Double row deep

groove ball bearings

Bearing data – general ……………………………………………………………………… 392
Dimensions ………………………………………………………………………………… 392
Tolerances …………………………………………………………………………………… 392
Internal clearance …………………………………………………………………………… 392
Misalignment ………………………………………………………………………………… 392
Cages ………………………………………………………………………………………… 392
Minimum load ……………………………………………………………………………… 393
Axial load carrying capacity ……………………………………………………………… 393
Equivalent dynamic bearing load ………………………………………………………… 393
Equivalent static bearing load ……………………………………………………………… 393

Product table ………………………………………………………………………………… 394

391
Double row deep groove ball bearings

SKF double row deep groove ball bearings

(➔ fig 1 ) correspond in design to single row
Bearing data – general
deep groove ball bearings. They have deep Dimensions
uninterrupted raceways and high conformity The boundary dimensions of SKF double row
between the balls and raceways. They are deep groove ball bearings are in accordance
able to carry axial loads acting in both direc- with ISO 15:1998.
tions in addition to radial loads.
Double row deep groove ball bearings are Tolerances
very suitable for bearing arrangements SKF double row deep groove ball bearings
where the load carrying capacity of a single are produced to Normal tolerances. The
row bearing is inadequate. For the same values for tolerances correspond to ISO
outside and bore diameters, double row 492:2002 and can be found in table 3 on
bearings are slightly wider than single row page 125.
bearings but have considerably higher load
carrying capacity than single row bearings Internal clearance
in the 62 and 63 series. SKF double row deep groove ball bearings
have Normal radial internal clearance as
standard. The clearance limits are as speci-
Fig 1 fied in ISO 5753:1991 and can be found in
table 3 on page 297.

Misalignment
Misalignment of the inner ring relative to the
outer ring of a double row deep groove ball
bearing can only be accommodated by
force, which leads to increased ball loads
and cage forces and a reduction in bearing
service life. For this reason, the maximum
permissible angular misalignment is two
minutes of arc. Any misalignment of the
bearing rings will result in increased noise
during operation.

Cages
SKF double row deep groove ball bearings
are fitted with two glass fibre reinforced poly-
Fig 2 amide 6,6 cages (➔ fig 2 ), designation
suffix TN9.

Note:
Double row deep groove ball bearings with
polyamide 6,6 cages can be operated at
temperatures up to +120 °C. The lubricants
generally used for rolling bearings do not
have a detrimental effect on cage properties,
with the exception of a few synthetic oils and
greases with a synthetic oil base, and lubri-
cants containing a high proportion of EP
additives when used at high temperatures.
For detailed information regarding the
temperature resistance and the applicability
of cages, please refer to the section “Cage
materials”, starting on page 140.
392
Minimum load Equivalent dynamic bearing load
In order to obtain satisfactory operation, For dynamically loaded double row deep
double row deep groove ball bearings, like groove ball bearings
all ball and roller bearings, must be subjected
to a given minimum load, particularly if they P = Fr when Fa/Fr ≤ e
are to operate at high speeds or are subjected P = 0,56 Fr + YFa when Fa/Fr > e
to high accelerations or rapid changes in the
direction of load. Under such conditions the The factors e and Y depend on the relation-
inertia forces of the balls and cages, and the ship f0 Fa/C0, where f0 is a calculation factor
friction in the lubricant, can have a detrimental (➔ product table), Fa the axial component of
effect on the rolling conditions in the bearing the load and C0 the basic static load
arrangement and may cause damaging rating.
sliding movements to occur between the If the bearings are mounted with the usual
balls and raceways. fits (shaft tolerance j5 or k5, depending on the
The requisite minimum load to be applied shaft diameter, and housing bore tolerance
to double row deep groove ball bearings can J7) the values for e and Y given in table 1
be estimated using can be used to calculate the equivalent load.

Equivalent static bearing load

νn 2/3 2
Frm = kr
( )( )
1 000
dm
100
For statically loaded double row deep
groove ball bearings

where P0 = 0,6 Fr + 0,5 Fa

Frm = minimum radial load, kN
kr = minimum radial load factor If P0 < Fr, P0 = Fr should be used.
(➔ product table)
ν = oil viscosity at operating
temperature, mm2/s
n = rotational speed, r/min
dm = bearing mean diameter
= 0,5 (d + D), mm

When starting up at low temperatures or

when the lubricant is highly viscous, even
greater minimum loads may be required.
The weight of the components supported by
the bearing, together with external forces, Table 1
generally exceeds the requisite minimum Calculation factors for double row deep groove
load. If this is not the case, the double row ball bearings
deep groove ball bearings must be sub- f0 Fa/C0 e Y
jected to additional radial load.
0,172 0,19 2,30
Axial load carrying capacity 0,345 0,22 1,99
0,689 0,26 1,71
If double row deep groove ball bearings are
subjected to a purely axial load, this axial 1,03 0,28 1,55
1,38 0,30 1,45
load should generally not exceed the value 2,07 0,34 1,31
of 0,5 C0. Excessive axial loads can lead to 3,45 0,38 1,15
a substantial reduction in bearing life. 5,17 0,42 1,04
6,89 0,44 1,00

Intermediate values are obtained by linear interpolation

393
Double row deep groove ball bearings
d 10 – 65 mm

B
r2
r1

r1
r2

D D1 d d1

Principal Basic load ratings Fatigue Speed ratings Mass Designation

dimensions dynamic static load Reference Limiting
limit speed speed
d D B C C0 Pu

mm kN kN r/min kg –

10 30 14 9,23 5,2 0,224 40 000 22 000 0,049 4200 ATN9

12 32 14 10,6 6,2 0,26 36 000 20 000 0,053 4201 ATN9

37 17 13 7,8 0,325 34 000 18 000 0,092 4301 ATN9

15 35 14 11,9 7,5 0,32 32 000 17 000 0,059 4202 ATN9

42 17 14,8 9,5 0,405 28 000 15 000 0,120 4302 ATN9

17 40 16 14,8 9,5 0,405 28 000 15 000 0,090 4203 ATN9

47 19 19,5 13,2 0,56 24 000 13 000 0,16 4303 ATN9

20 47 18 17,8 12,5 0,53 24 000 13 000 0,14 4204 ATN9

52 21 23,4 16 0,68 22 000 12 000 0,21 4304 ATN9

25 52 18 19 14,6 0,62 20 000 11 000 0,16 4205 ATN9

62 24 31,9 22,4 0,95 18 000 10 000 0,34 4305 ATN9

30 62 20 26 20,8 0,88 17 000 9 500 0,26 4206 ATN9

72 27 41 30 1,27 16 000 8 500 0,50 4306 ATN9

35 72 23 35,1 28,5 1,2 15 000 8 000 0,40 4207 ATN9

80 31 50,7 38 1,63 14 000 7 500 0,69 4307 ATN9

40 80 23 37,1 32,5 1,37 13 000 7 000 0,50 4208 ATN9

90 33 55,9 45 1,9 12 000 6 700 0,95 4308 ATN9

45 85 23 39 36 1,53 12 000 6 700 0,54 4209 ATN9

100 36 68,9 56 2,4 11 000 6 000 1,25 4309 ATN9

50 90 23 41 40 1,7 11 000 6 000 0,58 4210 ATN9

110 40 81,9 69,5 2,9 10 000 5 300 1,70 4310 ATN9

55 100 25 44,9 44 1,9 10 000 5 600 0,80 4211 ATN9

120 43 97,5 83 3,45 9 000 5 000 2,15 4311 ATN9

60 110 28 57,2 55 2,36 9 500 5 300 1,10 4212 ATN9

130 46 112 98 4,15 8 500 4 500 2,65 4312 ATN9

65 120 31 67,6 67 2,8 8 500 4 800 1,45 4213 ATN9

140 48 121 106 4,5 8 000 4 300 3,25 4313 ATN9

394
 ra

ra

Da da

Dimensions Abutment and fillet Calculation

dimensions factors

d d1 D1 r1,2 da Da ra kr fo
~ ~ min min max max

mm mm –

10 16,7 23,3 0,6 14 26 0,6 0,05 12

12 18,3 25,7 0,6 16 28 0,6 0,05 12

20,5 28,5 1 17 32 1 0,06 12

15 21,5 29 0,6 19 31 0,6 0,05 13

24,5 32,5 1 20 37 1 0,06 13

17 24,3 32,7 0,6 21 36 0,6 0,05 13

28,7 38,3 1 22 42 1 0,06 13

20 29,7 38,3 1 25 42 1 0,05 14

31,8 42,2 1,1 26,5 45,5 1 0,06 13

25 34,2 42,8 1 30 47 1 0,05 14

37,3 49,7 1,1 31,5 55,5 1 0,06 13

30 40,9 51,1 1 35 57 1 0,05 14

43,9 58,1 1,1 36,5 65,5 1 0,06 13

35 47,5 59,5 1,1 41,5 65,5 1 0,05 14

49,5 65,4 1,5 43 72 1,5 0,06 13

40 54 66 1,1 46,5 73,5 1 0,05 15

56,9 73,1 1,5 48 82 1,5 0,06 14

45 59,5 71,5 1,1 51,5 78,5 1 0,05 15

63,5 81,5 1,5 53 92 1,5 0,06 14

50 65,5 77,5 1,1 56,5 83,5 1 0,05 15

70 90 2 59 101 2 0,06 14

55 71,2 83,8 1,5 63 92 1,5 0,05 16

76,5 98,5 2 64 111 2 0,06 14

60 75,6 90,4 1,5 68 102 1,5 0,05 15

83,1 107 2,1 71 119 2 0,06 14

65 82,9 99,1 1,5 73 112 1,5 0,05 15

89,6 115 2,1 76 129 2 0,06 14

395
Double row deep groove ball bearings
d 70 – 100 mm

B
r2
r1

r1
r2

D D1 d d1

Principal Basic load ratings Fatigue Speed ratings Mass Designation

dimensions dynamic static load Reference Limiting
limit speed speed
d D B C C0 Pu

mm kN kN r/min kg –

70 125 31 70,2 73,5 3,1 8 000 4 300 1,50 4214 ATN9

150 51 138 125 5 7 000 3 800 3,95 4314 ATN9

75 130 31 72,8 80 3,35 7 500 4 000 1,60 4215 ATN9

160 55 156 143 5,5 6 700 3 600 4,80 4315 ATN9

80 140 33 80,6 90 3,6 7 000 3 800 2,00 4216 ATN9

85 150 36 93,6 102 4 7 000 3 600 2,55 4217 ATN9

90 160 40 112 122 4,65 6 300 3 400 3,20 4218 ATN9

100 180 46 140 156 5,6 5 600 3 000 4,70 4220 ATN9

396
 ra

ra

Da da

Dimensions Abutment and fillet Calculation

dimensions factors

d d1 D1 r1,2 da Da ra kr fo
~ ~ min min max max

mm mm –

70 89,4 106 1,5 78 117 1,5 0,05 15

96,7 124 2,1 81 139 2 0,06 14

75 96,9 114 1,5 83 122 1,5 0,05 16

103 132 2,1 86 149 2 0,06 14

80 102 120 2 89 131 2 0,05 16

85 105 125 2 94 141 2 0,05 15

90 114 136 2 99 151 2 0,05 15

100 130 154 2,1 111 169 2 0,05 15

397