Used to transfer files to or upload reports from the 4007ES using the Ethernet port on your laptop. J1 Ethernet Port P2 Serial Interface port is used for connection to remote services. This operation requires you to enable the Ethernet port by installing Service Mode Jumper J3.. Card Power and Communications connectors. J2 USB Port Used to transfer files to or upload reports from the 4007ES. P3 & P4 Caution: Locking tabs are located up, on the top of the connectors.
LED Purpose 1 Ethernet connection LED (ON when connected, blinks with activity) J3 Service Mode This jumper is normally positioned on only one of J3’s two pins. When installed, shorting the two pins, the Ethernet 2 Flashes once a second to show the CPU is processing Jumper Port connection is enabled and a “SERVICE MODE JUMPER INSTALLED” trouble is generated. 3 Flashes once per polling cycle 4&5 Not used 6 Reset
SW1 Reset Switch – Cold Start. Clears Disables, Manual Overrides, and Logs U11 - Contains the panel Serial Number and MAC address
All specifications and other information shown were current as of document revision date and are subject to change without notice. TYCO, SIMPLEX, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited. Rev. A 4007ES CPU and Display Board 4007ES NAC PSU (Hybrid) Terminal Blocks on the 4007ES NAC PSU BOARD TB Terminal(s) Purpose 1-4 IDNet 1 5&6 Aux/SNAC 7-10 RUI 2 1-8 NAC 1 & 2 (Class A operation is software selectable. Class B operation has six software selectable EOLs). 3 1-8 NAC 3 & 4 (Class A operation is software selectable. Class B operation has six software selectable EOLs). 4 1&2 Battery connection terminals
LEDS on the 4007ES NAC PSU BOARD
LED Color Behavior LED 1 Aux/SNAC Y Aux Power is Default, 24 volt non-resettable output SNAC operation depends on the selected Point Type LED 2 RUI Trouble Y ON for Class A RUI trouble, otherwise OFF LED 3 Comm Y ON when offline with Master, otherwise OFF LED 4 General Power Y ON for AC Power Loss, Earth Fault, Overcurrent Trouble LED 5 NAC 1 Y ON for OverCurrent, Short, Open LED 6 RUI OC Y Fast blink on short (OverCurrent) LED 7 NAC 2 Y ON for OverCurrent, Short, Open LED 8 NAC 3 Y ON for OverCurrent, Short, Open LED 9 NAC 4 Y ON for OverCurrent, Short, Open LED 10 AC Status G OFF on AC Fail, otherwise ON LED 11 IDNet Loop III Y A and/or B terminal short, or Class A open trouble LED 12 IDNet Loop II Y A and/or B terminal short, or Class A open trouble LED 13 IDNet Loop I Y A and/or B terminal short, or Class A open trouble LED 14 IDNet Earth - Y Negative Earth Fault LED 15 IDNet Earth + Y Positive Earth Fault LED 16 IDNet Y IDNet Channel Fail LED 17 IDNet Comm Y ON when offline with MAster, otherwise OFF
P Connectors on the 4007ES NAC PSU BOARD
P Purpose 1 RUI Class Selector. Default is Class A. For Class B operation, move the two jumpers to short the top two pins. 2 IDNet+ Loop A Class. Default is Class A. For Class B operation, move the two jumpers to short the top two pins. 10 AC power input connector 11 Connector for ribbon harness to optional city card or optional relay card
J Connectors on the 4007ES NAC PSU BOARD
Associated J Purpose with P 5 Communications and Power for Zone/Relay card(s) 7 Connector for IDNet Loop B card (first expansion IDNet card) 8 Connector for IDNet Loop C card (second expansion IDNet card) 9 4 Default - NAC Power Supply Online Jumper removed NAC Power Supply Offline 11 6 Battery Depleted Jumper - * Canadian operation is not the default jumper setting 12 8 Default 1-2 IDNet Online Jumper removed IDNET Offline 13 9 25V Regulator Jumpers 1-2, 3-4 default. Remove Jumpers and plug in 25V Regulator Harness when using the 25V Regulator Module 14 9 25V Regulator Jumpers 1-2, 3-4 default. Remove Jumpers when using the 25V Regulator Module 15 Communications and Power for Zone/Relay card(s) 16 Communications and Power for the retainer mounted CPU card 17 Communications and Power for an option card
