DI109
DI109
DI109
CIRCUIT DESCRIPTION
Throttle Position ECM The throttle position sensor is mounted in the throttle body and
Sensor detects the throttle valve opening angle.
5V When the throttle valve is fully closed, a voltage of approximate-
VC
VTA ly 0.3 – 0.8 V is applied to terminal VTA of the ECM. The voltage
applied to the terminals VTA of the ECM increases in proportion
to the opening angle of the throttle valve and becomes approxi-
E2 mately 3.2 – 4.9 V when the throttle valve is fully opened. The
ECM judges the vehicle driving conditions from these signals
P24296 A09825 input from terminal VTA, uses it as one of the conditions to de-
cide the air–fuel ratio correction, power increase correction and
fuel–cut control etc.
DTC No. DTC Detection Condition Trouble Area
Condition (a) or (b) continues with more than 5 sec.: Open or short in throttle position sensor circuit
P0120 (a) VTA < 0.1 V Throttle position sensor
(b) VTA > 4.9 V ECM
HINT:
After confirming DTC P0120, use the hand–held tester or OBD II scan tool to confirm the throttle valve open-
ing percentage and closed throttle position switch condition.
Throttle valve opening position expressed as percentage
T bl A
Trouble Area
Throttle valve fully closed Throttle valve fully open
VC circuit open
0% 0%
VTA circuit open or short
WIRING DIAGRAM
T1 ECM
Throttle Position Sensor
5V
G–Y 2 VC
E7
2
9 VTA
Y E7
3
L–B 18 E2
E7
1
A12544
INSPECTION PROCEDURE
HINT:
If different DTCs that are related to different systems are output simultaneously while terminal E2 is
used as a ground terminal, terminal E2 may be open.
Read freeze frame data using the hand–held tester or the OBD II scan tool, as freeze frame data re-
cords the engine conditions when a malfunction is detected. When troubleshooting, it is useful for de-
termining whether the vehicle was running or stopped, the engine was warmed up or not, the air–fuel
ratio was lean or rich, etc. at the time of the malfunction.
1 Connect hand–held tester or OBD II scan tool, and read throttle valve opening
percentage.
PREPARATION:
(a) Connect the hand–held tester or OBD II scan tool to
DLC3.
(b) Turn the ignition switch ON and push the hand–held tes-
ter or OBD II scan tool main switch ON.
CHECK:
Read the throttle valve opening percentage.
OK:
FI7052 Throttle valve opening position
Throttle valve
expressed as percentage
NG
ON
PREPARATION:
(a) Disconnect the throttle position sensor connector.
2
(b) Turn the ignition switch ON.
CHECK:
(+) Measure the voltage between terminal 2 of the throttle position
sensor connector and the body ground.
(–)
OK:
Voltage: 4.5 – 5.5 V
BE6653
A00014 A00106
NG Go to step 5.
OK
OK
PREPARATION:
VTA (+) (a) Remove the glove compartment (See page SF–55).
(b) Turn the ignition switch ON.
CHECK:
Measure the voltage between terminals VTA and E2 of the ECM
connector.
OK:
E2 (–)
Throttle Valve Voltage
A18845
Fully closed 0.3 – 0.8 V
Fully open 3.2 – 4.9 V
OK
PREPARATION:
VC (+)
(a) Remove the glove compartment (See page SF–55).
(b) Turn the ignition switch ON.
CHECK:
Measure the voltage between terminals VC and E2 of the ECM
connector.
OK:
E2 (–)
Voltage: 4.5 – 5.5 V
A18845
OK