Anchor Bolts (Make-Hilti) PDF

Product Data Sheet
HSA stud anchor
HSA stud anchor
Anchor version Benefits

small edge distance and spacing
three different embedment depth
HSA Carbon steel
for each anchor size
with DIN 125 washer
approved for diamond drilled
HSA-R Stainless holes
steel A4 simple and quick machine setting
HSA-R2 Stainless with torque bar for torque control
steel A2
with DIN 125 washer
HSA-BW Carbon
steel with DIN 9021
washer
A4
316
Concrete Small edge Fire Corrosion Diamond European CE PROFIS
distance resistance resistance drilled Technical conformity anchor design
& spacing holes Approval software
Basic loading data (for a single anchor)

All data in this section applies to
Correct setting (See setting instruction) Minimum base material thickness
Non cracked concrete C 20/25 fck,cube = 25 N/mm2
Steel failure
Recommended loads
Anchor size M6 M8 M10
Effective anchorage depth hef [mm] 30 40 60 30 40 70 40 50 80

Tensile Nrec a)
HAS, HAS-R [Nm] 3.7 4.5 5.4 4.9 7.7 9.6 7.7 10.7 15
Shear Vrec a)
HAS [Nm] 3.7 3.7 3.7 3.9 6.1 6.1 10.8 10.8 10.8
HAS-R [Nm] 4.0 4.1 4.1 3.9 7.0 7.0 12.9 12.9 12.9
Effective anchorage depth hef [mm] 50 65 100 65 80 120 75 100 115

Tensile Nrec a)
HAS, HAS-R [Nm] 10.7 15.9 20.9 15.9 21.7 30.0 19.7 30.4 37.3
Shear Vrec a)
HAS [Nm] 16.9 16.9 16.9 29.1 29.1 29.1 31.2 49.0 49.0
HAS-R [Nm] 16.7 16.7 16.7 32.3 32.3 32.3 31.2 52.5 52.5
shall be taken from national regulations.

page 1 February 2013
Product Data Sheet
HSA stud anchor
Description Authority / Laboratory No. / date of issue

European technical approval a) DIBt, Berlin ETA-11/0374 / 2012-07-19
Fire test report IBMB, Brunswick 3215/229/12 / 2012-08-09
a) All data given in this section according ETA-11/0374, issue 2012-07-19.
Setting details
Nominal anchorage depth hnom [mm] 37 47 67 39 49 79 50 60 90

Minimum base material
thickness hmin [mm] 100 100 120 100 100 120 100 120 160
Minimum spacing smin [mm] 35 35 35 35 35 35 50 50 50
Minimum edge distance c min [mm] 35 35 35 40 35 35 50 40 40

Nominal diameter of
drill bit do [mm] 6 8 10
Cutting diameter of
drill bit dcut [mm] 6.4 8.45 10.45
Depth of drill hole h1 [mm] 42 52 72 44 54 84 55 65 95

Diameter of clearance hole
df [mm] 7 9 12
Torque moment Tinat [Nm] 5 15 25
Width across SW [mm] 10 13 17
Nominal anchorage depth hnom [mm] 64 79 114 77 92 132 90 115 130

Minimum base material
thickness hmin [mm] 100 140 180 140 160 180 160 220 220
Minimum spacing smin [mm] 70 70 70 90 90 90 195 175 175
Minimum edge distance c min [mm] 70 65 55 80 75 70 130 120 120

Nominal diameter of
drill bit do [mm] 12 16 20
Cutting diameter of
drill bit dcut [mm] 12.5 16.5 20.55
Depth of drill hole h1 [mm] 72 87 122 85 100 140 98 123 138

Diameter of clearance hole
df [mm] 14 18 22
Torque moment Tinat [Nm] 50 80 200
Width across SW [mm] 19 24 30

Product Data Sheet
HSA stud anchor
Setting instructions
Drill and clean borehole
Standard drilling method Alternative drilling method

M6 – M20: Hammer drilling (HD) M12 – M20: Diamond drilling (DD)
Install anchor with hammer or machine setting tool
Standard setting method Alternative setting method

M6 – M20: Hammer setting M8 – M16: Machnine setting
For detailed information on installation see instruction for use given with the package of the product.

Product Data Sheet
HSA stud anchor
Machine tightening of the anchor for standard installation torque

Type HSA, HSA-BW, HSA-R2, HSA-R
Anchor size M6 M8 M10 M12 M16 M20
Setting position 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3
Nominal
anchorage depth hnom [mm] 37 47 67 39 49 79 50 60 90 64 79 114 77 92 132 90 115 130
Standard
installation torque Tinat [Nm] - 15 25 50 80 -
Setting tool S-TB HSA S-TB HSA S-TB HSA S-TB HSA
M8 M10 M12 M16
Impact screw driver Hilti SIW 14-A Hilti

Hilti SIW 22-A SIW 22T-A
- -
HSA, HSA-BW 1 1
Speed 3 - 1)
HSA-R2, HSA-R 3 3
Width across tsety [sec.] 4
Setting instruction for HSA, HSA-BW, HSA-R2 and HSA-R M8 – M16

Tightening the anchor - alternatively with imact screw driver and special socket
Selecting the impact screw driver, battery and special socket
Selecting the speed setting and state of charge of the battery
Tighten the anchor and check the installation
For detailed information on installation see instruction for use given with the package of the product.

Anchor Bolts (Make-Hilti) PDF

Uploaded by

Copyright:

Available Formats

Anchor Bolts (Make-Hilti) PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Anchor Bolts (Make-Hilti) PDF

Uploaded by

Copyright:

Available Formats

Product Data Sheet

HSA stud anchor

HSA stud anchor

Anchor version Benefits

Basic loading data (for a single anchor)

Effective anchorage depth hef [mm] 30 40 60 30 40 70 40 50 80

Anchor size M12 M16 M20

Effective anchorage depth hef [mm] 50 65 100 65 80 120 75 100 115

shall be taken from national regulations.

Description Authority / Laboratory No. / date of issue

Nominal anchorage depth hnom [mm] 37 47 67 39 49 79 50 60 90

Minimum spacing smin [mm] 35 35 35 35 35 35 50 50 50

Minimum edge distance c min [mm] 35 35 35 40 35 35 50 40 40

Depth of drill hole h1 [mm] 42 52 72 44 54 84 55 65 95

Torque moment Tinat [Nm] 5 15 25

Width across SW [mm] 10 13 17

Anchor size M12 M16 M20

Nominal anchorage depth hnom [mm] 64 79 114 77 92 132 90 115 130

Minimum spacing smin [mm] 70 70 70 90 90 90 195 175 175

Minimum edge distance c min [mm] 70 65 55 80 75 70 130 120 120

Depth of drill hole h1 [mm] 72 87 122 85 100 140 98 123 138

Torque moment Tinat [Nm] 50 80 200

Width across SW [mm] 19 24 30

page 2 February 2013

Drill and clean borehole

Standard drilling method Alternative drilling method

Install anchor with hammer or machine setting tool

Standard setting method Alternative setting method

page 3 February 2013

Machine tightening of the anchor for standard installation torque

Impact screw driver Hilti SIW 14-A Hilti

Width across tsety [sec.] 4

Setting instruction for HSA, HSA-BW, HSA-R2 and HSA-R M8 – M16

Selecting the impact screw driver, battery and special socket

Selecting the speed setting and state of charge of the battery

Tighten the anchor and check the installation

page 4 February 2013

You might also like