C32 Project Guide 1 PDF

©2009 Caterpillar® All rights reserved.
General ................................................................................ 1
C32 Engine Information.............................................................................. 1
Product Identification Information ................................................................ 1
Marine Propulsion High Performance Price List C32 MP3MC ...................... 1
Marine (Auxiliary) Gen Set Engine Price List C32 MGE3MC ........................ 1
Air System ........................................................................... 7

Engine Protection Strategy ......................................................................... 7
Air Cleaner ............................................................................................... 7
Crankcase Fumes Disposal ......................................................................... 7
Crankcase Piping System ........................................................................... 8
Cooling System .................................................................... 9

Introduction .............................................................................................. 9
Coolant Flow Control ................................................................................. 9
Coolant Temperature Control ...................................................................... 9
Treated Water Pumps ................................................................................ 9
Sea Water Pump ..................................................................................... 10
Engine Mounted Shunt Tanks and Venting ................................................. 10
Heat Exchanger Cooled Engines ................................................................ 11
Keel Cooled Engines ................................................................................ 11
Combined Cooling ................................................................................... 11
Cold Starting (Jacket Water Heaters) ......................................................... 11
System Monitoring .................................................................................. 11
Safety Advisory ...................................................................................... 12
Serviceability .......................................................................................... 12
Service Ports .......................................................................................... 12
Water Quality, Rust Inhibitors, and Antifreeze ............................................. 12
Cooling Connections ................................................................................ 13
Heat Recovery (Cabin Heater) ................................................................... 14
Exhaust System .................................................................. 16

Exhaust Backpressure Limits ..................................................................... 16
Turbochargers ......................................................................................... 16
Exhaust Piping ........................................................................................ 16
©2013 Caterpillar All rights reserved.

Fuel System ....................................................................... 18
Tank Position .......................................................................................... 18
Line Restriction ....................................................................................... 18
Flexible Connections ................................................................................ 18
Fuel Cooler ............................................................................................. 18
Fuel Filters .............................................................................................. 18
Lubrication Oil System........................................................ 19

General .................................................................................................. 19
Oil Pan ................................................................................................... 19
Oil Filters ................................................................................................ 19
Pre-Lubrication Recommendations ............................................................. 20
Power Take Offs ................................................................. 20

Rear Hydraulic Pump Drives ...................................................................... 20
Starting System ................................................................. 21

Air Starter Description ............................................................................. 21
Air Quality and Filtration .......................................................................... 21
Lubrication ............................................................................................. 21
Emergency Starting ................................................................................. 21
Emergency Starting Procedure: ............................................................. 22
Mounting System ............................................................... 24

Isolator Mounts ....................................................................................... 24
Non-Thrust Mounts Mount Characteristics ............................................. 24
Thrust Mounts Mount Characteristics .................................................... 24
Engine Preservation and Packaging..................................... 25

Shipbuilder’s Responsibility................................................ 26
Reference Material ............................................................. 27

General
C32 Engine Information
The C32 Tier 3, Separate Circuit Aftercooled (SCAC) engine is certified to 2013
EPA Tier 3 and IMO II Marine commercial emissions standards. All engines have
SAE #0 flywheel housing; Caterpillar does not offer a SAE #1 option for this
product. Details on standard and optional selections are listed by system in each
product price list. The product price list can be accessed through Power Net. The
Reference Materials section at the end this guide provides links to Power Net and
other resources.
Product Identification Information

Marine Propulsion High Performance Price List C32 MP3MC
EPA T3 / IMO II Engine E-Model: EE086
EPA T3 / IMO II Engine S/N Prefix: SDN
IMO II Only Engine E-Model: EE086
IMO II Only Engine S/N Prefix: SDN
Marine (Auxiliary) Gen Set Engine Price List C32 MGE3MC

EPA T3 / IMO II Engine E-Model: EE128
EPA T3 / IMO II Engine S/N Prefix: RSD
IMO II Only Engine E-Model: EE128
IMO II Only Engine S/N Prefix: RSD
GENERAL
1
C32 SCAC MARINE PROJECT GUIDE
Note: The following images may not reflect your engine.
Heat Exchanger Cooled Engine (Rear Mounted Sea Water Pump)
Figure 1: Front View

GENERAL
Figure 2: Left View

2
Figure 3: Rear View (Flywheel End of Engine)
GENERAL
Figure 4: Right View
3
Note: The following images may not reflect your engine.

Keel Cooled Engine

GENERAL
Figure 6: Left View
4
Figure 7: Rear View (Flywheel End of Engine)
GENERAL
Figure 8: Right View
5
Note: The following image may not reflect your engine.
Heat Exchanger Cooled Engine (Front Mounted Sea Water Pump)

GENERAL
6
Air System
Engine Protection Strategy
The engine protection strategy is in place to protect engine components from being
damaged due to thermal wear caused by high inlet air temperatures. The Engine
Protection Strategy is only implemented on EPA Tier 3 Ratings this strategy is not
active on IMO II only ratings. The function of this strategy is based on inlet air
temperature to the turbo compressor and the sea water temperature provided to
the engine (Both have a direct impact on Inlet Manifold Temperature [IMAT]).
The inlet air temperature to the turbo compressor is measured by a new
temperature sensor located in the air cleaner housing.
The Engine Protection Strategy Chart which is also referred to as the ambient
capability chart is published in TMI. This data is stored under Performance Data but
within the Supplementary Data tab.
If you have trouble viewing the Ambient Capability Chart, select the metric units
toggle before retrieving the data.
Air Cleaner
The inlet air cleaners system is standard on each engine configuration; however, it
is considered an optional attachment. There is an option in the price list to remove
the cleaner group if a customer wants to provide an aftermarket air cleaner system.
The Cat filter elements are disposable. The filter elements can be removed from the
bottom of the cleaner housing as illustrated in the installation drawings on EDDC.
Crankcase Fumes Disposal

Normal combustion pressures of an internal combustion engine cause pressure
buildup within the crankcase due to blowby. Vent tubes and crankcase breathers
are provided to allow this gas to escape.
Do not vent crankcase fumes into the engine room or any other indoor/enclosed
spaces.
Crankcase fumes should be discharged directly to the atmosphere through a
venting system individual for each engine.
Loops or low points in a crankcase vent pipe should be avoided or equipped with a
drain at the lowest point and checked daily to prevent liquid locks from the
condensation in the pipe and thus restricting discharge of fumes. Where horizontal
runs are required, install the pipe with a gradual rise of 41.7 mm/m, (1/2 in/ft),
slope from the engine. The weight of the vent pipes will require separate off-engine
supports as part of the installation design. Further additional flexible connections
will need to be installed to accommodate the engine movement.
AIR SYSTEM
7
Crankcase Piping System

Vent the pipe out of the vessel directly into the atmosphere at a well considered
location and be fitted with a gooseneck or similar arrangement to keep rain or
water spray from entering the engine. Consideration should also be given to other
equipment located near the discharge area. If not located properly, the oil carryover
can accumulate over time and become unsightly.
An oil condensate trap will minimize the amount of oil discharged from the vent
pipe.
AIR SYSTEM
8
Cooling System
Introduction
The cooling system configuration for the C32 EPA Tier III Commercial Propulsion
and Auxiliary engines are identified as Separate Circuit Aftercooled (SCAC)
Engines.
The maximum glycol concentration for the jacket water circuit is 50/50 water-to-
glycol concentration. The recommended glycol concentration for the aftercooler
SCAC circuit is 80/20 water-to-glycol concentration.
The cooling system was designed to operate properly with the following
temperatures supplied to the engine:
• 52 deg C (125.6 deg F) maximum water temperature to the aftercooler.
• 81 deg C (178 deg F) maximum temperature to the oil cooler.
Sacrificial anodes are not included on the SCAC product. The SCAC engines were
designed to be used with a zinc bonding system, where the zinc is installed on the
vessel. Instructions for installing the bonding system are illustrated in the C7 - C32
Marine Engine Electronics Application and Installation Guide.
Coolant Flow Control

The external circuit resistance setting establishes the total circuit flow by balancing
total circuit losses with the characteristic pump performance curves. Correct
external resistance is very important. Too high a resistance will result in reduced
flows to the aftercooler and/or jacket water circuit, causing their effectiveness to
decrease. If there is too low a resistance, the fluid velocity may increase and
exceed fluid velocity limits, and cavitation/early wear could be the result.
The Pump Performance Curves in TMI illustrates the maximum recommended
external resistance versus coolant flow at specific engine speeds.
Coolant Temperature Control

The Tier III SCAC engines use inlet control temperature regulators/thermostats to
provide uniform coolant temperature to the jacket water circuit and aftercooler
circuit.
The jacket water circuit has two regulators. The aftercooler circuit SCAC has one
regulator.
Treated Water Pumps

The C32 Tier III Commercial Propulsion and Auxiliary engines have two gear-driven
COOLING SYSTEM
centrifugal water pumps mounted on the front housing. The right-hand pump
(viewed from the flywheel end) is the jacket water pump and supplies coolant to
the oil cooler, block, and heads. The left-hand pump, referred to as the SCAC
pump, supplies coolant to the fuel cooler and aftercooler. Each pump is equipped
with pump covers that have two service ports available for measuring coolant
temperature and pressure at pump inlet, and one service port on the pump housing
for measuring at the pump outlet.
9
Sea Water Pump

A Cat engine driven sea water pump supplies sea water to the aftercoooler heat
exchanger, jacket water heat exchanger, and gear/transmission oil cooler. This is
not a self-priming sea water pump; pump performance data is published in TMI
under Component Data. Some systems may require an auxiliary priming system to
meet the application requirements.
For commercial propulsion product the sea water pump is only mounted on the left
rear of the engine when viewed from the flywheel end. The sea water pump is
supplied as standard equipment on heat exchanger cooled engines.
Auxiliary/genset engines have a sea water pump option.
For auxiliary engines there are three options:
1. Left Rear Mounted Sea Water Pump (viewed from the flywheel end).
2. Front Mounted Sea Water Pump driven off the crankshaft by way of the
hydraulic pump drive adapter.
3. No Factory Sea Water Pump. The customer will supply their own sea water
pump.
The front mounted sea water pump option exists to avoid interference issues with
the rear mounted sea water pump auxiliary equipment (generator, pump, etc.)
packaged by the dealer/customer.
The rear pump has a 0.933:1 pump to engine speed ratio. The front pump has a
1:1 pump to engine ratio.
The no pump option is available for those customers who prefer to provide their
own sea water pump.
Engine Mounted Shunt Tanks and Venting

The engine mounted shunt tanks are standard on all C32 commercial Tier III
products. Each shunt tank for heat exchanger cooled arrangements has a sight
glass installed on the outboard side of the engine. The sight glass is for visual
inspection purposes only and does not indicate that the system is full. Do not
assume the tank is full when the sight glass partially or completely submerged.
Consider the variation when taking into account installation angles and/or operating
conditions.
The coolant system is full when the coolant level is in contact with the bottom of
the fill neck, the most accurate way to verify the system is full is by removing the
fill cap and confirm the coolant level is in contact with the bottom of the fill neck.
(Flashlight maybe needed.)
COOLING SYSTEM
The sight glass on the jacket water expansion tank is located above the low level
sensor, in a zero degree installation condition there is approximately 8 liters (8.5
quarts) of coolant difference between the sight glass and low level sensor. The
Jacket Water coolant sight glass will be partially submerged when the coolant level
is in contact with the bottom of the fill neck, this is normal.
10
The sight glass on the aftercooler SCAC expansion tank is located above the low
level sensor, in a zero degree installation condition there is approximately 3 liters
(3.2 quarts) difference between the sight glass and low level sensor. At a zero
degree installation condition the SCAC coolant sight glass will be completely
submerged when the coolant level is in contact with the bottom of the fill neck,
this is normal.
Jacket water and aftercooler SCAC tank volumes are published in TMI under the
Physical Data Tab for each system. You can find information on other components
within the cooling system in this location as well, such as details on the regulators,
aftercooler, and heat exchangers.
The small lines routed to the top SCAC tank and the top of the jacket water tank
are vent lines.
Heat Exchanger Cooled Engines

Heat exchanger cooled engines were designed to accommodate thermal expansion
of the coolant in the closed engine circuit.
Keel Cooled Engines

In a keel cooled application the shunt tanks cannot accommodate any external
expansion volume. An external vessel mounted expansion tank must connect to the
engine at the top of the shunt tanks in place of the engine mounted fill neck and
cap. (Each engine is shipped with two flanges explained in the Cooling Connections
section.)
Proper venting is required for all applications. The vent lines that shipped with the
engine should be removed. The dealer/ customer must route vent lines from the
engine to the dealer/ customer supplied auxiliary expansion tank at a constant
upward slope. The ports on the engine mounted shunt tanks must be plugged.
Port/plug size and locations are called out on the engine installation drawings,
published on EDDC.
Combined Cooling
Combined cooling can be achieved with the keel cooled engine arrangement.
• Maximum Inlet Coolant Temperature Combined Cooling:
52 deg C (125.6 deg F)
• Maximum Combined Engine Outlet Temperature:
98 deg C (208.4 deg F)
Cold Starting (Jacket Water Heaters)

Jacket water heaters may be required to meet cold starting and load acceptance
COOLING SYSTEM
criteria. Caterpillar offers 120V and 240V jacket water heater options for C32
SCAC product, both options deliver 1500W.
System Monitoring
During the design and preparation phase, it is important that provisions are made to
measure pressure and temperature differentials across major system components.
11
This allows accurate documentation of the cooling system during the

commissioning sea trial. Future system problems or component deterioration (such
as fouling) are easier to identify if baseline data is available.
Safety Advisory
The engine treated water systems are pressurized; hot coolant can cause serious
burns. Before opening any treated water system stop the engine, wait until the
engine is cool and proceed with CAUTION.
Serviceability
Suitable access should be provided for cleaning, removal, or replacement of all
system components. Isolation valves should be installed as deemed necessary to
facilitate such work.
Caterpillar recommends removing the heat exchanger cores and cleaning them in a
hydrosolv solution. If necessary the heat exchanger tubes in both the jacket water
and aftercooler heat exchangers can be inspected and brush-cleaned without
removing the tube bundles from the heat exchanger housings, or draining the
treated water circuits. The sea water circuit must be drained from the jacket water
and aftercooler heat exchangers. Drain plugs are located on the jacket water heat
exchanger and the sea water pump. The treated water circuits DO NOT have to be
drained. (When conducting this inspection with the tube bundles installed and the
treated water circuit filled with coolant, the technician should never attempt to
remove the tube bundle. The respective treated water circuit will leak
uncontrollably into the engine room once the seal is compromised.)
The top and bottom bonnets must be removed from the heat exchanger housing
after the sea water is drained.
Service Ports
Service ports can be found on the Engine Installation Drawings, published in EDDC.
Ports on Jacket Water (JW) Heat Exchanger
• Sea Water Drains
• Treated Water Drain
Port on Aftercooler SCAC Heat Exchanger
• Treated Water Drain
Water Quality, Rust Inhibitors, and Antifreeze

Maintaining water quality is very important in closed cooling systems. Excessive
hardness will cause deposits, fouling, and reduced effectiveness of cooling system
COOLING SYSTEM
components. Caterpillar has coolant inhibitor available to properly condition the

cooling water. When using Cat inhibitor, the cooling water piping must not be a
galvanized material, and aluminum should not be used. If the piping is galvanized,
the zinc will react with the coolant inhibitor causing material to deposits in the
treated water system which may lead to fouling in the treated water circuit.
12
Cooling Connections
Caterpillar supplies flex connections for both the heat exchanger and keel cooled
engine configurations for external water connections. Flange connection options
include standard 3 inch 4 bolt ANSI English flanges and an 80 mm standard 8 bolt
DIN flange connection.
Optional flexible connections with standard European 8 Bolt ANSI DIN flanges are
also available.
The heat exchanger cooled
engines ship with two flex
connections (Figure 12 and Figure
13) for the sea water circuit; one Sea
is located on the sea water pump Water
inlet, and one on the jacket water Supply
heat exchanger outlet.
The keel cooled engines (Figure Sea
13) ship with four flex Water
connections. Each flex connection Return
must be mounted to the keel
cooler adapters prior to installing Figure 10: Heat Exchanger Cooled Connections, Rear
Pump Arrangement (Sea Water)
the vessel supply and return
piping to the engine. The keel
cooler adapters are attached to
the respective jacket water and
Sea
SCAC regulator housings
Water
(deaerators).
Return
Note: Pay close attention to the
Supply and Return for the
respective cooling circuits. Sea
Viewed from the front of the Water
engine the Jacket Water Supply is Supply
the upper left connection. The
SCAC Water Supply is the lower Figure 11: Heat Exchanger Cooled Connections, Front
right connection. Pump Arrangement (Sea Water)
The vessel mounted coolant

expansion tanks must be piped Jacket SCAC
Water Water
directly to the engine mounted
Cold Hot
shunt tanks to maintain positive Return
Supply
head pressure on the pump inlet.
COOLING SYSTEM
Keel cooled engines include two

6-bolt weld flange adapters to be SCAC
Jacket
used for connecting Water Water
dealer/customer supplied auxiliary Hot Cold
expansion tanks to engine Return Supply
mounted tanks.
Figure 12: Keel Cooler Connections (Treated Water)
13
The vessel mounted expansion tanks should NOT be connected in-line with the keel
cooler supply and return connections.
The vessel expansion tanks must be sized to account for the total system
expansion volume (engine, piping, keel coolers, etc).
Engine cooling system volumes are available in TMI under the physical data tab of
the jacket water and/or SCAC tank groups. The tank group number is the item that
should be searched.
Heat Recovery (Cabin Heater)

Caterpillar does not offer a heat recovery system or cabin heater options.
If aftermarket system is required Caterpillar recommends installing shut off valves
on the supply and return lines from the engine to the system. Be sure to include the
coolant volume in the cabin heater loop in the total coolant system volume. Adding
coolant to the total system volume will increase required expansion volume. This
volume is not accounted for in the expansion volume designed into the heat
exchanger cooled engine arrangement. Please see the installation drawing to
identify the supply and return locations from the engine to the vessel cabin heater.
Commission the engine first without the heat recovery system active to ensure the
engine meets application requirements. Once complete operate the engine with the
heat recovery system active. To ensure the engine is protected from over-cooling
as a result of the heat recovery system being implemented, the measured jacket
water temperature should be 70 deg C (158 deg F) or above.
COOLING SYSTEM
14
Heat Exchanger Schematic
Figure 13: Heat Exchanger Schematic
Keel Cooled Schematic
COOLING SYSTEM
Figure 14: Keel Cooled Schematic
15
Exhaust System
The C32 SCAC Engines have water cooled exhaust manifolds and turbine housings.
Exhaust Backpressure Limits

The total exhaust backpressure limit is published in TMI under Systems Data. This
level was established with an emphasis on low specific fuel consumption and
exhaust valve temperatures. Therefore, to achieve proper performance of the
engine, the exhaust backpressures must be kept below the published limit.
Vee engine exhaust piping should be designed with equal restrictions on each bank
to prevent unequal bank-to-bank backpressure.
System backpressure should be measured in a straight length of the exhaust pipe
at least three to five pipe diameters away from the last size transition from the
turbocharger outlet. System backpressure measurement is part of the engine
commissioning.
Measuring the exhaust pressure is a difficult task to get accurate. If the probe is
not perpendicular to the flow you can get higher or lower values due to a venturi or
static pressure affect across the probe. In addition if you just have a pipe probe
entering the stream it should be a minimum diameter. Probes larger than 9.5 mm
(3/8 in.) diameter can also get a venturi effect and can make the pressures read
low.
Turbochargers
Turbocharger outlet connections and geometry illustrated on the engine installation
drawings. Optional attachments such as flexible fittings (bellows), 90 degree
elbows, mufflers and spark arresting mufflers (silencers) can be ordered with the
engine.
The exhaust bellows are intended to compensate for thermal growth and
movement of the engine. The vessel exhaust system structure immediately after
the engine exhaust bellows must be a fixed/rigid point, and should not be
supported by the engine. The supplied exhaust bellows will only handle the engine
movement and thermal growth. No additional external loading is allowed on the
turbochargers.
Exhaust Piping
A common exhaust system for multiple installations is not acceptable. An exhaust
system combined with other engines allows operating engines to force exhaust
gases into engines not operating. The water vapor condenses in the cold engines
EXHAUST SYSTEM
and may cause engine damage. Additionally, soot clogs turbochargers, aftercoolers,
and cleaner elements. Valves separating engines’ exhaust systems are also
discouraged. High temperatures warp valve seats and soot deposit causes leakage.
The exhaust pipe diameter is based on engine output, gas flow, and length of pipe
and number of bends. Sharp bends should be avoided and, where necessary,
should have the largest possible radius. The minimum radius should be 1-1/2 pipe
diameters. The piping should be as short as possible and insulated. The insulation
16
should be protected by mechanical lagging to keep it intact. All flexible exhaust
fittings should be insulated using removable quilted blankets. It is recommended to
provide the system with a valve drain arrangement to prevent rainwater from
entering the engine during prolonged shutdown periods. For testing purposes, the
exhaust system must have a test port installed after the combined turbocharger
outlets. This test port should be a 10 to 13 mm (0.4 to 0.5 in.) plugged pipe
welded to the exhaust piping.
Exhaust piping must be able to expand and contract. It is required that one fixed
point be installed directly after the flexible exhaust fitting at the turbocharger
outlet. This will prevent the transmission of forces resulting from weight, thermal
expansion, or lateral displacement of the external exhaust piping from acting on the
turbocharger.
Water cooled exhaust systems are commonly used in the fast vessel industry. The
systems are designed by the yard or consultants and vary somewhat from
installation to installation. Caterpillar has no objections to these systems provided
that the engine is properly protected and the parameters as outlined are adhered to.
This is the shipyard’s responsibility.
EXHAUST SYSTEM
17
Fuel System
Tank Position
The fuel supply system must assure a continuous, clean supply of fuel. The tanks
should not exceed the height of the engine fuel injectors in order to prevent
possible leakage of fuel into the cylinders. If a higher position is required, check
valves with backpressures set to the fuel column height must be installed.
Cat fuel transfer pumps lifting capability is published in TMI under Systems Data.
Line Restriction
The internal diameter of the piping/line size supplying fuel to the engine, and the
fuel return line to the tank should be equal to or greater than the line size at the
engine connections.
Maximum inlet restriction before the transfer pump is published in Systems Data in
TMI under Systems Data.
Purge all air from the fuel system prior to starting the engine. Air in the system
causes hard starting and erratic engine operation, and can erode injectors.
Flexible Connections
Connections to the engine must be flexible, and must be connected directly at the
engine inlet and outlet to accommodate engine motion. Maximum recommended
hose length is 30 inches.
The fuel supply location on the engine is NOT service side specific. The supply is
always located on the right hand side of the engine near the water cooled engine
exhaust riser. The fuel supply fitting is a male 7/8-14 JIC.
The fuel return location on the engine is service side specific and is located on the
fuel filter base. The fuel return is always located in the aft position on the fuel filter
base. The fuel return fitting is a male 3/4-16 JIC.
The fuel line connections are located on the Engine Installation Drawings.
Fuel Cooler
The fuel cooler is standard on all commercial engines. The fuel cooler is a plate
type brazed cooler in the treated water aftercooler circuit and is located in the
cavity behind the coolant tank for the aftercooler system.
Fuel Filters
A Cat standard engine mounted fuel filtration system should be considered as a
secondary fuel filter system to the primary vessel mounted fuel filter system
installed by the vessel builder or customer. The engine mounted fuel filter system
has a duplex fuel filtration system with spin on type fuel filters. Caterpillar does not
FUEL SYSTEM
offer a simplex fuel filter system on this product.

• Duplex fuel filter systems are equipped with a diverter valve that allows the
engine operator to change the fuel filter while the engine in operation.
• Refer to SISweb for fuel filter maintenance intervals.
18
Lubrication Oil System
General
Standard engine mounted oil filters are equipped with a simplex oil filtration
system, a duplex oil filter system is optional. Each engine is equipped with one
engine mounted shell and tube oil cooler. The oil is cooled by treated water from
the jacket water circuit.
Lubrication oil filters are available as service side specific and is selected by the
dealer.
Oil Pan
All commercial ratings are equipped
with a deep sump oil pan. This
product does not have a shallow
sump option. The oil pan itself
contains an “oil cross-over tube,”
this tube is the conduit used for
transferring oil from the right side of
the engine to the left side. This tube
is needed to supply oil to the filters
mounted on the left side of the
Figure 15: Top View of Oil Pan
starboard engine.
Oil Change Intervals

Interval
Engine Rating
(Hours)
All Auxiliary Ratings 750
A - Rating 1000
B - Rating 750
C - Rating 500
LUBRICATION OIL SYSTEM
Oil Filters
The lubrication oil filters are high efficient spin-on type filters.
• Simplex oil filter systems provide standard engine oil filtration.
• Duplex oil filter systems are equipped with a diverter valve that allows the
engine operator to change the lubrication oil filter while the engine is in
operation.
• Filters have a 5 micron filter media.
19
Pre-Lubrication Recommendations
Pre-Lubrication systems can be installed by the dealer or customer as needed. Pre-
Lubrication systems are often used on large engines but they are not required for
C32 engines.
• Minimize size of the external system
• Do not introduce any foreign objects or debris to the system
• Install a check valve on the external pump outlet to engine
• Install two-way valves near the engine on the oil inlet and outlet to the
external oil pump
• Ensure lines/connections to and from the external system are leak free
• Include the added external system oil volume when filling the engine with oil
• Ensure the inlet and outlet to the pump are connected in the correct
locations from the engine the external pump
• Do not run the pre-lube oil system while the engine is running
• Use hose that is compatible with lubrication oil
Caterpillar offers a pre-lube pump and motor through Cat Parts. Part number 6N-
5599 can be used and provides a flow of 49L/min (13 gal/min).
Illustrations of external oil pump supply and return locations on the engine are
identified on the engine installation drawings.
Power Take Offs

Rear Hydraulic Pump Drives
The rear hydraulic pump drives are optional plug in drives. If rear PTO’s are required
but were not selected when the engine was ordered they can be installed by the
dealer without having to remove the flywheel housing and updating the gear train.
An SAE A and SAE B drive is available for the left and right hand side of the
engine.
Engines equipped with a Cat rear mounted sea water pump cannot be equipped
with left hand service rear hydraulic pump drives. Caterpillar does not offer
auxiliary equipment (power steering pumps, etc.) for use with the drive adapters.
POWER TAKE OFFS
The rear hydraulic pump drives rotate clockwise when viewed from the rear and
operates at 0.933 times engine speed.
20
Starting System
Air Starter Description
This air starter is a turbine driven starter motor that does not require fuel or oil
lubrication. It is supplied as a fully integrated module that includes the following
features and/or components:
• Integral Controls and Solenoid Valves
• Integral Exhaust Muffler
• Integral Electronic Controller
• Electronic Starter Protection (ESP) Logic
• Pre-Engaged Starter Pinion Gear Drive and Over-Running Clutch
The starter pinion gear is fully engaged (to the engine ring gear) before the starter
motor runs (cranks the engine). An over-running clutch provides maximum torque
delivery and added protection of the starter pinion and engine ring gear.
The integral controls include a main air relay valve, and pilot-air solenoid w/manual
bypass feature.
Integral muffler, center-diffused 360 degree muffler exhausts air at low velocity,
through three replaceable sound dampening elements, each located under a metal
guard screen.
The Integral electronic controller shares control with the engines control system, to
provide consistent, error free operation and greatest starter reliability.
Air Quality and Filtration

Upstream installation and use of a filter or Y-strainer is recommended to protect the
air starter from contaminants. Before running the starter, purge the upstream air
system to remove debris. Inspect the condition of the filter on a monthly basis or
as needed based on air quality and/or environment. Clean or replace filter as needed
to prevent flow restrictions, reduced air starter power output, and contamination of
starter controls.
Lubrication
The air starter does NOT require lubrication supply air. Therefore, the starter
exhaust does not produce an oil or diesel mist, yet may contain condensed air
system moisture and/or site air system chemicals/additives. The starter’s internal
gearbox and bearings are grease-packed and sealed.
STARTING SYSTEM
Emergency Starting
The air starter has a manual bypass button, located on the pilot air solenoid. This
allows the starter to be operated manually (without electrical power/control
voltage). Continuous manual (pneumatic) control of the starter could potentially
result in improper starter engagement. To minimize risk, it is strongly recommended
for this feature to be used only in emergencies. DO NOT routinely use the manual
bypass to operate the starter.
21
If the starter will only operate using the manual bypass, this likely indicates a
problem originating with the following:
• Pilot Air Solenoid
• Electronic Controller
• Communication with the ECM
Emergency Starting Procedure:
1. Locate the starter’s pilot air solenoid
2. Locate the button on top of the coil.
3. Using a pointed object (pen, paper clip, screw
driver), depress the button to actuate the starter.
CAUTION: The starter must never be engaged to a
running engine.
In the event of emergencies (or loss of control voltage),
use the manual bypass feature on the control solenoid to manually start the engine.
DO NOT repeatedly use the manual bypass to defeat the air starter’s control
module and engine control module. Make necessary repairs as soon as possible to
avoid repeated use of the bypass feature, as this may result in air starter or engine
damage. The starter should never be used to “bump” or “bar” the engine.
Air Starter Capacities
Minimum Recommended Maximum
2.7 Bar 6.89 Bar 10.3 Bar

Operating Air Pressure
(90 psig) (100 psig) (150 psig)
Controller/Solenoid Elec
24-volt (VDC) 24-volt (VDC) 26-volt (VDC)
Power Required.
1337 m3/hr 1437 m3/hr 2111 m3/h

Consumption
(787 scfm) (863 scfm) (1241 scfm)
Operating Temp (Ambient) -28 deg C (-20 deg F) - 93 deg C (200 deg F)
STARTING SYSTEM
22
Air Starter Installation Example
Figure 16: Air Starter Installation Example
STARTING SYSTEM
23
Mounting System
Isolator Mounts
Caterpillar offers two types of isolator mounts. A conical (non-thrust) mount and
thrust/torque mount (TT).
The non-thrust conical mount is recommended for use in non-thrust applications,
typically free standing engine arrangements with a remote gearbox (transmission).
The engine should be isolated from all thrust loads in this application. Shore
hardness or durometer for the non-thrust mount is 50.
Non-Thrust Mounts Mount Characteristics
Maximum Vertical Deflection ..................... 14 mm
Maximum Load .......................................... 19 kN
Maximum Shock Load (All Directions) .......... 70 kN
Thrust mounts are recommended in applications that transmit thrust into the
mounting system, for example, close-coupled engine and gearbox (transmission)
applications. In this circumstance the mounting system for the engine and gearbox
is subject to thrust load being transmitted through the driveline. Durometer for the
thrust mount is 70.
Thrust Mounts Mount Characteristics
Initial Load Limit
(4 mm vertical Compression) .................. 13.25 kN
Maximum Vertical Compression .............. 26.75 kN
Maximum Vertical Tension .......................... 10 kN
Maximum Thrust Load ........................... 29.75 kN
Maximum Fore Aft Shock Load ............. +/- 85 kN
Maximum Athwartship Shock Load ........ +/- 60 kN
Maximum Vertical Shock Load ....... +75/ -200 kN
MOUNTING SYSTEM
24
Engine Preservation and Packaging
The Caterpillar factory has several standard levels of engine preservation and
shipment protection. All engines that ship from the factory have plastic wrap
protection. The plastic wrap provides approximately 6 to 12 months of external
protection from moisture, sun and wind under storage conditions. If the engine is to
be stored for longer periods of time, consider specifying Storage Preservation as
described below.
Storage Preservation protects the engine and accessories from functional
deterioration for a minimum of one year. It includes standard protective measures
plus vapor corrosion inhibitor (VCI) in all internal compartments and glycol solution
in the cooling system.
Export boxing protects the engine and accessories from functional deterioration for
a minimum of one year under outside storage conditions. Including standard
protective measures, vapor corrosion inhibitor in all internal compartments. The
exterior box provides protection against mechanical damage during shipment and
storage. All marine engines are placed upon wooden skids prior to shipment. All
ship loose parts are painted and oiled and placed ship loose boxes. On arrival, open
all boxes and review their contents against the packing list. The parts should then
be repackaged and preserved for protection.
ENGINE PRESERVATION AND PACKAGING
25
Shipbuilder’s Responsibility
Unless otherwise specified, the engine buyer shall be responsible for the following:
• Ensure all coolant, lube oil piping, fuel oil piping, exhaust piping and intake
air ducting are free of rust, scale, weld spatter and foreign material prior to
startup of the engines.
• Provide electrical wiring and the necessary piping to the engine, i.e., exhaust
piping, fuel oil piping to and from the engine, air piping to the starting
motor(s), air filter ducting/piping, crankcase fumes disposal ducting, etc. All
of the above noted interconnections need to be designed in such a way so
as to comply with acceptable vibratory levels of excitation throughout the
entire range of engine operation. No primary resonances in the interface
hardware are acceptable.
• Furnish and install standby pumps as required by Marine classification
societies.
• Install adequate engine foundation and provide proper chocking and
alignment between the engine and marine gear.
• Provide adequate clearance for disassembly of engine (i.e. overhead
clearance for connecting rods and piston removal can be found in the
Serviceability Considerations Application and Installation (A&I) Guide
LEGM4735).
• Provide primary fuel filtration system.
• Provide all labor, equipment and hardware to install the equipment.
• Furnish accurate data for a torsional vibration analysis.
• Provide all coolants, water treatment chemicals (if used), lubricating oil, and
fuel oils necessary to operate the engine.
• Warehouse and protect engines, accessories and miscellaneous ship loose
equipment until their installation. Cat engines are protected against corrosion
for inside dry storage for a period up to six months. Provisions for additional
storage periods are available from the factory.
SHIPBUILDER’S RESPONSIBILITY
26
Reference Material
The following information is provided as additional reference to subjects discussed
in this guide.
LEGM4735
Serviceability Considerations Application and Installation (A&I) Guide
The product price list can be accessed

https://engines.cat.com/marine
online through Power Net.
Marine Product Application and
Installation webpage can also be https://engines.cat.com/marine/application
accessed via Power Net.
Engine Installation drawings can be
retrieved from the Engine Drawing
Design Center (EDDC). A paid https://enginedrawings.cat.com/
subscription is required to download
drawings from this site.
Technical Marketing Information (TMI)
/ engine performance data can be http://tmiweb.cat.com/
obtained from TMI Web.
Service and maintenance information
can be obtained from the Service https://sis.cat.com/
Information System (SIS Web)
REFERENCE MATERIAL
27
LEBM0009-01 ©2013 Caterpillar Printed in U.S.A.
All rights reserved.

C32 Project Guide 1 PDF

Uploaded by

Copyright:

Available Formats

C32 Project Guide 1 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

C32 Project Guide 1 PDF

Uploaded by

Copyright:

Available Formats

©2009 Caterpillar® All rights reserved.

Air System ........................................................................... 7

Cooling System .................................................................... 9

Exhaust System .................................................................. 16

©2013 Caterpillar All rights reserved.

Lubrication Oil System........................................................ 19

Power Take Offs ................................................................. 20

Starting System ................................................................. 21

Mounting System ............................................................... 24

Engine Preservation and Packaging..................................... 25

©2013 Caterpillar All rights reserved.

Product Identification Information

Marine (Auxiliary) Gen Set Engine Price List C32 MGE3MC

Note: The following images may not reflect your engine.

Heat Exchanger Cooled Engine (Rear Mounted Sea Water Pump)

Figure 1: Front View

Figure 2: Left View

Figure 4: Right View

Note: The following images may not reflect your engine.

Figure 5: Front View

Figure 6: Left View

Figure 8: Right View

Note: The following image may not reflect your engine.

Heat Exchanger Cooled Engine (Front Mounted Sea Water Pump)

Figure 9: Front View

Crankcase Fumes Disposal

Crankcase Piping System

Coolant Flow Control

Coolant Temperature Control

Treated Water Pumps

Sea Water Pump

Engine Mounted Shunt Tanks and Venting

Heat Exchanger Cooled Engines

Keel Cooled Engines

Cold Starting (Jacket Water Heaters)

This allows accurate documentation of the cooling system during the

Water Quality, Rust Inhibitors, and Antifreeze

components. Caterpillar has coolant inhibitor available to properly condition the

The vessel mounted coolant

Keel cooled engines include two

Heat Recovery (Cabin Heater)

Figure 13: Heat Exchanger Schematic

Keel Cooled Schematic

Figure 14: Keel Cooled Schematic

Exhaust Backpressure Limits

offer a simplex fuel filter system on this product.

Oil Change Intervals

Power Take Offs

Air Quality and Filtration

Air Starter Capacities

Minimum Recommended Maximum

2.7 Bar 6.89 Bar 10.3 Bar

1337 m3/hr 1437 m3/hr 2111 m3/h

Figure 16: Air Starter Installation Example

ENGINE PRESERVATION AND PACKAGING

The product price list can be accessed

You might also like