Licensed Copy: Mr.

Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

BS EN 14617-1:2013

BSI Standards Publication

Agglomerated stone — Test

methods
Part 1: Determination of apparent density
and water absorption

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

raising standards worldwide™

 BS EN 14617-1:2013 BRITISH STANDARD
Licensed Copy: Mr. Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

National foreword
This British Standard is the UK implementation of EN 14617-1:2013.
It supersedes BS EN 14617-1:2005 which is withdrawn.
The UK participation in its preparation was entrusted to Technical
Committee B/545, Natural stone.
A list of organizations represented on this committee can be
obtained on request to its secretary.
This publication does not purport to include all the necessary
provisions of a contract. Users are responsible for its correct
application.
© The British Standards Institution 2013. Published by BSI Standards
Limited 2013
ISBN 978 0 580 79618 0
ICS 91.100.15
Compliance with a British Standard cannot confer immunity from
legal obligations.
This British Standard was published under the authority of the
Standards Policy and Strategy Committee on 30 April 2013.
Amendments issued since publication
Date Text affected
 BS EN 14617-1:2013

EUROPEAN STANDARD EN 14617-1

Licensed Copy: Mr. Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

NORME EUROPÉENNE
EUROPÄISCHE NORM April 2013

ICS 91.100.15 Supersedes EN 14617-1:2005

English Version

Agglomerated stone - Test methods - Part 1: Determination of

apparent density and water absorption

Pierre agglomérée - Méthodes d'essai - Partie 1 : Künstlich hergestellter Stein - Prüfverfahren - Teil 1:
Détermination de la masse volumique apparente et du Bestimmung der Rohdichte und der Wasseraufnahme
coefficient d'absorption d'eau

This European Standard was approved by CEN on 1 March 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14617-1:2013: E
worldwide for CEN national Members.
 BS EN 14617-1:2013
EN 14617-1:2013 (E)
Licensed Copy: Mr. Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

Contents Page

Foreword ..............................................................................................................................................................3
1 Scope ......................................................................................................................................................4
2 Terms and definitions ...........................................................................................................................4
3 Apparatus ...............................................................................................................................................4
4 Preparation of the specimens ..............................................................................................................4
4.1 Sampling .................................................................................................................................................4
4.2 Specimen conditioning .........................................................................................................................4
5 Test procedure .......................................................................................................................................5
6 Expression of results ............................................................................................................................5
7 Test report ..............................................................................................................................................5
Bibliography ........................................................................................................................................................7

2
 BS EN 14617-1:2013
EN 14617-1:2013 (E)
Licensed Copy: Mr. Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

Foreword
This document (EN 14617-1:2013) has been prepared by Technical Committee CEN/TC 246 “Natural stones”,
the secretariat of which is held by UNI.

This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2013, and conflicting national standards shall be withdrawn at
the latest by October 2013.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 14617-1:2005.

Subclause 5.1 has been modified since the last edition of this European Standard.

This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.

This European Standard is one of a series of standards for test methods for agglomerated stones which
includes the following parts:

 Part 1: Determination of apparent density and water absorption

 Part 2: Determination of flexural strength (bending)

 Part 4: Determination of the abrasion resistance

 Part 5: Determination of freeze and thaw resistance

 Part 6: Determination of thermal shock resistance

 Part 8: Determination of resistance to fixing (dowel hole)

 Part 9: Determination of impact resistance

 Part 10: Determination of chemical resistance

 Part 11: Determination of linear thermal expansion coefficient

 Part 12: Determination of dimensional stability

 Part 13: Determination of electrical resistivity

 Part 15: Determination of compressive strength

 Part 16: Determination of dimensions, geometric characteristics and surface quality of modular tiles

According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

3
 BS EN 14617-1:2013
EN 14617-1:2013 (E)
Licensed Copy: Mr. Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

1 Scope
This European Standard specifies a method for determining the apparent density and water absorption of
agglomerated stone products.

2 Terms and definitions

For the purposes of this document, the following terms and definitions apply.

2.1
apparent density
Mv
3
ratio between mass (expressed in kg) and apparent volume (expressed in m ) situated within the external
surface of the body

2.2
water absorption
C
maximum amount of water absorbed by the material when soaked in deionised water at room temperature
and pressure according to the procedure described below, expressed as a percentage of the dry mass of the
sample

3 Apparatus
3.1 A covered tank with a flat base comprising small non-oxidising and non-absorbent supports for the
specimens.

3.2 A device able to maintain a constant water level in the tank, described in 4.1.

3.3 A time counter with an accuracy of one second.

3.4 A weighing instrument with an accuracy of 0,01 % of the sample mass.

3.5 A hydrostatic balance accurate to at least 0,01 % of the sample mass.

3.6 A ventilated oven capable of maintaining a temperature of (70 ± 5) °C.

4 Preparation of the specimens

4.1 Sampling

The sampling is not the responsibility of the test laboratory except where especially requested. At least six
specimens selected from a homogeneous batch consisting of the same material mixture should be tested. The
final finishing of the specimen should be the same as the end product (sand blasted, gauged or polished
surface) but without chemical surface treatment. The dimensions of the sample are (100 x 100) mm length
and width and (10 ± 2) mm thickness.

4.2 Specimen conditioning

The specimens should be dried in a stove at (70 ± 5) °C until the difference between two successive
weighings at (24 ± 2) h intervals is less than 0,1 % of the sample mass. The specimens shall be kept in a
desiccator until room temperature (20 ± 5) °C is attained.

4
 BS EN 14617-1:2013
EN 14617-1:2013 (E)
Licensed Copy: Mr. Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

5 Test procedure
After drying and weighing (Mo), place the specimens in a tank on two supports in order to reduce the support
contact surface to a minimum.

Slowly pour the deionised water into a container until the specimens are completely immersed and covered by
2 cm of water. After (1 ± 0,25) h, (8 ± 0,5) h and (24 ± 1) h from the beginning of the tests, and later at regular
intervals of (24 ± 1) h, take the specimens out of the water, wipe with a damp cloth and weigh them in air.
Continue to immerse the specimens in water and repeat the tests until the weight variation specimens (Mt) in
three successive weighings is less than 0,1 %.

Immediately after the final weighing of each sample, determine the apparent mass (Ma) by weighing the
sample in water using a hydrostatic balance.

6 Expression of results
3
6.1 The apparent density Mv, in kg/ m is given by:

M o × ρ H2O
Mv = (1)
(M t − M a )

where

Mo is sample mass weighed in air after drying, in kilograms;

Mt is sample mass soaked in water (6), wiped by a damp cloth and weighed in air, in kilograms;

Ma is sample mass soaked in water and weighed in water, in kilograms;

ρH2O is the true density of water at the measuring temperature, in kilograms/ cubic metre.

6.2 Water absorption C in percentage (%) is given by:

100 × (M t − M o )
C= (2)
Mo

6.3 For a more complete documentation of water absorption of a material, the amount of water absorbed
relative to 1 h, 8 h, 24 h, 48 h, 72 h, etc. can be calculated. The amount of water absorbed (Ci in percent) at
the generic time ti is given by:

100 × (M i − M o )
Ci = (3)
Mo

where

Mi is sample mass weighed in air after ti time of water absorption.

Porosities (open and total) may be calculated according to EN 1936.

7 Test report
The test report shall contain the following information:

a) unique identification number of the report;

5
 BS EN 14617-1:2013
EN 14617-1:2013 (E)
Licensed Copy: Mr. Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

b) number and year of issue of this European Standard, i.e. EN 14617-1:2013;

c) name and address of the test laboratory and the address where the test was carried out if different from
the test laboratory;

d) name and address of the client;

e) it is the responsibility of the client to supply the following information:

1) name of the supplier;

2) name of the person or organisation which carried out the sampling;

3) surface finish of the specimens (if relevant to the test);

4) nature of the binders;

f) date of delivery of the sample or of the specimens;

g) date when the test specimens were prepared (if relevant) and the date of testing;

h) number of specimens in the sample;

i) dimensions of the specimens;

j) apparent density values of each specimen and the average value;

k) water absorption value of each specimen and the average value;

l) all deviations from the standard and their justification;

m) remarks.

The test report shall contain the signature(s) and role(s) of the responsible(s) for the testing and the written
consent of the test laboratory. It shall also state that the report shall not be partially reproduced without the
written consent of the test laboratory.

6
 BS EN 14617-1:2013
EN 14617-1:2013 (E)
Licensed Copy: Mr. Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

Bibliography

[1] EN 1936, Natural stone test methods — Determination of real density and apparent density, and of
total and open porosity

[2] EN 12440, Natural stone — Denomination criteria

[3] EN 14618, Agglomerated stone — Terminology and classification

7
 Licensed Copy: Mr. Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

This page deliberately left blank

 Licensed Copy: Mr. Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

This page deliberately left blank

Licensed Copy: Mr. Universiti Teknologi Malaysia User, Universiti Teknologi Malaysia, 02/08/2013 06:49, Uncontrolled Copy, (c) The British Standards Institution 2013

British Standards Institution (BSI)

BSI is the independent national body responsible for preparing British Standards and other
standards-related publications, information and services. It presents the UK view on standards in
Europe and at the international level.
BSI is incorporated by Royal Charter. British Standards and other standardisation products are
published by BSI Standards Limited .

Revisions Information on standards

British Standards and PASs are periodically updated by amendment or BSI provides a wide range of information on national, European
revision. Users of British Standards and PASs should make sure that they and international standards through its Knowledge Centre.
possess the latest amendments or editions. Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005
It is the constant aim of BSI to improve the quality of our products and Email: [email protected]
services. We would be grateful if anyone finding an inaccuracy or ambiguity
while using British Standards would inform the Secretary of the technical BSI Subscribing Members are kept up to date with standards developments
committee responsible, the identity of which can be found on the inside front and receive substantial discounts on the purchase price
cover. Similary for PASs, please notify BSI Customer Services. of standards. For details of these and other benefits contact Membership
Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Administration.
Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001
BSI offers BSI Subscribing Members an individual updating service called Email: [email protected]
PLUS which ensures that subscribers automatically receive the latest editions
of British Standards and PASs. Information regarding online access to British Standards and PASs
Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001 via British Standards Online can be found at
Email: [email protected] www.bsigroup.com/BSOL
Further information about British Standards is available on the BSI website
Buying standards at www.bsi-group.com/standards
You may buy PDF and hard copy versions of standards directly using a
credit card from the BSI Shop on the website www.bsigroup.com/shop.
In addition all orders for BSI, international and foreign standards publications
Copyright
All the data, software and documentation set out in all British Standards and
can be addressed to BSI Customer Services.
other BSI publications are the property of and copyrighted by BSI, or some
Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 person or entity that own copyright in the information used (such as the
Email: [email protected] international standardisation bodies) has formally licensed such information
to BSI for commerical publication and use. Except as permitted under the
In response to orders for international standards, BSI will supply the British Copyright, Designs and Patents Act 1988 no extract may be reproduced,
Standard implementation of the relevant international standard, unless stored in a retrieval system or transmitted in any form or by any means –
otherwise requested. electronic, photocopying, recording or otherwise – without prior written
permission from BSI. This does not preclude the free use, in the course of
implementing the standard, of necessary details such as symbols, and size,
type or grade designations. If these details are to be used for any other
purpose than implementation then the prior written permission of BSI must
be obtained. Details and advice can be obtained from the Copyright &
Licensing Department.
Tel: +44 (0)20 8996 7070
Email: [email protected]

BSI
389 Chiswick High Road London W4 4AL UK
Tel +44 (0)20 8996 9001
Fax +44 (0)20 8996 7001
www.bsigroup.com/standards

raising standards worldwide™