Manufacturers & Suppliers: Izod and Charpy Apparatus Make "Dinesh" Model DS 102

Manufacturers & Suppliers
Applied MechanicsDynamicsKinematicsTheory of MachineFluid MechanicsFluid MachinesHydraulics

Heat & Mass TransferAutomobileI.C.EnginesMetallurgyMaterial ScienceMetallography
Refrigeration & Air ConditioningHeat EnginesThermodynamicsSteam & Power Generation
Strength of Materials@Material TestingStructural AnalysisEngineering Mechanics
Chemical Reaction Engineering Apparatus & Instruments
DS
Izod and Charpy Apparatus Make "Dinesh" Model DS 102
Izod Test:16 kgm Charpy Test:30 Kgm
FEATURES
CHARPY, IZOD and IMPACT TENSION(optional) tests can be best
conducted on pendulum impact testing machine Model EIT-160. The
test methods strictly confirm to Indian and British standards namely
IS:3766-1977, IS:1598-1960, BS:131 Part I, Part II & Part III. The
Impact Testing Equipment works on pendulum principle. The difference
between the height of drop of the pendulum before rupture and the
height of the rise after rupture of the specimen is directly proportionate
to the impact energy absorbed by the specimen is directly indicated by the moving pointer.
TECHNICAL DATA
Impact Testing Equipment Charpy Test Izod Test
Pendulum drop angle 140o 85o
Pendulum effective weight 20.59 Kgs. 21.245 Kgs.
Pendulum speed 5.3465 m/sec 3.844 m/sec
Pendulum impact energy 30 Kg.m 16 Kg.m
Min. Graduation (Dial/Digital) 0.2 Kg.m 0.2 Kg.m
Distance of axis of hammer rotation and centre of test piece point
825 mm 825 mm
of test piece hit by hammer.
Max. Permissible loss by friction & windage, etc. 0.25 % of maximum impact energy
Charpy Test Izod Test Impact Tension Test

A) Striking edge A) Striking fork
A) Impact Tension Test
Angle : 75 o Distance between forks : 36 mm.
Angle: 30 o+/- 1o
Radius of curvature : 0.75 mm Radius of curvature : 1 mm
Radius of curvature : 2.05 mm
Horizontal relief : 10o
Width : 18 mm
Vertical relief : 5o
B) Support : B) Support :
B) Support : For gripping specimen with For clamping specimen with
Distance between arms : 40 mm dimension of 10 x 10 mm dimensions of following
Sloping angle : 0o Diameter : 6.4 mm
Relief angle : 10o Length (total) : 68 mm
Radius of curvature : 1.25 mm Length (measuring) : 25.4 mm
Thread of supporting : m10 x 1.5
2549 Bengali Mohalla, Kali Bari Road, Ambala Cantt, Haryana-133001

Tel/Fax: +91-171-4002910 Mob: 0 870 863 4395, 098 967 44 968
Website: www.dineshscientific.com Email: [email protected]
DS
Fatigue Testing Machine : 400 Kgcm
Make "Dinesh" Model DS 132
Fatigue testing machines conduct tests by measuring the force

put onto the sample over many, many cycles until the sample
fails.
Fatigue tests help to determine a test sample's life expectancy
under actual service loads in real-world applications.
The elongation, impact, tearing and indentation tests performed
by fatigue testing machines are used to determine peak load,
elongation percentage, modulus of elongation, and yield to break,
all of which are crucial factors for describing a material's
durability.
Specifications:-
1. Light weight, compact size, simple design
2. Simple lever system for changing load
3. 10 Digit electronic counter instead of mechanical counter

Tel/Fax: +91-171-4002910 Mob: 0 870 863 4395, 098 967 44 968
DS
Torsion Testing Machine : 50Kgm
Make "Dinesh" Model DS 121
INTRODUCTION:
A system of loading which causes section of a bar
or shaft to rotate about its central longitudinal axis
relatively to another such section and which thus
produces twist or torsion in the bar, constitutes a
torsional load. The load may be composed of forces
acting in any direction but the twisting or torsional affect is provided by the couples formed
by these forces in planes normal to the central axis. The torsional shearing stresses in
circular cross section vary from zero at the axis of the section to a maximum value at the
extreme fibres. If no bending is present pure shear exists. Torsion Testing machine
Consists of two independent chucks. The twist is communicated through the test piece to
the other jaw on which a weighted pendulum is attached. The resistance to deflection of
pendulum causes a torque to be applied to the test piece and the angles of deflection of
pendulum is the measure of torque. The machine is built for maximum twisting moment
at about 50 kgm. It is equipped with jaws for accomo- dating test pieces of 10 mm, 15 mm
and 20 mm size either square or circular with square shoulder.
SPECIFICATION:
 Capacity : 0 to 50 kgm.
 Range : ONE
 Rod to be tested : 8 to 20 mm.
 Load of Measurement : Torque and Twist will be read directly.
 Other provisions : Automatic stop in case of failure of specimen.

Tel/Fax: +91-171-4002910 Mob: 0 870 863 4395, 098 967 44 968

Manufacturers & Suppliers: Izod and Charpy Apparatus Make "Dinesh" Model DS 102

Uploaded by

Copyright:

Available Formats

Manufacturers & Suppliers: Izod and Charpy Apparatus Make "Dinesh" Model DS 102

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manufacturers & Suppliers: Izod and Charpy Apparatus Make "Dinesh" Model DS 102

Uploaded by

Copyright:

Available Formats

Manufacturers & Suppliers

Applied MechanicsDynamicsKinematicsTheory of MachineFluid MechanicsFluid MachinesHydraulics

Charpy Test Izod Test Impact Tension Test

2549 Bengali Mohalla, Kali Bari Road, Ambala Cantt, Haryana-133001

Fatigue testing machines conduct tests by measuring the force

2549 Bengali Mohalla, Kali Bari Road, Ambala Cantt, Haryana-133001

2549 Bengali Mohalla, Kali Bari Road, Ambala Cantt, Haryana-133001

You might also like