670B AND 672B MOTOR GRADERS

Introduction And Customer Information

TP15158 A.1

John Deere 670B And 672B Motor Grader

(Manufactured 1986-1997)
(Specifications And Design Subject To Change Without Notice.)

To the Customer
The part numbers in this parts catalog were correct at the time your catalog was published. It is our policy to constantly improve our machines,
and therefore, part numbers may change. When ordering parts, verify part numbers through your dealer.

SI Units of Measure
Metric dimensions are given, where applicable, throughout this parts catalog.

Bolt and Cap Screw Strength Identification

Bolts and cap screws required to have high-strength qualities equivalent to SAE grade 8 are identified throughout this catalog by the description
HS SAE 8 (10.9 for metric). All standard bolts and cap screws are SAE grade 5 (metric 8.8) or lower.

Serial Number Listing Information

Serial number information is listed to show on which machines each part can be used; for example:
– The part can be used on all products.
000000 – The part can be used on products beginning with the serial number listed.
– 000000 The part can be used on products up to and including the serial number listed.
000000 – 000000 The part can be used on products between and including the serial number listed.
When XXXXXX's are listed in place of a serial number, a serial number change was made, but the exact serial number was not available when
the catalog was produced.
If product identification numbers or serial numbers are required for warranty claims or correspondence pertaining to this product, it is extremely
important that all characters be furnished. This point cannot be overemphasized.

Direction Arrow
Arrows are used with illustrations to indicate the front of the unit. “Right-Hand” and “Left-Hand” sides are determined by facing in direction of ma-
chine forward travel.

Box-enclosed Illustrations
A key number, shown in the parts list, is assigned to a box enclosing all parts sold as a service assembly. A box not keyed includes non-current
parts.

Complete Goods Listings

Complete Goods are listed in bold face type. Order separately. Do not include on replacement part order.

Orientation of Engine
“Right Hand” and “Left Hand” sides are determined by standing at the flywheel and facing the engine.

PC2063 (D.1) JUL-18 1/7

 670B AND 672B MOTOR GRADERS

John Deere Reman Components

The service parts listed in this catalog are intended for the repair of original equipment components. Although most service parts may be used
to repair remanufactured components, the remanufacturing process may change parts sufficiently so that service parts are inadequate or not us-
able.

Serial Number Plate Location

Each 670B And 672B Motor Grader May Have Five Serial Number Plates: One For The Basic Grader Or One For The Product Identification
Number, One For The Engine, One For The Transmission, One For The Hydraulic Pump And One For The Front Wheel Drive.
The Basic Grader Serial Number Plate Is Located Below The Operator’s Platform On The Righthand Side Of The Main Frame. This Is The Serial
Number Used In This Catalog Unless Otherwise Noted In The Serial Number Column.
The Product Identification Number Plate Is Located Below The Operator’S Platform On The Right-Hand Side Of The Main Frame. This Is The
Serial Number Used In This Catalog Unless Otherwise Noted In The Serial Number Column.
The Engine Serial Number Plate Is Located On The Right-Hand Side Of The Engine Behind The Engine Oil Filters.
The Transmission Serial Number Plate Is Located On The Right-Hand Side Of The Transmission Front Cover.
The Hydraulic Pump Serial Number Plate Is Located On The Upper Right-Hand Corner Of The Hydraulic Pump.
Left Side And Right Side, Front And Rear Of The Motor Grader Are Viewed By Facing In The Direction Of Motor Grader Forward Travel.
Whenever Serial Numbers Are Required On All Warranty Claims Or Correspondence Pertaining To This Product, It Is Extremely Important That
All Characters Be Furnished. This Point Cannot Be Overemphasized.

Product Identification Number

A.1

First Line Designates

DW - John Deere Davenport Works Grader Manufacturer
670B / 672B Grader Model
X Grader Configuration
123456 Grader Serial Number
Second Line Designates
Motor Grader Unit Type

PC2063 (D.1) JUL-18 2/7

 670B AND 672B MOTOR GRADERS

Engine Serial Number Plate — 4045 & 6068

RGP13837 B.1

Engine Serial Number is Defined by 13 Characters

First Line Designates
1 — Two letters for engine factory designation PE: Torreon, Mexico, CD: Saran, France, JX: Rosario, Argenti-
na
2 — One digit for number of cylinders. 4 Cylinder, 6 Cylinder
3 — Three digits for displacement in liters 045: 4.5 Liter, 068: 6.8 Liter
4 — One letter for aspiration type A= Turbocharged with air-to-water after-cooler
D= Naturally Aspirated
T= Turbocharged
H= Turbocharged with air-to-air after cooler
S= Turbocharged with air-to-sea water after-cooler
5 — Six digits 123456= Engine build sequence number. Sequence numbers
start at 000001
Engine Type is Defined by 9 Alpha-Numerical Characters
6 — Four digits Same as items 2 and 3 above
7 — One letter for aspiration type Same as items 4 above
8 — One or two letters for OEM application F: OEM, FM: Marine, FH: HazLoc, FN: Compressed Natural
Gas
8 — One or two letters for John Deere Vehicle application DW, KV: Construction, RW, LV, L, BM: Tractor, TJ: Forestry, H,
Z, CQ: Combine, N: Picker/Sprayer, E: Windrower
9 — Two or three digits for version 485
10 — Two Letter and 5 or 6 digit for engine Part number DD12345 (Saran Only Engines)

PC2063 (D.1) JUL-18 3/7

 670B AND 672B MOTOR GRADERS

Hydraulic Pump Serial Number

TP8896 A.1

First Line Designates

1. Producing Unit Component Works
2. Pump Type Variable Displacement
3. Pump Model Number LA1
4. Pump Serial Number 000000
Second Line Designates
5. Pump Design The Radial Pump
6. Pump Classification 1
7. Metric Displacement Per Revolution 065 CM3
8. Port Arrangement On The Primary Housing E
9. Port Arrangement On The Secondary Housing F
10. Pump Rotation E
11. Control Valve Option 02
12. Blank.

PC2063 (D.1) JUL-18 4/7

 670B AND 672B MOTOR GRADERS

GEAR REDUCTION MOTOR SERIAL NUMBER

TP10146 A.1

1. The Producing Unit. Component Works

2. The Motor Type. Fixed Motor
3. The Pump Motor Configuration. R.H. Grader
4. Indicates Major Revision. Revision
5. The Motor Serial Number. 001001

TRANSMISSION SERIAL NUMBER PLATE

TP10759 A.1

1. Producing Unit RO - John Deere Component Works

2. Type T-Transmission
3. Transmission Type PF - Power Shift
4. Input Torque 01-99-10-990 Nm(7-730 Lb-Ft)
5. Transmission Serial Number 001001

PC2063 (D.1) JUL-18 5/7

 670B AND 672B MOTOR GRADERS

Trademarks
Throughout this parts catalog, you may find the following Deere and Company trademarks:
Best Bid™ CounterParts™ DEERE™ (Deere™)
Dura-Trax™ Fanggs™ Guardian™
HTH™ Jagz™ JDLink™
MARKS™ MIC™ [Machine Information Center] MTH™
Power Curve™ Powerllel™ PowerShift Plus™
Powerwize™ POWR SAVR™ PowrShift™
ProPath™ Quad-Cool™ Quik-Tatch™
SC-2™ Side-Tracker™ Stinger™
StructureALL™ Swamper™ TMC™ [Total Machine Control]
ValueSelect™ Waratah™ Worksite Pro™
FlexBox™ Funk™ iTorque™
Phoenix™ Phoenix International™ PowerTech™
PowerTech™ E PowerTech™ M PowerTech™ Plus
Precision Joint™ SHIFT-O-MATIC™ SWEDA™ (Super Wide Extreme Dual Axle)
TeamMate™ TeamMate™II TeamMate™ IV
TMII™ TMIII™

PC2063 (D.1) JUL-18 6/7

 670B AND 672B MOTOR GRADERS

Remarks and Abbreviations

The following remarks and abbreviations may appear throughout this parts catalog. Refer to the following table for translations.
Phrase Meaning Phrase Meaning
ALSO ORDER, ORD W/ Also Order NA, NOT USED THIS APPL Not used in this application
AMP Ampere NLA No longer available
APPL, APPL ONLY This application only NSEP Not available separately
AR As required OD Outside diameter
ASSY Complete assembly OPTIONAL Optional
BOAC Bolt-on cutting edge OR Or
CCW Counterclockwise ORD, ORDER Order
COMPLETE Complete OS Oversize
COMPLETE GOODS Complete goods OUTER Outer
CONVENIENCE ASSY, CA Convenience assembly PKG, PACKG Package, Packet of
CTL, CUT TO LENGTH Cut to length PTO Power Take Off
CW Clockwise RATIO Ratio
FOR For REAR Rear
FRONT Front REMAN Remanufactured
GAS Gasoline REPL Replaces
HP Horsepower RH Right-hand
HS, HEAD MARKED High Strength, head marked SN Serial number
ID Inside diameter STD Standard
INCH Inch SUB Replaced by
INCL KEYS Includes keys… SUB COMPONENTS Substitute components (of the
kit or assy)
INCL, INCLUDES Includes… SUB FOR Substitutes for
INCLUDES PARTS/ ITEMS Includes parts/items marked… TEETH, Z Number of gear teeth
MARKED
INNER Inner TK Thickness
KIT Kit UP, UPPER Upper
L Number of links US Undersize
LF, LINE FILL Line Fill USE UNTIL EXHAUSTED Use until exhausted
LGP Low Ground Pressure USE WITH Use with
LGTH Length VEC Vehicle Electronic Controller
LH Left-hand VLC Vehicle Load Center
LOW, LOWER Lower W/ With
MAKE FROM, MF Make from W/O Without
MARKED Marked WHOLE GOODS Whole Goods
MATCHED SET Matched set

PC2063 (D.1) JUL-18 7/7