Scribd
Upload
418 views4 pages

Cisco CUCM - SIP Integration With Zoom

The document provides instructions for configuring a SIP phone in Cisco Unified Communications Manager (CUCM). It involves: 1. Creating a new phone security profile with digest authentication enabled. 2. Building a new user with a digest credential password for the SIP device to use for authentication. 3. Adding the SIP device in CUCM with the owner user ID, security profile, and digest user set from previous steps. 4. Configuring lines on the SIP device matching standard user settings. 5. Associating the SIP device with the user in CUCM to complete the configuration.

Uploaded by

abeastinme
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
418 views4 pages

Cisco CUCM - SIP Integration With Zoom

The document provides instructions for configuring a SIP phone in Cisco Unified Communications Manager (CUCM). It involves: 1. Creating a new phone security profile with digest authentication enabled. 2. Building a new user with a digest credential password for the SIP device to use for authentication. 3. Adding the SIP device in CUCM with the owner user ID, security profile, and digest user set from previous steps. 4. Configuring lines on the SIP device matching standard user settings. 5. Associating the SIP device with the user in CUCM to complete the configuration.

Uploaded by

abeastinme
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

First, let’s configure a new Phone Security Profile for the SIP phone.

01) Go to SYSTEM | SECURITY PROFILE | PHONE SECURITY PROFILE

02) Simply hit FIND and scroll down to the bottom of the list (you may need to click to a second page) and
locate “Third-party SIP Device Basic – Standard SIP Non-Secure Profile” and click on it

03) Once you see it’s properties, simply hit COPY to create a new copy of it. Give the new phone security
profile a name, I’m using “Third-party SIP Device Basic – Digest”

04) Check the checkbox next to ENABLE DIGEST AUTHENTICATION and hit SAVE

Now let’s build a user to authenticate the SIP device

1) GO to USER MANAGEMENT | END USER and click ADD NEW

2) Enter in your USER ID, PASSWORD, PIN, and LAST NAME

3) You must also enter in a password in the DIGEST CREDENTIALS and CONFIRM DIGEST CREDENTIALS
field – this is the password that the SIP client will use to authenticate

***UPDATE NOTE: If you are Active Directory Integrated, you still set the DIGEST CREDENTIALS in CUCM
and use these credentials on the sip client.***

04) Click SAVE


***remember the UserID and Password and DN of the device.

Next let’s build the SIP phone in CUCM

1) Go to DEVICE | PHONE and click ADD NEW

2) Select THIRD-PARTY SIP DEVICE (BASIC) and click NEXT

3) Enter in a 12 digit MAC address (this have to be a valid MAC address)

4) Enter the pertinent information for the SIP DEVICE settings – it should mostly be configured the same as a
standard phone on your system except for the following settings

a) in the OWNER USER ID field select the user you created above

b) in the DEVICE SECURITY PROFILE field select the security profile you created above

c) in the DIGEST USER field select the user you created above

05) click SAVE


06) Configure the line settings for the SIP device – the line settings should match the line settings of your
standard user’s Cisco IP phones (For this we’ll use 7154545 as DN) – there are no special attributes that we
need to worry about on the line configuration.

Now let’s go back to the user configuration and associate this device

01) Go to USER MANAGEMENT | END USER and search for the SIP user you created above, once you find it,
click on it

02) scroll down to DEVICE ASSOCIATIONS and click on the DEVICE ASSOCIATION button

03) locate and select the SIP device you created above

04) Check the checkbox next to this device and click SAVE SELECTED/CHANGES

05) Click GO next to the BACK TO USER related link near the upper right-hand corner

06) Click SAVE one more time on the END USER CONFIGURATION screen

You have completed the steps to configure the SIP device in CUCM.
Go to Zoom web portal and fill in the information that you have obtained from the PBX.

Transport protocol: UDP

User Name*: 7154545 (This should be


the DN)

Password: password (whatever the


digest password you set on the user
information)

Authorization Name*: Zoom

Registrar Server*: This will be the


subscriber of the DP (Primary server
the device registers to)

You might also like