JOB NO. ITEM NO.

P-510/520

PURCHASE ORDER NO.

SPECIFICATION NO.
CONTROLLED VOLUME PUMP (API 675-3RD ) REVISION NO. 0 DATE 5/16/2017
DATA SHEET PAGE 1 OF 2 BY
METRIC (kg/cm2)
1 APPLICABLE TO: PROPOSAL PURCHASE AS BUILT
2 FOR REVIVAL / REVAMPING OF R12A PLATFORM PROJECT UNIT CORROSION INHIBITOR INJECTION PUMPS
3 SITE R12A PLATFORM NO. OF PUMPS REQUIRED 2
4 SERVICE CONTINUOUS MODEL PP680-S-E SIZE AND TYPE DOUBLE DIAPHRAGM
5 MANUFACTURER PULSAFEEDER INC SERIAL NO.

6 NOTE: INDICATES INFORMATION TO BE COMPLETED BY PURCHASER BY MANUFACTURER

7 GENERAL
8 NO. MOTORS DRIVEN 2 OTHER DRIVER TYPE
9 PUMP ITEM NO'S P-510/520 PUMP ITEM NO'S
10 MOTOR ITEM NO'S PM-510/520 DRIVER ITEM NO'S GEAR ITEM NO'S
11 MOTOR PROVIDED BY DRIVER PROVIDED BY GEAR PROVIDED BY
12 MOTOR MOUNTED BY DRIVER MOUNTED BY GEAR MOUNTED BY
13 MOTOR DATA SHEET NO. DRIVER DATA SHEET NO. GEAR DATA SHEET NO.

14 OPERATING CONDITIONS LIQUID

15 CAPACITY @ PT: (L/h) TYPE OR NAME OF LIQUID Corrosion Inhibitor
16 NORMAL MINIMUM RATED 4.8 PUMPING TEMPERATURE: (°C)
17 DISCHARGE PRESSURE: (kg/cm²G) NORMAL MAX 40 MIN 16
18 MAXIMUM 12.29 RATED SPECIFIC GRAVITY 0.95 MAXIMUM 0.93 MINIMUM
19 SUCTION PRESSURE: (kg/cm²G) SPECIFIC HEAT Cp (kJ/kg °C)
20 MAXIMUM 0.04 MINIMUM VISCOSITY 140 MINIMUM MAXIMUM
21 DIFFERENTIAL PRESSURE: (kg/cm²) CORROSIVE/EROSIVE AGENTS
22 MAXIMUM 12.25 CHLORIDE CONCENTRATION (PPM)
23 NPIP AVAILABLE: (kg/cm²G) 0.85 H2S CONCENTRATION (PPM)
24 (INCLUDING ACCELERATION LOSSES) LIQUID TOXIC FLAMMABLE OTHER Corrosive
25 TURNDOWN RATIO 10:01

26 PERFORMANCE SITE AND UTILITY DATA

27 NUMBER OF FEEDS 1 RATED CAPACITY (L/h) 5.51 LOCATION INDOOR OUTDOOR
28 NPIP REQUIRED (INCLUDING ACCEL LOSSES) (kg/cm²G) 0.35 HEATED UNHEATED UNDER ROOF
29 BHP RATED 0.006 AT RELIEF SETTING 0.0071 ELECTRICAL AREA CLASS Class 1 Div2 Grp D T3
30 PLUNGER SPEED (strokes/min) 73 DESIGN MAX 73 WINTERIZATION REQD TROPICALIZATION REQD
31 DIAMETER (mm) 13 LENGTH OF STROKE (mm) 13 SITE DATA
o
32 PUMP HEAD: 1 RANGE OF AMBIENT TEMPS:MIN/MAX 16 / 40 C
33 MAXIMUM PRESSURE (kg/cm²G) 14 UNUSUAL CONDITIONS
34 HYDRO TEST PRESSURE (kg/cm²G)21 DUST FUMES SALT ATMOSPHERE
35 MAX DISCH PRESS. W/ JOB DRIVER (kg/cm²G) 18 OTHER CORROSIVE, SALT LADEN, MARINE ENVIRONMENT
36 MAX BHP BASIS GEAR STRENGTH 0.5 UTILITY CONDITIONS

37 CONSTRUCTION ELECTRICITY DRIVERS HEATING CONTROL SHUTDOWN

38 SIZE ANSI FACING POSITION VOLTAGE 415 230
39 CONNECTIONS RATING HERTZ 50 50
40 SUCTION 0.5" 150 RF BOTTOM PHASE 3 1
41 DISCHARGE 0.5" 300 RF TOP COOLING WATER INLET RETURN DESIGN MAX D
42 FLUSH TEMP °F MAX
43 PRESS. (PSIG) MIN
44 LIQUID END JACKET REQ'D SOURCE
45 TYPE DIAPHRAGM PLUNGER INSTRUMENT AIR MAX MIN
46 DIAPHRAGM DIA (mm) 57.15 NO REQ. 2 PRESSURE (PSIG)

47 VALVES/FEED SUCTION DISCHARGE APPLICABLE SPECIFICATIONS:

48 TYPE BALL BALL API 675 POSITIVE DISPLACEMENT PUMPS - CONTROLLED VOLUME
49 NUMBER 2 2 GOVERNING SPECIFICATION (IF DIFFERENT)
50 NACE MR-0103 (6.14.2.13) NACE MR-0175 (6.14.2.13)
51 OTHER

52 1
53 2
 JOB NO. ITEM NO. P-510/520
CONTROLLED VOLUME PUMP (API 675-3RD ) REVISION NO. 0 DATE 5/16/2017
DATA SHEET PAGE 2 OF 2 BY
METRIC (kg/cm2)
1 MATERIALS CONTROLS
2 LIQUID END SS316/SS316L TYPE: SIGNAL:
3 CONTOUR PLATE NA MANUAL REMOTE PNEUMATIC
4 HYDRAULIC DIAPHRAGM PTFE AUTOMATIC LOCAL ELECTRONIC
5 PROCESS DIAPHRAGM PTFE STROKE CONTROL:
6 PLUNGER CAST STEEL PNEUMATIC: (kg/cm²G)
7 LANTERN RING NA MINIMUM MAXIMUM
8 PACKING GLAND NA ELECTRONIC (mA):
9 PACKING NA MINIMUM MAXIMUM

10 VALVE SS316 OTHER PURCHASE REQUIREMENTS

11 VALVE SEAT SS316/SS316L NAMEPLATE UNITS U.S. CUSTOMARY SI
12 VALVE GUIDE SS316/SS316L VENDOR FURNISHED PROCESS PIPING
13 VALVE BODY SS316/SS316L
14 VALVE GASKET PTFE VENDOR REVIEW PIPING DRAWINGS
15 FRAME CAST IRON VENDOR FURNISHED PULSATION SUPRESSION DEVICES
16 SPECIAL MATERIAL TESTS (6.14.2.5) VENDOR FURNISHED RELIEF VALVE
17 INTERNAL EXTERNAL
18 LOW AMBIENT TEMPERATURE MATERIALS TESTS (6.14.6) RELIEF VALVE SETTING (kg/cm²G) 14.29
19 VENDOR FURNISHED BACK-PRESSURE VALVE

20 QA INSPECTION AND TEST DOUBLE CHECK VALVES REQUIRED

21 COMPLIANCE WITH INSPECTORS CHECK LIST OIL-FILLED PRESSURE GAUGES REQUIRED
22 CERTIFICATION OF MATERIALS (user to define components in remarks) VENDOR FURNISHED CONTROL PANEL
23 FINAL ASSEMBLY CLEARANCES (user to define components in remarks) BASEPLATE PREPARED FOR EPOXY GROUT
24 SURFACE AND SUBSURFACE EXAMINATIONS PROVIDE TECHNICAL DATA MANUAL
25 RADIOGRAPHY PUMP DESIGN PRESSURE (kg/cm2g) 31
26 ULTRASONIC PUMP DESIGN TEMPERATURE (oC) 60

27 MAGNETIC PARTICLE PREPARATION FOR SHIPMENT

28 LIQUID PENETRANT DOMESTIC EXPORT EXPORT BOXING
29 CLEANLINESS PRIOR TO FINAL ASSEMBLY OUTDOOR STORAGE MORE THAN 6 MONTHS
30 HARDNESS OF PARTS, WELDS & HEAT AFFECTED ZONES WEIGHTS (LBS)
31 FURNISH PROCEDURES FOR OPTIONAL TESTS PUMP BASE GEAR DRIVER

32 TESTS REQ'D WIT OBS DRIVERS

33 HYDROSTATIC (8.3.2) X MOTOR:
34 STEADY STATE ACCURACY X MANUFACTURER
35 REPEATABILITY TYPE
36 LINEARITY FRAME NO. IEC 80-B14
37 PERFORMANCE (8.3.4) CONSTANT SPEED
38 MECHANICAL RUN (8.3.5)
39 NPIP(8.3.7.1)
40 COMPLETE UNIT (8.3.7.2)
41 SOUND LEVEL (8.3.7.3)
42 HIGH DISCHARGE PRES (8.3.7.4)
43 FACTORY ACCEPTANCE (8.3.8) VARIABLE SPEED

44 LUBRICATION FLUID HP 0.5 RPM 1450

45 CRANKCASE INTERMEDIATE VOLTS 415 PHASE 3
46 HYDRAULIC FLUID HERTZ 50 SERVICE FACTOR ###
47 ACCESSORIES ENCLOSURE
48 SPEED REDUCER MANUFACTURER Pulsafeeder Inc OTHER (SEE SEPARATE DATA SHEETS)
49 INTEGRAL SEPARATE GAS DRIVEN
50 MODEL Dynalloy STEAM TURBINE
51 RATIO 1:20 OTHER
BASEPLATE UNDER Both Pumps, Accessories & Process Piping within skid
52 boundry
53 COUPLING MANUFACTURER LoveJoy
54 TYPE Spider

55 REMARKS
56

06/95 SHT 2 OF 2 API675.XLS REV 0