Scribd
Upload
128 views3 pages

Transmission Line Concepts

1. This document discusses voltage standing wave ratio (SWR) and return loss on transmission lines. SWR is defined as the ratio of maximum to minimum voltage on the line. Return loss is defined as the ratio of power reflected to power incident. 2. The Smith Chart is introduced as a way to plot the reflection coefficient G and convert between G and the normalized impedance z. It allows determining z given G at any point on the transmission line. 3. An open circuit termination is used as an example to illustrate how the Smith Chart works by plotting the reflection coefficient G for that case.

Uploaded by

sachin b
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
128 views3 pages

Transmission Line Concepts

1. This document discusses voltage standing wave ratio (SWR) and return loss on transmission lines. SWR is defined as the ratio of maximum to minimum voltage on the line. Return loss is defined as the ratio of power reflected to power incident. 2. The Smith Chart is introduced as a way to plot the reflection coefficient G and convert between G and the normalized impedance z. It allows determining z given G at any point on the transmission line. 3. An open circuit termination is used as an example to illustrate how the Smith Chart works by plotting the reflection coefficient G for that case.

Uploaded by

sachin b
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

1

G
1+G
q
Now consider what happens if we move a distance -z along the transmission line (in
the -z
direction, away from the load and toward the generator). At this point we have
V(d) = 1+G(z) = 1+GL e-j2bz = 1+|G| ej(q-2bz), shown in vector form below left.
q-2 bz
1
G
1+ G
1
vmin
vmax
q-2 bz
G
1+ G
If we inspect what happens to V(z) as we vary z, we can see from the figure below
right that
V(z) varies from a maximum of 1+|GL| to a minimum of 1-|GL|, and that the distance
between
minima or between maxima is 2bz = 2p, which occurs every l/2. Also, the distance
from a
minimum to a maximum is l/4.
This particular form of polar presentation has the advantage of containing all
possible values of G
within the circle |G| = 1, and the vector G is defined everywhere on a lossless
transmission line
by the same vector length |G| or r, with the distance to the load in wavelengths
identified with
the angle of the vector G.
Standing Wave Ratio (SWR) and Return Loss
We can identify the maximum and minimum voltages vmax and vmin (normalized to V+)
by
inspection of the figure above.
The ratio of these magnitudes is a real number, the voltage standing wave ratio
(SWR, or
VSWR), given by
EEE 194 RF TL Waves & Impedances
- 10 -
SWR =
vmax
vmin
=
1+|GL|
1-|GL| =
1+r
1-r
. Note that this can be solved for r, yielding
r =
SWR-1
SWR+1 , so if we know SWR we know r.
For a matched load r=0, SWR =1 and the voltage on the line is just V(d) = V+ for
all d; under
such a condition the line is termed flat.. The ratio of the power in the reflected
wave to that in
the incident wave, termed the return loss, is
PP+
=
|V-|2
|V+|2 = r2
or, expressed as a loss (a positive number) in dB
RL = -10 log10 r2 = -20 log10 r.
By measuring the return loss in dB, we can determine
r = 10RL/20 and SWR =
1+r
1-r
, which characterizes the degree of impedance match.
In a lossless network, the transmitted power is
Pt = P+ - P- = P+(1-r2), and the transmission loss TL is
TL = -10 log10 (1-r2) dB.
At the points of voltage minima and maxima, the impedance is a pure resistance,
which makes it
possible to evaluate Z at those points in terms of the standing wave ratio SWR.
At a voltage minimum (which is also a current maximum), Z = R = Zo and
Z =
Zo
SWR , a real quantity.
At a voltage maximum (a current minimum), Z = R = Zo and
Z = Zo x SWR, also a real quantity.
EEE 194 RF TL Waves & Impedances
- 11 -
The Smith Chart3
For a transmission line of characteristic impedance Zo and load impedance ZL the
reflection
coefficient GL is
GL =
ZL-Zo
ZL+Zo
=
ZL
Zo
- 1
ZL
Zo
+ 1
; normalize ZL to Zo by defining zL such that
zL =
ZL
Zo
. Substituting, we have
GL =
zL-1
zL+1 , and at any distance d from the load we have
G(d) = GLe-2jbd =
z(d)-1
z(d)+1 ,
where z = r+jx, the impedance, resistance and reactance normalized to Zo.
Solving for z, we have the value of z for any measured G at any point d
z(d) =
1+G(d)
1-G(d) . This can be expressed in the very useful form
Zin = Zo
ZL + jZotanbd
Zo + jZLtanbd, the input impedance of a line of length d, Zo and load ZL.
If we plot G on the polar plot, and overlay the circles of constant r and x, this
yields the Smith
Chart, on which we can convert from G to Z (or the reverse) by inspection.
To see how the Smith Chart works, first consider a matched load, Z = Zo and G = 0.
This
point is at the origin of the plot, since G = 0 +j0. This is plotted below left.
Next, consider a transmission line terminated with an open circuit at d=0.
3 Smith, P. H., "Transmission line calculator", Electronics, vol. 12, pg. 29, Jan.
1939 and "An improved
transmission-line calculator", Electronics, vol. 17, pg. 130, Jan. 1944; for an
interesting biography of
P. H. Smith see also http://www.noblepub.com/Noble/Smthbiog.html
EEE 194 RF TL Waves & Impedances
- 12 -
Zo Z(d)

You might also like