PRODUCTION TECHNOLOGY-I

UNIT NO. 1
Basic tool geometry, single point tool nomenclature, chips-various types and their
characteristics, mechanism of chip formation, theoretical and experimental determination
of shear angle, orthogonal and oblique metal cutting, metal cutting theories,
relationship of velocities, forces and power consumption.
Effect of operating parameters life tool geometry, cutting speed, feed depth of out, coolant,
materials etc on forces temp. Tool life, surface finish etc., tool life relationship, tailor
equation of tool life, tool material and mechanism.

Cutting tool is a device, used to remove the unwanted material from given work piece.

For carrying out the machining process,

Cutting tool is fundamental and essential requirement

Cutting tools are usually classified based on the number of cutting edges -:

1. Single point cutting tool

2. Multipoint cutting tool

Single-point cutting tools have one principal cutting edge. Such tools are classified into
three categories: 1. solid tool, 2. brazed tool, and 3. inserted bit type tool

Cutting Tool Materials

Cermets: Cermets are ceramic material in metal binders. TiC, nickel, TiN, and other

carbides are used as binders. Cermets have higher hot hardness and oxidation resistance

than cemented carbides but less toughness. They are used for finishing operation. The

main problem with cermets is that due to thermal shock the inserts crack.

Diamond: They are of two types - industrial grade natural diamonds, and synthetic
polycrystalline diamonds. Because diamonds are pure carbon, they have an affinity for the

carbon of ferrous metals. Therefore, they can only be used on non-ferrous metals. Feeds

should be very light and high speeds Rigidity in the machine tool and the setup is very

critical because of the extreme hardness and brittleness of diamond.

Cubic Boron Nitride (1962): Cubic boron nitride (CBN) is similar to diamond in

its polycrystalline structure and is also bonded to a carbide base. With the exception of

titanium, or titanium-alloyed materials, CBN will work effectively as a cutting tool on

most common work materials. However, the use of CBN should be reserved for very hard

and difficult-to-machine materials.

Carbon and Medium alloy steels : These are the oldest of the tool materials dating

back hundreds of years. In simple terms it is a high carbon steel (steel which contains about

0.9 to 1.3% carbon). Inexpensive, easily shaped, sharpened. No sufficient hardness and

wear resistance. Limited to low cutting speed operation

High Speed Steel (1900): The major difference between high speed tool steel and

plain high carbon steel is the addition of alloying elements (manganese, chromium,

tungsten, vanadium, molybdenum, cobalt, and niobium) to harden and strengthen the steel

and make it more resistant to heat (hot hardness). They are of two types: Tungsten HSS

(denoted by T), Molybdenum HSS(denoted by M).

Cemented Carbides or Sintered Carbides (1926-30): These

tools are
 Produced by powder metallurgy. Carbide tools are basically of three types:

tungsten carbide (WC), tantalum carbide (TaC), and titanium carbide (TiC).

The carbides or combined carbides are mixed with a binder of cobalt.They are able to

retain hardness to a temperature of about 10000C. So they can be used at high speeds.

Carbide tool are available as brazed tip tools (carbide tip is brazed to steel tool) and inserts

(inserts are of various shapes- triangular, square diamond and round).

Coated cemented carbide (1960): Tool life to about 200 to 300 % or more. A

thin, chemically stable, hard refractory coating of TiC, TiN or Al2O3 is used. The bulk of

the tool is tough, shock resistant carbide that can withstand high temperatures. Because

of its wear resistance, coated tool can be used at still higher speeds.

• Cast cobalt alloys or Stellites (1915): It is a non-ferrous alloy consisting mainly

of cobalt, tungsten and chromium (38% to 53% Cobalt, 30% to 33% Chromium, and 4%

to 20% Tungsten). Other elements added in varying proportions are molybdenum,

manganese, silicon and carbon. It has good shock and wear resistance properties and retains

its harness up to 9000C. Stellite tools can operate at speed about 25% higher than that of

HSS tools .

• Cemented oxides or Ceramic Cutting Tools (1950s): Non-metallic

materials made of pure Aluminum oxide by powder metallurgy. The application ceramic

cutting tools are limited because of their extreme brittleness. The transverse rupture

strength (TRS) is very low. This means that they will fracture more easily when making

heavy interrupted cuts.

 However, the strength of ceramics under compression is much higher than HSS and carbide

tools. It has high hot hardness (up to 1200 degree C), so capable of running at high speeds.

Single Point Cutting Tool Geometry

 Tool signature

It is the system of designating the principal angles of a single point cutting tool.

The signature is the sequence of numbers listing the various angles, in degrees, and the size of

the nose radius.

There are several systems available like American standard system (ASA),

Orthogonal rake system (ORS), Normal rake system (NRS), and

Maximum rake system (MRS).

The system most commonly used is American Standard Association

(ASA), which is:

1.Bake rake angle, 2. Side rake angle, 3. End relief angle, 4. Side relief angle,
5. End cutting Edge angle, 6 . Side cutting Edge angle and 7. Nose radius.

A tool geometry specified as 7-

8-5-6-9-5-1 would mean that :
Back rake angle = 7o, side
rake angle = 8o, end relief
angle = 5o, side relief angle =
6o, end cutting edge angle = 9o,
side cutting edge angle = 5o,
and nose radius = 1mm
 TOOL GEOMETRY IN ASA SYSTEM

Cutting tool angles and their significance

Back rake angle:

•The back rake angle is the angle between the face of the tool and a line parallel to the base of

the shank in a plane parallel to the side cutting edge.

•The back rake angle affects the ability of the tool to shear the work material and form chip.

Side Rake Angles: •It is the angle by which the face of the tool is inclined side way

The Rake Angle: The rake angle is always at the topside of the tool.
The side rake angle and the back rake angle combine to form the effective rake angle. This is

also called true rake angle or resultant rake angle of the tool.

The basic tool geometry is determined by the rake angle of the tool.

Rake angle has two major effects during the metal cutting process. One major effect of

rake angle is its influence on tool strength. A tool with negative rake will withstand far

more loading than a tool with positive rake.The other major effect of rake angle is its

influence on cutting pressure. A tool with a positive rake angle reduces cutting forces by

allowing the chips to flow more freely across the rake surface.

Cutting tool angles and their significance

The rake angle has the following function:

• It allows the chip to flow in convenient direction.

• It reduces the cutting force required to shear the metal and consequently helps to increase

the tool life and reduce the power consumption. It provides keenness to the cutting edge.

• It improves the surface finish.

Positive Rake:

• Positive rake or increased rake angle reduces compression, the forces, and the friction,

yielding a thinner, less deformed and cooler chip.

• But increased rake angle reduces the strength of the tool section, and heat conduction

capacity.

• Some areas of cutting where positive rake may prove more effective are, when cutting

tough, alloyed materials that tend to work-harden, such as certain stainless steels, when
cutting soft or gummy metals, or when low rigidity of workpiece, tooling, machine tool, or

fixture allows chatter to occur.

• The shearing action and free cutting of positive rake tools will often

Negative Rake:

•To provide greater strength at the cutting edge and better heat conductivity, zero or

negative rake angles are employed on carbide, ceramic, polycrystalline diamond, and

polycrystalline cubic boron nitride cutting tools.

•These materials tend to be brittle, but their ability to hold their superior hardness at high

temperature results in their selection for high speed and continuous machining operation.

•Negative rakes increases tool forces but this is necessary to provide added support to the

cutting edge. This is particularly important in making intermittent cuts and in absorbing

the impact during the initial engagement of the tool and work.

•Negative rakes are recommended on tool which does not possess good toughness (low

transverse rupture strength).

•Thus negative rake (or smal rake) causes high compression, tool force, and friction,

resulting in highly deformed, hot chip.

The rake angle for a tool depends on the following factors:

•Type of material being cut: A harder material like cast iron may be machined by smaller

rake angle than that required by soft material like mid steel or aluminum.
•Type of tool material: Tool material like cemented carbide permits turning at very high

speed. At high speeds rake angle has little influence on cutting pressure. Under such

condition the rake angle can minimum or even negative rake angle is provided to increase

the tool strength.

•Depth of cut: In rough turning, high depth of cut is given to remove maximum amount of

material. This means that the tool has to withstand severe cutting pressure. So the rake

angle should be decreased to increase the lip angle that provides the strength to the cutting

edge.

•Rigidity of the tool holder and machine: An improperly supported tool on old or worn

out machine cannot take up high cutting pressure. So while machining under the above

condition, the tool used should have larger rake angle.

Relief Angles

• Relief angles are provided to minimize physical interference or rubbing contact with

machined surface and the work piece.

• Relief angles are for the purpose of helping to eliminate tool breakage and

To increase tool life.

• If the relief angle is too large, the cutting tool may chip or break. If the

angle is too small, the tool will rub against the work piece and generate

excessive heat and this will in turn, cause premature dulling of the cutting
tool.

• Small relief angles are essential when machining hard and strong materials

and they should be increased for the weaker and softer materials.

• A smaller angle should be used for interrupted cuts or heavy feeds, and a larger angle for

semi-finish and finish cuts.

Side relief angle: The Side relief angle prevents the side flank of the tool from rubbing

against the work when longitudinal feed is given. Larger feed will require greater side relief

angle.

End relief angle: The End relief angle prevents the side flank of the tool from rubbing

against the work. A minimum relief angle is given to provide maximum support to the tool

cutting edge by increasing the lip angle. The front clearance angle should be increased for

large diameter works.

Side cutting edge angle:

The following are the advantages of increasing this angle:

• It increases tool life as, for the same depth of cut; the cutting force is distributed on a

wider surface.

• It diminishes the chip thickness for the same amount of feed and permits greater cutting

speed.

• It dissipates heat quickly for having wider cutting edge.

•The side cutting edge angle of the tool has practically no effect on the value of the cutting
force or power consumed for a given depth of cut and feed.

•Large side cutting edge angles are lightly to cause the tool to chatter.

End cutting edge angle: The function of end cutting edge angle is to prevent the trailing

front cutting edge of the tool from rubbing against the work. A large end cutting edge

angle unnecessarily weakens the tool. It varies from 8 to 15 degrees.

Nose radius:

The nose of a tool is slightly rounded in all turning tools. The function of nose radius is as

follows:

• Greater nose radius clears up the feed marks caused by the previous shearing action and

provides better surface finish.

• All finish turning tool have greater nose radius than rough turning tools.

• It increases the strength of the cutting edge, tends to minimize the wear taking place in a

sharp pointed tool with consequent increase in tool life.

• Accumulation heat is less than that in a pointed tool which permits higher cutting speeds
Orthogonal and Oblique Cutting

The two basic methods of metal cutting using a single point tool are the orthogonal (2 D) and

oblique (3D). Orthogonal cutting takes place when the cutting face of the tool is 90 degree to the

line of action of the tool. If the cutting face is inclined at an angle less than 90 degree

to the line of action of the tool, the cutting action is known as oblique.

Orthogonal cutting system

Oblique cutting system

 Orthogonal cutting Oblique cutting system
system

work

work

feed
feed
tool
tool

Orthogonal Cutting: Oblique Cutting:

 The cutting edge of the tool remains normal to  The cutting edge of the tool remains inclined
the direction of tool feed or work feed. at an acute angle to the direction of tool feed
 The direction of the chip flow velocity is or work feed.
Normal to the cutting edge of the tool.  The direction of the chip flow velocity is at an
 Here only two components of forces are angle with the normal to the cutting edge of
acting: the tool. The angle is known as chip flow
Cutting Force and Thrust Force. So the angle.
metal
 Here three components of forces are acting:
cutting may be considered as a two
Cutting Force, Radial force and Thrust Force
dimensional
cutting. or feed force. So the metal cutting may be
considered as a three dimensional cutting.
 The cutting edge being oblique, the shear
force acts on a larger area and thus tool life is
increased.