Code No: K1924 Set No.

1
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. II Sem., I Mid-Term Examinations, February – 2012
ELECTRONIC MEASUREMENTS AND INSTRUMENTATION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.

I Choose the correct alternative:

1. Duty cycle of square wave is [ ]

(A) 25% (B) 75% (C) 50% (D) 100%

2. Frequency range of AF Signals [ ]

(A) 20Hz – 20KHz (B) 20KHz – 200KHz (C) 30KHz – 300KHz (D) 10KHz- 100KHz

3. Wave analyzer is used in _______measurements [ ]

(A) Electrical (B) Sound (C) Vibration (D) All the above

4. The purpose of synchronizing control in CRO is to [ ]

(A) Focus the spot on screen (B) Lock the display of signal
(C) Adjust amplitude of display (D) Control the intensity of spot

5. Errors due to human mistakes are ______ [ ]

(A) Gross errors (B) Systematic error (C) Instrumental errors (D) Environmental errors

6. In signal generator_______ [ ]
(A) Energy is created (B) Energy is generated
(C) Energy is converted from a DC source into AC energy at specific frequency
(D) All the above

7. Harmonic Distortion is due to ______ [ ]

(A) Linear behavior of circuit elements (B) Non-Linear behavior of circuit elements
(C) Change in temperature (D) none of the above

8. During the retrace time the electrons forming the horizontal beam move from_____to_____.
[ ]
(A) left, right (B) right, left (C) bottom, top (D) top, bottom

9. A random noise generator produces a signal________ [ ]

(A) Whose amplitude varies randomly (B) Which has no periodic frequency
(C) Which has an unpredictable power spectrum (D) All the above.

10. Measuring range of a voltmeter can be extended by using ____ resistance. [ ]

(A) High shunt (B) High series (C) Low shunt (D) Low series

Cont…2
Code No: K1924 :2: Set No. 1

II Fill in the Blanks

11. The basic meter becomes an ac meter by adding _________.

12. In series type ohmmeter unknown resistor is connected in _______with meter.

13. The ratio of the change in output of instrument to a change in input or measured value is________

14. __________________analyzer is used for frequency measurement in megahertz range.

15. __________________ is widely used for generation of pulses.

16. __________________ circuit used to eliminate the problem of signal to be connected directly to
vertical plates.

17. The sensitivity of a voltmeter using 50µA meter is ___________

18. Vertical amplifier is the principle factor in determining the ______________________ of an

oscilloscope.

19. The deflection of the screen per unit deflection voltage is known as ______________

20. The no of time base circuits in dual trace CRO is_______

-oOo-
Code No: K1924 Set No. 2
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. II Sem., I Mid-Term Examinations, February – 2012
ELECTRONIC MEASUREMENTS AND INSTRUMENTATION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.

I Choose the correct alternative:

1. The purpose of synchronizing control in CRO is to [ ]

(A) Focus the spot on screen (B) Lock the display of signal
(C) Adjust amplitude of display (D) Control the intensity of spot

2. Errors due to human mistakes are ______ [ ]

(A) Gross errors (B) Systematic error (C) Instrumental errors (D) Environmental errors

3. In signal generator_______ [ ]
(A) Energy is created (B) Energy is generated
(C) Energy is converted from a DC source into AC energy at specific frequency
(D) All the above

4. Harmonic Distortion is due to ______ [ ]

(A) Linear behavior of circuit elements (B) Non-Linear behavior of circuit elements
(C) Change in temperature (D) none of the above

5. During the retrace time the electrons forming the horizontal beam move from_____to_____.
[ ]
(A) left, right (B) right, left (C) bottom, top (D) top, bottom

6. A random noise generator produces a signal________ [ ]

(A) Whose amplitude varies randomly (B) Which has no periodic frequency
(C) Which has an unpredictable power spectrum (D) All the above.

7. Measuring range of a voltmeter can be extended by using ____ resistance. [ ]

(A) High shunt (B) High series (C) Low shunt (D) Low series

8. Duty cycle of square wave is [ ]

(A) 25% (B) 75% (C) 50% (D) 100%

9. Frequency range of AF Signals [ ]

(A) 20Hz – 20KHz (B) 20KHz – 200KHz (C) 30KHz – 300KHz (D) 10KHz- 100KHz

10. Wave analyzer is used in _______measurements [ ]

(A) Electrical (B) Sound (C) Vibration (D) All the above

Cont…2
Code No: K1924 :2: Set No. 2

II Fill in the Blanks

11. __________________analyzer is used for frequency measurement in megahertz range.

12. __________________ is widely used for generation of pulses.

13. __________________ circuit used to eliminate the problem of signal to be connected directly to
vertical plates.

14. The sensitivity of a voltmeter using 50µA meter is ___________

15. Vertical amplifier is the principle factor in determining the ______________________ of an

oscilloscope.

16. The deflection of the screen per unit deflection voltage is known as ______________

17. The no of time base circuits in dual trace CRO is_______

18. The basic meter becomes an ac meter by adding _________.

19. In series type ohmmeter unknown resistor is connected in _______with meter.

20. The ratio of the change in output of instrument to a change in input or measured value is________

-oOo-
Code No: K1924 Set No. 3
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. II Sem., I Mid-Term Examinations, February – 2012
ELECTRONIC MEASUREMENTS AND INSTRUMENTATION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.

I Choose the correct alternative:

1. In signal generator_______ [ ]
(A) Energy is created (B) Energy is generated
(C) Energy is converted from a DC source into AC energy at specific frequency
(D) All the above

2. Harmonic Distortion is due to ______ [ ]

(A) Linear behavior of circuit elements (B) Non-Linear behavior of circuit elements
(C) Change in temperature (D) none of the above

3. During the retrace time the electrons forming the horizontal beam move from_____to_____.
[ ]
(A) left, right (B) right, left (C) bottom, top (D) top, bottom

4. A random noise generator produces a signal________ [ ]

(A) Whose amplitude varies randomly (B) Which has no periodic frequency
(C) Which has an unpredictable power spectrum (D) All the above.

5. Measuring range of a voltmeter can be extended by using ____ resistance. [ ]

(A) High shunt (B) High series (C) Low shunt (D) Low series

6. Duty cycle of square wave is [ ]

(A) 25% (B) 75% (C) 50% (D) 100%

7. Frequency range of AF Signals [ ]

(A) 20Hz – 20KHz (B) 20KHz – 200KHz (C) 30KHz – 300KHz (D) 10KHz- 100KHz

8. Wave analyzer is used in _______measurements [ ]

(A) Electrical (B) Sound (C) Vibration (D) All the above

9. The purpose of synchronizing control in CRO is to [ ]

(A) Focus the spot on screen (B) Lock the display of signal
(C) Adjust amplitude of display (D) Control the intensity of spot

10. Errors due to human mistakes are ______ [ ]

(A) Gross errors (B) Systematic error (C) Instrumental errors (D) Environmental errors

Cont…2
Code No: K1924 :2: Set No. 3

II Fill in the Blanks

11. __________________ circuit used to eliminate the problem of signal to be connected directly to
vertical plates.

12. The sensitivity of a voltmeter using 50µA meter is ___________

13. Vertical amplifier is the principle factor in determining the ______________________ of an

oscilloscope.

14. The deflection of the screen per unit deflection voltage is known as ______________

15. The no of time base circuits in dual trace CRO is_______

16. The basic meter becomes an ac meter by adding _________.

17. In series type ohmmeter unknown resistor is connected in _______with meter.

18. The ratio of the change in output of instrument to a change in input or measured value is________

19. __________________analyzer is used for frequency measurement in megahertz range.

20. __________________ is widely used for generation of pulses.

-oOo-
Code No: K1924 Set No. 4
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. II Sem., I Mid-Term Examinations, February – 2012
ELECTRONIC MEASUREMENTS AND INSTRUMENTATION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.

I Choose the correct alternative:

1. During the retrace time the electrons forming the horizontal beam move from_____to_____.
[ ]
(A) left, right (B) right, left (C) bottom, top (D) top, bottom

2. A random noise generator produces a signal________ [ ]

(A) Whose amplitude varies randomly (B) Which has no periodic frequency
(C) Which has an unpredictable power spectrum (D) All the above.

3. Measuring range of a voltmeter can be extended by using ____ resistance. [ ]

(A) High shunt (B) High series (C) Low shunt (D) Low series

4. Duty cycle of square wave is [ ]

(A) 25% (B) 75% (C) 50% (D) 100%

5. Frequency range of AF Signals [ ]

(A) 20Hz – 20KHz (B) 20KHz – 200KHz (C) 30KHz – 300KHz (D) 10KHz- 100KHz

6. Wave analyzer is used in _______measurements [ ]

(A) Electrical (B) Sound (C) Vibration (D) All the above

7. The purpose of synchronizing control in CRO is to [ ]

(A) Focus the spot on screen (B) Lock the display of signal
(C) Adjust amplitude of display (D) Control the intensity of spot

8. Errors due to human mistakes are ______ [ ]

(A) Gross errors (B) Systematic error (C) Instrumental errors (D) Environmental errors

9. In signal generator_______ [ ]
(A) Energy is created (B) Energy is generated
(C) Energy is converted from a DC source into AC energy at specific frequency
(D) All the above

10. Harmonic Distortion is due to ______ [ ]

(A) Linear behavior of circuit elements (B) Non-Linear behavior of circuit elements
(C) Change in temperature (D) none of the above

Cont…2
Code No: K1924 :2: Set No. 4

II Fill in the Blanks

11. Vertical amplifier is the principle factor in determining the ______________________ of an

oscilloscope.

12. The deflection of the screen per unit deflection voltage is known as ______________

13. The no of time base circuits in dual trace CRO is_______

14. The basic meter becomes an ac meter by adding _________.

15. In series type ohmmeter unknown resistor is connected in _______with meter.

16. The ratio of the change in output of instrument to a change in input or measured value is________

17. __________________analyzer is used for frequency measurement in megahertz range.

18. __________________ is widely used for generation of pulses.

19. __________________ circuit used to eliminate the problem of signal to be connected directly to
vertical plates.

20. The sensitivity of a voltmeter using 50µA meter is ___________

-oOo-