Reguli Franare Prin Convertizor

Bosch Rexroth EFC3610 Frequency Inverter
Easy Start Guide
L1 L2 L3 (+) B U V W
The Bosch Rexroth EFC3610 Frequency Inverter range

is available to order from inverterdrive.com
This guide is intended to complement the user manual provided by the manufacturer.
It is provided as a basic introduction to the product for Inverter Drive Supermarket customers.
It should not be used as a replacement for the manual issued by the manufacturer.
This product is not a safety device. All safety considerations including but not
limited to Emergency Stop provision should be assessed separately and are
outside the scope of this guide.
Issue 1
20180621
Easy Start Guide
Bosch Rexroth EFC 3610 Series Inverter
Contents
Page 1 Contents
Page 2 Power and Motor Connections (Single Phase)
Page 3 Power and Motor Connections (Three Phase)
Page 4 Motor Connections - Star and Delta
Page 5 Parameters - Overview
Parameters to set before use
Page 6 How to set a Parameter value
Page 7 How to Operate the Inverter from the keypad
Page 8 How to connect and configure a Potentiometer

for remote speed control
Page 9 How to connect and configure a Run Forward or

Run Reverse switch
Page 10 How to connect and configure a Run/Stop switch

with Forward/Reverse selection
Page 11 How to configure “3-Wire” control with Run/Stop

pushbuttons and Forward/Reverse selection
Page 12 Brake Resistor Connection
Page 13 How to Reset the Inverter to Factory Defaults
This guide has been produced by The Inverter Drive Supermarket Ltd.
All content, including but not limited to graphics, text and procedures copyright © The Inverter
Drive Supermarket and must not be reproduced or altered without prior written permission. Page 1
Easy Start Guide
1. Power and Motor Connections (Single Phase)

Before commencing, confirm that the Inverter and
all cables are completely isolated from the power
supply, have been isolated for at least 5 minutes
and that the motor is not turning.
L1 L2 L3 (+) B U V W
Earth
Earth Phase (W)
Live (L1) Phase (V)
Neutral (L2) Phase (U)
Power Motor
Notes: Important:
The illustration above is based on the 0.75kW Use screened or armoured cable between the
230V model. The terminal layout for other Inverter and Motor and ensure it is grounded
ratings is similar. as shown.
The motor must be separately earthed.
The order of the three motor phases The supply must match the Inverter
determines the initial direction the motor turns. specification.
Easy Start Guide
2. Power and Motor Connections (Three Phase)
Before commencing, confirm that the

Inverter and all cables are completely
isolated from the power supply, have
been isolated for at least 5 minutes and
that the motor is not turning.
Notes:
The illustration on the left is based on the 4kW

400V model. The terminal layout for other
ratings is similar.
The order of the three supply phases is not

important.
The order of the three motor phases

determines the initial direction the motor turns.
This can be reversed by physically swapping
any two motor phases. Or by changing the
Inverter parameters.
Use screened or armoured cable between the

L1 L2 L3 (+) B U V W I n v e r t e r a n d M o t o r . To m i n i m i s e
electromagnetic interference, ensure the
cable screen is grounded as shown.
Earth Screen
Phase (L1) Phase (W) The motor must be separately earthed.
Phase (L2) Phase (V)
Phase (L3) Phase (U) The supply must match the Inverter
specification.
Supply Motor
Easy Start Guide
3. Motor Connections - Star and Delta

Dual voltage induction motors typically include The selection of Star or Delta is not optional
terminal boxes with six points. The points can and must match the supply voltage.
be connected together with links in one of two
ways to suit one of the two rated voltages. Dual voltage motor nameplates include
symbols to represent voltage and full load
The two ways of connecting the links are current in each configuration.
shown below. These are known as “Star” (the Delta is represented by a triangle and star by a
higher voltage) or “Delta” (the lower voltage). Y (Wye).
3.1 Motor connected in STAR (or Wye):
For safety purposes, Star (shown opposite) is

Link STAR the default configuration for small motors
(usually to 3kW) and is sometimes known as
“two at one side”.
Only two links are required for Star. Double-up

the links if changing from Delta to allow the
Phase motor to be changed back in future.
Phase
The order of the three phases determines the
Phase direction the motor turns.
Screen Note that the manufacturer recommends that

the cable screen is earthed at both ends and
Earth the motor and Inverter are earthed separately.
3.2 Motor connected in DELTA:
Link DELTA The link configuration is shown in the

illustration opposite and is sometimes referred
to as “three-a-breast”.
The order of the three phases determines the

direction the motor turns.
Phase Note that the manufacturer recommends that

the cable screen is earthed at both ends and
Phase
the motor and Inverter are earthed separately.
Phase
Screen
Earth
Easy Start Guide
4. Parameters - overview
The Inverter contains a number of settings The parameters contain critical information
which can be changed to tailor it for use in a essential to the correct operation of the
wide range of applications. These settings are Inverter. Therefore, they should at least be
known as parameters. checked by the user before the Inverter is
operated for the first time.
Parameters are typically referred to by code or The parameters listed in section 5 are intended
number (eg. C1.07 = Rated Motor Current) to provide a starting point to allow for basic
with a description available in the manual. operation of the EFC 3610 Inverter.
5. Parameters to set before use

Set the following parameters to allow the EFC If any of the parameters have been changed
3610 to control a motor with Run, Stop and previously, follow the procedure in section 13
Speed Control from the keypad. to reset the Inverter to Factory Defaults.
See section 6 to learn how to set a parameter value.

5.1 Parameters to check and values to set
Parameter Description How to set
b0.00 Access to additional parameters Default is 0 for Basic Parameters. Set to 2 to enable Advanced Parameters.
E0.08 Maximum output frequency (Hz) Maximum frequency of the Inverter. Default is 50.00; suitable for most applications.
E0.09 Output frequency high limit (Hz) Maximum frequency of speed reference (eg. keypad dial). Default is 50.00; suitable for most
applications. Cannot be higher than E0.08.
E0.10 Output frequency low limit (Hz) Default is 0.00; set to 05.00 for most applications .
E0.26 Acceleration time (s) Default is rating dependent; set to 5 for most applications.
E0.27 Deceleration time (s) Default is rating dependent; set to 5 for most applications.
C2.00 V/F curve mode Default is 0 (linear); set to 1 if the motor is driving a Fan or Centrifugal Pump.
C1.05 Rated motor power (kW) Set to match motor nameplate - eg. 0.8 (for 0.75kW)
C1.06 Rated motor voltage (V) Set to match motor nameplate - eg. 230
C1.07 Rated motor current (A) Set to match motor nameplate - eg. 3.34
C1.08 Rated motor frequency (Hz) Default is 50.00. Change to 60.00 for 60Hz motor only - otherwise set at 50.00
C1.09 Rated motor speed (rpm) Set to match motor nameplate - eg. 1380
C0.05 Carrier frequency (Hz) Default is rating dependent and will suit most applications.
Increasing Carrier frequency may reduce motor noise.
Easy Start Guide
6. How to set a Parameter value

6.1 Find Parameter Groups.
This example demonstrates the steps required to set

parameter E0.26 which is Acceleration time in seconds.
Press the “Func” key repeatedly until the display shows

“-b0-” (shown in the illustration opposite). Use the up and
down keys to cycle through the parameter groups.
6.2 Find a Parameter Group eg. E0
There are a total of 17 parameter groups when

“Advanced Parameters” are enabled:-
Some parameter groups may be hidden when “Advanced

Parameters” are not enabled. Press “Set” to select “-E0-”.
6.3 Find a Parameter eg. E0.26
The display will show “E0.00" to indicate parameter 00

within group E0.
Use the up and down keys to navigate to parameter

E0.26. Press the “Set” key to modify the parameter value.
Note that in some cases, the value of a parameter can be

restricted by the value of another parameter.
6.4 Change a Parameter value.
Use the up and down keys to increase or decrease the

value. Press and hold the up or down key to change the
value more quickly.
Press the “Set” key to save changes. The display will
show the next available parameter.Press “Func” twice to
exit.
Note: If the keypad is not used for more than 30 seconds
the display will return to the set point value.
Easy Start Guide
7. How to operate the Inverter from the keypad

7.1 Use the dial to set the required speed.
When the EFC3610 is powered up for the first time without

any changes to the parameters it will operate from the
keypad. The display will change to show the speed
reference in Hz. This is set (as default) by the pot on the
keypad.
The minimum speed reference is defined by parameter

E0.10 and the maximum reference by E0.09.
7.2 Press the green “Run” button to start the motor.
Press the green button firmly to start the motor. The motor
will accelerate to the speed set in 7.1 (above) in the time
defined by parameter E0.26. The display will increase from
0.00 to the speed reference.
Motor speed can be changed whilst the motor is running by

rotating the dial clockwise (faster) or anti-clockwise
(slower). When running, the “Run” lamp will be illuminated.
7.3 Press the red “Stop” button to stop the motor.
The red button will stop the motor. The display will decrease
from the current speed to 0.00. When stopped, the “Run”
lamp will go out and the display will return to the speed
reference value.
The time taken (in seconds) to stop the motor is determined

by parameter E0.27.
Easy Start Guide
8. How to connect and configure a Potentiometer

for remote speed control
If the integrated dial on the keypad is A Potentiometer of 10kOhm rating should be
unsuitable for the application, a remote used.
Potentiometer can be used instead.
This provides the benefit of allowing motor The number of turns depends on the
speed to be controlled from a more convenient application but both single turn and ten turn
location such as a cabinet door (if the EFC Potentiometers are available from The Inverter
3610 is cabinet-mounted) or on the machine Drive Supermarket at InverterDrive.com.
itself.
8.1 Relevant parameters for remote Potentiometer speed control
E0.00 Frequency Setting Source Default is 0 for keypad dial; set to 2 for terminal (remote) control via AI1.
E1.35 AI1 input mode Default is 2 for 0-10V; default is required for this example.
8.2 Connecting the Potentiometer
A wiring diagram is shown in the illustration

opposite. The most important connection at
1 2 3 the Potentiometer end is the centre terminal or
EFC 3610 “wiper”.
I/O Terminal GND AI1 +10V
Blocks The wiper will output a variable voltage
between 0 and 10 volts and should be
connected to the AI1 terminal at the Inverter
end. It is this voltage which provides the speed
Cable signal with 0V being slowest and 10V fastest.
Screen
The default output frequency at 0V is 0Hz and
at 10V is 50Hz.
If the rotation of the Potentiometer is the

opposite to that required (ie. turn anti-
2 3 clockwise to increase speed instead of
1
clockwise) reverse connections +10V and
GND.
Use shielded cable between Potentiometer

10kOhm and Inverter and ensure that the cable screen
Potentiometer is connected to the Inverter earth terminal only.
[Order Code 21302]
Easy Start Guide
9. How to connect and configure a Run Forward or

Run Reverse switch
The parameters described in Section 5 enable This section explains how to enable 2-wire
Run/Stop operation via the red and green control with Run Forward / Stop / Run Reverse
buttons on the Inverter. commands via a single selector switch.
Note that once this procedure is complete, the
If this is unsuitable for the application, a remote Run/Stop buttons on the Inverter can no longer
switch can be used instead. be used.
9.1 Relevant parameters for remote Run/Stop
E0.01 First run command source Default is 0 for keypad. Set to 1 for terminal control on the Inverter.
When set to 1, the FWD lamp will go out.
E1.00 X1 input Default is 35 for Forward Run; default is required for this example.
E1.01 X2 input Default is 36 for Reverse Run; default is required for this example.
E1.15 2-wire / 3-wire control mode Default is 0 for 2-wire forward / stop, reverse / stop; default is required for this example.
X1 X2 SC 24V COM 9.2 Connecting the Switch
3 1 2 A wiring diagram is shown in the illustration

opposite. The SC and COM terminals must be
linked.
EFC 3610
I/O Terminal A suitable 3 position NO (Normally Open)
Blocks switch should be installed between terminals
Link cable 24V, X1 and X2. The centre position should
remain open circuit.
When run forward is selected (24V to X1) the

motor will accelerate from 0 to the currently-
selected speed set point. Run and Fwd lamps
will illuminate. When run reverse is selected
(24V to X2) the behavior is the same but the
motor will run in reverse and the Rev lamp will
123 illuminate instead of Fwd.
When stop is selected (open circuit) the motor

will decelerate to zero and the Run and Fwd
R F lamps will go out. The display will revert to the
current setpoint.
Switch, 3 Position
Normally Open
“Run Forward / Stop / Run Reverse”
Easy Start Guide
10. How to connect and configure a Run/Stop switch

with Forward/Reverse selection
Run/Stop operation via the red and green control with Run/Stop and Forward/Reverse
buttons on the Inverter. commands via separate selector switches.
Note that once this procedure is complete, the
If this is unsuitable for the application, remote Run/Stop buttons on the Inverter can no longer
switches can be used instead. be used.
10.1 Relevant parameters for remote Run/Stop
E0.01 First run command source Default is 0 for keypad. Set to 1 for terminal control on the Inverter
E1.15 2-wire / 3-wire control mode Default is 0. Set to 1 for 2-wire forward / reverse, run / stop.
X1 X2 SC 24V COM 10.2 Connecting the Switches
3 2 1 A wiring diagram is shown in the illustration

linked.
EFC 3610 Two suitable 2 position NO (Normally Open)

I/O Terminal switches should be installed: One between
Blocks Link
cable terminals 24V and X1 (Run/Stop) and the other
between terminals 24V and X2
(Forward/Reverse).
When run is selected (24V to X1) and forward is

selected (X1 open circuit) the display will increase
from 0 to the speed reference as the motor
accelerates and the run lamp will illuminate.
When stop is selected (X1 open circuit) the display

will decrease to zero as the motor decelerates.
31 21 Once at zero, the run lamp will go out. The display
will then revert to the speed reference.
Note: the Forward/Reverse switch only selects the

R direction of rotation - it will not start or stop the
motor.
If the application only requires the motor to turn in

Switch, 2 Position Switch, 2 Position one direction, the Forward/Reverse switch can be
Normally Open Normally Open omitted.
“Run / Stop” “Forward / Reverse”
Easy Start Guide
11. How to configure “3-Wire” control with Run/Stop

pushbuttons and Forward/Reverse selection
Run/Stop operation via the red and green control with Run and Stop commands via
buttons on the Inverter. separate pushbuttons and Forward/Reverse
selection via a selector switch. Note that once
If this is unsuitable for the application, remote this procedure is complete, the Run/Stop
switches can be used instead. buttons on the Inverter can no longer be used.
11.1 Relevant parameters for remote 3-wire control
E0.01 First run command source Default is 0 for keypad. Set to 1 for terminal control on the Inverter
E1.02 X3 input Default is 0; set to 25 to select 3 wire control with reverse select
E1.15 2-wire / 3-wire control mode Default is 0. Set to 2 for 3-wire control mode. If the Inverter displays a PrSE error (conflict)
ensure that parameters E1.00 to E1.02 (see above) have been set first.
X1 X2 X3 SC 24V COM
11.2 Connecting the Switches
1 4 2 3 A wiring diagram is shown in the illustration
linked.
EFC 3610 Link
I/O Terminal cable For “Run” and “Stop”, two suitable
Blocks pushbuttons should be installed. The “Run”
pushbutton should include a Normally Open
contact between terminals X1 and X3 and the
“Stop” a Normally Closed contact between
terminals 24V and X3.
For “Forward/Reverse” a suitable 2 position

NO (Normally Open) switch should be installed
between terminals 24V and X2.
12 23 43
A momentary connection between X1 and X3
will start the motor. It will continue to run until
the connection between 24V and X3 is broken.
R
Note that the Forward/Reverse switch only
selects the direction of rotation - it will not start
or stop the motor. If the application only
Pushbutton Pushbutton Switch, 2 Position
Normally Open Normally Closed Normally Open requires the motor to turn in one direction, the
“Run” “Stop” “Forward / Reverse” Forward/Reverse switch can be omitted.
Easy Start Guide
12. Brake Resistor Connection

Before commencing, confirm that the Inverter and
all cables are completely isolated from the power
supply, have been isolated for at least 5 minutes
and that the motor is not turning.
High inertia loads can cause overvoltage trips A Brake Resistor is first installed to absorb
during deceleration and lead to “OE-3" error braking energy and dissipate it as heat. The
messages. In many cases, the solution is to resistor must be correctly sized for both the
increase the deceleration time to compensate. Inverter and application.
However, if the application requires it, dynamic Then, the “brake chopper” within the Inverter is
braking can be enabled to maintain or reduce enabled. This detects excessive braking
deceleration times by absorbing the energy energy and redirects it to the resistor when
generated by such loads. required.
12.1 Relevant parameters for Dynamic Braking
C0.25 Overvoltage prevention mode Default is 3 for Stall overvoltage protection enabled, resistor braking enabled; default is
required for this example.
12.2 Connecting the Resistor
A wiring diagram is shown in the illustration

opposite. Connect the brake resistor to the B
and (+) Terminals on the Inverter. The order of
the connections is unimportant.
The braking resistor may get hot during

operation. Ensure that it is mounted in a
suitable position at least 10cm away from other
items.
It is important that a resistor of the correct

L1 L2 L3 (+) B U V W rating is used. Consult the manufacturer’s
manual or product listing on InverterDrive.com
(+) B B (+) for further information.
Heat Resistant
Cable
Easy Start Guide
13. How to reset the Inverter to Factory Defaults

13.1 Select the b0 Parameter Group
With the motor stopped, press the “Func” button

repeatedly until the display shows “-b0-” (do not press
and hold the “Func” button).
13.2 Select Parameter b0.10.
Press the “Set” button to select the b0 Parameter group

then use the up button to locate parameter b0.10.
13.3 Change value of b0.10 from 0 to 1.
Press the “Set” button to edit the value of b0.10 and use
the up button to change this from 0 to 1.
Press the “Set” button again to save the changes.
13.4 Finished
The display will show the next parameter for editing

(b0.11).
Press the “Function” button twice to exit from the

parameter menu.
Optional: repeat the process and change b0.10 from 0 to

2 to clear recent fault messages if required.

Reguli Franare Prin Convertizor

Uploaded by

Copyright:

Available Formats

Reguli Franare Prin Convertizor

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Reguli Franare Prin Convertizor

Uploaded by

Copyright:

Available Formats

Bosch Rexroth EFC3610 Frequency Inverter

Easy Start Guide

The Bosch Rexroth EFC3610 Frequency Inverter range

Page 2 Power and Motor Connections (Single Phase)

Page 3 Power and Motor Connections (Three Phase)

Page 4 Motor Connections - Star and Delta

Page 5 Parameters - Overview

Parameters to set before use

Page 6 How to set a Parameter value

Page 7 How to Operate the Inverter from the keypad

Page 8 How to connect and configure a Potentiometer

Page 9 How to connect and configure a Run Forward or

Page 10 How to connect and configure a Run/Stop switch

Page 11 How to configure “3-Wire” control with Run/Stop

Page 12 Brake Resistor Connection

Page 13 How to Reset the Inverter to Factory Defaults

1. Power and Motor Connections (Single Phase)

2. Power and Motor Connections (Three Phase)

Before commencing, confirm that the

The illustration on the left is based on the 4kW

The order of the three supply phases is not

The order of the three motor phases

Use screened or armoured cable between the

3. Motor Connections - Star and Delta

3.1 Motor connected in STAR (or Wye):

For safety purposes, Star (shown opposite) is

Only two links are required for Star. Double-up

Screen Note that the manufacturer recommends that

3.2 Motor connected in DELTA:

Link DELTA The link configuration is shown in the

The order of the three phases determines the

Phase Note that the manufacturer recommends that

5. Parameters to set before use

See section 6 to learn how to set a parameter value.

6. How to set a Parameter value

This example demonstrates the steps required to set

Press the “Func” key repeatedly until the display shows

6.2 Find a Parameter Group eg. E0

There are a total of 17 parameter groups when

Some parameter groups may be hidden when “Advanced

6.3 Find a Parameter eg. E0.26

The display will show “E0.00" to indicate parameter 00

Use the up and down keys to navigate to parameter

Note that in some cases, the value of a parameter can be

6.4 Change a Parameter value.

Use the up and down keys to increase or decrease the

7. How to operate the Inverter from the keypad

When the EFC3610 is powered up for the first time without

The minimum speed reference is defined by parameter

7.2 Press the green “Run” button to start the motor.

Motor speed can be changed whilst the motor is running by

7.3 Press the red “Stop” button to stop the motor.

The time taken (in seconds) to stop the motor is determined

8. How to connect and configure a Potentiometer

8.2 Connecting the Potentiometer

A wiring diagram is shown in the illustration

If the rotation of the Potentiometer is the

Use shielded cable between Potentiometer

9. How to connect and configure a Run Forward or

X1 X2 SC 24V COM 9.2 Connecting the Switch