Scribd
Upload
204 views2 pages

Electronic Symbols

The document lists electronic component symbols and their abbreviations that are commonly used in laptop schematics. There are over 50 symbols listed along with their abbreviations covering things like power sources, connectors, controllers, sensors and more.

Uploaded by

Elmir Bolić
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
204 views2 pages

Electronic Symbols

The document lists electronic component symbols and their abbreviations that are commonly used in laptop schematics. There are over 50 symbols listed along with their abbreviations covering things like power sources, connectors, controllers, sensors and more.

Uploaded by

Elmir Bolić
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Electronic Symbols Abbreviation In Laptop Schematic

AC: Alternating current DOCK: DOCKING SOCKET

ACDRV: AC adapter to system-switch driver output EC: Embedded Controller

ACEDET: Adaptor Current Detector EC_ON: Embedded Controller Enable

ACGOOD: Valid adapter active-low detect logic open-drain EMI: Electromagnetic Interference (GANGGUAN
output ELEKTROMAGNETIK)

ACLN: Adaptor Current sensor Input EN: ENABLE

ACN: Adapter current sensor resistor ENTRIP: Enable Terminal

ACOP: Input Over-Power Protection F: FUSE

ACOV: Input Overvoltage Protection FSEL: Frequency Select Input

ACP: Adapter current sense resistor, positive input. GATE: Trigger gate

ADP+: Adapter Positive Supply GND: Ground

ADP_ID: Adapter Identity GP: GROUND PIN.

AGND: Analog Ground GPI: General Power Input

ALWP: ALWAYS POWER ON GPIO: General Power Input Output

B+: AC OR BAT POWER RAIL FOR POWER CIRCUIT HDMI: High-Definition Multimedia Interface

BATT: Battery ID: Continuous Drain Current

BAT+: BAT POWER RAIL FOR POWER CIRCUIT IDM: Pulsed Drain Current

BAT_DRV: Bat Fe Gate Driver ILN: Operating Supply Current

BAT_V: Battery Voltage ILN (SHDN): Shutdown Supply Current

BOM: BILL OF MATERIAL MANAGEMENT ILN (STBY): Standby Supply Current

BT: BUTTON IS: Continuous Source Current (Diode Conduction)

BT-EN: Bluetooth Enable IVIN: Battery Supply Current at VIN pin

BUZER: Connected JP: JUMPER POINT

BYP: Bay pass KBC: Keyboard Controller

CHGEN: Charge enables active-low logic input UVLO: Input Under voltage Lock Out

CIN: Input Capacitor LC DV: LCD POWER

CLK_EN: CLKOCK ENABLE V: RAIL (POWER)

CN: CONECTOR LDO: Linear Driver Output

CRT: Cathode ray tube V+: Positive Voltage

CSIN: Current Sensor input Negative LGATE: Lower-side MOSF ET gate signal

CSIP: Current Sensor input Positive VADJ: Output regulation voltage

DC: Direct current LPC: Low Pin Count

DM: DIM DIM SOCKET SOKET MEMORY SOKET DDR VALW: ALWAYS ON POWER
LVDS: Low-voltage differential signaling (SYSTEM VALWP VS+: SUPPORT VOLTAGE POSITIF
VALW PAD PENSIGNALAN)
THRM: THERMAL SENSOR
VBAT: BATTERY POWER
V SB: SOWER SWITCH BUTTON
MBAT: MAIN BATTERY
TMDS: Transition Minimized Differential Signaling
VCCP: Power chip (ich graphic chips) (TRANSMISI DATA TEKNOLOGY)

NB: North Bridge VSS: Signal ground

VCORE: POWER PROCESOR VSW: POWER SWICT

ODD: OUTPUT DISC DRIVE TP: TES POINT

VDD: Control power supply VTT: Memory Termination Voltage

PCI: Penpheral Component Interconnect TPAD: THERMAL PAD

VDDR: VDS DOWER DDR (VDRAMNRAMNMEM) VTERM: Memory Termination Voltage

VDS: VOLTAGE DRAM SOURCE VUSB: POWER USB

PGOOD: Power good open-drain output VGA: POWER VGA (VGPXNGPUNCVOD)

VFB: Feedback inputs Power VGFX: POWER GRAPHIC CHI

PIR: PRODUCT IMPROVED RECORD VREF: VOLTAGE REFERENCES

VG S: VOLTAGE GATE SOURCES

PSI#: Current indicator input

VIN: Input Voltage Range CN =Connector


PVC C: IC power positive supply D =Diode
VIN: ADAPTER POWER SUPLAY (vol_in) R =Resistor
RSMR ST: Resume Reset C =Capacitor
VL: Power Lock U = (chip) IC
R TC: REAL TIME CLOCK XIY = Crystal
VL: voltage across the load/Tegangan beban resistor UIQ = Mosfet
SB: South Bridge L = Coil
VL: Voltage Linear H = Hole
SHDN: Shutdown PAD = (pad)
VLDOIN: Power supply of the VTT and VTTREF output SW = switch
stage (to power MOS)
PQ = Power Mosfet Big
SYS_SDN: System Shutdown
PD = Power Diode
VOT: Volt_out
PU = Power IC
SPI: Serial Peripheral Interface
PR = Power Resistor
VRAM: Power memory
PC = Power Capacitor
VREF: POWER REFERENCES/SCHEMA
REFERENCE/PERMINTAAN SKEMA PL = Power Coil

VS: SUITCH POWER

TD: Death Time

You might also like