Scribd
Upload
121 views1 page

M M P P For P M M P M M P P For P M M P: Angle Steel Member Capacity Based On AISC 360-10/16 Input Data & Design Summary

This document summarizes the design of an L8x6x1 angle steel member based on AISC 360-10/16 specifications. It is subjected to 10 kips of axial compression, 5 ft-kips of strong axis bending, and 6 ft-kips of weak axis bending. It also experiences 77 kips and 60 kips of strong and weak direction shear loads, respectively. Calculations are shown to check the combined compression and bending capacity, as well as the shear capacity, and it is determined that the design is adequate to resist all applied loads according to the specifications.

Uploaded by

AlaaBadwy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
121 views1 page

M M P P For P M M P M M P P For P M M P: Angle Steel Member Capacity Based On AISC 360-10/16 Input Data & Design Summary

This document summarizes the design of an L8x6x1 angle steel member based on AISC 360-10/16 specifications. It is subjected to 10 kips of axial compression, 5 ft-kips of strong axis bending, and 6 ft-kips of weak axis bending. It also experiences 77 kips and 60 kips of strong and weak direction shear loads, respectively. Calculations are shown to check the combined compression and bending capacity, as well as the shear capacity, and it is determined that the design is adequate to resist all applied loads according to the specifications.

Uploaded by

AlaaBadwy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 1

PROJECT : PAGE :

CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
Angle Steel Member Capacity Based on AISC 360-10/16

INPUT DATA & DESIGN SUMMARY


ANGLE SIZE L8X6X1
STEEL YIELD STRESS Fy = 36 ksi, (248 MPa)

AXIAL COMPRESSION FORCE P= 10 kips, (44 kN), ASD


STRONG GEOMETRIC AXIS EFFECTIVE LENGTH Lc,x = KLx = 20 ft, (6.10 m)
WEAK GEOMETRIC AXIS EFFECTIVE LENGTH Lc,y = KLy = 10 ft, (3.05 m)

STRONG GEOMETRIC AXIS BENDING MOMENT Mrx = 5 ft-kips, (7 kN-m), ASD


STRONG GEOMETRIC AXIS BENDING UNBRACED LENGTH Lbx = 20 ft, (6.10 m), (AISC 360 F2.2.c)
STRONG DIRECTION SHEAR LOAD, ASD Vstrong = 77 kips, (343 kN)

WEAK GEOMETRIC AXIS BENDING MOMENT Mry = 6 ft-kips, (8 kN-m), ASD


WEAK GEOMETRIC AXIS BENDING UNBRACED LENGTH Lby = 10 ft, (3.05 m)
WEAK DIRECTION SHEAR LOAD, ASD Vweak = 60 kips, (267 kN)

THE DESIGN IS ADEQUATE.

ANALYSIS
CHECK COMBINED COMPRESSION AND BENDING CAPACITY (AISC 360 H1)

 P r 8  M r ,max M r ,min  P r  0.2


     , for
 Pc 9  M c ,max M c,min  Pc 0.91 < 1.0 [Satisfactory]
 
 P r  M r ,max M r ,min  P r  0.2
     , for
2 P
 c  c,maxM M c,min  P c
Where Pc = Pn / Wc = 136 / 1.67 = 81.28 kips, (AISC 360 Chapter E5)
> Pr [Satisfactory]
Mr,max = 7.78 ft-kips or 0.71 ft-kips ,(major principal axis bending)
Mr,min = 0.71 ft-kips or 7.78 ft-kips ,(minor principal axis bending)
Mc,max = Mn / Wb = 42.24 / 1.67 = 25.29 ft-kips, (smaller equal-leg section used, AISC 360 Chapter F10-2)
> Mr,max [Satisfactory]
Mc,min = Mn / Wb = 15.89 / 1.67 = 9.51 ft-kips
> Mr,min [Satisfactory]

CHECK SHEAR CAPACITY (AISC 360 G2)


Vn,strong / Wv = 172.8 / 1.67 = 103.5 kips > Vstrong = 77.0 kips [Satisfactory]

Vn,weak / Wv = 129.6 / 1.67 = 77.6 kips > Vweak = 60.0 kips [Satisfactory]

You might also like