TM 11 5855 262 10 2 NVG Anpvs 7b

ARMY TM 11-5855-262-10-2
MARINE CORPS TM 09500A-10/1A

NAVSEA SW215-AT-OMI-010
AIR FORCE TO 12S10-2PVS7-11
Equipment Description
OPERATOR'S Page 1-9
MANUAL
PMCS Table
NIGHT VISION
GOGGLES (NVG) Page 2-6
AN/PVS-7B Image Intensifier

(NSN 5855-01-228-0937) Inspection Criteria
(EIC: IPS)
Page 2-27
AND
AN/PVS-7D
(NSN 5855-01-422-5413) Operation
(EIC: N/A) Page 2-66
DISTRIBUTION STATEMENT C - Distribution authorized to U.S. Government

agencies and their contractors. This publication is required for administrative and
operational purposes, as determined on 16 August 1991. Other requests for this
document shall be referred to either: Commander, U.S. Army Communications-
Electronics Command and Fort Monmouth, ATTN: AMSEL-LC-LEO-E-ED-P, Fort
Monmouth, NJ 07703-5000; Commander, Warner-Robins Air Logistics Center/LYE,
380 2nd Street, Suite 104, Robins AFB, GA 31098-1638; Commandant of the Marine
Corps (ARD), Washington, DC 20380-0001; or Commanding Officer, Naval Ship
Weapons Engineering Station, (Code L700), Port Hueneme, CA 93043-5007.
DESTRUCTION NOTICE - For unclassified, limited documents, destroy by any

method that will prevent disclosure of contents or reconstruction of the document.
DEPARTMENTS OF THE ARMY, HEADQUARTERS,

MARINE CORPS, THE NAVY, AND THE AIR FORCE
1 June 2000
PCN 184 095003 00
a
WARNING
• Do not carry batteries in pockets containing

metal objects such as coins, keys, etc. Metal
objects can cause the batteries to short
circuit and become very hot.
WARNING
Toxic Material
The image intensifier’s phosphor screen contains

toxic materials.
• If an image intensifier breaks, be extremely
careful to avoid inhaling the phosphor screen
material. Do not allow the material to come
in contact with the mouth or open wounds on
the skin.
• If the phosphor screen material contacts your

skin, wash it off immediately with soap and
water.
• If you inhale/swallow any phosphor screen

material, drink a lot of water, induce vomiting,
and seek medical attention as soon as
possible.
WARNING
The compass illuminator can be seen by other

night vision users.
a
WARNING
It is critical that the goggles be turned off manually

before placing them in the flipped up position in
order to avoid detection by the enemy.
WARNING
When installing the headmount over the protective

mask, be careful not to break the protective mask
seal around your face.
WARNING
The IR source is a light that is invisible to the

unaided eye for use during conditions of extreme
darkness. However, the light from the IR source
can be detected by the enemy using night vision
devices.
WARNING
Do not use contaminated eyecups. They must be

replaced.
b
WARNING
EQUIPMENT LIMITATIONS
To avoid physical and equipment damage when using the Night

Vision Goggles (NVG) carefully read and understand the following
safety precautions.
• The NVG requires some night light

(moonlight, starlight, etc.) to operate. The
level of performance depends upon the level
of light.
• Night light is reduced by passing cloud cover,

while operating under trees, in building
shadows, etc.
• The NVG is less effective viewing into

shadows and other darkened areas.
• The NVG is less effective through rain, fog,

sleet, snow or smoke.
• The NVG will not “see” through dense smoke.
• Adjust vehicular speed to prevent overdriving

the range of view when conditions of possible
reduction or loss of vision exist.
FIRST AID
For first aid or artificial respiration, see FM 21-11, First Aid for
Soldiers.
c/d blank
TECHNICAL MANUAL DEPARTMENTS OF THE ARMY,
No. 11-5855-262-10-2* HEADQUARTERS,
TECHNICAL MANUAL MARINE CORPS
No. 09500A-10/1A THE NAVY,
TECHNICAL MANUAL AND THE AIR FORCE,
No. SW215-AT-OMI-010 Washington, DC
TECHNICAL ORDER 1 June 2000
No. 12S10-2PVS7-11
OPERATOR’S MANUAL
NIGHT VISION GOGGLES (NVG)
AN/PVS-7B (NSN 5855-01-228-0937) (EIC: IPS)
AND
AN/PVS-7D (NSN 5855-01-422-5413) (EIC: N/A)
REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS

You can help improve this manual. If you find any mistakes or if you know of
a way to improve the procedures, please let us know. Mail your letter, DA
Form 2028 (Recommended Changes to Publications and Blank Forms),
direct to: Commander, U.S. Army Communications-Electronics Command
and Fort Monmouth, ATTN: AMSEL-LEO-D-CS-CFO, Fort Monmouth, New
Jersey 07703-5000. The Fax number is 732-532-1413, DSN 992-1413.
You may also email your recommendations to AMSEL-LC-LEO-PUBS-
[email protected]. Send your AFTO Form 22 (Technical
Order System Publication Improvement Report and Reply) in accordance
with paragraph 6-5, Section VI, TO 00-5-1. Forward to Warner-Robins Air
Logistics Center/LYGO, 380 2nd Street, Suite 104, Robins AFB, GA 31098-
1638. Send your NAVMC 10772 to: Commander, Marine Corps Logistics
Base (Code 826), 814 Radford Blvd. Albany, GA 31704-5000. Marine
Corps units should also respond to MARCORPSYSCOM ATTN: (CBG) with
a copy of the NAVMC 10772 or via Naval message. Send your NAVSEA
Form 9086/10 to: Commanding Officer, Naval Ship Weapon Systems
Engineering Station (Code 5H00), Port Hueneme, CA 93043-5007. A reply
will be furnished to you.
*This manual supersedes TM 11-5855-262-10-2 dated 1 December 1997

and all changes thereto.
i/ii blank
TABLE OF CONTENTS
Para. No. Title Page
CHAPTER 1 INTRODUCTION .......................................... 1-1
Section I General Information ......................................... 1-1

1-1 Scope .............................................................. 1-1
1-2 Maintenance Forms and Procedures ............... 1-1
1-3 Corrosion Prevention and Control (CPC) ......... 1-2
1-4 Destruction of Electronic Materiel to Prevent
Enemy Use...................................................... 1-2
1-5 Reporting Equipment Improvement
Recommendations (EIR).................................. 1-3
1-6 Warranty Information ....................................... 1-3
1-7 Nomenclature Cross-Reference List ................ 1-3
1-8 List of Abbreviations and Acronyms ................. 1-5
1-9 Glossary .......................................................... 1-6
Section II Equipment Description .................................... 1-9

1-10 Equipment Characteristics, Capabilities and
Features .......................................................... 1-9
1-11 Location and Description of
Major Components .......................................... 1-10
1-12 Difference Between Models ............................. 1-18
1-13 Equipment Data............................................... 1-18
Section III Principles of Operation .................................... 1-21

1-14 Mechanical Functions ...................................... 1-21
1-15 Optical Functions............................................. 1-22
1-16 Electronic Circuit Function ............................... 1-23
iii
TABLE OF CONTENTS - Continued.
CHAPTER 2 .................................................................... 2-1
Section I Description and Use of Operator’s

Controls and Indicators .................................... 2-1
2-1 Operator Controls and Indicators ..................... 2-1
Section II Prevention Maintenance Checks

and Services (PMCS) ...................................... 2-6
2-2 Preventive Maintenance Checks and
Services Table ................................................. 2-6
2-3 Resolution Check Using the
TS-4348/UV Test Set....................................... 2-22
2-4 Inspection Criteria for Proper Image
Intensifier Operation.........................................2-26
Section III Assembly and Preparation for Use................... 2-33

2-5 Unpacking........................................................2-33
2-6 Installation of Batteries..................................... 2-34
2-7 Installation of Eyecups ..................................... 2-36
2-8 Installation of Demist Shields ...........................2-37
2-9 Installation of Sacrificial Window ...................... 2-37
2-10 Installation of Compass.................................... 2-38
2-11 Installation of LIF .............................................2-40
2-12 Installation of IR Spot/Flood Lens .................... 2-42
2-13 Installation and Adjustment of
Headmount ......................................................2-43
iv
2-14 Installation of Headmount with

Protective Mask ............................................... 2-46
2-15 Installation of Headmount
with Helmet...................................................... 2-46
2-16 Installation of Original Helmet Mount
to Helmet ......................................................... 2-47
2-17 Installation of New Helmet Mount
to Helmet ......................................................... 2-51
2-18 Installation of New Helmet Mount
with New Nape Strap to Helmet ....................... 2-54
2-19 Installation of the AN/PVS-7D Helmet Mount
to Helmet ......................................................... 2-57
2-20 Installation of 3X Magnifier............................... 2-63
Section IV Operating Procedures .................................... 2-65

2-21 Head Mounted Operations............................... 2-65
2-22 Helmet Mounted Operations ............................ 2-68
2-23 Hand-Held Operation....................................... 2-73
2-24 Operation with Compass.................................. 2-74
2-25 IR Source Operations ...................................... 2-77
2-26 Operation with 3X Magnifier............................. 2-78
2-27 Preparation for Storage.................................... 2-79
v
Section V Operation Under Unusual Conditions............... 2-81

2-28 Operation in Dusty or Sandy Areas.................. 2-81
2-29 Operation in Rainy or Humid Conditions .......... 2-81
2-30 Operation in Salt Water Areas ......................... 2-82
2-31 Operation in NBC Environments ...................... 2-82
2-32 Operation in Laser Threat Environments.......... 2-83
CHAPTER 3 MAINTENANCE INSTRUCTIONS............... 3-1
Section I Lubrication Instructions .................................... 3-1
Section II Troubleshooting Procedures ............................ 3-1

3-1 Troubleshooting ............................................... 3-1
Section III Operator’s Maintenance Procedures................ 3-7

3-2 Cleaning the NVG............................................ 3-7
3-3 Headmount Maintenance ................................. 3-7
3-4 Neck Cord Maintenance .................................. 3-10
APPENDIX A References .................................... A-1
APPENDIX B Components of End Item (COEI)

and Basic Issue Items (BII) List ..... B-1
APPENDIX C Additional Authorization List

(AAL) ............................................. C-1
APPENDIX D Expendable and Durable Items

List ................................................. D-1
ALPHABETICAL INDEX .................................................... Index-1
vi
HOW TO USE THIS MANUAL
• Usage
You must familiarize yourself with the entire manual before

operating the equipment. Read and follow all warning notices.
• Manual Overview
The table of contents includes the paragraph number, title, and

page number for each chapter. An index provides additional
references to the subject contents.
• Special Features
A locator is provided on the right-hand border of the front cover.

This gives the location of the information most frequently used. To
find the topic OPERATION, open the manual to the correct page
by using the black tab on the side of the manual that lines up with
the topic OPERATION.
vii/viii blank
CHAPTER 1
INTRODUCTION
Section I. General Information
1-1 SCOPE
This manual provides operation and maintenance instructions for

the Night Vision Goggles, AN/PVS-7B and AN/PVS-7D, hereinafter
referred to as the NVG. The NVG is a self-contained night vision
device that enables improved night vision using ambient light from
the night sky (moon, stars, skyglow, etc.).
1-2 MAINTENANCE FORMS AND PROCEDURES
Department of the Army and procedures used for equipment

maintenance will be those prescribed by DA Pam 738-750, as
contained in Maintenance Management Update.
Refer to the latest issue of DA Pam 25-30 to determine whether

there are new editions, changes or additional publications
pertaining to the equipment.
Marine Corps personnel refer to the on-line Marine Corp

Publications Distribution System (MCPDS).
Marine Corps Ground Equipment Record Procedures. Marine

Corps personnel refer to TM 4700-15/1 for disposition of forms and
records required for Marine Corps equipment.
1-1
1-3 CORROSION PREVENTION AND CONTROL (CPC)
Corrosion prevention and control of Army materiel is a continuing

concern. It is important that any corrosion problems with this
equipment be reported so that the problem can be corrected and
improvements made to prevent the problem in future equipment.
While corrosion is typically associated with rusting metal, it can

also include deterioration of other materials such as contacts,
injection-molded plastic, and foam inserts in the case. Unusual
cracking, softening, swelling, or breaking of these other materials
may be a corrosion problem.
If a corrosion problem is identified, report it using Standard Form

368, Product Quality Deficiency Report. Use keywords such as
“corrosion”, “rust”, “deterioration”, or “cracking” to ensure that the
information is identified as a CPC problem. Submit the form to the
address in DA Pam 738-750.
1-4 DESTRUCTION OF ELECTRONIC MATERIEL TO

PREVENT ENEMY USE
For procedures to destroy this equipment to prevent its use by the

enemy, refer to TM 750-244-2, Procedures for Destruction of
Electronic Materiel to Prevent Enemy Use (Electronics Command).
Marine users, render the NVG inoperable by smashing, scattering
or burying disassembled pieces, burning, or destroying by
weapons fire.
1-2
1-5 REPORTING EQUIPMENT IMPROVEMENT
RECOMMENDATIONS (EIR)
If your equipment needs improvement, let us know. Send us an

EIR. You, the user, are the only one who can tell us what you
don’t like about the design. Put it on an SF 368 Product Quality
Deficiency Report. Mail it to Commander, U.S. Army
Communications-Electronics Command and Fort Monmouth,
ATTN: AMSEL-LC-LEO-D-CS-CFO, Fort Monmouth, New Jersey
07703-5000. We’ll send you a reply.
Marine Corps personnel are encouraged to submit SF 368 in

accordance with MCO 4855.10 (Quality Deficiency Report).
1-6 WARRANTY INFORMATION
Some NVG systems are under warranty. The warranty expiration

date label is affixed to the front (objective lens end) of the goggle
on the opposite side from the power switch. Report all defects in
material or workmanship to your maintainer, who will take the
appropriate action.
1-7 NOMENCLATURE CROSS-REFERENCE LIST
Table 1-1 provides a cross reference of common names and

official terms. Except in the Appendices, the common names will
be used. The official names are used in the Appendices because
they reflect the provisioning nomenclature.
1-3
Table 1-1. Nomenclature Cross-Reference List.
COMMON NAME OFFICIAL NOMENCLATURE
Batteries Battery, Nonrechargeable

Battery Cartridge Cover, Battery Retainer
Carrying Case Case, Infrared Equipment
Carrying Case Strap Strapping
Compass Compass Assembly
Demist Shield Demist Shield Assy
Eyeguard Eyeguard, Optical
Goggles Goggle Assembly
Headmount Headset Assembly
Helmet Mount Mount, Viewer
IR Spot/Flood Lens Lens Assembly, Focus
LIF Filter, Light Interference
Medium Browpad Browpad Assy, Medium
Neck Cord Cord, Fibrous
Objective Lens Cap Cap, Protective, Dust
Sacrificial Window Window, Sacrificial
Shipping and Storage Case Case, Shipping/Storage
Tethering Cord Clip, Retaining
Thick Browpad Browpad Assy, Thick
Thin Browpad Browpad Assy, Thin
3X Magnifier Magnifier Lens Assembly
1-4
1-8 LIST OF ABBREVIATIONS AND ACRONYMS
AAL Additional Authorization List
BII Basic Issue Items
CAGEC Commercial and Government Entity Code
cm Centimeters
COEI Components of End Item
CPC Corrosion Prevention and Control
CTA Common Table of Allowances
DA Department of the Army
EIC End Item Code
EIR Equipment Improvement Recommendations
FM Field Manual
Hrs Hours
IR Infrared
JTA Joint Table of Allowances
lbs Pounds
lp/mm Line pairs per millimeter
LED Light Emitting Diode
LIF Light Interference Filter
MCPDS Marine Corp Publication Distribution System
MIP Maintenance Index Page
MRC Maintenance Requirement Cards
MTOE Modified Table of Organization and Equipment
N/A Not Applicable
NBC Nuclear, Biological, and Chemical
NSN National Stock Number
NVG Night Vision Goggles
Pam Pamphlet
PASGT Personal Armor System Ground Troops
PMCS Preventive Maintenance Checks and Services
Qty Quantity
Recm Recommended
Rqr Required
SAMS Standard Army Maintenance System
SF Standard Form
TAMMS The Army Maintenance Management System
TDA Table of Distribution and Allowances
1-5
TM Technical Manual
TOE Table of Organization and Equipment
U/M Unit of Measure
ULLS Unit Level Logistics System
Vdc Volts, direct current
1-9 GLOSSARY
BLACK SPOTS. These are cosmetic blemishes in the image
intensifier or dirt or debris between the lenses.
BRIGHT SPOTS. These can be defects in the image area caused

by a flaw in the film on the microchannel plate. A bright spot is a
small, nonuniform, bright area that may flicker or appear constant.
Bright spots usually go away when the light is blocked out and are
cosmetic blemishes that are signal induced.
BROWPADS. Three hook-and-pile browpads are provided to

adjust the headmount to fit different head sizes. The thin browpad
(large head) comes attached to the headmount and the thick (small
head) or medium browpads are stored in the carrying case.
CAUTION. Condition, practices, or procedures that must be

observed to avoid damage to equipment, destruction of equipment,
or a long-term health hazard.
CHICKEN WIRE. An irregular pattern of dark thin lines in the

field-of-view either throughout the image area or in parts of the
image area. Under the worst case condition, these lines will form
hexagonal or square-wave shaped lines.
DARK (OR DARK AREA). A place in which there is very little

light. It does not mean total darkness. Generally, this means
conditions similar to a quarter-moon or starlit night.
DARK-ADAPTED. Having ones eyes adjusted to the goggles’

output under low light conditions. This takes at least 10 minutes.
However, if you have just been exposed to bright sunlight, dark
adaptation will take longer.
1-6
DIOPTER. A unit of measure used to define eye correction.
Adjustments to the diopter adjustment will provide a clearer image
in each eye.
EDGE GLOW. This is a defect in the image area of the NVG.

This defect is a bright area (sometimes sparkling) in the outer
portion of the viewing area.
EMISSION POINT. A steady or fluctuating pinpoint of bright light

in the image area and does not go away when all light is blocked
from the objective lens of the goggle. The position of an emission
point within the image area of the goggle does not move. An
emission point should not be confused with a point light source in
the distance.
FIXED-PATTERN NOISE. This is a cosmetic blemish in the

image area characterized by a faint hexagonal (honeycomb)
pattern throughout the viewing area that most often occurs at
highlight levels when viewing very bright lights. Fixed-pattern
noise is inherent in the structure of the fiber optics and can be
seen in every image intensifier if the light level is high enough.
FLASHING. This is a defect in the image area of the NVG. The

image appears to flicker or flash.
FLICKERING. See “flashing”.
HIGHLIGHT CUTOFF. The goggles will automatically cut off

after 70 ±30 seconds of operation in daylight or bright roomlight.
Individual bright lights (headlights, flashlights, or other
concentrated light sources) will not actuate the highlight cutoff
function unless focused directly on the highlight detector located
on the front of the goggles.
IMAGE INTENSIFIER. An electro-optical device that detects and

amplifies ambient light to produce a visual image.
1-7
INFINITY FOCUS. Adjustment of the objective lens so that a
distant object, such as a star or the point light on a distant tower,
forms the sharpest image.
INTERMITTENT OPERATION. This is a defect in the image area

of the NVG. See “flashing”.
IR SOURCE. This is an IR Light Emitting Diode (LED). When

turned on, the IR source provides additional illumination to
enhance existing light conditions. Used only for performing nearby
tasks.
LIF. This is a light protection filter for the objective lens. Use of
this filter will result in a slight reduction in system gain.
MICROCHANNEL PLATE. A current-multiplying optical disk that

intensifies the electron image produced by the photocathode.
NOTE. Essential information of special importance, interest, or

aid in job performance.
PHOTOCATHODE. The input of an image intensifier that absorbs

light energy and in turn releases electrical energy in the form of an
electron image.
SCINTILLATION. A faint, random, sparkling effect throughout the

image area. Scintillation is a normal characteristic of the image
intensifier and should not be confused with emission points.
Scintillation is more pronounced under low light conditions. Also
called “video noise”.
SHADING. The viewed image should be a full circle. If shading is

present, you will not see a fully circular image. Shading is
indicative of a dying photocathode and is caused by a defective
vacuum seal of the image intensifier. Shading is very dark and you
cannot see an image through it.
WARNING. Conditions, practices, or procedures that must be

observed to avoid personal injury or loss of life.
1-8
Section II. Equipment Description
1-10 EQUIPMENT CHARACTERISTICS, CAPABILITIES

AND FEATURES
WARNING
EQUIPMENT LIMITATIONS
To avoid physical and equipment damage when using the NVG,

carefully read and understand the following safety precautions.
• The NVG requires some night light

(moonlight, starlight, etc.) to operate. The
level of performance depends upon the level
of light.
• Night light is reduced by passing cloud cover,

while operating under trees, in building
shadows, etc.
• The NVG is less effective viewing into

shadows and other darkened areas.
• The NVG is less effective through rain, fog,

sleet, snow or smoke.
• The NVG will not “see” through dense smoke.
• Adjust vehicular speed to prevent overdriving

the range of view when conditions of possible
reduction or loss of vision exist.
1-9
CAUTION
• The NVG is a precision optical instrument

and must be handled carefully at all times to
prevent damage.
• Be careful when leaving the helmet mount in

the flipped up position or removing the helmet
mount from the helmet, damage can result.
NOTE
When utilizing the NVG for driving purposes, the

NVG may not be used in the hand-held mode.
The NVG must be worn in the headmounted or
helmet mounted position.
The NVG is a hand-held, headmounted or helmet mounted night

vision system that enables walking, driving, weapon firing, short-
range surveillance, map reading, vehicle maintenance, and
administering first aid in both moonlight and starlight. The system
allows for vertical adjustment (by using head straps), fore-and-aft
adjustment, objective focus, eyepiece focus, and eye span
distance adjustment. The NVG is also equipped with an IR source
and a low-battery indicator. The NVG will not be turned off
automatically when disconnected from the headmount or helmet
mount. Turn off the NVG by the power switch. There is also a
highlight cutoff feature that cuts off power to the NVG when it is
exposed to high levels of light for 70 ±30 seconds.
1-11 LOCATION AND DESCRIPTION OF MAJOR

COMPONENTS
The NVG includes items shown in Figure 1-1. The Major
components are the headmount (Figure 1-1), the goggles, the
carrying case, and the shipping and storage case.
1-10
Figure 1-1. Night Vision Goggles (NVG), AN/PVS-7B
and AN/PVS-7D (Sheet 1 of 3).
1-11
1-12
1-13
a. Goggles.
The goggles (see Figure 1-2 for breakdown) consist of four primary
subassemblies: an objective lens, a wired housing, an image
intensifier (not shown), and a rear cover. The wired housing
contains a built-in battery compartment, attached battery cap, and
the power switch. The goggles also use the accessories listed
below:
Figure 1-2. Goggles

and Accessory Items.
1-14
Demist Shields – The two demist shields (Figure 1-2) are used to
prevent the eyepiece lenses from becoming fogged.
LIF – The LIF (Figure 1-2) is to be used at all times. For replacing
the filter the container is also the wrench. The container/wrench is
used to remove and replace the LIF from the objective lens.
Sacrificial Window – A replaceable sacrificial window (Figure 1-2)

is supplied to protect the objective lens during operation in adverse
conditions.
IR Spot/Flood Lens – This additional authorized item (AAL) (Figure

1-2) focuses the IR light for a narrow beam (spot) or wide angle
(flood) beam illumination.
Compass – This item (Figure 1-2) enables operator to see azimuth

readings in the goggles viewing area. It is an AAL item for the
AN/PVS-7B. It is a Component of End Item (COEI) of the
AN/PVS-7D.
Tethering Cord – This AAL item (Figure 1-2) enables the user to
attach the compass or 3X magnifier to his/herself to guard against
dropping or losing these items.
3X Magnifier – (AAL Item) The 3X magnifier (Figure 1-2) is a lens

assembly, which can be added to the objective lens to extend the
operator’s observation ranges.
b. Headmount. The adjustable cushioned headmount (Figure

1-1) secures the goggles to the operator’s head for night viewing
and provides freehand support for use with a weapon, protective
mask or other purposes. The thin browpad used for large heads,
comes attached to the headmount; the thick and medium
browpads, used for smaller heads, are stored in the carrying case.
1-15
c. Helmet Mount. The helmet mount secures the goggles to
the PASGT helmet, allowing freehand support for use with
weapon, protective mask or other purposes. The new helmet
mount is made of a ruggedized metal. The old one is made of
plastic. The metal helmet mount is the only replacement available.
Figure 1-3 shows the various versions of the helmet mounts.
1-16
Figure 1-3. Helmet Mounts.
NOTE
The Helmet Mounts can be used with any NVG.
1-17
d. Carrying Case. The carrying case is provided for
transportation and protection of the goggles, headmount, batteries
and accessories. Two slide keeps are provided for belt attachment
and three D-rings for shoulder and leg strap attachment. A
carrying case strap is also provided which can be attached to the
two D-rings on the back of the carrying case. The old case (Figure
1-1) has a hook and pile closure, and the new case (Figure 1-1)
has a zipper closure.
e. Shipping and Storage Case. The NVG is supplied in a

shipping and storage case (Figure 1-1).
1-12 DIFFERENCE BETWEEN MODELS
The most significant difference between the AN/PVS-7B and

AN/PVS-7D models is the image intensifier. The AN/PVS-7B used
the MX-10130C tube and the AN/PVS-7D uses the MX-10130D
tube with a minimum resolution of 64 lp/mm. Use only the MX-
10130D in both models.
1-13 EQUIPMENT DATA
The following tables provide information pertaining to the

operational, electrical, mechanical, optical, and environmental
characteristics for the NVG.
1-18
Table 1-2. Operator Adjustment Limits.
ITEM LIMITS
Interpupillary Distance 55 to 71 mm
Diopter Focus +2 to –6 diopters
Objective Focus 25 cm to infinity
Table 1-3. Electrical Data.
ITEM DATA
Power Source Battery (3 Vdc max)

Battery Requirements 2 AA Alkaline or
2 AA 1.5 Vdc Lithium L91 or
1 Lithium (BA-5567/U)
Table 1-4. Mechanical Data.
ITEM DATA
Shipping and Storage Case Size: Approx. 17” x 12” x 7”

Weight: 6.7 lbs.
Carrying Case (Canvas) Size: Approx. 14” x 8”
Goggles (see Note) Weight: 1.5 lbs.
NOTE: Weight of the goggles does not include accessories.
1-19
Table 1-5. Optical Data.
ITEM DATA
Magnification 1.0X
Field-of-View 40°
Diopter Adjustment +2 to –6 diopters
Focus Range 20 cm (7.9”) to infinity
Table 1-6. Environmental Data.
ITEM DATA
Goggles Operating
Temperature -60°F to +113°F
Goggles Storage
Temperature -60°F to +160°F
Illumination Required Overcast starlight to moonlight
1-20
Section III. Principles of Operation
1-14 MECHANICAL FUNCTIONS
The mechanical functions of the NVG allow for differences in the

physical features of individual operators and provide for operating
the NVG. These functions include the power switch, interpupillary
adjustment, eye relief adjustment, diopter adjustment, IR spot/flood
lens and objective focus. The mechanical controls are identified in
Figure 1-4.
Figure 1-4. Mechanical Controls.
1-21
1-15 OPTICAL FUNCTIONS
The optical functions are provided by an objective lens, an image

intensifier, a collimator and two eyepiece lenses (Figure 1-5). The
objective lens collects light reflected from the night scene by the
moon, stars, or night sky, inverts the image and focuses that image
on the image intensifier. The image intensifier converts the
captured light into a visible image, which is then split and
reinverted by the collimator and transmitted to the eyepiece lenses
for viewing.
Figure 1-5. Optical Function Diagram.
1-22
1-16 ELECTRONIC CIRCUIT FUNCTION
The electronic circuit (Figure 1-6) regulates the direct current

voltage from the batteries to the image intensifier and IR source as
required. It also monitors the output voltage of the batteries and
turns on a low-battery indicator in the right eyepiece when the
battery life remaining is approximately 30 minutes (2.4 Vdc).
Figure 1-6. Electrical Function Diagram.
a. Power Source. The electronic circuit is powered by

replaceable batteries – either a 3.0-volt lithium battery (BA-5567
/U), two AA 1.5-volt alkaline batteries, or two AA 1.5-volt lithium
L91 batteries.
1-23
b. Electrical Function. Power from the batteries is supplied to
the components through the power switch as follows:
RESET/OFF Position With the power switch in the OFF

position, the circuit is not energized
from either the image intensifier or the
IR source. Also, turn the power switch
to this position to reset after highlight
cutoff.
ON Position Power is drawn from the battery

compartment to energize the goggles.
When the voltage drops to 2.4 Vdc, a
low-battery indicator at the right
eyepiece blinks indicating approxi-
mately 30 minutes of operating time.
WARNING

devices.
NOTE
Some goggles contain an additional momentary IR

function. For momentary IR, continue to turn the
power switch clockwise; past ON and without
pulling. The power switch will return to the ON
position when released.
1-24
CAUTION
Do not use excessive force to place the power

switch into the momentary IR position.
IR/PULL Position Power is drawn from the battery

compartment to energize the goggles
and IR light source and a steady red
indicator light in the left eyepiece.
WARNING

c. Automatic Shutoff. When some goggles are removed from

the headmount or helmet mount while in operation or flipped up in
the mount, they will not automatically cut off. They must be turned
off manually. To turn the goggles back on, turn the power switch
to RESET/OFF and then to ON again.
d. Highlight Cutoff. The goggles will automatically cut off after

70 ±30 seconds of operation in daylight or bright room light.
Individual bright lights (headlights, flashlights, or other
concentrated light sources) will not actuate the highlight detector
located on the front of the goggles. To turn the goggles back on,
turn the power switch to RESET/OFF position and then to ON
again.
1-25/26 blank
CHAPTER 2
OPERATING INSTRUCTIONS
Section I. Description and Use of Operator’s Controls

and Indicators
CAUTION
The NVG is a precision electro-optical instrument,

so handle it carefully.
NOTE
If the NVG fails to operate, refer to the

Troubleshooting Procedures in Chapter 3, Section
II.
2-1 OPERATOR CONTROLS AND INDICATORS
The NVG is designed to adjust for different users and controls for
most differences in eyesight. The controls and indicators for the
NVG are shown or described in Figure 2-1 and Table 2-1.
2-1
Figure 2-1. Goggles Controls and Indicators.
2-2
Table 2-1. Goggles Controls and Indicators.
CONTROLS AND FUNCTIONS

INDICATORS
Power Switch Controls goggles and IR source, ON or

OFF.
RESET/OFF – Same as System

OFF. Also resets
goggles after
automatic shut off or
highlight cutoff.
ON – Goggles activated.
CAUTION

NOTE
Some goggles contain an additional momentary IR

function. For momentary IR, continue to turn the
power switch clockwise; past ON and without
pulling. The power switch will return to the ON
position when released.
IR/PULL – Pull power switch

out and turn
clockwise to activate
goggles and IR
source.
2-3
Table 2-1. Goggles Controls and Indicators -
Continued.

INDICATORS
Low Battery Indicator When blinking (right eyepiece) it

indicates a low battery condition with
less than 30 minutes of battery life
remaining.
IR source On Indicator When illuminated (left eyepiece) it

indicates that the IR source is ON.
Objective Focus Focuses objective lens. Adjusts for

sharpest image of viewed object.
Diopter Adjustment Focuses eyepiece lens for each eye

without the need for glasses. Adjust
for sharpest image of intensifier
screen.
Interpupillary Adjustment Adjusts for distance between eyes by

sliding the eyepieces either together or
apart so each eye can observe the
entire field at the same time.
2-4
Table 2-1. Goggle Controls and Indicators - Continued.

INDICATORS
Eye Relief Adjustment Adjusts the distance between your eyes

and the goggles.
Latch Latch used for separation of goggles,

from headmount/helmet mount .
Battery Polarity This feature, molded into the goggles,

Indicators shows the proper orientation of the AA
and BA-5567/U batteries.
IR Spot/Flood Lens Focuses the IR source for a narrow

beam (spot) or wide angle (flood) beam
illumination.
Compass Illumination Pressing this button activates the

Button compass illumination LED which makes
the compass readings visible in the
goggles viewing area. Greater pressure
will make the image brighter. The image
disappears when the button is released.
2-5
Section II. Preventive Maintenance Checks and
Services (PMCS)
2-2 PREVENTIVE MAINTENANCE CHECKS AND

SERVICES TABLE
NOTE
The unit maintenance tracks the system for when

the 180 day service is due or any maintenance
that is performed by either hard copy or
automated. If using an automated system such as
Standard Army Maintenance System (SAMS) or
Unit Level Logistics System (ULLS), use the
equivalent electronic form, to track using the same
procedure as for the hard copy DA Form 2404,
2407 or DD Form 314 etc.
a. General. To ensure the readiness of the goggles, perform

the preventive maintenance procedures in accordance with Table
2-2, prior to each mission. Preventive maintenance procedures
include inspection, cleaning, and performance of the checkout
procedures.
b. Warnings and Cautions. Always observe the WARNINGS

and CAUTIONS appearing in the table. Warnings and cautions
appear before applicable procedures. You must observe the
warnings and cautions to prevent serious injury to yourself and
others, or to prevent your equipment from being damaged.
NAVY USERS. Refer to Maintenance Index Page (MIP) 7621/001

and Maintenance Requirement Cards (MRCs) GFEK N and GFEL
N for PMS requirements.
2-6
c. Explanation of Table Entries.
(1) Item Number Column. Numbers in this column are for

reference. When completing Equipment Inspection and
Maintenance Worksheet, include the item number for the
check/service indicating a fault. Item numbers also appear in the
order that you must do checks and services for the intervals listed.
(2) Interval Column. This column tells you when you must
do the procedure in the procedure column. BEFORE procedures
must be done before you operate or use the equipment for its
intended mission. DURING procedures must be done during the
time you are operating the equipment for its intended mission.
AFTER procedures must be done immediately after you have
operated or used the equipment.
(3) Location, Check/Service Column. This column

provides the location and the item to be checked or serviced. The
item location is underlined.
(4) Procedure Column. This column gives the procedure

you must do to check or service the item listed in the
Check/Service column to know if the equipment is ready or
available for its intended mission or for operation. You must do the
procedure at the time stated in the interval column.
(5) Not Fully Mission Capable If: Column. Information in

this column tells you what faults will keep your equipment from
being capable of performing its primary mission. If you make
check and service procedures that show faults listed in this
column, do not operate the equipment. Follow standard operating
procedures for maintaining the equipment or reporting equipment
failure.
2-7
NOTE
Damaged accessory items (compass, IR

Spot/Flood lens, sacrificial window, demist shields)
do not cause the entire end item to be “not fully
mission capable”. However, the damaged item
should be replaced as soon as practical to restore
full capability of the NVG.
d. Other Table Entries. Be sure to observe all special

information and notes that appear in your table.
2-8
Table 2-2. Preventive Maintenance Checks and Services for the NVG.
Location
Item Not Fully
No. Interval Check/ Procedure Mission
Service Capable If:
1. Before Maintenance Open carrying case, inventory

Forms and items and check for:
Records • Previously recorded faults on Fault not
maintenance records, corrected.
DA Form 2404.
GOGGLES
2. Before/ Optical Inspect all lenses (objective, Chips or heavy

After Surfaces eyepiece, IR lens and highlight scratches that
cutoff window) for dirt, fingerprint hinder vision
residue, chips, or cracks. If with goggles
necessary, clean and dry lenses turned ON,
with water and lens tissue. or if cracks are
present.
2-9
2-10
Table 2-2. Preventive Maintenance Checks and Services for the NVG -
Continued.
Location Not Fully
Item Interval Procedure Mission
No. Check/ Capable If:
Service
3. Before/ Wired Body Inspect external surfaces and Cracks or dam-

After Housing latch for cracks or damage. age in the
Scratches and gouges are OK if wired body
operation is not affected. housing.
Inspect battery compartment. Cap is missing,

Check to make sure the battery contacts
cap and battery cap retainer is damaged, or
present. Remove battery cap and corroded,
inspect for moisture, cracks, o-ring is
corroded or defective spring missing.
contacts, and o-ring present in
cap.
Continued.
Location Not Fully
Item Interv Procedure Mission
No. al Check/ Capable If:
Service
3. Before/ Wired Body Remove any batteries and turn the Power switch
Cont. After Housing power switch from RESET/OFF to has no definite
Cont. ON to IR/PULL. Each position stopping points
should have a definite stopping point. or knob is bro-
Inspect for broken or missing knob. ken or missing.
Install batteries per paragraph 2-6 and IR source does
check IR source (and momentary IR not work, or it
source, if so equipped) functions by works and the
following the operating instructions in red light does
paragraph 2-25. not appear in
the left eyepiece.
Check the highlight cutoff with day- If damaged,
light or bright room light (not fluores- refer to higher
scent light) by placing the objective lens level of
cap on the objective lens. Turn the maintenance.
goggles ON and observe that the sys-
2-11
tem cuts off within 70 ±30 seconds.
2-12
Continued.
Location Not Fully
Service
3. Before/ Wired Body Turn goggles OFF and then ON to

Cont. After Housing reenergize goggles.
Cont.
NOTE
If the goggles fail this high-
light cutoff test, it does not
cause the end item to be non-
mission capable. However, it
should be sent to higher level
of maintenance as soon as
practical.
4. Before/ Rear Cover Inspect external surfaces for cracks Cracked or

After or damage. Scratches and gouges damaged.
are okay if operation is not affected.
Continued.
Location Not Fully
Service
4. Before/ Rear Cover Rotate diopter adjustment to Binding, not

Cont. After Cont. make sure the eyepiece lenses moving freely or
move freely and are not loose. too loose.
Range is approximately ½ turn.
Check diopter cell retainers for Retainers will

chips. not hold eye-
cup securely.
Check interpupillary adjustment by Not achieving or

sliding each eyepiece lens back maintaining
and forth for binding or looseness. interpupillary
adjustment.
NOTE
There is a certain amount of
friction present to keep the
2-13
eyepiece lenses from moving
once you set them. This is okay.
2-14
Continued.
Location Not Fully
Service
5. Before/ Eyecups Inspect for dirt, dust, cracked or torn Chips and
After eyecups. Inspect for bent, broken, or cracks are
improperly fitting eyecups. If permitted on the
necessary, clean with water. eyecup retain-
ing rings as long
as they do not
interfere with in-
stallation of eye-
cup.
6. Before/ Objective Lens Rotate focus adjustment to ensure free Focus adjust-
After movement (range is approximately ment is binding
1/3 turn). Check objective lens for or not able to
chips, cracks and dents. move.
Continued.
Location Not Fully
Service
6. Before/ Objective Lens Chips, cracks, or

Cont. After Cont. dents prevent
full field-of-view,
installation of
LIF or the ability
to focus.
Check the infinity focus locking ring Cracked or

for tightness. Check for cracks. loose.
7. Before/ Neck Cord and Inspect for cracked, torn, or missing Damaged.
After Objective Lens objective lens cap. Inspect neck
Cap cord for cut, damage, or loose ends.
Re-tie ends if necessary.
2-15
2-16
Continued.
Location Not Fully
Service
NOTE
Operator may use the
TS-4348/UV to check
resolution (paragraph 2-3).
8. Before/ Viewed Image Refer to paragraph 2-4 to inspect Flickering,
After for operational defects. flashing, edge
glow, or shading
NOTE is observed.
If any of the following items are

damaged it does not cause the
entire end item to be “not fully
mission capable”. However,
the damaged item should be re-
placed as soon as practical to
restore full capability of the
system.
Continued.
Location Not Fully
Service
HEADMOUNT
9. Before/ Straps/Pads Inspect for cuts, tears, fraying, Damage causes

After holes, cracks, or defective straps or pads to
fasteners. be unservice-
able.
10. Before/ Socket Inspect for dirt, dust, or corrosion. Damaged latch
After Insert goggles latch into socket to won’t lock or is
verify secure attachment of too loose.
goggles to headmount. If
necessary, clean socket with water.
11. Before/ Eye Relief Press the eye relief adjustment and Binding,
After Adjustment check for free motion. Inspect for damaged or
damage. non-operational
2-17
slide
mechanism.
2-18
Continued.
Location Not Fully
Service
HELMET MOUNT
12. Before/ Straps Inspect for cuts, tears, fraying, holes, Damage causes
After cracks, or defective fasteners. straps to be
unserviceable.
13. Before/ Socket Inspect for dirt, dust, or corrosion. Damaged latch
After Insert goggles latch into socket to won’t lock or is
verify secure attachment of goggles too loose.
to helmet mount. If necessary, clean
socket with water.
14. Before/ Fore-and-Aft Press the 2 side buttons on plastic Binding,

After Adjustment mount or depress side lever on damaged or
metal mount and check for free non-operational
motion. Inspect for damage. slide
mechanism.
Continued.
Location Not Fully
Service
ACCESSORIES
CAUTION
The coating on the demist
shield can be damaged if
cleaned while wet or if cleaned
with wet lens paper. Clean only
when the demist shield is dry
and only with dry paper.
15. Before/ Demist Shields Inspect for dirt, dust, scratches or Damage or
After damage. If necessary, clean when scratches hinder
shields are dry and with dry lens vision with
tissue only. goggles ON.
2-19
2-20
Continued.
Location Not Fully
Service
16. Before/ LIF Inspect for dirt, dust, scratches or Damage or

After damage. If necessary, clean with scratches hinder
water and dry with lens tissue per vision with
paragraph 3-2. goggles ON.
17. Before/ Sacrificial Window Inspect for dirt, dust, scratches or Damage or
After damage. If necessary, clean with scratches hinder
water and dry with lens tissue per vision with
paragraph 3-2. goggles ON.
18. Before/ IR Spot/Flood Rotate IR Spot/Flood lens to ensure Not free moving.
After Lens free movement.
19. Before/ Compass Inspect for dirt, dust, scratches, or Damaged or

After damage. If necessary, clean with compass is not
water and dry with lens tissue. visible.
Continued.
Location Not Fully
Service
19. Before/ Compass Install compass and turn on goggles.

Cont. After Cont. When the illumination button is
depressed, compass should
be visible.
CARRYING
CASE
20. Before/ Case Remove all items and shake out loose
After dirt or foreign material. Inspect for
tears, cuts, excess wear, or damage
to mounting clips.
21. Before/ Shoulder Strap Inspect for cuts, tears, or excess wear
After or damaged clips.
2-21
During None
2-3 RESOLUTION CHECK USING THE TS-4348/UV
TEST SET
NOTE
• The TS-4348/UV test set can be used by the

operator or unit maintenance to check the
resolution of an NVG at any time.
NOTE
• The TS-4348/UV test set can be used by

Direct Support/Intermediate Level to perform
the resolution testing 180 Day Service. If a
system fails it must be tested on the TS-
3895A/UV Test Set.
NOTE
Verify the resolution of the goggles using the

TS-4348/UV test set at every opportunity. The
resolution cannot be accurately measured without
the test set.
The following procedures are designed to check the performance

of the image intensifier.
a. Setup. Before using the TS-4348/UV test set, refer to

TM 11-5855-299-12&P to set up and familiarize yourself with its
operation and the warnings and cautions associated with that test
equipment.
2-22
NOTE
• The resolution test must be performed in a

darkened area. Your eyes must be dark-
adapted to perform the test. Review the
following test procedure before entering the
dark area.
• Expect cosmetic blemishes, such as

chicken wire, black spots, and fixed-pattern
noise, to stand out while viewing through the
TS-4348/UV test set when it is on the
highlight level. This is acceptable.
2-23
b. Low Light and Highlight Resolution Test Procedure.
Test the goggles for low light and highlight resolution performance
according to the following steps.
(1) Place the HIGH/LOW switch on the test set to the LOW
position.
(2) Install the LIF per paragraph 2-11.
(3) Turn OFF the room light and let your eyes adjust to the
dark.
(4) Turn ON the test set by setting the “II/OFF/III” switch to

the “III” position.
(5) Turn ON the goggles and insert it into the test port on
the test set.
(6) Look through the goggles and view the projected pattern
(see Figure 2-2). If necessary, focus the eyepiece lenses and then
the objective lens to obtain the sharpest image.
(7) The goggles must be able to resolve Group 2, Element

2, under low light conditions to pass the test. If the goggles do not
pass the test, return it to maintenance for repair.
ARMY ONLY – The operator must document resolution failures on
the maintenance record.
2-24
Figure 2-2. TS-4348/UV Test Set Pattern.
2-25
NOTE
For a pattern to be resolvable, three vertical bars

and three horizontal bars must be visible.
(8) Flip the HIGH/LOW switch to the HIGH position.
(9) Again, look through the goggles and view the projected
pattern (see Figure 2-2). If necessary, refocus the objective lens
and then the eyepiece lenses to obtain the sharpest image.
(10) The NVG must be able to resolve Group 3, Element 5,

under highlight conditions to pass the test. If the goggles do not
pass the test, send it to a higher level of maintenance for repair.
NOTE
When using the TS-4348/UV test set, you are not

viewing the entire image intensifier. Therefore,
operational and cosmetic inspections must be
done without the test set as specified in paragraph
2-4.
(11) Look for flashing, flickering, or other nonstable behavior

of the image intensifier. Also check the image intensifier for other
operational defects described in paragraph 2-4. To view the image
intensifier under low light conditions, flip the HIGH/LOW switch to
the LOW position and allow your eyes to become accustomed to
the dark. If any unacceptable conditions are noted, return the
goggles to maintenance.
2-26
2-4 INSPECTION CRITERIA FOR PROPER IMAGE
INTENSIFIER OPERATION
a. General. As directed in the Preventive Maintenance Checks

and Services table, image intensifier operation must be checked
before each mission. This section provides information for the
operator concerning what to look for, how to look for it, and how to
determine if the NVG should be returned to the maintainer. The
operator (Army only) must record all conditions on the
appropriate maintenance forms and describe the specific
defects and sign it so the maintainer can take corrective
action.
CAUTION
Perform the following inspection in the dark.
To perform this inspection, attach the goggles to the headmount or

helmet mount as described in paragraph 2-21 or 2-22 and turn the
power switch to the ON position. Look through the goggles and
view the image.
There are two groups of “defects” you may encounter - operational

defects and cosmetic blemishes. Operational defects are an
immediate cause to reject the NVG. Cosmetic blemishes are not a
cause for rejection unless they become severe enough to interfere
with the ability to perform the mission. The rejection of any NVG
for cosmetic defects must be based on an outdoor evaluation
and not the TS-4348/UV test set.
2-27
b. Operational Defects. These defects relate to the reliability of
the image intensifier and are an indication of instability. If
identified, they are an immediate cause for rejecting the NVG.
They include shading, edge glow, flashing, flickering, and
intermittent operation.
(1) Shading. If shading is present, you will not see a fully

circular image (see Figure 2-3). Shading is very dark and you
cannot see an image through it. Shading always begins on the
edge and migrates inward eventually across the entire image area.
Shading is a high contrast area with a distinct line of demarcation.
Return the NVG to the maintainer.
Figure 2-3. Shading.
2-28
NOTE
Make sure the shading is not the result of

improper eye-relief adjustment (refer to paragraph
2-22).
(2) Edge Glow. Edge glow is a bright area (sometimes

sparkling) in the outer portion of the viewing area (see Figure 2-4).
To check for edge glow, block out all light by cupping a hand over
the objective lens. If the image intensifier is displaying edge glow
the bright area will still show up. Return the NVG to the
maintainer.
Figure 2-4. Edge Glow.
(3) Flashing, Flickering, or Intermittent Operation. The

image may appear to flicker or flash. If there is more than one
flicker, check for loose battery cap or weak battery. If weak or
loose batteries are not the problem return the NVG to the
maintainer.
2-29
c. Cosmetic Blemishes. These are usually the result of
manufacturing imperfections that do not affect image intensifier
reliability and are not normally a cause for rejecting a NVG.
However, some types of blemishes can get worse over time and
interfere with the ability to perform the mission. If you believe a
blemish is cause for rejection, record the specific nature of the
problem on the maintenance forms and identify the position of the
blemish by using the clock method and approximate distance from
the center (e.g., 5 o’clock toward the outside, 2:30 near the center,
or 1:00 midway). The following are cosmetic blemishes:
(1) Bright Spots. A bright spot is a small, nonuniform, bright

area that may flicker or appear constant (Figure 2-5). Not all bright
spots make the NVG rejectable. Cup your hands over the
objective lens to block out all light. If the bright spot remains,
return the NVG to the maintainer. Bright spots usually go away
when the light is blocked out. Make sure any bright spot is not
simply a bright area in the scene you are viewing. Bright spots
are acceptable if they do not interfere with the operator's
ability to view the image or to perform the mission.
2-30
Figure 2-5. Bright Spots and Emission Points.
(2) Emission Points. A steady or fluctuating pinpoint of

bright light in the image area that does not go away when all light
is blocked from the objective lens (Figure 2-5). The position of an
emission point within the image area does not move. Not all
emission points make the NVG rejectable. Make sure any
emission point is not simply a point light source in the scene you
are viewing. Emission points are acceptable if they do not
interfere with the operator's ability to view the image or to
perform the mission.
(3) Black Spots. These are cosmetic blemishes in the

image intensifier or dirt or debris between the lenses. Black spots
are acceptable as long as they do not interfere with viewing the
image. No action is required if this condition is present unless
the spots interfere with the operator's ability to view the image
or to perform the mission.
2-31
(4) Fixed-Pattern Noise. This is usually a cosmetic blemish
characterized by a faint hexagonal (honeycomb) pattern
throughout the viewing area that most often occurs at highlight
levels or when viewing very bright lights (see Figure 2-6). This
pattern can be seen in every image intensifier if the light level is
high enough. This condition is acceptable as long as the
pattern does not interfere with the operator's ability to view
the image or to perform the mission.
Figure 2-6. Fixed Pattern Noise.
2-32
(5) Chicken Wire. An irregular pattern of dark thin lines in
the field-of-view either throughout the image area or in parts of the
image area (see Figure 2-7). Under the worst case condition,
these lines will form hexagonal or square-wave shaped lines. No
action is required if this condition is present unless it
interferes with the operator's ability to view the image or to
perform the mission.
Figure 2-7. Chicken Wire.
2-33
Section III. Assembly and Preparation for Use
This chapter contains the information necessary to prepare the

goggles for operation. This includes unpacking (2-5), battery
installation (2-6), eyecups installation (2-7), demist shields
installation (2-8), sacrificial window installation (2-9), compass
installation (2-10) LIF installation (2-11), IR Spot/Flood lens
installation (2-12) headmount installation and adjustment (2-13),
headmount installation with protective mask (2-14), headmount
with helmet installation (2-15), original helmet mount to helmet
installation (2-16) new helmet mount to helmet installation (2-17)
new helmet mount with new nape strap to helmet installation (2-
18), AN/PVS-7D helmet mount to helmet installation (2-19) and 3X
magnifier installation (2-20).
2-5 UNPACKING
The following steps must be accomplished prior to each mission

where the goggles are used.
CAUTION
Before releasing latches on the old shipping and

storage case, relieve air pressure inside shipping
and storage case by pressing relief valve button
located near the case handle.
(1) Release the two latches securing top of shipping and

storage case and open.
(2) Check contents for completeness (see Figure 1-1).
(3) Remove carrying case. Open carrying case (Figure 1-

1), remove goggles, and check contents for completeness.
2-34
(4) Inspect the goggles for obvious evidence of damage to
optical surfaces, body, eyecups, power switch, battery cap, etc.
Ensure that all optical surfaces are clean and ready for use. Clean
with lens paper.
2-6 INSTALLATION OF BATTERIES
CAUTION
To protect the image intensifier, keep the objective

lens cap on when the monocular is not in use or
when using the NVG in daylight conditions.
The NVG will operate with any of the battery types identified in
Table 2-3. Batteries are not supplied with the NVG and must be
obtained separately.
Table 2-3. Estimated Battery Life.
BATTERY NEGLIGIBLE IR SOURCE USAGE

TYPE IR SOURCE 10%
USAGE OF THE TIME
BA-5567/U (Lithium) 22 Hrs. 20 Hrs.

AA Alkaline 60 Hrs. 55 Hrs.
AA Lithium L91 70 Hrs. 65 Hrs.
2-35
NOTE
The battery data in Table 2-3 represents operation

under room temperature. When operating under
cooler conditions, battery life will decrease.
CAUTION
• Do not mix battery types (i.e., Alkaline and

Lithium).
• Make certain the power switch is in the OFF

position before installing batteries.
Install either two AA batteries or one BA-5567/U lithium battery as

follows. Do not mix battery types.
(1) Remove the battery cap by turning it counterclockwise.
(2) Check to ensure the o-ring is present. Replace if

missing.
(3) Observe polarity, as indicated on the outside of the

battery compartment, and insert either two AA 1.5-volt batteries or
one 3.0-volt BA-5567/U battery into battery compartment, plus (+)
end first (Figure 2-8).
2-36
Figure 2-8. Battery and Eyecup Installation.
(4) Replace battery cap by pushing and turning it clockwise.

Tighten it firmly to ensure a watertight seal.
2-7 INSTALLATION OF EYECUPS
Install eyecups as follows: Refer to Figure 2-8.
(1) Carefully press each eyecup over the diopter cell

retainer.
(2) Rotate each eyecup into proper viewing position. Adjust

for best eye fit. The eyecups must seal around your eyes to
prevent the green glow from escaping.
2-37
2-8 INSTALLATION OF DEMIST SHIELDS
Install the demist shields as follows: Refer to Figure 1-2.
CAUTION
If the demist shields need to be cleaned, make

sure they are dry and use dry lens paper to clean.
If the demist shields are wiped while wet or with
wet lens paper, you will damage the coating.
NOTE
If inclement operating conditions are expected
(e.g. significant temperature change and high
humidity), install demist shields to minimize
eyepiece lens fog prior to mission.
(1) Carefully remove eyecups.
(2) Carefully press a demist shield onto each eyepiece. Be

careful not to smudge the eyepieces or demist shields.
(3) Install the eyecups per paragraph 2-7.
2-9 INSTALLATION OF SACRIFICIAL WINDOW

Install the sacrificial window as follows: Refer to Figure 1-2.
CAUTION
If adverse operating conditions (dust or sand), are

expected, attach the sacrificial window to protect
the objective lens from scratches or other damage.
(1) If the compass or objective lens cap is in place, remove

it.
2-38
(2) Carefully push the sacrificial window onto the objective
lens until it stops. Turn the sacrificial window clockwise until it
snaps into place.
2-10 INSTALLATION OF COMPASS
CAUTION
• Use of the compass with the plastic

headmount or the plastic helmet mount will
result in inaccurate compass readings. The
magnet cannot be removed from these
mounts.
• The magnet must be removed from the

ruggedized metal helmet mount before
installation of the compass. Failure to do so
will result in inaccurate compass readings.
• If the magnet is not removed, turn the

ruggedized metal helmet mount in to unit
maintenance for removal. See Figure 2-9 for
location of magnet.
Figure 2-9. Locating the Magnet.
2-39
NOTE
• Prepare the goggles for operation.
• Leave LIF in place when installing the

compass.
• The tethering cord can be used to tether the

compass to your person to prevent losing the
compass if it is dropped. To use the tethering
cord, tie the end without the clip tightly
around the compass and attach the clip to a
buttonhole, belt loop or other convenient
point.
(1) If the sacrificial window or objective lens cap is in place,

remove it.
(2) Turn goggles ON.
(3) Rotate the objective lens focus completely

counterclockwise (while looking through the goggles).
NOTE
The o-ring must be in place in the compass in

order for the compass to fit properly.
(4) Press the compass onto the objective lens at an angle

using your left hand. Slowly turn the compass counterclockwise
until it is the vertical position (with compass illumination button
pointing down). See Figure 2-10.
(5) Ensure that the compass fits tightly.
2-40
Figure 2-10. Compass Installation.
(6) Refer to paragraph 2-24 for operation of the compass.
2-11 INSTALLATION OF LIF
Install the LIF as follows:
(1) Remove the container/wrench from the carrying case

(Figure 1-1).
CAUTION
Be careful not to touch glass surfaces. If you get

fingerprints or contamination on glass surfaces,
use lens paper to clean the LIF. If moisture is
needed, use your breath to mist the surface of the
glass.
(2) If the objective lens cap, compass, or sacrificial window

is on the objective lens, remove it.
2-41
(3) Carefully open the container/wrench and remove the
LIF. Refer to Figure 2-11.
Figure 2-11. LIF.
(4) Hold the LIF by the ridged end (see Figure 2-11) and
thread it clockwise, into the objective lens.
CAUTION
Do not overtighten the LIF into the objective lens.
(5) Using the ridged side of the container/wrench as a

wrench, engage the ridges on the container with the ridges on the
LIF and tighten the LIF hand tight.
(6) Place the empty container/wrench back into the carrying

case.
2-42
NOTE
• The objective lens cap, compass, or the sacrificial

window will fit onto the end of the objective lens
with the LIF in place. On some systems when the
LIF is installed, the objective lens cap or the
sacrificial window will not fit on the objective lens
as completely as on other systems.
• The LIF must be used at all times unless directed

by the unit commander to remove the LIF, based
upon his/her assessment of the laser threat in the
theater of operations. Use of this filter will result in
a slight reduction in system gain.
(7) Install the objective lens cap or the sacrificial window

over the LIF.
2-12 INSTALLATION OF IR SPOT/FLOOD LENS
Press the IR spot/flood lens over the IR source window until it is

tight against the goggles. Refer to Figure 2-12.
2-43
Figure 2-12. IR Spot/Flood Lens Installation.
2-13 INSTALLATION AND ADJUSTMENT OF

HEADMOUNT
Don the headmount as follows:
NOTE
Do not don the headmount while the goggles are

attached.
(1) Prior to donning the headmount, loosen the four ends of

the chinstrap approximately two inches from the sliding bar buckles
(Figure 2-13).
(2) Snap the front (Figure 2-13), and rear snaps in place.
2-44
Figure 2-13. NVG Headmount Adjustments.
2-45
NOTE
If the headmount is too loose, remove the

attached thin browpad (Figure 2-13) and replace
with either the medium or thick browpad stored in
the carrying case. Refer to paragraph 3-3(1) for
removal and replacement of the browpads.
(3) With both hands, grasp the neck pad (Figure 2-13) and
pull the harness over your head and the neck pad down to the
back of your neck.
(4) Holding the chin cup in position on chin, adjust both

sides of the chinstrap until you feel light pressure against your
chin. (DO NOT TIGHTEN.)
(5) Maintain the position of the chin cup and remove any
slack from the front and rear chinstraps. (DO NOT TIGHTEN.)
(6) Ensure that the cross-strap is not twisted and remove

slack by adjusting the vertical adjustment at the neck pad.
(7) Adjust chinstrap and vertical adjustment until the chin

cup and headmount are in a comfortable but firm position.
NOTE
After installing the goggles, minor strap

adjustments may be necessary to achieve
comfort.
(8) Refer to paragraph 2-21 for operating procedures.
2-46
2-14 INSTALLATION OF HEADMOUNT WITH
PROTECTIVE MASK
(1) Place protective mask on your head per the instructions

provided with the protective mask.
WARNING
When installing the headmount over the protective

mask, be careful not to break the protective mask
seal around your face.
(2) Install the headmount per the instructions in paragraph

2-13.
NOTE
It may be necessary to remove the browpad

(Figure 2-13) when wearing the headmount over a
protective mask.
2-15 INSTALLATION OF HEADMOUNT WITH HELMET
Install the headmount per the instructions in paragraph 2-13. The

helmet is worn over the headmount.
2-47
2-16 INSTALLATION OF ORIGINAL HELMET MOUNT
TO HELMET
(1) Remove helmet mount (Figure 1-3) from the carrying

case. Refer to Figure 2-14 for the helmet mount features.
Figure 2-14. Helmet Mount Features.
2-48
(2) Ensure that the strap is adjusted so that the “M” marking
is aligned with the top of the helmet mount block (See Figure 2-
15.)
Figure 2-15. Helmet Strap Size Adjustment.
(3) With catch in forward most position, place the strap over
the top of the helmet, center and hook the rear bracket onto the
rear of the helmet. Center the front bracket, hook it on the front of
the helmet and hold it in place. (See Figure 2-14.)
(4) With the buckle lever open, take up the slack in the strap
using catch. Close the buckle lever. (See Figure 2-16.)
(5) Place helmet upside down with helmet mount facing you.
2-49
Figure 2-16. Buckle and Catch.
NOTE
Steps 6 and 7 describe the installation of the nape

strap to the chinstrap. To accomplish these steps,
it may be necessary to unthread the chinstrap
from the helmet.
(6) Thread chinstrap through right end of nape strap and

snap nape strap fastener tab closed (refer to Figure 2-17).
2-50
(7) Thread chinstrap through left end of nape strap and
snap nape strap fastener tab closed (refer to Figure 2-17).
(8) Disengage the nape strap latch on left side of nape

strap.
Figure 2-17. Nape Strap Installation.
(9) Don the helmet.
2-51
(10) Engage the nape strap at the nape strap latch. Tension
the chinstrap and nape strap for a secure and stable fit. The brow
of the helmet should be parallel with the ground.
2-17 INSTALLATION OF NEW HELMET MOUNT TO

HELMET
(1) Remove the helmet mount (Figure 1-3) from the carrying
case. Make sure the helmet mount is complete. Refer to Figure 2-
18 for the helmet mount components and features.
Figure 2-18. Helmet Mount Components and Features.
2-52
CAUTION
To prevent possible equipment damage, remove

both the goggles and the helmet mount from the
helmet when not required for immediate use. The
strap can remain in place on the helmet.
(2) If the helmet mount and strap are connected, remove the
helmet mount. To do this, push the release lever at the top center
of the helmet mount and slide the two assemblies apart.
(3) The strap attaches to the helmet the same as the

original helmet mount. Perform steps in paragraph 2-16 to install
the strap.
NOTE
The strap is now properly attached to the helmet.
(4) If the helmet has its cloth cover and camouflage strap
installed, it will be necessary to slide the camouflage strap up (at
about a 30° – 45° angle) at the front of the helmet (see Figure 2-
18).
This step is required in order to prevent the helmet mount from

catching on the camouflage strap when the helmet mount is
installed on the strap.
2-53
(5) To install the helmet mount into the strap, place it over
the top of the mounting clip and slide it down until it locks into
place with a click (see Figure 2-19).
Figure 2-19. Attaching the Helmet Mount to the Strap.
2-54
2-18 INSTALLATION OF NEW HELMET MOUNT WITH
NEW NAPE STRAP TO HELMET
(1) Remove the helmet mount (Figure 1-3) from the carrying
case. Make sure the helmet mount is complete. Refer to Figure 2-
20 for the helmet mount components and features.
CAUTION
To prevent possible equipment damage, remove

both the goggles and the helmet mount from the
helmet when not required for immediate use. The
Figure 2-20. Helmet Mount Features (New Nape Strap).
2-55
(2) If the helmet mount and strap are connected, remove the
helmet mount. To do this, push the release lever at the top center
of the helmet mount and slide the two assemblies apart.
(3) Adjust the strap to fit the helmet size being used.
(4) With the catch in the most extended position, place the
strap over the top of the helmet, center and hook the rear bracket
onto the rear of the helmet. Center the front bracket hook on the
front of the helmet and hold it in place (see Figure 2-21).
using catch. Close the buckle lever (see Figure 2-16).
(6) If the helmet has its cloth cover and camouflage strap
installed, it will be necessary to slide the camouflage strap up (at
about a 30° – 45° angle) at the front of the helmet (see Figure 2-
21).
This step is required in order to prevent the helmet mount from

catching on the camouflage strap when the helmet mount is
installed on the strap.

strap.
(8) Don the helmet. Do not fasten the helmet chinstrap.
2-56
Figure 2-21. Attaching Helmet Mount to Strap (New
Nape Strap).
the nape strap for a stable fit, then install and tension the helmet
chinstrap. The brow of the helmet should be parallel to the ground
and the helmet stable on the head.
(10) To install the helmet mount into the strap, place it over
the top of the mounting clip and slide it down until it locks into
place with a click (see Figure 2-21).
2-57
2-19 INSTALLATION OF AN/PVS-7D HELMET MOUNT
TO HELMET
a. Using Helmet Mount Strap.
(1) Remove the helmet mount (Figure 1-3) from the

carrying case. Refer to Figure 2-22 for helmet mount features.
Figure 2-22. Installation of Helmet Mount.
2-58
(2) Press the release button (Figure 2-23) to remove the
mount from the helmet mount bracket.
Figure 2-23. Helmet Mount.
(3) Make sure the strap is laced onto the helmet mount
bracket as shown in Figure 2-22.
(4) With catch (see Figure 2-22) in forward most position,

place the strap over the top of the helmet center (see Figure 2-23).
(5) Hook the rear bracket on the center of the back of the
helmet and lay the strap with helmet mount bracket over the top of
helmet.
2-59
(6) Hook the helmet mount bracket in the center of the front
lip of the helmet and hold it in place.
using the catch. Close the buckle lever.

strap.
(11) Insert the top edge of the mount under the keeper on the
helmet mount bracket and rotate downward until the latch
engages. (See Figure 2-24) To release the mount from the
helmet bracket, press the release button (see Figure 2-23) and pull
forward and down.
2-60
Figure 2-24. Installation of Helmet Mount.
b. MARINE CORPS ONLY – Using Existing Helmet Screw

(no strap).
NOTE
Refer to Figures 2-24 and 2-25 for reference and

definition of terms.
(1) Remove the helmet mount from the carrying case.
(2) Press the release button to remove the mount from the
helmet mount bracket.
(3) Unthread the strap from the helmet mount bracket.

Unsnap the rear snap and remove the rear mount bracket from the
strap.
2-61
Figure 2-25. Helmet Mount.
NOTE
Place the strap in the carrying case – it is not used

for this mounting method.
(4) Find the screw located in the front center of the helmet.
Using a flat tip screwdriver, remove the screw. Hook the helmet
mount bracket on the front of the helmet and center it over the hole
where the screw was removed.
(5) Insert the screw removed in step 4 above through the

hole in the helmet mount bracket and through the helmet (see
Figure 2-25).
2-62
(6) Align the nut on the helmet’s interior strapping to the
hole and tighten the screw with a flat tip screwdriver.
(7) Attach the mount to the helmet mount bracket. Insert

the top edge of the mount under the keeper on the helmet mount
bracket and rotate downward until the latch engages (see Figure 2-
24). To release the mount from the helmet bracket, press the
release button (see Figure 2-25) and pull forward and down.
(8) Find the screw located in the lower rear, center of the
helmet. Using a flat tip screwdriver, remove the screw. Hook the
rear bracket on the lower rear of the helmet and center it over the
hole where the screw was removed.
(9) Insert the screw removed in step 8 through the hole in

the rear bracket and through the helmet.
(10) Align the nut to the hole and tighten the screw with the
flat tip screwdriver.

strap.
(14) Insert the top edge of the mount under the keeper on the
helmet mount bracket and rotate downward until the latch engages
(see Figure 2-24). To release the mount from the helmet bracket,
press the release button (Figure 2-25) and pull forward and down.
2-63
2-20 INSTALLATION OF 3X MAGNIFIER
The 3X magnifier can be threaded directly into the objective lens,

with the LIF removed. It can also be threaded into the focus ring
adapter and slipped on over the end of the objective lens with the
LIF installed.
Figures 2-26 and 2-27 illustrate these installation procedures.
NOTE
The tethering cord can be used to tether the 3X

magnifier to your person to prevent losing the lens
if it is dropped. To use the tethering cord, tie the
end without the clip tightly around the 3X magnifier
and attach the clip to a button hole, belt loop or
other convenient point.
2-64
Figure 2-26. 3X Magnifier Installation without LIF
Figure 2-27. 3X Magnifier Installation with LIF in Place.
2-65
Section IV. Operating Procedures
This section contains operating procedures for using the NVG as

hand-held, head mounted or helmet mounted goggles. Prior to
operating the goggles, make certain that all steps in Section III,
Assembly and Preparation for Use, have been read and
performed.
2-21 HEAD MOUNTED OPERATION
CAUTION
Operate the goggles only under darkened

conditions or use the objective lens cap to cover
the objective lens for daylight conditions.
(1) Ensure that batteries are installed per paragraph 2-6.
(2) Don the headmount per instructions in paragraph 2-13.
NOTE
Paragraphs 2-14 and 2-15 provide additional

information required when installing the
headmount with a protective mask, or helmet.
2-66
NOTE
To make it easier to align the goggles, eyecups and

eyepiece lenses to the eyes, depress the eye relief
adjustment (Figure 2-13) and slide the headmount socket all
the way forward before attaching the goggles.
(3) Align the goggles’ latch (Figure 2-1) to the headmount

socket (Figure 2-13). Press and hold down the latch lever while
installing the goggles into the headmount socket (Figure 2-13).
Release the latch (Figure 2-1) when the goggles fully engage the
socket.
(4) Set your eye relief by depressing the eye relief

adjustment (Figure 2-13) and move the goggles back toward your
eyes until the eyecups comfortably seal around the eyes.
(5) Turn the power switch to ON.
(6) Adjust the interpupillary distance (Figure 2-1) by sliding

the eyepiece lenses together or apart so each eye can observe the
entire field-of-view at the same time. The eyepiece lenses adjust
independently.
(7) Readjust the vertical adjustment (Figure 2-13) of the

headmount until the goggles are properly aligned with your eyes.
2-67
NOTE
• The sharpest image will be observed only

when the objective lens and both eyepiece
lenses are properly focused.
• Fold the eyecup to obstruct your view through

the eyepiece lens instead of closing one eye
to prevent the eye from being temporarily out
of focus.
(8) Fold the right eyecup over the eyepiece lens with your
right thumb or forefinger to obstruct view through the right
eyepiece lens. Rotate the left diopter adjustment for the clearest
view of the image intensifier screen.
(9) Fold the left eyecup over the eyepiece lens with your left
thumb or forefinger to obstruct view through the left eyepiece lens.
Rotate the right diopter adjustment for the clearest view on the
image intensifier screen.
NOTE
Any readjustment of eye relief requires resetting

the diopter adjustments.
(10) Adjust the eye relief distance by pressing the eye relief
adjustment (Figure 2-13) and sliding goggles fore or aft to obtain a
full field-of-view of the image. Reset the diopter adjustments for
best image.
(11) Adjust the objective lens focus ring (Figure 2-1) while
observing an object until the sharpest image is obtained.
2-68
2-22 HELMET MOUNTED OPERATIONS
CAUTION
• Take some precautions when using/handling

the helmet mount. Most damage occurs
when the helmet mount is left on the helmet
when not needed for immediate use.
Observe the following cautions to significantly
extend the useful life of the helmet mount.
• Damage in the field has occurred when the

goggles are mounted to the helmet mount
and are in the flipped up position.
• Disconnect the helmet mount from the helmet

and properly stow it when not needed for
immediate use.
• Do not drop or throw the helmet with the

helmet mount attached to it.
• The goggle and helmet mount should not be

left on the helmet when the helmet is
removed.
• With the goggle in the flipped UP position, do

not flick the goggle down by shaking the
helmet. This places significant stress on the
helmet mount or on the latch.
• When not in use, properly stow the helmet

mount in the carrying case or other protected
location.
2-69
NOTE
• For the three newer model helmet mounts

which have a quick disconnect feature, the
However, the protruding goggle mount
portion should be removed.
• The helmet mount provides two positions for

the user to position the goggles. The flipped
down position allows the user to position the
goggles directly in front of the eyes. The
helmet mount also allows the user to rotate
the goggles to a flipped up position when the
goggles are not needed for immediate use.
Both the flipped down and the flipped up
positions have a positive stop which assures
the user that the goggles are in the correct
position.
• Marine Corps Only – If you have the newest

version helmet mount which comes with the
AN/PVS-7D, use the helmet screws to mount
the helmet mount bracket directly to the
helmet per paragraph 2-19b.
• All Other Services – If you have the newest

version helmet mount, return the helmet and
the helmet mount to unit maintenance for
direct mounting of the bracket via the helmet
screws.
NOTE
Operation of the goggle is the same with any

version of the helmet mount.
2-70
(2) Don the helmet mount per paragraph 2-16 (original

style), 2-17 (new style with quick disconnect), 2-18 (new quick
disconnect with new nape strap) or 2-19 (AN/PVS-7D version).
(3) Place the goggles in the socket of the helmet mount.

Set your eye relief by depressing the side buttons (or press down
on side lever on metal mount) (see Figure 2-28) and carefully
move the goggles fore or aft until the eyecups comfortably seal
around the eyes. Readjust the helmet straps as required for
vertical adjustment.
(4) Turn power switch to ON. Adjust the tilt by using the tilt
adjustment lock knob (or tilt adjustment lever on metal mount)
(Figure 2-28) until you obtain a comfortable viewing angle.

independently. If necessary, readjust the eye relief.
Figure 2-28. Tilt and Flip-up Mechanisms.

2-71
NOTE
The sharpest image will be observed only when

the objective lens and both eyepiece lenses are
properly focused.
(6) Fold the right eyecup over the eyepiece lens with your
right thumb or forefinger to obstruct view through the right
eyepiece lens. Rotate the left diopter adjustment for the clearest
view of the image intensifier screen.
(7) Fold the left eyecup over the eyepiece lens with your left
thumb or forefinger to obstruct view through the left eyepiece lens.
Rotate the right diopter adjustment for the clearest view on the
image intensifier screen.
(8) Adjust the eye relief distance by pressing the eye relief
adjustment (Figure 2-13) and sliding goggles fore or aft to obtain a
full field-of-view of the image. Reset the diopter adjustments for
best image.
NOTE
Any readjustment of eye relief requires resetting

the diopter adjustments.
(9) Adjust the objective lens focus (Figure 2-1) while

observing an object until the sharpest image is obtained.
2-72
WARNING

(10) To flip up, turn the power switch to the RESET/OFF

position, place an open hand under the goggles, grasp the goggles
and rotate up and rearward until the latch is firmly engaged.
(11) To flip down, grasp the goggles and rotate down and
forward until the latch is firmly engaged.
(12) Turn the power switch to the ON position to resume

viewing.
2-73
2-23 HAND-HELD OPERATION
CAUTION
Operate the goggles only under darkened

conditions or use the objective lens cap to cover
the objective lens for daylight conditions.
NOTE
When utilizing the NVG for driving purposes, the

NVG may not be used in the hand-held mode.
The goggles must be worn in the headmounted or
helmet mounted position.
(2) Turn the power switch to ON.

independently.
NOTE
The sharpest image will be observed only when

the objective lens and both eyepiece lenses are
properly focused.
(4) Hold the goggles with your left hand and fold the left
eyecup over the eyepiece lens with your thumb or forefinger to
obstruct view through the left eyepiece lens. Rotate the right
diopter adjustment for the clearest view of the image intensifier
screen.
2-74
(5) Hold the goggles with your right hand and fold the right
eyecup over the eyepiece lens with your right thumb or forefinger
to obstruct view through the right eyepiece lens. Rotate the left
diopter adjustment for the clearest view of the image intensifier
screen.
(6) Readjust the objective lens while observing an object

until the sharpest image is obtained.
2-24 OPERATION WITH COMPASS
CAUTION
You will get inaccurate readings when using the

compass on any headmount or helmet mount with
the magnet still installed. Only the magnet on the
metal mount can be removed without causing
damage to the equipment, see paragraph 2-10.
NOTE
• The compass reading is the magnetic North, not

true North.
• The compass reading is within 2° of correct

absolute magnetic bearing. Compass readings
with mounted goggles (headmount or helmet
mount) can be up to ±15° of correct absolute
magnetic bearing. This occurs mostly in the East
(90°) to West (270°) and less in the North (360°) to
South (180°) reading. If the compass is
inadvertently magnetized this could cause an
additional 15° error.
2-75
NOTE
The objective lens focus can be fine tuned after

installation, but in order to obtain an accurate
reading, the compass must be vertical. (The
compass image must be level.)
(1) Install compass per paragraph 2-10.
(2) If necessary to more clearly view your distant object,

adjust the objective lens focus slightly by gripping the compass
and turning clockwise.
WARNING
The compass illuminator can be seen by other

night vision users.
CAUTION
Increase brightness slowly. Excessive brightness

may burn a temporary image into the image
intensifier. Do not increase brightness any more
than is necessary to clearly read the compass
heading.
NOTE
The monocular must be focused at or near infinity

for proper compass operation.
(3) To view the compass through the goggles, grip the

compass with index finger on top and thumb on illumination button
at the bottom (Figure 2-1). Press button slightly with thumb until
proper brightness is obtained. The image should appear as shown
in Figure 2-29.
2-76
Figure 2-29. View through Installed Compass.
(4) The compass readings should change when you move

your head from side to side. Rotate or tap compass slightly to
ensure compass is operating correctly. Hold the goggles in a level
position to assure free rotation of the compass scale.
(5) The tick mark closest to the center of the light display is
the compass bearing. The tick marks are in degrees, with longer
tick marks every five degrees and bearing labels every 10 degrees.
2-77
2-25 IR SOURCE OPERATIONS
WARNING

devices.
CAUTION

NOTE
• The purpose of the IR source is for viewing at

close distances up to 3 meters when
additional illumination is needed.
• Some goggles are equipped with an

additional momentary IR function. For these
goggles, turn the power switch knob
clockwise (without pulling) past the ON
position. Observe that a red light appears in
the left eyepiece.
2-78
(1) Pull the power switch knob (Figure 2-1) out and rotate
clockwise to the IR position. With the goggles held to the eyes,
observe that a red light appears in the left eyepiece. This indicates
that the IR source is operating.
(2) Operation with IR Spot/Flood Lens:
(a) Pull the power switch knob (Figure 2-1) out and
rotate clockwise to the IR position. With the goggles held to the
eyes, turn the IR spot/flood lens until you have achieved the
optimum illumination for the desired distance.
(b) Turn the power switch counterclockwise to the ON

position. Observe that the red indicator disappears.
2-26 OPERATION WITH 3X MAGNIFIER
(1) Install 3X magnifier per paragraph 2-20.
NOTE
The mated 3X magnifier and objective lens will

turn as a unit to allow focusing.
(2) Grasp the 3X magnifier and focus while observing an

object until the sharpest image is obtained.
2-79
2-27 PREPARATION FOR STORAGE
(1) Shutdown. Perform the following procedures to shut

down the goggles.
(a) Turn the power switch to the OFF position.
(b) Remove the goggles from the headmount or helmet

mount (if so equipped) by depressing the latch lever (Figure 2-1)
and removing the goggles from the headmount or helmet mount
socket (Figure 2-13).
(2) Packaging After Use.
WARNING
Do not carry batteries in pockets containing metal

objects such as coins, keys, etc. Metal objects
can cause the batteries to short circuit and
become very hot.
(a) Unscrew battery cap and remove battery(ies).
(b) Inspect the battery compartment for corrosion or

moisture. Clean and dry if necessary.
(c) Replace the battery cap.
(d) Remove the demist shields, sacrificial window,

compass or 3X magnifier if installed. Install objective lens cap.
2-80
NOTE
• Prior to placing goggles into carrying case,

ensure goggles and case are free of dirt,
dust, and moisture.
• The goggles and helmet mount should not be

left on the helmet when the helmet is
removed.
(e) Properly position the pull tabs (carrying case

pockets) by sliding your finger into each pocket to tuck each tab
into place. (Old case only)
CAUTION
• Old helmet mount will not fit into the carrying

case, store in the shipping and storage case.
• Put the sacrificial window in the bottom left or

right corner of the carrying case accessory
pocket to prevent damage to the window.
(Old case only)
(f) Refer to Figure 1-1 for proper placement of demist

shields, batteries, carrying case strap, lens paper, sacrificial
window, manual, LIF, browpads, headmount, helmet mount and
compass.
(g) Place the goggles (objective lens down) into the

shallow pocket of the carrying case.
(h) Place the carrying case into the shipping and

storage case; close and latch. (Figure 1-1)
(i) Return to storage area.
2-81
Section V. Operation Under Unusual Conditions
2-28 OPERATION IN DUSTY OR SANDY AREAS
CAUTION
Operation in dusty or sandy areas can pit scratch

the optical elements and damage the mechanical
components unless the precautions given below
are observed.
(1) Ensure that the sacrificial window is in place over the

LIF.
(2) Avoid pointing the goggles into the wind unless

necessary for operation.
(3) Keep the carrying case closed unless removing or

replacing items.
(4) Ensure that all dust and sand is removed from the
goggles and carrying case after operation.
2-29 OPERATION IN RAINY OR HUMID CONDITIONS
CAUTION
Operation in rainy or humid conditions can cause

corrosion and deterioration of the goggles unless
the precautions given below are observed.
2-82
(1) Install the demist shields per paragraph 2-8.
(2) Keep the carrying case, and the shipping and storage
case closed unless removing or replacing items.
(3) Dry the goggles, mounts, and accessories after

exposure to rain or high humidity and before storage. This will
prevent mildew from forming in the case.
(4) Do NOT store goggles in a wet carrying case or a wet

shipping and storage case.
2-30 OPERATION IN SALT WATER AREAS
(1) After exposure to salt water, clean the NVG per

paragraph 3-2.
2-31 OPERATION IN NUCLEAR, BIOLOGICAL AND

CHEMICAL (NBC) ENVIRONMENTS
WARNING
Do not use contaminated eyecups. They

must be replaced.
(1) Decontamination – Wear a protective mask while using

goggles after decontamination process.
(2) Hardness – Do not use DS-2 for decontaminating the

NVG. To decontaminate, use 5% sodium hypochlorite and rinse
with hot (185°F) soapy water.
2-83
2-32 OPERATION IN LASER THREAT ENVIRONMENTS
NOTE
The LIF is a light protection filter. This filter must

be used at all times unless directed by the unit
commander, to remove the LIF based upon his/her
assessment of the laser threat in the theater. Use
of this filter will result in a slight reduction in
system gain.
Install the LIF as described in paragraph 2-11.
2-84
CHAPTER 3
MAINTENANCE INSTRUCTIONS
Section I. Lubrication Instructions
No lubrication is required.
Section II. Troubleshooting Procedures
3-1 TROUBLESHOOTING
Table 3-1 lists common malfunctions that you may find with your
equipment. Perform the test, inspections, and corrective actions in
the order they appear in the table.
This table cannot list all the malfunctions that may occur, all the
tests and inspections needed to find the fault, or all the corrective
actions needed to correct the fault. If the equipment malfunction is
not listed or actions listed do not correct the fault, notify your
maintainer.
3-1
3-2
Table 3-1. Operator’s Troubleshooting.
MALFUNCTION TEST OR INSPECTION CORRECTIVE ACTION
1. Goggles fail to Visual. Turn power switch to

activate. RESET/OFF position and
then ON.
Check for defective, missing or Replace batteries or install

improperly installed battery(ies). correctly.
If goggles still fail to

activate, refer to higher
level of maintenance.
2. IR source fails to In a dark location with system If IR source still fails to

activate. turned on, activate IR source. activate, refer to higher
Visually check IR source level of maintenance.
operation; scene should brighten.
3. IR source indicator fails Visual. Refer to higher level of

to activate. maintenance.
Table 3-1. Operator’s Troubleshooting - Continued.
4. Poor image quality. Check objective lens or eyepiece Refocus.

lens focus.
Check for fogging or dirt on Clean lens surfaces.

objective lens or eyepiece lens. If image quality is still poor,
refer to higher level of
maintenance.
5. Light visible around Check eye relief distance. Re-adjust for proper eye
eyecup. relief distance.
Check eyecup for resiliency. If eyecups defective, refer
to higher level of
maintenance.
6. Diopter adjustment Check to see if the diopter If damaged, refer to higher
cannot be made. adjustment is bent or broken. level of maintenance.
7. Interpupillary adjust- Defective eyepiece lens. Refer to higher level of

ment cannot be made maintenance.
3-3
(left and right eye).
3-4
8. Battery cap difficult to turn. Check for dirt or grit in Clean.

threads.
Visually inspect for the If o-ring is missing, refer to
presence of an o-ring higher level of
(Figure 2-8). maintenance.
Check for damaged battery If damaged, refer to higher

cap or threads on battery level of maintenance.
compartment.
9. Head straps cannot be Check for defective buckles, If damaged, refer to higher
tightened. fasteners or straps. level of maintenance.
10. Headmount or helmet mount Check socket or latch for Clean socket and latch.
socket and goggle latch does dirt.
not catch.
Check socket or latch for If damaged, return both
damage. headmount or helmet
mount and goggles to high-
er level of maintenance.
11. Helmet Mount will not Visual. If damaged, refer to higher

tighten to helmet. level of maintenance.
12. LIF will not thread or Check for dirt in threads. Clean threads.
obstruct view.
Check for damaged If damaged, refer to higher
assembly. level of maintenance.
13. IR spot/flood lens will not Visual. Refer to higher level of
adjust. maintenance.
14. Compass does not Visual. Refer to higher level of
illuminate. maintenance.
15. Compass will not stay on Visual. Refer to higher level of
the goggles. maintenance.
16. Compass display is not Visual. Make sure the goggles are
clear. focused for infinity. If so,
and compass display is still
not clear, refer to higher
3-5
level of maintenance.
3-6
17. Goggles do not cut off Visual. If damaged, refer to higher

when exposed to level of maintenance.
highlight.
Perform the following test
under daylight or bright
room light (not fluorescent
light).
Place the objective lens cap

on the objective lens. Turn
goggles ON and observe
that they cut off within
70 ±30 seconds after
energized.
Turn power switch to

RESET/OFF and then ON to
reenergize goggles.
Section III. Operator’s Maintenance Procedures
3-2 CLEANING THE NVG
CAUTION
• The goggles are a precision electro-optical

instrument and must be handled carefully.
• Do not scratch the external lens surfaces or

touch them with your fingers.
• Wiping demist shields with lens paper while

wet or with wet lens paper can damage the
coating.
Clean goggles with water if necessary and dry thoroughly. Clean

lenses with lens paper (and water if necessary, except for demist
shields). Demist shields must be dry before being cleaned with dry
lens paper.
3-3 HEADMOUNT MAINTENANCE
(1) Browpad Replacement. Replace the browpad when

cracked, torn, or contaminated.
3-7
(a) Firmly grasp the headmount and remove the old
browpad.
(b) Gently press on the new browpad. Lightly smooth

out any wrinkles in the new browpad.
(2) Neck Pad Reinstallation. During operation of the

goggles, it is possible for the neck pad to become separated from
its position on the headband. Perform the following procedure to
reinstall the neck pad.
(a) Lift the upper strap retention tab (see Figure 3-1)
allowing the neck pad strap to be inserted underneath.
(b) Slip the neck pad strap all the way under the upper
strap retention tab and then pull the lower part of the neck pad
strap under the lower strap retention tab.
(c) Repeat steps (a) and (b) for the other side of the
headband and neck pad if necessary.
3-8
Figure 3-1. Reinstalling the Neck Pad.
(3) Threading the Sliding Bar Buckles. While donning

and adjusting the headmount, it is possible for a strap to slip out of
a slide fastener. If necessary, reinstall as follows:
(a) Thread the strap from the inside of the buckle over
the moveable sliding bar (see Figure 3-2). Thread the strap back
through the buckle but this time under the moveable sliding bar
and over the serrated part of the buckle.
3-9
Figure 3-2. Threading the Sliding Bar Buckles.
(b) Pull the strap through the buckle and tighten as
necessary.
(c) Repeat steps (a) and (b) for any other straps and
buckles that may have come undone.
3-4 NECK CORD MAINTENANCE

The neck cord (Figure 1-1) may be broken, frayed, or loose at one
or both ends.
If loose, re-tie cord. If broken or severely frayed, replace cord as

follows:
(1) Insert ends through rear cover plate holes from the rear.
(2) Thread right cord end through hole in objective lens cap.
(3) Tie a knot in each end.
3-10
APPENDIX A
REFERENCES
A-1 SCOPE
This appendix lists all the forms, field manuals, technical manuals,
and miscellaneous publications referred to in this manual.
A-2 FORMS
Inspection and Maintenance Record DA 2404
Product Quality Deficiency Report SF 368
Recommended Changes to DA 2028

Publications and Blank Forms
A-3 FIELD MANUALS
First Aid for Soldiers FM 21-11
A-4 TECHNICAL MANUALS
Operator’s and Unit Maintenance TM 11-5855-299-12&P

Manual (including Repair Parts and
Special Tools List) for Test Set,
Electronic Systems, TS-4348/UV
Procedures for Destruction of TM 750-244-2

Electronic Materiel to Prevent
Enemy Use (Electronics Command)
A-1
APPENDIX A
REFERENCES - Continued
A-5 MISCELLANEOUS PUBLICATIONS
Army Medical Department CTA 8-100

Expendable/Durable Items
Consolidated Index of Army DA Pam 25-30

Publications and Blank Forms
Expendable/Durable Items (Except CTA 50-970

Medical, Class V Repair Parts, and
Heraldic Items)
The Army Maintenance Management DA Pam 738-750

System (TAMMS)
A-6 MARINE CORPS USE

Equipment Record Procedures TM 4700-15/1
Marine Corp Publication Distribution MCPDS

System
Recommended Changes to NAVMC 10772

Publications/Logistics-Maintenance
Data Coding
A-7 AIR FORCE USE

Quality Deficiency Report 00-35D-34
General Shop Practice Requirement 00-25-234
Maintenance and Recoverability Coding 00-25-195
A-2
APPENDIX B
COMPONENTS OF END ITEM (COEI) AND
BASIC ISSUE ITEMS (BII) LISTS
INTRODUCTION
B-1 SCOPE
This appendix lists COEI and BII for the AN/PVS-7B and AN/PVS-
7D to help you inventory items for safe and efficient operation of
the equipment.
B-2 GENERAL
The COEI and BII information is divided into the following lists.
Components of End Item (COEI). This list is for information

purposes only and is not authority to requisition replacements.
These items are part of the AN/PVS-7B and AN/PVS-7D. As part
of the end item, these items must be with the end item whenever it
is issued or transferred between property accounts. Items of COEI
are removed and separately packaged for transportation or
shipment only when necessary. Illustrations are furnished to help
you find and identify the items.
Basic Issue Items (BII). These essential items are required to

place the AN/PVS-7B and AN/PVS-7D in operation, operate it, and
to do emergency repairs. Although shipped separately packaged,
BII must be with the AN/PVS-7B and AN/PVS-7D during operation
and when it is transferred between property accounts. Listing
these items is your authority to request/requisition them for
replacement based on authorization of the end item by the
TOE/MTOE. Illustrations are furnished to help you identify the
items.
B-1
B-3 EXPLANATION OF COLUMNS IN THE COEI LIST
AND BII LIST
Column (1), Illus Number. Gives you the number of the item
illustrated.
Column (2), National Stock Number (NSN). Identifies the stock

number of the item to be used for requisitioning purposes.
Column (3), Description CAGEC, and Part Number. Identifies the

Federal item name (in all capital letters) followed by a minimum
description when needed. The stowage location of COEI and BII is
also included in this column. The last line below the description is
the CAGEC (commercial and Government entity code) (in
parenthesis) and the part number.
Column (4), Usable On Code. When applicable, gives you a code

if the item you need is not the same for different models of
equipment.
Code Used on
HKG AN/PVS-7B
LDF AN/PVS-7D
Column (5), Unit of Measure (U/M). Indicates how the item is

issued for the National Stock Number shown in column (2).
Column (6), Qty Rqr. Indicates the quantity required.
Supply System Responsibility. (Marine Corps Only) A list of

items that are furnished with and must be turned in with the end
item. Any item requiring replacement is the responsibility of the
holding organization or using unit.
B-2
Collateral Material. (Marine Corps Only) A list of items that are
supplied with the initial issue of an end item and also retained by
the unit.
5th Echelon Rehabilitation Program. (Marine Corps Only) Major

items returned under this program will be evacuated under the
provision(s) of the applicable Marine Corps Order(s) with items
listed under “Supply System Responsibility” rebuild and
replacement under the 5th Echelon Rehabilitation Program will be
limited to these items only. Those items under the heading
Collateral Material and using unit items shall be held by holding
organizations/using units for application to replacement end items.
B-3
Components of End Item
(Marine Corps Supply System Responsibility)
Figure B-1. Components of End Item (Sheet 1 of 2).
B-4
Figure B-1. Components of End Item (Sheet 2 of 2).
B-5
B-6
Table 1. Components of End Item List.
(1) (2) (3) (4) (5) (6)

NATIONAL USABLE
ILLUS STOCK DESCRIPTION, CAGEC, ON QTY
NUMBER NUMBER AND PART NUMBER CODE U/M RQR
1 GOGGLE ASSEMBLY EA 1
(80063) A3144261-1 HKG
1 GOGGLE ASSEMBLY LDF EA 1

(80063) A3144261-2
2 5855-01-246-8271 WINDOW, SACRIFICIAL EA 1

(80063) A3144264
3 5855-01-246-8272 DEMIST SHIELD ASSY EA 2

(80063) A3144263
4 5855-01-379-1410 FILTER, INFRARED LIGHT EA 1

(54490) 5009737
Table 1. Components of End Item List - Continued.
(1) (2) (3) (4) (5) (6)

NATIONAL USABLE
5 5855-01-246-8266 HEADSET ASSEMBLY EA 1

(80063) A3144268
6 5855-01-355-8599 BROWPAD ASSY, THIN EA 1

(80063) A3144280
7 5855-01-355-8600 BROWPAD ASSY, MEDIUM EA 1

(80063) A3144435
8 5855-01-297-7847 BROWPAD ASSY, THICK EA 1

(80063) A3144436
9 5855-01-381-6052 COMPASS ASSEMBLY LDF EA 1

(80063) A3187430
10 5340-01-451-7737 CLIP, RETAINING LDF EA 1

(80063) A3260933
B-7
B-8
(1) (2) (3) (4) (5) (6)

NATIONAL USABLE
11 5855-01-457-2953 MOUNT, VIEWER LDF EA 1

(80063) A3256368
or
11 5855-01-441-0401 MOUNT, VIEWER HKG EA 1
(80063) A3260927
12 5855-01-382-5169 LENS ASSEMBLY, FOCUS LDF EA 1

(80063) A3187441
13 5855-01-246-8269 CASE, CARRYING (OLD) HKG EA 1

(80063) A3144262
13 5855-01-398-4284 CASE, INFRARED EQUIP EA 1

(NEW)
(80063) A3187392
14 5855-01-250-2431 STRAPPING EA 1
(80063) A3144267
(1) (2) (3) (4) (5) (6)

NATIONAL USABLE
15 5855-01-397-6608 CAP, PROTECTIVE, DUST EA 1

(80063) A3144318
16 4020-01-446-8097 CORD, FIBROUS EA 1

(80063) A3144306
17 OPERATOR’S MANUAL EA 1
TM 11-5855-262-10-2
18 5855-01-246-6805 CASE, SHIPPING HKG EA 1

(80063) A3144257
18 CASE, EA 1
SHIPPING/STORAGE
(80063) A3264350
B-9
Basic Issue Items
Not Applicable
B-10
APPENDIX C
ADDITIONAL AUTHORIZATION LIST (AAL)
INTRODUCTION
C-1 SCOPE
This appendix lists additional items you are authorized for the
support of the AN/PVS-7B and AN/PVS-7D.
C-2 GENERAL
This list identifies items that do not have to accompany the

AN/PVS-7B and AN/PVS-7D and that do not have to be turned in
with it. These items are all authorized to you by CTA, MTOE, TDA,
or JTA.
C-3 EXPLANATION OF COLUMNS IN THE AAL
Column (1), National Stock Number (NSN). Identifies the stock

number of the item to be used for requisitioning purposes.
Column (2), Description, Commercial and Government Entity Code

(CAGEC), and Part Number (P/N). Identifies the Federal item
name (in all capital letters) followed by a minimum description
when needed. The last line below the description is the CAGEC
(in parentheses) and the part number.
Column (3), Usable On Code. When applicable, gives you a code

if the item you need is not the same for different models of
equipment.
Code Used on
HKG AN/PVS-7B
LDF AN/PVS-7D
C-1
Column (4), Unit of Measure (U/M). Indicates how the item is
issued for the National Stock Number shown in column (1).
Column (5), Qty Recm. Indicates the quantity recommended.
Using Unit Responsibility. (Marine Corps Only) A list, in

alphabetical sequence, of items that will not be issued with the end
item. They must be requisitioned, as required, through the supply
system by the holding organization or the using unit.
C-2
Table 1. Additional Authorization List.
(Marine Corps Using Unit Responsibility)
(1) (2) (3) (4) (5)

NATIONAL USABLE
STOCK DESCRIPTION, CAGEC, ON QTY
NUMBER AND PART NUMBER CODE U/M RECM
6135-01-090-5365 BATTERY, NON- EA 1

RECHARGEABLE
(80058) BA-5567/U
6135-00-985-7845 BATTERY, NON- EA 2

RECHARGEABLE
(80058) BA-3058/U
6135-01-333-6101 BATTERY, NON- EA 2

RECHARGEABLE
(83740) L91
6625-01-323-9584 TEST SET, ELECTRONIC EA 1

TS-4348/UV
(80063) A3139775
5855-01-381-6052 COMPASS ASSEMBLY HKG EA 1
C-3
(80063) A3187430
C-4
Table 1. Additional Authorization List - Continued.
(1) (2) (3) (4) (5)

NATIONAL USABLE
STOCK DESCRIPTION, CAGEC, ON QTY
NUMBER AND PART NUMBER CODE U/M RECM
5855-01-382-5169 LENS ASSEMBLY, FOCUS HKG EA 1

(80063) A3187441
5855-01-441-0401 MOUNT, VIEWER HKG EA 1

(80063) A3260927
5340-01-451-7737 CLIP, RETAINING HKG EA 1

(80063) A3260933
5855-01-423-0817 MAGNIFIER LENS EA 1

ASSEMBLY
(80063) A3256391
APPENDIX D
EXPENDABLE AND DURABLE ITEMS LIST
INTRODUCTION
D-1 SCOPE
This appendix lists expendable and durable items that you will
need to operate and maintain the AN/PVS-7B and AN/PVS-7D.
This list is for information only and is not authority to requisition the
listed items. These items are authorized to you by CTA 50-970,
Expendable/Durable Items (Except Medical, Class V Repair Parts,
and Heraldic Items), or CTA 8-100, Army Medical Department
Expendable/Durable Items.
D-2 EXPLANATION OF COLUMNS IN THE

EXPENDABLE/DURABLE ITEMS LIST
Column (1) - Item Number. This number is assigned to the entry in
the list and is referenced in the narrative instructions to identify the
item (e.g. “Use lubricating oil, item 25, Appendix D”).
Column (2) - Level. This column includes the lowest level of

maintenance that requires the listed item (C =Operator/Crew).
Column (3) - National Stock Number. This is the NSN assigned to

the item, which you can use to requisition it.
Column (4) – Item Name, Description, Commercial and

Government Entity Code (CAGEC), and Part Number (P/N). This
column provides the other information you need to identify the
item.
Column (5) - Unit of Measure (U/M). This code shows the physical
measurement or count of an item, such as gallon, dozen, gross,
etc.
D-1
D-2
Table 1. Expendable and Durable Items List.
(1) (2) (3) (4) (5)
NATIONAL
ITEM STOCK ITEM NAME, DESCRIPTION,
NUMBER LEVEL NUMBER CAGE, PART NUMBER U/M
1 C 6640-01-459-4239 PAPER, LENS PK

(81348) A-A-50177, TYPE I, CLASS 5
SUBJECT INDEX
Para
Abbreviations, list of .................................................................. 1-8

Additional Authorization List, Section II (Table)..........................C-1
Adjustment (See specific adjustment.)
Ambient light ............................................................................. 1-1
Appendices
A – References ...................................................................A-1
B – Components of End Item List and Basic Issue
Items List .......................................................................B-1
C – Additional Authorization List..........................................C-1
D – Expendable and Durable Items List ..............................D-1
Assembly and preparation for use ............................................. 2-5
Automatic shutoff..................................................................... 1-16
Basic issue items....................................................................... B-1

Battery
AA size..................................................................... 1-13, 1-16
Alkaline .................................................................... 1-13, 1-16
Installing.............................................................................. 2-6
Life............................................................................. 1-16, 2-6
Lithium ..................................................................... 1-13, 1-16
Low-battery indicator......................................... 1-10, 1-16, 2-1
Replacing............................................................................ 2-6
Voltage.............................................................................. 1-16
Black spots......................................................................... 1-9, 2-4
Bright spots ........................................................................ 1-9, 2-4
Browpads .................................................................................. 1-9
Index-1
SUBJECT INDEX - Continued.
Para
Capabilities and features ......................................................... 1-10

Case
Carrying ............................................................................ 1-11
Shipping and Storage........................................................ 1-11
Caution...................................................................................... 1-9
Characteristics......................................................................... 1-10
Checks, preventive maintenance ............................................... 2-2
Chicken wire....................................................................... 1-9, 2-4
Cleaning .................................................................................... 3-2
Compass
Description ................................................................. 1-11, 2-1
Installation......................................................................... 2-10
Operation .......................................................................... 2-24
Components of End Item List.....................................................B-1
Corrosion prevention and control ............................................... 1-3
Cross-reference list, nomenclature ............................................ 1-7
Current .................................................................................... 1-13
DA Pam 738-750 ....................................................................... 1-3

Dark (or darkened area) ............................................................ 1-9
Data.........................................................................................1-13
Electrical .................................................................. 1-13, 1-16
Environmental ................................................................... 1-13
Equipment......................................................................... 1-13
Mechanical............................................................... 1-13, 1-14
Optical...................................................................... 1-13, 1-15
Index-2
Para
Demist Shields
Description ........................................................................ 1-11
Installation........................................................................... 2-8
Description and use of operator’s controls
and indicators...................................................................... 2-1
Destruction of Army materiel to prevent enemy use................... 1-4
Difference between models ..................................................... 1-12
Diopter ...................................................................................... 1-9
Diopter Adjustment .................................................................... 2-1
Dusty conditions ...................................................................... 2-28
Edge glow .......................................................................... 1-9, 2-4

Electrical
Current.............................................................................. 1-13
Function ............................................................................ 1-16
Voltage.............................................................................. 1-13
Electronic circuit function ......................................................... 1-16
Equipment
Characteristics, capabilities, and features ......................... 1-10
Data .................................................................................. 1-13
Improvement recommendations .......................................... 1-5
Expendable and Durable Items List ...........................................D-1
Eyecups, installation.................................................................. 2-7
Index-3
Para
Eyepiece lens
Focus ................................................................................ 1-13
Operation ............................................................................ 2-1
Range ............................................................................... 1-13
Features .................................................................................. 1-10

Field-of-view ............................................................................ 1-13
Filter (see LIF)
Fixed-pattern noise............................................................. 1-9, 2-4
Flashing.............................................................................. 1-9, 2-4
Flickering ............................................................................ 1-9, 2-4
Focus
Eyepiece (see Eyepiece lens)
Objective (see Objective lens)
General information ................................................................... 1-1

Glossary .................................................................................... 1-9
Goggle .................................................................................... 1-11
Hand-held operation ................................................................ 2-23

Headmount
Installation.......................................................... 2-13 thru 2-15
Maintenance ....................................................................... 3-3
Operation .......................................................................... 2-21
Index-4
Para
Helmet Mount
Installation.......................................................... 2-16 thru 2-19
Operations ........................................................................ 2-22
Highlight Cutoff........................................................ 1-9, 1-10, 1-16
Honeycomb (see Fixed-pattern noise)
Humid conditions..................................................................... 2-29
I, J, K
Illumination required ................................................................ 1-13

Image intensifier operation ...................................................... 1-15
Inspection
Criteria for proper image intensifier operation
(see image intensifier operation).................................. 2-4
Preventive maintenance...................................................... 2-2
Intermittent operation................................................................. 2-4
Interpupillary distance....................................................... 1-13, 2-1
IR source operations ............................................................... 2-25
IR Spot/Flood Lens
Description ........................................................................ 1-11
Installation......................................................................... 2-12
Operation ............................................................................ 2-1
Index-5
Para
Laser threat environments ....................................................... 2-32

Latch ......................................................................................... 2-1
LIF .......................................................................................... 2-11
Description ................................................................. 1-9, 1-11
Installation......................................................................... 2-11
List of abbreviations................................................................... 1-8
Lithium battery (see Battery)
Location and description of major components ........................ 1-11
Low-battery indicator
Description ........................................................ 1-10, 1-16, 2-1
Operation .......................................................... 1-10, 1-16, 2-1
Lubrication....................................................... Chapter 3, Section1
Magnification ........................................................................... 1-13

Magnifier, 3X
Installation......................................................................... 2-20
Operation .......................................................................... 2-26
Maintenance
Cleaning the NVG ............................................................... 3-2
Forms and procedures ........................................................ 1-2
Headmount ......................................................................... 3-3
Neckcord............................................................................. 3-4
Mechanical data ...................................................................... 1-13
Mechanical functions ............................................................... 1-14
Index-6
Para
NBC environments .................................................................. 2-31

Neck cord ........................................................................... 2-2, 3-4
Nomenclature cross-reference list ............................................. 1-7
Objective lens
Check ................................................................................. 2-2
Focus................................................................................ 1-13
Function ............................................................................ 1-15
Location ............................................................................ 1-11
Operating temperature ............................................................ 1-13
Operator adjustment limits....................................................... 1-13
Operator controls and indicators................................................ 2-1
Optical
Data .................................................................................. 1-13
Functions .......................................................................... 1-15
PMCS........................................................................................ 2-2
Power
Source ..................................................................... 1-13, 1-16
Switch ................................................................................. 2-1
Preparation for storage ............................................................ 2-27
Purpose of equipment ...................................................... 1-1, 1-10
Index-7
Para
Rainy conditions ...................................................................... 2-29

Reference list ............................................................................ 1-7
References ................................................................................A-1
Reporting Equipment Improvement
Recommendations ............................................................. 1-5
Resolution check using theTS-4348/UV Test Set.......................2-3
Sacrificial Window
Description ................................................................. 1-9, 1-11
Installation........................................................................... 2-9
Salt water areas....................................................................... 2-30
Sandy conditions ..................................................................... 2-28
Scintillation ................................................................................ 1-9
Scope ........................................................................................ 1-1
Shading .............................................................................. 1-9, 2-4
Shipping and Storage case......................................................1-11
Shutdown (see Preparation for storage)
Standard Form 368............................................................. 1-3, 1-5
Storage temperature................................................................ 1-13
Index-8
Para
3X Magnifier
Installation......................................................................... 2-20
Operation .......................................................................... 2-26
Temperature limits................................................................... 1-13
Test Set, TS-4348/UV ............................................................... 2-3
Troubleshooting......................................................................... 3-1
U, V
Unpacking ................................................................................. 2-5

Vertical Adjustment Operation ................................................. 2-21
Voltage.................................................................................... 1-16
W, X, Y, Z
Warning..................................................................................... 1-9
Warranty Information ................................................................. 1-6
Weight
Goggle .............................................................................. 1-13
Shipping and storage case ................................................ 1-13
Index-9/10 blank
JOEL B. HUDSON
RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
( FROM: (PRINT YOUR UNIT'S COMPLETE ADDRESS)
DATE SENT
I
PUBLICATION NUMBER PUBLICATION DATE PUBLICATION TITLE
BE EXACT PIN·POINT WHERE IT IS

PAGE PARA- FIGURE TABLE
NO. GRAPH NO. NO.
PRINTED NAME, GRADE OR TITLE AND TELEPHONE NUMBER SIGN HERE
PREVIOUS EDITIONS P.S.--IF YOUR OUTFIT WANTS TO KNOW ABOUT YOUR

DA 1~~~~9 2028-2 ARE OBSOLETE. RECOMMENDATION MAKE A CARBON COPY OF THIS
AND GIVE IT TO YOUR HEADQUARTERS.
THE METRIC SYSTEM AND EQUIVALENTS
PIN: 064249-000

TM 11 5855 262 10 2 NVG Anpvs 7b

Uploaded by

Copyright:

Available Formats

TM 11 5855 262 10 2 NVG Anpvs 7b

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TM 11 5855 262 10 2 NVG Anpvs 7b

Uploaded by

Copyright:

Available Formats

What safety precautions should be taken when using Night Vision Goggles?

What safety precautions should be taken when using Night Vision Goggles?

What are some limitations of using Night Vision Goggles?

What are some limitations of using Night Vision Goggles?

ARMY TM 11-5855-262-10-2

MARINE CORPS TM 09500A-10/1A

AN/PVS-7B Image Intensifier

DISTRIBUTION STATEMENT C - Distribution authorized to U.S. Government

DESTRUCTION NOTICE - For unclassified, limited documents, destroy by any

DEPARTMENTS OF THE ARMY, HEADQUARTERS,

• Do not carry batteries in pockets containing

The image intensifier’s phosphor screen contains

• If the phosphor screen material contacts your

• If you inhale/swallow any phosphor screen

The compass illuminator can be seen by other

It is critical that the goggles be turned off manually

When installing the headmount over the protective

The IR source is a light that is invisible to the

Do not use contaminated eyecups. They must be

To avoid physical and equipment damage when using the Night

• The NVG requires some night light

• Night light is reduced by passing cloud cover,

• The NVG is less effective viewing into

• The NVG is less effective through rain, fog,

• The NVG will not “see” through dense smoke.

• Adjust vehicular speed to prevent overdriving

REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS

*This manual supersedes TM 11-5855-262-10-2 dated 1 December 1997

Para. No. Title Page

CHAPTER 1 INTRODUCTION .......................................... 1-1

Section I General Information ......................................... 1-1

Section II Equipment Description .................................... 1-9

Section III Principles of Operation .................................... 1-21

Para. No. Title Page

CHAPTER 2 .................................................................... 2-1

Section I Description and Use of Operator’s

Section II Prevention Maintenance Checks

Section III Assembly and Preparation for Use................... 2-33

Para. No. Title Page

2-14 Installation of Headmount with

Section IV Operating Procedures .................................... 2-65

Para. No. Title Page

Section V Operation Under Unusual Conditions............... 2-81

CHAPTER 3 MAINTENANCE INSTRUCTIONS............... 3-1

Section I Lubrication Instructions .................................... 3-1

Section II Troubleshooting Procedures ............................ 3-1

Section III Operator’s Maintenance Procedures................ 3-7

APPENDIX A References .................................... A-1

APPENDIX B Components of End Item (COEI)

APPENDIX C Additional Authorization List

APPENDIX D Expendable and Durable Items

ALPHABETICAL INDEX .................................................... Index-1

You must familiarize yourself with the entire manual before

The table of contents includes the paragraph number, title, and

A locator is provided on the right-hand border of the front cover.

Section I. General Information

This manual provides operation and maintenance instructions for

1-2 MAINTENANCE FORMS AND PROCEDURES

Department of the Army and procedures used for equipment