National Conference on Recent Research in Engineering and Technology (NCRRET -2015)

International Journal of Advance Engineer ing and Research Development (IJAERD)

e-ISSN: 2348 - 4470 , print-ISSN:2348-6406

“REVIEW & STUDY PAPER OF UNDERGROUND CABLES FOR 11KV

TRANSMISSION LINE”
1 2 3 4
MAURYA RAJK UMAR R , BHA TT MAY UR V ,SHA RMA VIKAS K , DAVE DHAVAL B
th
1. B.E.(Ele-6 ) Leads Institute Of Technology & Engineering , Matar
2. M.E Electrical Engineering, Parul Institute of Technology, Baroda
[email protected] , [email protected] , [email protected],
[email protected],

Abstract : - Electrical energy is one of the most important voltages. This has made it possible to employ
factors for the developments of any country. But the underground cables for transmission of electric power for
generation of electrical energy is not possible at any short or moderate distance. This review paper focuses on
place. So, to provide ele ctricity from sour ce to load
the various types of cables which are used for the 11kv
transmission line is needed. Generally two types of
power transmission. The design and construction of
transmission line are available. I) Overhead transmission
line & II) Undergrond transmission line. This paper shows underground transmission lines differ from overhead lines
the benefits of underground line over overhead line. because of two significant technical challenges that need
Overhead transmission line has some drawbacks and to be overcome. These are: 1) providing sufficient
increases the efficiency & reliability of transmission line insulation so that cables can be within inches of grounded
underground transmission line is takes place. There are material; and 2) dissipating the heat produced during the
different types of underground cables are available for
operation of the electrical cables. [1]
transmission of electrical power. Here three types of
underground cables are given.
So, this paper shows the details of different kind
of cables and one is suit able for the long transmission
line and
Keywords: - Underground cable, Construction, Different
types of underground cables, Comparison

I. INTRODUCTION
This overview contains information about electric
transmission lines which are installed underground, rather
than overhead on poles or towers. Underground cables
have different technical requirements than overhead lines
and have different environmental impacts.
Fig.1 .1 Diagram Underground Cable s [2]
“An underground cable essentially consists of one or more
core/conductor covered with suitable insulation and
surrounded by a protective covers.”
The underground cables has several advantages over
overhead line like less effect or damage though lighting,
less maintenance cost, less chance of fault, smaller
voltage drop, better general appearance & most r eliable.
In a modern power system for power distribution,
generally used underground cables. However recent
improvement in the d esign & manufacturing has leaded
the development of the cable suitable for used at high
 Fig.1 .2 Simulation of underground cable & Overhead
line [2]
Properties Unit Copper Aluminium

Density g/cm3 8.89 2.703

II. GENERAL CONSTRUCTION OF CABLE

Resistivity Oh. 17.241 28.264
Mm2 /Km Table 2: Comparison of Cable properties [3]

In general construction of cable following contains is

Constant ̊
1/ C 0.00393 0.00403
included:
mass
 Core/conductor
temperature
 Insulation
coefficient
 Metallic Sheath
 Bedding
 Armouring
Conductivity Siemens 58 36  Serving

m/mm2

Temperature 234.5 228

coefficient
at ̊C ̊C

Specific heat 0.389 0.8870

per unit
weight w/g/ ̊ C

Coefficient ̊
1/ C 17x106 23x10-6
of linear Fig.2.1 Details of Underground Cable [3]
A) Conductor:-
expansion
Generally conductor are made up of copper/aluminium
with a circular, compacted & stranded. Copper and
aluminium are used to provide sufficient flexibility in
stranded form. Cable mainly consists of one, two, thr ee or
four conductor depending upon service required.
B) Insulation:-
In a laid underground conductor, it is used to provide a
sufficient thickness of insulation and it depends upon the
voltage level.
Insulation provides following properties : - High
insulation resistance to avoid leakage current, High
dielectric strength to avoid electrical breakdown of the
cable, high mechanical strength.

2
Different material used for cable insulation: - Rubber, charging currents and earth-leakage currents in networks
V.I.R (Vulcanized India Rubber), Impregnated paper, P.V.C without the rigid star- point earthing. Its characteristic
(Polyvinyl chloride). differs its property from other cables, which can be given
C) Metallic sheath:- as:
This layer of underground cable insulates with the -- Its excellent electrical and physical properties.
presence of soil, moisture, gases, and some other liquids,
in order to protect the cable metallic sheath made up of --Capability of Carrying Large Currents The excellent
lead or aluminium to provide over the insulation. resistance to ther mal deformation and the excellent aging
D) Bedding:- property of XLPE cable permit it to carry large currents
Bedding is provided to cable the cable from corrosion and under normal (90ºC), emergency (130ºC) or short circuit
some mechanical injuries. It is made up of jute or hessian (250ºC) conditions
tape. -- Ease of Installation XLPE cable withstands smaller radius
E) Armouring:- bending and is lighter in weight, allowing for easy and
It consists of one or two layers i.e. galvanised steel wire or reliable installation. Furthermore, the splicing and
steel tape, to protect the cable from mechanical injuries terminating methods for XLPE cable are simpler in
while handling. comparison with other kinds of cables.
F) Serving:- --Free from Height Limitation and Maintenance XLPE
It is the outermost part of the cable, wiz made of some cables can be installed anywhere without special
fibrous material like jute in order to protect the armouring consideration of the route profile (height limitations)
from atmospheric condition. since it does not contain oil and thus is free from failures
due to oil migration in oil -filled cables.
III. Types of underground cables for 11kv that can list --No Metallic Sheath Required XLPE cable does not
are as follows:- generally demand a metallic sheath. Thus it is free from
the failures peculiar to metallic-sheathed cables, such as
1. Cross-linked polyethylene(XLPE) corrosion and fatigue.

2. Self-contained fluid-filled(SCFF)

3. High-pressure Gas-filled (HPGF)

4. Polyvinyl chloride (PVC)

1) Cross-linked polyethylene (XLPE) Cable:-

XLPE is an abbreviated designation of “cross -linked

polyethylene”. Cross linked polyethylene is produced
from polyethylene under high pressure with organic
peroxides as additives. The application of heat and
pressure is used to effect the cross linking. This causes the
individual molecular chains to link with one another which
in turn causes the material to change from a
thermoplastic to an elastic material.
An important advantage of XLPE as insulation for medium
and high voltage cables is their low dielectric loss. The
dielectric loss factor is about one decimal power lower
than that of paper insulated cables and about two decimal
powers lower than that of PVC- insulated cables. Since the
dielectric constant is also more favorable, the mutual
capacitance of XLPE cables is also lower, thus reducing the

3
 use is diminishing worldwide. A fluid channel in the
middle of the conductor (between the cores of three-
conductor cable) permits the dielectric oil expansion and
the contraction under pressure, inhibiting insulation voids
from forming. It contains the positive internal pressure
(15- 75psig, 0.1-0.5MPa) and an insulating jacket is put
over the sheath.

Fig: 3.1 [XLPE CABLE] [6]

- On the XLPE cables, high voltage test at room Fig: 3.2[SCFF CABLE] [2]
temperature is performed by testing the cables to
withstand a voltage of 3kv ac at a frequency of 40 to 60 Hz
or an ac voltage of 7.2 KV. It is kept under temperature of 3) High-pressure Gas-filled (HPGF) Cable:-
82 ±2 ̊C for 14 days and the maximum water absorbed
value is 1 mg/cm2.[6] HPGF cable is the modified version of HPFF cable, this
system utilized a pressurized gas (Nitrogen) filled pipe
instead of the fluid-filled pipe. It is highly reliable, not
complex, trouble free-system with a proven long term
track record for new bulk power transmission circuit in
the 69kv to 500kv range, as an alternative to solid
dielectric cables, It is more preferable in underground
high voltage transmission cable because of its multiple
2) Self-contained Fluid-filled (SCFF) Cable:- layer of insulating tapes produce a uniform laminated
insulation wall, minimizing effect of any abnormalities in
SCFF cables are laminar paper or LPP insulation. These the insulation wall, as compared to an extruded insulation
cables can be manufactured in very long splice free length solid dielectric cable and its longer length of 4000 feet
which makes them useful for submarine projects, through minimizes the number of manholes, splices and cost.

4
These cables can be over insulated to allow future
operation at a higher system voltage. A number of circuit
have been installed in this fashion and operated at a
lower voltage initially for years and then later switched to
the higher operating voltage when greater MVA system
capacity was required of the feeder.

HPGF cables are very similar in design to HPFF cables

except:

a) The insulation thickness are greater as shown in

table below due to the lower electrical strength
of gas as compared to fluid;

Paper Insulation Thickness [4]

Voltage HPGF HPFF

69KV 0.300” 0.270”

115KV 0.485” 0.375”

138KV 0.585” 0.440”

b) The cable impregnate used in HPGF cables is a far

more viscous fluid to minimize the drainage of
the impregnate from the insulating tapes.

Fig: 3.3[HPGF CABLE][4]

It provides the high reliability, ruggedness without a
liquid in a pipe, which eliminates the environment
concern. It also extremely low magnetic field (1 to 2 4) Polyvinyl chloride (PVC) insulated cable:-
milligausses) as confirmed by industry tests and data. This
is about 50 times lower than 1/C solid dielectric cables They are commonly abbreviated as PVC’s , widely used in
installed in duct banks or direct buried. The Nitrogen gas various fields. It is relatively at low cost, biological and
used in this cable is pressurize of 200 psig prevents chemical resistance which being used in various
ionization in service under normal and emergency applications. Low voltage copper conductor PVC cables
operating condition with a low cost, thus this unit are extremely used for domestics home appliances wiring,
contains only three pressure switches for hi -low— house wiring and internal wiring for lighting circuits in
Emergency alarms, one nitrogen pressure regulator and factories, in control, instrumentation, submarine, etc. Due
two nitrogen cylinders. to its high tensile strength, superior conductivity, better
flexibility & ease joining.

PVC CABLES

I. Railway signaling & auto cables

II. Power cables Upto 61 cores

5
 III. Flat cables for submersible pumps

IV. FRLS/FR/HR/Fire survival cables

IV. Comparison of Cables:-
This type of cable is mainly thin insulated and used in LT
side cables. It’s have a tensile strength from 20-30 N/mm2
FACTO RS SAMPLE SAMPL SAMPLE 3 SAMPLE
& elongation is of 300-400 %. The permanent elongation 1 E2 4
can be in negative value with maximum limit of 12%, its PVC
insulation thickness is 7.11mm and wire thickness XLPE HPGF CABLE SCFF
CABLE CABLE CABLE
1.88mm. The treatment given to PVC cables constitute of
keeping cables under temperature of 80±2˚C, 100±2˚C, INSULATIO N XLPE PAPER PVC CRAFT
135±2˚C for Type A, Type B & Type C insulation PAPER

respectively for 7 days. Mainly PVC cables are used under NO . O F CORE Multi 3 core Multi 3 core
these cold conditions, the insulation resistance constant is
around 36.7MΩ Km at 27˚C and 0.036 MΩ Km at
OPERATING Upto Upto Upto 33kv Upto
maximum rated temperature.
VO LTAGE 500kv 345kv 138kv
RATING

VO LTAGE 4-5% more 5-6% 3-5% on on normal

DROP than pvc on normal Op. Op. Temp
normal Temp
Op.
Temp

SHORT CKT 250 ˚C 250 ˚C 160 ˚C 160 ˚C

TEMP.RATING

OPERATING Upto 110 Upto Upto 75 ˚C Upto 85 ˚C

TEMP ERATUR ˚C 105 ˚C
E

ARMOURING Metal wire Unarmo PVC PVC/Nylo

armoring ured Armoring n Armore d

COST LESS HIGH VERY LESS

LESS

SERVICE LIFE Long Very Long Me dium

Long

Fig: 3.4[PV C CABLE][5]

6
V. CONCLUSION

This review and study paper concludes that from the

above cables XLPE cable is most suitable than HPGF, PVC
& SCFF for the long transmission line because it is
available on very high voltage rating Upto 500kv and its
service life is also long. The operating temperature of
XLPE cable is high (Upto 110 ̊ C) and short circuit
temperature rating is also high (Upto 250 C̊ ) and cost of
XLPE Cable is also less as compared to HPGF Cable. So, on
the basis of these featur es XLPE Cable is more sui table for
long underground transmission line.

VI. REFERANCES

[1] Public Service Commission of Wisconsin, Madison, WI

53707-7854

[2] E.C. Bascom III, V.D. Antoniello,” Underground Power

Cable Consideration: Alternative to Overhead.

[3] Mantosh Kumar, Prof. R.N.Sharma,” Underground

Cable construction: Survey”

[4] Pipes type cables by OKONITE COMPANY.

[5] Vigya, Comparison of cables.

[6] Shinji Umeda, Hiroji Akasaka, “Underground Power

Cable, Distribution Cable Overhead.”