Scribd Logo
Upload

Welcome to Scribd!

  • 134 views

    ARL-500 2-Floor Lifts With Encoder Car Positioning - en PDF

    Uploaded by

    Henri Kleine
    This document provides instructions for operating a 2-floor lift using an ARL-500 encoder counter system. It involves mounting an additional door zone magnet between the two floors, setting the ARL-500 menu to detect 3 floors instead of 2, and adjusting the floor settings of related components to also detect 3 floors instead of 2. This allows the lift to function properly while stopping at two floor levels using the encoder counter system to simulate a third floor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    ARL-500 2-Floor Lifts With Encoder Car Positioning - en PDF

    Uploaded by

    Henri Kleine
    134 views1 page
    This document provides instructions for operating a 2-floor lift using an ARL-500 encoder counter system. It involves mounting an additional door zone magnet between the two floors, setting the ARL-500 menu to detect 3 floors instead of 2, and adjusting the floor settings of related components to also detect 3 floors instead of 2. This allows the lift to function properly while stopping at two floor levels using the encoder counter system to simulate a third floor.

    Original Title

    ARL-500 2-floor Lifts With Encoder Car Positioning.en.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for operating a 2-floor lift using an ARL-500 encoder counter system. It involves mounting an additional door zone magnet between the two floors, setting the ARL-500 menu to detect 3 floors instead of 2, and adjusting the floor settings of related components to also detect 3 floors instead of 2. This allows the lift to function properly while stopping at two floor levels using the encoder counter system to simulate a third floor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    134 views1 page

    ARL-500 2-Floor Lifts With Encoder Car Positioning - en PDF

    Uploaded by

    Henri Kleine
    This document provides instructions for operating a 2-floor lift using an ARL-500 encoder counter system. It involves mounting an additional door zone magnet between the two floors, setting the ARL-500 menu to detect 3 floors instead of 2, and adjusting the floor settings of related components to also detect 3 floors instead of 2. This allows the lift to function properly while stopping at two floor levels using the encoder counter system to simulate a third floor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Operating 2-floor lifts with ARL-500 with encoder counter system

    Step 1: Mount an additional door zone magnet between two floors (approximately in the middle)

    Door zone magnet


    for 2nd floor

    Additional door zone


    magnet between two
    floors (in the middle)

    Door zone magnet


    ML2 for 1st floor
    ML1

    CAR

    Step 2: Make the following settings in ARL-500 menu:

     System settings --> Position sensing: Encoder


     System settings --> Number of floors: 3
     Door settings --> Door type settings --> Individual settings for floors
    A
    Floor-1: Auto
    Floor-2: None
    Floor-3: Auto
     Display settings --> Floor texts --> Floor 3: Write the same floor text written for Floor 2
     Encoder Settings --> Travel distances --> Slowing distance in high speed: The distance of 817 and 818
    signals. The parameter “1.8-SLOWING DST.” in ADrive should be set 15cm lower than this value
     Encoder Settings --> Travel distances --> Stopping distance in low speed: To the same value with the
    parameter “1.9-STOPING DST.” in ADrive
     Encoder Settings --> Hardware configuration --> Flag length: The length of the door zone magnet
     Exit menu and select “Yes” to save parameters
     Encoder settings --> Learn shaft
     Elevator makes a learning run. After it finishes, exit menu and select “Yes” to save parameters
     If the elevator control cabinet includes an automatic rescue (evacuation) function, then dismount the
    additional door zone magnet between two floors after learning run is finished.

    Step 3: Adjust the number of floor setting of the LOP placed on the 2nd floor as 3 instead of 2 (by menu or
    dipswitches).

    Step 4: Connect the car push button connector of the 2nd floor to the socket labeled as 3 instead of 2 on the
    KABKON in the COP.

    You might also like