Tutorial – 1 (ALP 8085)

Microprocessor (BCT II / II)

1. Add two numbers located at 3030H and 4040H. Display sum on Port 1. If carry is generated,
display it on Port 2. Store sum on 5050H.

LDA 3030H
MOV B, A
LDA 4040H
ADD B
STA 5050H
OUT PORT 1
JNC L1
MVI A, 01H
OUT PORT 2
L1: HLT

2. Write an Assembly Language Program that retrieves a data located at 2050H and it displays,
if it is even and stores FFH on that location if it is odd.

LDA 2050H
ANI 01H
JNZ L1
LDA 2050H
OUT PORT 1
HLT
L1: MVI A, FFH
STA 2050H
HLT

3. Sixteen bytes of data are stored in memory location at 1050H to 105FH. Replace each data
byte by FF.

LXI H, 1050H
MVI C, 10H
L1: MVI M, FFH
INX H
DCR C
JNZ L1
HLT

Compiled By: Er. Hari Aryal email: [email protected] 1

4. Sixteen data are stored in memory location at 1050H to 105FH. Transfer the entire block of
data to new location starting at 1070H.

LXI H, 1050H
MVI C, 10H
LXI D, 1070H
L1: MOV A, M
STAX D
INX H
INX D
DCR C
JNZ L1
HLT

5. Six bytes are stored in memory locations starting at 2050H. Add all the data bytes, save any
carry generated while adding the data bytes. Display entire sum at two output ports and store
total carry in 2070H and sum in 2071H.

LXI H, 2050H
MVI C, 06H
MVI B, 00H
MVI D, 00H
L2: MOV A, M
ADD B
MOV B, A
JNC L1
INR D
L1: INX H
DCR C
JNZ L2
HLT

6. If the content of memory location 2050H is greater than or equal to 64H, display 0FH else
display FFH.

LDA 2050H
CPI 64H
JC L1
MOV A, 0FH
OUT PORT 1
HLT
L1: MOV A, FFH
OUT PORT 1
HLT

Compiled By: Er. Hari Aryal email: [email protected] 2

 7. We have a list of data stored at memory location starting at 2050H. The end of the data array
is indicated by data byte 00H. Add the set of readings. Display the sum at Port 1 and total
carry at Port 2.

LXI H, 2050H
MVI B, 00H
MVI C, 00H
L3: MOV A, M
CPI 00H
JZ L1
ADD C
JNZ L2
INR B
L2: MOV C, A
INX H
JMP L3
L1: MOV A, C
OUT PORT 1
MOV A, B
OUT PORT 2
HLT

8. There are two tables holding twenty data whose starting address is 3000H and 3020H
respectively. WAP to add the content of first table with the content of second table having
same array index. Store sum and carry into the third and fourth table indexing from 3040H
and 3060H respectively.

LXI B, 3000H MOV A, C

LXI H, 3020H CPI 14H
LXI D, 3040H JNZ NEXT
NEXT: LDAX B HLT
ADD M
STAX D
PUSH H
PUSH D
JNC L1
MVI E, 01H
JMP CSTORE
L1: MVI E, 00H
CSTORE: LXI H, 3060H
MOV A, L
ADD C
MOV L, A
MOV M, E
POP H
POP D
INX B
INX D
INX H

Compiled By: Er. Hari Aryal email: [email protected] 3

 9. For ten bytes data starting from 1120H, write a program to sort the reading in ascending and
in descending order. (Note : For descending, do self)

START: LXI H, 1120H

MVI D, 00H
MVI C, 0AH
L2: MOV A, M
INX H
CMP M
JC L1
MOV B, M
MOV M, A
DCX H
MOV M, B
INX H
MVI D, 01H
L1: DCR C
JNZ L2
MOV A, D
RRC
JC START
HLT

10. A set of ten readings is stored in memory location starting at 1160H. The readings are
expected to be positive (<127). WAP to
- Check each reading to determine whether it is positive or negative.
- Reject all negative readings.
- Add all positive readings & display sum in Port 1 and carry in Port 2.

MVI B, 00H
MVI C, 00H
MVI D, 0AH
LXI H, 1160H
L2: MOV A, M
RAL
JC NEGLECT
RAR
ADD B
JC L1
MOV B, A
L1: INR D
NEGLECT: INX H
DCR D
JNZ L2
MOV A, B
OUT PORT 1
MOV A, D
OUT PORT 2
HLT

Compiled By: Er. Hari Aryal email: [email protected] 4

11. A set of six data bytes is stored starting from memory location 2050H. The set includes some
blank spaces (bytes with zero values). WAP to eliminate the blanks from the block.

MVI C, 06H
LXI H, 2050H
LXI B, 2050H
L2: MOV A, M
CPI 00H
JZ L1
STAX B
INX B
L1: INX H
DCR C
JNZ L2
HLT

12. A set of eight data bytes (4 Pairs) are stored in memory locations starting from 1040H. WAP
to add two bytes at a time and store the sum in same memory location, sum replacing the first
byte and the carry replacing the second byte. If any pair does not generate a carry, the
memory location of the second byte should be cleared i.e. store 00H over there.

MVI C, 04H
LXI H, 1040H
L2: MOV A, M
INX H
ADD M
DCX H
MOV M, A
INX H
MVI M, 00H
JNC L1
MVI M, 01H
L1: INX H
DCR C
JNZ L2
HLT

Compiled By: Er. Hari Aryal email: [email protected] 5

 13. WAP to read BCD number stored at memory location 2020H and converts it into binary
equivalent and finally stores that binary pattern into memory location 2030H.
[Note: BCD number is the combination from 0 to 9]

MVI C, 0AH
LXI H, 2020H
MOV A, M
ANI F0H
RRC
RRC
RRC
RRC
MOV B, A
MOV A, 00H
L1: ADD B
DCR C
JNZ L1
MOV D, A
MOV A, M
ANI 0FH
ADD D
STA 2030H
HLT

14. A binary number (Suppose FF: 1111 11112) is stored in memory location 2020H. Convert the
number into BCD and store each BCD as two unpacked BCD digits in memory location from
2030H.
LXI SP, 2000H
LXI H, 2020H
MOV A, M
CALL PWRTEN
HLT
PWETEN: LXI H, 2030H
MVI B, 64H
CALL BINBCD
MOV M, D
INX H
MVI B, 0AH
CALL BINBCD
MOV M, D
INX H
MOV M, A
RET
BINBCD: MVI D, 00H
NEXT: INR D
SUB B
JNC NEXT
DCR D
ADD B
RET

Compiled By: Er. Hari Aryal email: [email protected] 6

15. An 8 bit binary number is stored in memory location 1120H. WAP to store ASCII codes of
these binary digits (0 to F) in location 1160H and 1161H.

LXI SP, 2000H CODE: CPI 0AH

LXI H, 1120H JC L1
LXI D, 1160H ADD 07H
MOV A, M L1: ADD 30H
ANI F0H RET
RRC
RRC
RRC
RRC
CALL CODE
STAX D
INX D
MOV A, M
ANI 0FH
CALL CODE
STAX D
HLT

16. WAP to convert ASCII at location 1040H to binary and store at location 1050H.

LXI SP, 2000H CODE: CPI 40H

LXI H, 1040H JC L1
LXI D, 1050H SUB 07H
MOV A, M L1: SUB 30H
ANI F0H RET
RRC
RRC
RRC
RRC
CALL CODE
STAX D
INX D
MOV A, M
ANI 0FH
CALL CODE
STAX D
HLT

Compiled By: Er. Hari Aryal email: [email protected] 7

17. A set of three packed BCD numbers are stored in memory locations starting at 1150H. The
seven segment codes of digits 0 to 9 for a common cathode LED are stored in memory
locations starting at 1170H and the output buffer memory is reserved at 1190H. WAP to
unpack the BCD number and select an appropriate seven segment code for each digit. The
codes should be stored in output buffer memory.

LXI SP, 2999H CODE: PUSH H

LXI H, 1150H LXI H, 1170H
MVI D, 03H ADD L
LXI B, 1190H MOV L, A
NEXT: MOV A, M MOV A, M
ANI F0H STAX B
RRC POP H
RRC RET
RRC
RRC
CALL CODE
INX B
MOV A, M
ANI 0FH
CALL CODE
INX B
INX H
DCR D
JNZ NEXT
HLT

18. A multiplicand is stored in memory location 1150H and a multiplier is stored in location
1151H. WAP to multiply these numbers and store result from 1160H.

MVI B, 08H
MVI D, 00H
LXI H, 1150H
MOV A, M
MOV E, A
LXI H, 1151H
MOV A, M
L2: RAR
JNC L1
LXI H, 0000H
DAD D
L1: XCHG
DAD H
XCHG
DCR B
LNZ L2
HLT

Compiled By: Er. Hari Aryal email: [email protected] 8

19. A set of ten packed BCD numbers is stored in the memory location starting at 1150H. WAP
to add these numbers in BCD. If carry is generated save it in register B and adjust it for BCD.
The final sum is less than 9999BCD.

LXI SP, 2000H

LXI H, 1150H
MVI C, 0AH
XRA A
MOV B, A
L1: CALL ADD
INX H
DCR C
JNZ L1
HLT

ADD: ADD M
DAA
RNC
MOV D, A
MOV A, B
ADI 01H
DAA
MOV B, A
MOV A, D
RET

20. A dividend is stored in memory location 2020H and a divisor is stored in 2021H. WAP to
divide these numbers and store quotient and remainder from 2040H.

MVI C, 00H
LXI H, 2021H
MOV A, M
MOV D, A
DCX H
MOV B, M
L2: MOV A, B
SUB D
JC L1
MOV B, A
INR C
JMP L2
L1: MOV L, C
MOV H, B
SHLD 2040H
HLT

Compiled By: Er. Hari Aryal email: [email protected] 9

21. Write a program for 8085 to convert and copy the ten lower case ASCII codes to upper case
from memory location 9050H to 90A0H if any, otherwise copy as they are. Assume there are
fifty codes in the source memory. [Note: ASCII code for A=65 … Z=90, a=97 … z=122].
[2063 Kartik]

LXI H, 9050H
LXI D, 90A0H
MVI C, 32H
L2: MOV A, M
CPI 60H
JC L1
SUI 20H
L1: STAX D
DCR C
JNZ L2
HLT

22. Write a program for 8085 to add ten 16-bit BCD numbers from location 4050H and store 24-
bit BCD result at the end of the ten given numbers. [2062 Chaitra]

LXI B, 4050H ; Starting location of the 16-bit BCD Numbers

LXI D, 0000H
LXI H, 0000H
MVI A, 00H

L2: LDAX B
ADD L
INX B
LDAX B
ADC H
JNC L1
INR E
L1: INX B
MOV A, C
CPI 0AH
JC L2

MOV A, L
STAX B
INX B
MOV A, H
STAX B
INX B
MOV A, E
STAX B
HLT

Compiled By: Er. Hari Aryal email: [email protected] 10

 23. Write an 8085 program to display the BCD digits from 0 to 9 the seven segments as in the
following diagram. Use the activating data bits same as the segment
number as in figure below. [2059 Shrawan]
0
5 1
6
4 2

3
LXI SP, 2999H
LXI H, 2050H
MOV M, 3FH
INX H
MOV M, 06H
INX H
MOV M, 5BH
INX H
MOV M, 4FH
INX H
MOV M, 66H
INX H
MOV M, 6DH
INX H
MOV M, 7DH
INX H
MOV M, 07H
INX H
MOV M, 7FH
INX H
MOV M, 6FH
LXI B, 2060H

LDAX B ; Where the BCD digit is located

ANI F0H
RRC
RRC
RRC
RRC
CALL CODE
OUT PORT 1
LDAX B
ANI 0FH
CALL CODE
OUT PORT 2
HLT
CODE: LXI H, 2050H
ADD L
MOV L, A
MOV A, M
RET

Compiled By: Er. Hari Aryal email: [email protected] 11

24. Write a program for 8085 to change the bit D5 of ten numbers stored at address 7600H if the
numbers are larger than or equal to 80H. [2061 Ashwin]

LXI H, 7600H
MVI C, 0AH
L2: MOV A, M
CPI 80H
JC L1
XRI 20H
MOV M, A
L1: INX H
DCR C
JNZ L2

25. Write a program for 8085 to find the smallest number among ten numbers stored at memory
location 4500H. [2060 Bhadra]

LXI H, 4500H
MVI C, 0AH
MOV A, M
L2: INX H
CMP M
JC L1
MOV B, A
MOV A, M
MOV M, B
L1: DCR C
JNZ L2
OUT PORT 1
HLT

Compiled By: Er. Hari Aryal email: [email protected] 12

26. Someone has damaged a program written at 4050H for 8085 microprocessor. The damaging
is done by changing the bit D7 and bit D5 of each byte. The size of the program is 100 bytes.
Now write a program for 8085 to correct this damaged program. [2060 Chaitra]

LXI H, 4050H
MVI C, 64H
L1: MOV A, M
ANI 80H ; 10000000 B
RRC
RRC
MOV B, A
MOV A, M
ANI 20H ; 00100000 B
RLC
RLC
MOV C, A
MOV A, M
ANI 5FH ; 01011111 B
ORA B
ORA C
STAX H
INX H
DCR C
JNZ L1
HLT

Compiled By: Er. Hari Aryal email: [email protected] 13

27. The temperature of two furnaces being monitored by a microprocessor based system. A set of
readings of the first furnace recorded by thermal sensor is stored at memory locations starting
at 4050H. Corresponding readings from the second furnace is stored at the memory location
starting at 4070H. Each reading from the first furnace is expected to be higher than the
corresponding reading from the second furnace. Among the eight bit data bit D7 is used to
test the validity of the data. Write an 8085 program to compare valid data from the two
tables, if data from first table is larger than the corresponding data from the second table
store 01H in the corresponding memory of the third location starting at 4090H and display
01H to indicate the normal operation else store FFH in the corresponding memory location
and display FFH in the port to indicate the emergency. When emergency condition is reached
stop the operation. [2060 Jestha]
LXI B, 4050H
LXI H, 4070H
LXI D, 4090H
L2: LDAX B
CMP M
JC L1
JZ L1
MVI A, 01H
STAX D
OUT PORT
INX B
IND H
INX D
JMP L2
L1: MVI A, FFH
STAX D
OUT PORT
HLT

28. Write a program to transfer eight-bit numbers from 9080H to 9090H if bit D5 is 1 and D3 is 0.
Otherwise transfer data by changing bit D2 and D6 from 1 to 0 or from 0 to 1. Assume there
are ten numbers. [2064 Shrawan]
LXI H, 9080H
LXI D, 9090H
MVI C, 0AH
L2: MOV A, M
ANI 28H
CPI 20H
JZ L1
MOV A, M
XRI 44H
MOV M, A
L1: MOV A, M
STAX D
INX H
INX D
DCR C
JNZ L2
HLT

Compiled By: Er. Hari Aryal email: [email protected] 14

29. There are two tables T1, T2 in memory having ten eight bit data in each. Write a program for
8085 to find the difference of the corresponding element of these two tables. Store the result of
each operation on the corresponding element of the third table. Remember that the result should
not be negative ; it should be |T1 – T2|. [2064 Poush]
LXI SP, 2999H
LXI H, 5000H ; TABLE T1
LXI D, 6000H ; TABLE T2
MVI C, 0AH ; COUNTER FOR 10 DATA
L1: LDAX D
MOV B, A
MOV A, M
CMP B
JNC L2
MOV A, B
MOV B, M
L2: SUB B
PUSH D
MVI D, 70H ; TABLE T3
STAX D
POP D
INX H
INX D
DCR C
JNZ L1
HLT
30. Write a program for 8085 to transfer data from a table to another if the number of ones in the
data is greater than four else store 00 in the next table. [2065 Kartik]
LXI H, 5000H ; SOURCE TABLE
LXI D, 6000H ; DESTINATION TABLE
ST: MVI C, 08H ; NO OF BITS
MVI B, 00H ; NO OF 1’S
MOV A, M
L1: RLC
JNC L2
INR B
L2: DCR C
JNZ L1
MOV A, B
CPI 04H
MVI A, 00H
JC L3
JZ L3
MOV A, M
L3: STAX D
INX H
INX D
MOV A, E
CPI 0AH ; SUPPOSE TABLE FOR 10 DATA
JNZ ST
HLT

Compiled By: Er. Hari Aryal email: [email protected] 15

31. Write an assembly language program to count no. of –ve element in a data block containing
16 bytes of data; store the count at the end of the block if the count is greater than 8 otherwise
stores 0. [2065 Chaitra]

Compiled By: Er. Hari Aryal email: [email protected] 16