Weld Stress Calculations Page 1 of 9

Disclaimer: The information on this page has not been checked by an independent person. Use this information at your own risk.
ROYMECH
UK Ta/Mo/W/Nb Fabrication Any part machined/fabricated to drawing or material only supply. www.molyandtantalum.com
Metravib DMA Prüfsysteme Kraftbereiche von 25N bis 450N Frequenzbereiche 1E-5Hz bis 10kHz www.p-d-services.com
Schweißprozessüberwachung Qualitätssicherung u. Dokumentation für das Lichtbogenschweissen www.hks-prozesstechnik.de

Click arrows to page adverts

Home
Formulae_Index
Nomenclature

Weld Strength Calculations

Introduction..... Relevant Standards..... Variables Associated With Welds.....

Guidance Principles..... Table Basic Weld Calcs...... Assessment of Fillet Welds.....
Examples of Fillet Welds Calcs..... Properties of Fillet Welds as lines.....
Example of torsion weld calc. using vectors..... Capacities of Fillet Welds..... Design Strength of Fillet Welds.....

Introduction

The following notes are general guidance notes showing methods of calculation of the strength and size of welds. Welded joints are often
crucially important affecting the safety of the design systems. It is important that the notes and data below are only used for preliminary
design evaluations. Final detail design should be completed in a formal way using appropriate codes and standards and quality reference
documents

Relevant Standards

BS 5950-1:2000 ..Structural use of steelwork in building. Code of practice for design. Rolled and welded sections
BS EN 10025-1:2004 - Hot rolled products of structural steels. General technical delivery conditions

Variables related to welded joints

1. Strength of deposited weld material

2. Type of joint and weld..important
3. Size of weld ..important
4. Location of weld in relation to parts joined..important
5. Types of stress to which the weld is subjected
6. Conditions under which weld is carried out
7. Type of equipment used for welding
8. Skill of welder

Guidance Principles

A generous factor of safety should be used (3-5) and if fluctuating loads are present then additional design margins should be included to
allow for fatigue

Use the minimum amount of filler material consistent with the job requirement

Try to design joint such that load path is not not through the weld

The table below provides provides approximate stresses in, hopefully, a convenient way.

For the direct loading case the butt weld stresses are tensile/ compressive σ t for the fillet welds the stresses are assumed to be shear τ s
applied to the weld throat.

For butt welded joints subject to bending the butt weld stresses result from a tensile/compressive stress σ b and a direct shear stress τ s .
In these cases the design basis stress should be σ r = Sqrt (σ b2 + 4τ s2)

For Fillet welded joints subject to bending the stresses in the fillet welds are all shear stresses. From bending τ b and from shear τ s
In these cases the design basis stress is generally τ r =Sqrt (τ b2 + τ s2)

The stresses from joints subject to torsion loading include shear stress from the applied load and shear stresses from the torque
loading. The resulting stresses should be added vectorially taking care to choose the location of the highest stresses.

http://www.roymech.co.uk/Useful_Tables/Form/Weld_strength.html 12/23/2011
Weld Stress Calculations Page 2 of 9

Table of bracket weld subject to direct and bending stresses

Stress in
Stress in Weld Stress in Weld
Weld
σb σb τb
Method of Loading Weldment Weldment Weldment
τs τs τs
Weld size (h) Weld size (h)
Weld size (h)

Assessment of Fillet Weld Groups ref notes and table Properties of Fillet Welds as lines

Important note: The methods described below is based on the simple method of calculation of weld stress as identified in BS 5950- clause
6.7.8.2 . The other method identifed in BS 5950 - 1 clause 6.7.8.3 as the direction method uses the method of resolving the forces
transmitted by unit thickness welds per unit length into traverse forces (FT ) and longitudinal forces (FL ). I have, to some extent, illustrated
this method in my examples below

The method of assessing fillet welds groups treating welds as lines is reasonably safe and conservative and is very convenient to use.

a) Weld subject to bending....See table below for typical unit areas and unit Moments of Inertia

A fillet weld subject to bending is easily assessed as follows.

1) The area of the fillet weld A u..(unit thickness) is calculated assuming the weld is one unit thick..
2) The (unit) Moment of Inertia I u is calculated assuming the weld is one unit thick..
3) The maximum shear stress due to bending is determined...τ b = M.y/I u

http://www.roymech.co.uk/Useful_Tables/Form/Weld_strength.html 12/23/2011
Weld Stress Calculations Page 3 of 9

4) The maximum shear stress due to direct shear is determined.. τ s = P /A

5) The resultant stress τ r = Sqrt (τ b2 + τ s2 )
6) By comparing the design strength p w with the resultant stress τ r the value of the weld throat thickness is calculated and then the weld
size.
i.e. if the τ r /p w = 5 then the throat thickess t = 5 units and the weld leg size h = 1,414t

a) Weld subject to torsion...See table below for typical unit areas and unit Polar moments of Inertia

A fillet weld subject to torsion is easily assessed as follows.

1) The area of the fillet weld A u (unit thickness) is calculated assuming the weld is one unit thick
2) The (unit) Polar Moment of Inertia J u is calculated assuming the weld is one unit thick.. The polar moment of inertia J = I xx + I yy
3) The maximum shear stress due to torsion is determined...τ t = T.r/J u
4) The maximum shear stress due to direct shear is determined.. τ s = P /A u
5) The resultant stress τ r is the vector sum of τ t and τ s. r is chosen to give the highest value of τ r
6) By comparing the design strength p w with the resultant stress τ r the value of the weld throat thickness is calculated and then the weld
size.
i.e. if the τ r /p w = 5 then the throat thickess t = 5 units and the weld leg size h = 1,414.t

Examples of Fillet Weld Calculations

Example of Weld in Torsion..

P = Applied load = 10 000N

P w = Design Strength = 220 N/mm 2 (Electrode E35 steel S275) Design Strength
b = 120mm.
d = 150 mm
x = b2 / 2(b+d) = 27mm.. (From table below)
y = d2 / 2(b+d) = 42mm..(From table below)

Simple Method as BS 5950 clause 6.8.7.2

Direction Method as BS 5950 clause 6.8.7.3
..The vector sum of the stresses due to forces and moments should not
exceed the design strength Pw L = Length of weld 1 unit thick =
(From table below) b + d = (120 + 150) = 270mm
A u = Unit Throat Area To obtain radius of Force from weld Centre of Gravity (Cog) .
A = 250-27 =223mm
= (From table below) b + d = (120 + 150) = 270mm2
To obtain radius of Force from weld centre of gravity Moment M = P.r = 10000.223 = 2,23.106 N.mm
A = 250-27 =223mm Ju = Polar Moment of inertia for weld 1unit(mm) thick.
Moment M = P.r = 10000.223 = 2,23.106 N.mm = [(b+d)4 - 6b2d2] /12 (b+d) = 1,04.106 mm4 /mm..(From Table)
J u = [(b+d)4 - 6b2d2] /12 (b+d) = 1,04.106..(From Table)
It is necessary to locate the point subject to the highest shear stress..For
a weld subject to only torsion this would be simply at the point furthest
It is necessary to locate the point subject to the highest shear stress..For from the COG. However because the weld is subject to torsion and
a weld subject to only torsion this would be simply at the point furthest
direct shear the problem is more complicated. A normal method of
from the COG. However because the weld is subject to torsion and
determining the stresses in these cases is to use vector addition.
direct shear the problem is more complicated. A normal method of
determining the stresses in these cases is to use vector addition.
It is generally prudent to calculate the total shear stress at both
positions, using the method below, and select the highest.. For this
It is generally prudent to calculate the total shear stress at both
example the method used is to resolve the stresses in the x and y
positions, using the method below, and select the highest.. For this directions
example the method used is to resolve the stresses in the x and y
directions

http://www.roymech.co.uk/Useful_Tables/Form/Weld_strength.html 12/23/2011
Weld Stress Calculations Page 4 of 9

First considering point Z First considering point Z

Horizontal distance from centroid r zh = 120-27= 93mm Horizontal distance from centroid r zh = 120-27= 93mm
Vertical distance from centroid r zv = 42mm Vertical distance from centroid r zv = 42mm

The vertical force /mm run F v = F sv + F tv

The vertical stress τ v = τ sv + τ tv
F sv = P /L = 10000/270 = 37 N/mm run
τ sv = P /A u = 10000/270 = 37 N/mm2 F tv = M.r zh /J u = 2,23.106.93/1,04.106 = 199 N/mm run
τ tv = M.r zh /J u = 2,23.106.93/1,04.106 = 199 N/mm2 F v = 236,45 N/mm run
τ = 236,45 N/mm2
v
The horizontal force /mm run for unit(mm) weld width F h = F sh + F th
The horizontal stress τ h = τ sh + τ th F sh = 0
τ sh = 0 F th = M.r zv /J u = 2,23.106.42/1,04.106 = 90 N/mm run
F h = 90 N/mm run
τ th = M.r zv /J u = 2,23.106.42/1,04.106 = 90 N/mm2 The resultant force on the weld/mm run at z
τ h = 90 N/mm2 F r = Sqrt (F h2 + F v2) = 253 N/mm run
The resultant stress on the weld at z
τ r = Sqrt (τ h2 + τ v2) = 253 N/mm2
Now considering point w

Now considering point w Horizontal distance from centroid r wh = 27mm

Vertical distance from centroid r wv = 150-42= 108mm
Horizontal distance from centroid r wh = 27mm
Vertical distance from centroid r wv = 150-42= 108mm The vertical forces per mm run F v = F sv - F tv
F sv = P /L = 10000/270 = 37 N/mm run
The vertical stress τ v = τ sv - τ tv F tv = M.r wh /J u = 2,23.106.27/1,04.106 = 57,9 N/mm run
τ sv = P /A u = 10000/270 = 37 N/mm2 F v = 20,86 N/mm run
τ tv = M.r wh /J u = 2,23.106.27/1,04.106 = 57,9 N/mm2
The horizontal force /mm run = F h = F sh + F th
τ v = 20,86 N/mm2 F sh = 0
F th = M.r wv /J u = 2,23.106.108/1,04.106 = 231,6 N/mm run
The horizontal stress τ h = τ sh + τ th F h = 231,6 N/mm run
τ sh = 0 The specific force on the weld at w
τ th = T.r wv /J u = 2,23.106.108/1,04.106 = 231,6 N/mm2 F r = Sqrt (F h2 + F v2) = 232,5 N/mm run
τ h = 231,6 N/mm2
The resultant stress on the weld at w
τ r = Sqrt (τ h2 + τ v2) = 232,5 N/mm2 The maximum specific is greatest at z = 253 N/mm run....

Referring to weld capacities for longitudinal stresses PL for fillet welds

The maximum stress is similar but greatest at z .... Capacities of Fillet Welds the weld capacity for a 3mm weld with and
The design strength p w for the weld material is 220 N/mm 2 E35 Electrode S275 Steel is 462N /mm run. This weld would be more
The weld throat thickness should be 253 /220 = 1,15mm . than sufficient.
The weld size is therefore 1,414. 1,15 = 1,62mm use 3mm fillet weld

Example of Weld in Bending..

P= 30000 Newtons
d= 100mm
b= 75mm
y = 50mm
Design Stress p w = 220 N/mm 2 (Electrode E35 steel S275) Design Strength
Moment = M = 30000*60=18.10 5 Nmm

Simple Method as BS 5950 clause 6.8.7.2 Direction Method as BS 5950 clause 6.8.7.3

http://www.roymech.co.uk/Useful_Tables/Form/Weld_strength.html 12/23/2011
Weld Stress Calculations Page 5 of 9

Unit Weld Area = A u = 2(d+b) =2(100+75) =350mm 2 Length of Weld of unit thickness = L = 2(d+b) =2(100+75) =350mm
Unit Moment of Inertia = I u Moment of Inertia / mm throat thickness = I u / mm

= d 2(3b+d) / 6 = 100 2 (3.75 +100) / 6 =5,42.105 mm4 = d 2(3b+d) / 6 = 100 2 (3.75 +100) / 6 =5,42.105 mm 4 / mm

F r = Resultant force per unit length of weld.

τ r = Sqrt(τ s2 + τ b2) F s = Shear force per unit length of weld.
τ s = P / A u = 30000/350 = 85,71 N/mm 2 F b = Bending force per unit length of weld.
τ b = M.y / I u = 18.105 . 50 / 5,42.105 = 166,05 N/mm 2
F r = Sqrt(F s2 + F b2)
τ r = Sqrt(85,71 2 + 166.052) =186,86 N/mm2 F s = P / L = 30000/350 = 85,71 N per mm length of weld
τ r / p w = 186,86 / 220 = 0,85 = Throat Thickness..... F b = M.y / I u
( Throat thickness for τ = 220 N/mm2 ) = 18.105 . 50 / 5,42.105 = 166,05 N per mm length of weld
Leg Length = Throat thickness *1,414 = 1,2mm use 3mm weld
thickness
F r = Sqrt(85,71 2 + 166.052) =186,86 N per mm length of weld.
For this case for the welds under greatest loading the type of loading is
Note : If a leg length h= 1,2mm is used in the equations in relevant part traverse loading. The bending stress is in line with horizontal element
of the "Table of bracket weld subject to direct and bending stresses" and the shear stress is in line with vertical member.
above a value of τ b = 198 N/mm and a value of τ s = 100 N/mm2 The angle of the resulting specific load to the horizontal element
results with a resultant stress of Sqrt (τ b2 + τ s2) = 222N/mm2..Which = arctan(85,71/166,5)= 27,5o.
is in general agreement with the above result
This is an angle with the weld throat θ = 45o + 27,5o = 72,5o

Referring to weld capacities table below.Weld Capacities K is

calculated at 1,36 for this resultant direction of forces.

PT = a.K.pwfor a E35 Weld electrode used with S275 steel

pw = 220 N/mm2 and therefore PT = a*300N/mm2..
A 3mm weld (a = 2,1mm) therefore will therefore have a design
capacity of 630 N/mm run and will easily be able to support the load of
186,86 N per mm run

Properties of weld groups with welds treated as lines -

It is accepted that it is reasonably accurate to use properties based on unit weld thickness in calculation to determine the strength of welds
as shown in the examples on this page. The weld properties Ixx Iyy and J are assumed to be proportional to the weld thickness. The typical
accuracy of this method of calculation is shown below...

This is illustrated in the tabled values below

d b h Ixx Iyy J= Ixx +Iyy

Accurate 3 60 50 955080 108000 1063080

Simple 3 60 50 900000 108000 1008000

http://www.roymech.co.uk/Useful_Tables/Form/Weld_strength.html 12/23/2011
Weld Stress Calculations Page 6 of 9

Error 6% 0 5%

Note: The error identified with this method is lower as h increases relative to d. This error is such that the resulting designs are
conservative.

Example illustrating use of stress vectors

Calculation based on real weld sizes Calculations based on unit values

This calculation uses equations from table below
1) The area of the welds
for Area, centroid, and Ju
(based on throat weld thickness at 0,707.5 = 3,5mm)
1) Area of weld = 0,707.5.(2b+d)
Area = (57.3,5 + 2.55.3,5) = 584,5mm2
Area = 0,707.5.(2.55 + 50) = 565.6mm2
2) The moment of area about x-x =
2) There is no need to calculate the Moment of Area with this method
M of Area = (57.3,5.3,5/2 + 2.55.3,5.(27.5 + 3,5)) = 12 284mm3
3) The centroid v = b2 /(2b+d)
3) The centroid v = Moment of Area/Area

M of Area / Area = 21 mm v = 552/(2.55+50)= 18,9mm

4) The radii rA, rB, rC & rD are calculated .. 4) The radii rA, rB, rC & rD are calculated ..

rA = rB = Sqrt ((58,5-21)^2 + 28,5^2 ) = 47,1 rA = rB = Sqrt ((55-18,9)^2 + 25^2 ) = 43,9

rC = rD = Sqrt ((21)^2 + 28,5^2 ) = 35,40... rC = rD = Sqrt (18,9^2 + 25^2 ) = 31,34

5) The angles θA, θB, θC & θD are calculated .. 5) The angles θA, θB, θC & θD are calculated ..

θA = θB = tan-1 ((58,5-21)/ 28,5 ) = 52,7o θA = θB = tan-1 ((55-18,9)/ 25 ) = 55,29o

θC = θD = tan-1 ((21)/28,5 ) = 36,4o... θC = θD = tan-1 ((18,9)/25 ) = 37o...
6) The direct shear stress on the area = Force /Area 6) The direct shear stress on the area = Force /Area

τ S = 5000/584 = 8,56 N/mm2 τ S = 5000/565,5 = 8,84 N/mm2

7) The Moment on the weld group = Force.Distance to centroid 7) The Moment on the weld group = Force .distance to centroid

M = 5000.(100+21) = 6,05.105Nmm M = 5000.(100+18,9) = 5.94.105Nmm

8) The polar moment of inertia of the weld group = J = Ixx + Iyy 8) The Unit Polar moment of inertia of the weld group =
Ju = 0.707.5.(8.b3 +6bd2+d3)/12 + b4/(2b+d)
Iyy = 2.[55.3,53 /12 + 3,5.55.(50/2 + 3,5/2)2]
+ 573.3,5/12 = 3,3.105mm4 Ju = 0,707.5.(8.553+6.55.502 + 503)/12 - 553/(2.55+50) = 4,69.10
Ixx = 2.[553.3,5/12 + 3,5.55.(55/2 + 3,5 - 21)2]
+ 3,5357 / 12 + 3,5.57.(21-3,5/2)2 = 2,097 .105mm4
J = Ixx +Iyy= 5,4.105mm4 9) The stress due to torsion
τ TA = τ TB = M.rA/J.. and ..τ TC = τ TD = M.rC/J
9) The stress due to torsion
τ TA = τ TB = M.rA/J.. and ..τ TC = τ TD = M.rC/J τ TA = 5,94.105Nmm.43,9mm / 4,69.105mm4=55,6 N/mm2
τ TC = τ TD = 5,945Nmm.31,34mm / 4,69.105mm4= 39,69N/mm2
τ TA = 6.055Nmm.47,1mm / 5,4.105mm4=52,8 N/mm2
τ TC = τ TD = 6.055Nmm.35,4mm / 5,4.105mm4= 39,70N/mm2 10) The resultant stresses τ RA, = τ RB and τ RA, = τ RB
are obtained by adding the stress vectos graphically as shown below
10) The resultant stresses τ RA, = τ RB and τ RA, = τ RB
are obtained by adding the stress vectos graphically as shown below τ RA = τ RB=48,59 N/mm2
τ RC = τ RD = 45,56N/mm2
τ RA = τ RB=46,29 N/mm2
τ RC = τ RD = = 45,31N/mm2

http://www.roymech.co.uk/Useful_Tables/Form/Weld_strength.html 12/23/2011
Weld Stress Calculations Page 7 of 9

Note: The example above simply illustrates the vector method adding direct and torsional shear stresses and compares the difference in
using the unit weld width method and using real weld sizes. The example calculates the stress levels in an existing weld group it is clear that
the weld is oversized for the loading scenario. The difference in the resulting values are in less than 4%. If the welds were smaller i.e 3mm
then the differences would be even smaller.

Table properties of a range of fillet weld groups with welds treated as lines -

Throat Area Location of COG

Weld x I xx-(unit) J-(Unit)
Unit Area y

http://www.roymech.co.uk/Useful_Tables/Form/Weld_strength.html 12/23/2011
Weld Stress Calculations Page 8 of 9

Table Of Weld Capacities

The fillet weld capacity tables related to the type of loading on the weld. Two types of loading are identified traverse loading and longitudinal
loading as show below

The weld loading should be such that

{ (FL/PL) 2 + (FT/PT) 2 } ≤ 1
The following table is in accord with data in BS 5950 part 1. Based on design strengths as shown in table below ... Design Strength

PL = a.pw
PT = a.K.pw

a = weld throat size.

K =1,25 √ (1,5 / (1 + Cos 2 θ )

PT based on elements transmitting forces at 90o i.e θ = 45o and K = 1,25

Weld Capacity E35 Electrode S275 Steel Weld Capacity E42 Electrode S355 Steel
Longitudinal Transverse Longitudinal Transverse
Throat Capacity Capacity Throat Capacity Capacity
Leg Length Leg Length
Thickness Thickness
P L(kN/mm) P T (kN/mm) PL PT
mm mm kN/mm kN/mm mm mm kN/mm kN/mm
3 2,1 0,462 0,577 3 2,1 0,525 0,656
4 2,8 0,616 0,720 4 2,8 0,700 0,875
5 3,5 0,770 0,963 5 3,5 0,875 1,094
6 4,2 0,924 1,155 6 4,2 1,050 1,312
8 5,6 1,232 1,540 8 5,6 1,400 1,750
10 7,0 1,540 1,925 10 7,0 1,750 2,188
12 8,4 1,848 2,310 12 8,4 2,100 2,625
15 10,5 2,310 2,888 15 10,5 2,625 3,281
18 12,6 2,772 3,465 18 12,6 3,150 3,938
20 14,0 3,08 3,850 20 14,0 3,500 4,375
22 15,4 3,388 4,235 22 15,4 3,850 4,813
25 17,5 3,850 4,813 25 17,5 4,375 5,469

Design Strength p w of fillet welds

http://www.roymech.co.uk/Useful_Tables/Form/Weld_strength.html 12/23/2011
Weld Stress Calculations Page 9 of 9

Electrode classification
35 43 50
Steel Grade
N/mm2 N/mm2 N/mm2
S275 220 220 220
S355 220 250 250
S460 220 250 280

Ads by Google
Useful Related Links
Pipe Welding
1. Gowelding..A Real Find..this site has lots of Information on calculating the strength of Welds
2. Weld Design Notes .. A set of excellent design notes Bolt Stress
Calculation

This Page is being developed

Home
Formulae_Index
Nomenclature

Please Send Comments to Roy Beardmore

Last Updated 21/02/2010

http://www.roymech.co.uk/Useful_Tables/Form/Weld_strength.html 12/23/2011