Experiment 4 - FM Demodulation PDF
Experiment 4 - FM Demodulation PDF
Experiment 4 - FM Demodulation PDF
Group No Grade
Student number
and name
Student number
and name
Student number
and name
Experiment 4
Frequency Demodulator
Preliminary Work
1. In the laboratory, you will use Function Generator as VCO. You are free to choose the
frequency and magnitude of the carrier and message signals.
3. Build your active filter in PSpice and plot the transfer function of it.
4. Design an envelope detector to extract the information from the signal at the output of
the slope detector. (You are asked to simulate only the filter in PSpice not the
entire circuit!)
ATTENTION
• Each group will submit only one report which will be completed on this experiment
document.
1 THEORY
In this experiment you will demodulate the FM signal using either slope detector or phase
locked loop (PLL).
1
EED314 Analog Communication- 2013 Spring Experiment 4
dB dB
amplitude
ω1 ω1
amplitude modulation
modulation
ω ω
frequency ω0 ω0 frequency
modulation modulation
Modulation
FM + AM Filter AM Envelope
signal+AM
Noise Slope detector
Noise
(with a corner frequency ω1 ) at ω0 and take a frequency deviation of δω. The filter response is
therefore:
Vo 1 1 ω1
= H (ω) = ≈ = ω ≫ ω1 (1)
Vi 1 + jω/ω1 jω/ω1 ω
Notice that for a frequency deviation of +/- 10% of the center frequency ( δω
ω0 = 0.1), the
second order component is only 10x below the first order component resulting in a -20 dB
2
EED314 Analog Communication- 2013 Spring Experiment 4
distortion level. Therefore, this technique is valid only for a small frequency deviation from the
center frequency (e.g. δω
ω0 = 3%). Another pitfall of this technique is that it does not have any
rejection of unwanted AM signals (noise). If a high pass filter is used, the demodulation process
is much more linear since the high-pass function is:
Vo jω/ω2 jω ω
= H(ω) = ≈ = for ω << ω2 high-pass filter (4)
Vi 1 + jω/ω2 ω2 ω2
which is a linear process. However, this technique still suffers from having no rejection to AM
noise.
where m(t) is the message signal, the demodulation process will use the phase-locked loop
method:
y(t) m(t)
Phase detector Low-pass filter
VCO
You can use LM565 PLL IC. As long as the frequency deviation of the FM signal does not
cause the PLL to exceed its tracking range, the output at the modulator and the VCO output
of the PLL at the demodulator should remain frequency locked together.
2 PROCEDURE
a. Build the circuit you designed in your preliminary.
b. Measure the frequency and amplitude of your message signal. Note them below.
amplitude=
frequency=
c. Measure the frequency and amplitude of your carrier signal. Note them below.
3
EED314 Analog Communication- 2013 Spring Experiment 4
amplitude=
frequency=
d. Now connect the 50Ω output of the signal generator of message signal to the sweep input
of the carrier signal generator. Obtain the FM output from the 50Ω output of the signal
generator of the carrier signal
e. Observe the output of your FM demodulator circuit. Draw both message and demodulated
signal below.
Volt/div=
time/div=
4
EED314 Analog Communication- 2013 Spring Experiment 4
3 Conclusion
3.1 Student Name and ID:
5
EED314 Analog Communication- 2013 Spring Experiment 4
6
EED314 Analog Communication- 2013 Spring Experiment 4