 4-8 channel multiplexed emitter used to control I-96 and I-97 receiver modules from up to 600m away using two communication cables. It can independently control up to 8 loads by closing push buttons or switch contacts on the emitter module. No additional power is needed as it operates using the communication cable.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    121 views2 pages

    Cebek I 95 User Manual

    Uploaded by

    ulton1237624
    The I-95 module is a 4-8 channel multiplexed emitter used to control I-96 and I-97 receiver modules from up to 600m away using two communication cables. It can independently control up to 8 loads by closing push buttons or switch contacts on the emitter module. No additional power is needed as it operates using the communication cable.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    ELECTRONIC CIRCUITS

    4-8 CHANNELS MULTIPEXED EMITTER


    The I-95 module is a 4-8 channels multiplexed emitter to control I-96 and I-97 modules. Using two cables,
    I-95
    you could connect emitter and receiver and then independently control up to 8 loads, with 600m as
    maximum distance between emitter and receiver. Communication is done closing push button or switch
    contacts (4 for the I-96 and 8 for the I-97), controlling their corresponding load in the receiver module. As it is
    supplied trough the communication cable, any additional power supply is necessary.

    TECHNICAL CHARACTERISTICS.
    Voltage.................................................................................................................. Not Necessary
    Minimum Consumption........................................................................................ 10 mA.
    Maximum Distance............................................................................................... 600 m.
    To Control Receiver................................................................................................ I-96 & I-97

    OPERATING.
    COMMUNICATION CABLE. As the I-95 module is supplied through the communication cable, this one will be
    the single connection with receivers.
    For industrial installation or with a high parasites level from the mains, you have to use a shielded cable,
    connecting wires to the negative terminal and the interior cable to the positive.

    OPERATING. Connect each "INT" switch to the corresponding terminals as it is indicated in the wiring map.
    Supply the receiver (see the receiver's instruction manual). When these operations will be done, to connect
    wished relay(s) close the corresponding switch or push button.

    CONNECTION MAP.

    INT 1 (RELAY 1)
    INT 8 (RELAY 8)

    INT 7 (RELAY 7)

    INT 6 (RELAY 6)

    INT 5 (RELAY 5)

    INT 4 (RELAY 4)

    INT 3 (RELAY 3)

    INT 2 (RELAY 2)

    COMMUNICATION
    CABLE

    I-95

    1
    AUTOMATISMOS Ref. Full9701
    I-95
    HOW TO INSTALL.

    INT 1 (RELE 1)

    ALIMENTACION

    I-95
    RECEPTOR

    CABLE DE
    COMUNICACION
    INT 2 (RELE 2)

    INT 4 (RELE 4)

    INT 5 (RELE 5)

    INT 6 (RELE 6)

    INT 7 (RELE 7)

    INT 8 (RELE 8)
    INT 3 (RELE3)

    SUGGESTIONS.
    Connection of the Communication cable. You had to correctly connect communication cable
    between emitter and receiver. Do not confuse module input with power supply input. See receiver's

    TECHNICAL SUPPORT AND INFORMATION.


    For any questions or more information:
    By Fax. (24h.) +34.3. 432.29.95
    By Mail: C/ Quetzal, 17-21, Entlo. 2º (08014) BARCELONA - SPAIN.
    By E-Mail: [email protected]
    Keep you invoice. For any repairing could you send this with module. Else, the module will lost the warranty.

    All the module’s CEBEK have 3 years of total warranty in thecnical


    repairing, and spares from the date of buy.
    CEBEK is trade make of FADISEL S.L. more than 300 module’s are avaible in
    stock for any purpose request our CATALOGUE, or visit our Web.
    Http://www.sakma.com/CEBEK Y EAR S
    2

    You might also like