Issued Date: 20, Jun 2008

Model No.: V260B1 – L12

Approval

TFT LCD Approval Specification

MODEL NO.: V260B1 – L12

Customer:

Approved by:
Note:

www.jxlcd.com
www.jxlcd.com

TV Head Division
Approved By
LY Chen

QA Dept. Product Development Div.

Reviewed By
Tomy Chen WT Lin

LCD TV Marketing and Product Management Div.

Prepared By
WY Li Chloe Chen

1
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

- CONTENTS -
REVISION HISTORY ------------------------------------------------------- 3

1. GENERAL DESCRIPTION ------------------------------------------------------- 4

1.1 OVERVIEW
1.2 FEATURES
1.3 APPLICATION
1.4 GENERAL SPECIFICATIONS
1.5 MECHANICAL SPECIFICATIONS

2. ABSOLUTE MAXIMUM RATINGS ------------------------------------------------------- 5

2.1 ABSOLUTE RATINGS OF ENVIRONMENT
2.2 ELECTRICAL ABSOLUTE RATINGS
2.2.1 TFT LCD MODULE
2.2.2 BACKLIGHT UNIT

3. ELECTRICAL CHARACTERISTICS ------------------------------------------------------- 7

3.1 TFT LCD MODULE
3.2 BACKLIGHT INVERTER UNIT
3.2.1 CCFL(Cold Cathode Fluorescent Lamp) CHARACTERISTICS
3.2.2 INVERTER CHARACTERISTICS
3.2.3 INVERTER INTERTFACE CHARACTERISTICS

4. BLOCK DIAGRAM ------------------------------------------------------- 12

4.1 TFT LCD MODULE

5. INTERFACE PIN CONNECTION ------------------------------------------------------- 13

5.1 TFT LCD MODULE
5.2 BACKLIGHT UNIT

www.jxlcd.com
www.jxlcd.com
5.3 INVERTER UNIT
5.4 BLOCK DIAGRAM OF INTERFACE
5.5 LVDS INTERFACE
5.6 COLOR DATA INPUT ASSIGNMENT

6. INTERFACE TIMING ------------------------------------------------------- 19

6.1 INPUT SIGNAL TIMING SPECIFICATIONS
6.2 POWER ON/OFF SEQUENCE

7. OPTICAL CHARACTERISTICS ------------------------------------------------------- 22

7.1 TEST CONDITIONS
7.2 OPTICAL SPECIFICATIONS

8. DEFINITION OF LABELS ------------------------------------------------------- 26

8.1 CMO MODULE LABEL

9. PACKAGING ------------------------------------------------------- 27
9.1 PACKING SPECIFICATIONS
9.2 PACKING METHOD

10. PRECAUTIONS ------------------------------------------------------- 30

10.1 ASSEMBLY AND HANDLING PRECAUTIONS
10.2 SAFETY PRECAUTIONS
10.3 STORAGE PRECAUTIONS

11. REGULATORY STANDARD -------------------------------------------------------- 32

11.1 SAFETY

12. MECHANICAL CHARACTERISTICS ------------------------------------------------------- 33

2
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

REVISION HISTORY
Page
Version Date Section Description
(New)
Ver 2.0 23, May ’08 All All Approval Specification was first issued.
Ver 2.1 20, Jun ‘08 11 3.2.3 Modify inverter interface characteristics:
12 3.2.3 Tr1 max value from 50ms to NC
Tf1 max value from 50ms to NC
Tpwm max value from 500ms to NC
Ton max value from 500ms to NC
Toff max value from 500ms to NC

www.jxlcd.com
www.jxlcd.com

3
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

1. GENERAL DESCRIPTION
1.1 OVERVIEW
V260B1- L12 is a TFT Liquid Crystal Display module with 5U-CCFL Backlight unit and 1ch-LVDS
interface. The display diagonal is 26”. This module supports 1366 x 768 WXGA format and can display
16.2M colors (6-bit+FRC colors). The inverter module for backlight is built-in.

1.2 FEATURES
- Excellent Brightness 500nits
- Contrast Ratio 800:1
- Fast Response Time (8ms)
- Color Saturation NTSC 72%
- WXGA (1366 x 768 pixels) Resolution
- DE (Data Enable) Only Mode
- LVDS (Low Voltage Differential Signaling) Interface
- Viewing Angle: 160(H)/150(V) (CR>10) TN Technology
-Color Reproduction (Nature Color)

1.3 APPLICATION
- TFT LCD TVs

www.jxlcd.com
www.jxlcd.com
- High Brightness, Multi-Media Displays

1.4 GENERAL SPECIFICATI0NS

Item Specification Unit Note
Active Area 575.769 (H) x 323.712 (V) (26” Diagonal) mm
(1)
Bezel Opening Area 580.8 (H) x 328.8 (V) mm
Driver Element a-si TFT Active Matrix

Pixel Number 1366 x R.G.B. x 768 pixel
Pixel Pitch (Sub Pixel) 0.1405 (H) x 0.4215 (V) mm
Pixel Arrangement RGB Vertical Stripe

Display Colors 16.2M color
Display Operation Mode Transmissive Mode / Normally White

Anti-Glare Coating (Haze 25%)

Surface Treatment
Hard Coating (3H)

1.5 MECHANICAL SPECIFICATIONS

Item Min. Typ. Max. Unit Note
Horizontal(H) 625 626 627 mm
Vertical(V) 372 373 374 mm
Module Size
Depth(D) 31 32 33 mm To Rear
Depth(D) 45.7 46.7 47.7 mm To Inverter Cover
Weight
4200
g
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.

4
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

2. ABSOLUTE MAXIMUM RATINGS

2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Value
Item Symbol Unit Note
Min. Max.
Storage Temperature TST -20 +60 ºC (1)
Operating Ambient Temperature TOP 0 +50 ºC (1), (2)
Shock (Non-Operating) SNOP
50 G (3), (5)
Vibration (Non-Operating) VNOP
1.0 G (4), (5)
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta
40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The maximum operating temperature is based on the test condition that the surface temperature of
display area is less than or equal to 65 ºC with LCD module alone in a temperature controlled chamber.
Thermal management should be considered in final product design to prevent the surface temperature of
display area from being over 65 ºC. The range of operating temperature may degrade in case of improper
thermal management in final product design.
Note (3) 11 ms, half sine wave, 1 time for ± X, ± Y, ± Z.
Note (4) 10 ~ 500 Hz, 10 min, 1 time each X, Y, Z.
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough

www.jxlcd.com
www.jxlcd.com
so that the module would not be twisted or bent by the fixture.

Relative Humidity (%RH)

100
90

80

60
Operating Range

40

20
10 Storage Range

-40 -20 0 20 40 60 80

Temperature (ºC)

5
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

2.2 ELECTRICAL ABSOLUTE RATINGS

2.2.1 TFT LCD MODULE
Value
Item Symbol Unit Note
Min. Max.
Power Supply Voltage Vcc -0.3 13.0 V
(1)
Input Signal Voltage VIN -0.3 3.6 V

2.2.2 BACKLIGHT UNIT

Test
Item Symbol Min. Type Max. Unit Note
Condition
Lamp Voltage VW Ta = 25 

3000 VRMS
Power Supply Voltage VBL
0
30 V (1)
Control Signal Level

-0.3
7 V (1), (3)

Note (1) Permanent damage to the device may occur if maximum values are exceeded. Functional
operation should be restricted to the conditions described under normal operating conditions.
Note (2) No moisture condensation or freezing.
Note (3) The control signals includes Backlight On/Off Control, Internal PWM Control and External PWM
Control.

www.jxlcd.com
www.jxlcd.com

6
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE Ta = 25 ± 2 ºC
Value
Parameter Symbol Unit Note
Min. Typ. Max.
Power Supply Voltage VCC 11.4 12.0 12.6 V (1)
Power Supply Ripple Voltage VRP

300 mV
Rush Current IRUSH

3.0 A (2)
White
0.2 0.25 A
Power Supply Current Black ICC
0.5 0.55 A (3)
Vertical Stripe
0.4 0.45 A
Differential Input High
VLVTH

+100 mV
Threshold Voltage
LVDS
Differential Input Low
Interface VLVTL -100

mV
Threshold Voltage
Common Input Voltage VLVC 1.125 1.25 1.375 V
Terminating Resistor RT
100
ohm
CMOS Input High Threshold Voltage VIH 2.7
3.3 V
interface Input Low Threshold Voltage VIL 0
0.7 V
Note (1) The module should be always operated within above ranges.
Note (2) Measurement Conditions:
+12.0V
Q1 AO4409

Vcc
C3
FUSE (LCD Module Input)

R1 1uF

www.jxlcd.com
www.jxlcd.com 200K

VR1

47K

(Low to High)
(Control Signal)
R2
Q2 C1
SW
2N7002
1K
10uF

Vcc rising time is 470us

+12V

0.9Vcc

0.1Vcc

GND
470us

7
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

Note (3) The specified power supply current is under the conditions at Vcc = 12 V, Ta = 25 ± 2 ºC, f v = 60
Hz, whereas a power dissipation check pattern below is displayed.

a. White Pattern b. Black Pattern

Active Area Active Area

c. Vertical Stripe Pattern

R G B R G B

B R G B R G B R

www.jxlcd.com
www.jxlcd.com B R G B R G B R

R G B R G B

Active Area

3.2 BACKLIGHT INVERTER UNIT

3.2.1 CCFL (Cold Cathode Fluorescent Lamp) CHARACTERISTICS (Ta = 25 ± 2 ºC)
Value
Parameter Symbol Unit Note
Min. Typ. Max.
Lamp Voltage VW
1688
VRMS IL = 7.5mA
Lamp Current IL 7.0 7.5 8.0 mARMS (1)


2830 VRMS (2), Ta = 0 ºC
Lamp Starting Voltage VS


2410 VRMS (2), Ta = 25 ºC
Operating Frequency FO 40
80 KHz (3)
Lamp Life Time LBL 50,000 60,000
Hrs (4)

8
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

3.2.2 INVERTER CHARACTERISTICS (Ta = 25 ± 2 ºC)

Value
Parameter Symbol Unit Note
Min. Typ. Max.
Power Consumption PBL
66
W (5)(6), IL = 7.5mA
Input Voltage VBL 22.8 24 25.2 VDC
Input Current IBL
2.75
A Non Dimming
Input Inrush Current


4.3 Apeak VBL =24.0V
Input Ripple Noise
-

912 mVP-P VBL =22.8V
Oscillating Frequency FW 63 66 69 kHz
Dimming Frequency FB 140 165 190 Hz
Minimum Duty Ratio DMIN
20
%

Note (1) Lamp current is measured by utilizing high frequency current meters as shown below:

HV (Pink)
A 1
HV (White)
A 2

HV (Pink)
A 1
HV (White)

www.jxlcd.com
A 2

www.jxlcd.com
LCD
Module
A
A
HV (Pink)
HV (White)
1
2 Inverter

HV (Pink)
A 1
HV (White)
A 2

HV (Pink)
A 1
HV (White)
A 2

Note (2) The lamp starting voltage VS should be applied to the lamp for more than 1 second under starting
up duration. Otherwise the lamp could not be lighted on completed.
Note (3) The lamp frequency may produce interference with horizontal synchronous frequency from the
display, and this may cause line flow on the display. In order to avoid interference, the lamp
frequency should be detached from the horizontal synchronous frequency and its harmonics as far
as possible.

9
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

Note (4) The life time of a lamp is defined as when the brightness is larger than 50% of its original value
and the effective discharge length is longer than 80% of its original length (Effective discharge
length is defined as an area that has equal to or more than 70% brightness compared to the
brightness at the center point.) as the time in which it continues to operate under the condition Ta
= 25 2 and IL = 7.0~ 8.0mARMS.

Note (5) The power supply capacity should be higher than the total inverter power consumption PBL. Since
the pulse width modulation (PWM) mode was applied for backlight dimming, the driving current
changed as PWM duty on and off. The transient response of power supply should be considered
for the changing loading when inverter dimming.
Note (6) The measurement of Max. value is based on 26” backlight unit under 24V input voltage and 7.8mA
lamp in average after lighting for 30 minutes.
Note (7) 10% minimum duty ratio is only valid for electrical operation.

3.2.3 INVERTER INTERTFACE CHARACTERISTICS

Test
Item Symbol Min. Typ. Max. Unit Note
Condition

Error Signal ERR




(Note 2)

www.jxlcd.com
www.jxlcd.com
On/Off Control
Voltage

Internal PWM
Control Voltage
ON
OFF
MAX
VBLON

VIPWM

2.0
0
3.0




3.15
5.0
0.8
3.3
V
V
V Maximum Duty Ratio
MIN
0
V Minimum Duty Ratio
External PWM HI 2.0
5.0 V Duty On
VEPWM

Control Voltage LO 0
0.8 V Duty Off
VBL Rising Time Tr1
30
 ms
VBL Falling Time Tf1
30
 ms
Control Signal Rising Time Tr


100 ms
Control Signal Falling Time Tf


100 ms
PWM Signal Rising Time TPWMR


50 us
PWM Signal Falling Time TPWMF


50 us
Input Impedance RIN
1

M
PWM Delay Time TPWM 100
ms
BLON Delay Time Ton
300

ms
BLON Off Time Toff
300

ms
Note (1) The power sequence and control signal timing as shown in following figure.
Note (2) When inverter protective function is triggered, ERR will output open collector status. In normal
operation, the signal of ERR will output a low level voltage.

10
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

Note (3) While system is turned ON or OFF, the power sequences must follow as below descriptions:
Turn ON sequence: VBL
> PWM signal
> BLON
Turn OFF sequence: BLOFF
> PWM signal
> VBL

Tr1 Tf1
VBL

0 Ton Toff
VBLON 2.0V
0.8V
0
Backlight on duration
Tr Tf

Ext. Dimming Function

TPWMR
2.0V T PWMF
VEPWM
0.8V
Floating

www.jxlcd.com
0

VIPWM

0
www.jxlcd.com
3.3V
TPWM

Floating Int. Dimming Function

VW

External External
PWM PWM Duty
Period

100% Minimun Duty

11
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

4. BLOCK DIAGRAM
4.1 TFT LCD MODULE

SCAN DRIVER IC
RX0(+/-)
TFT LCD PANEL
(P-TWO,196185-30041)

(1366x3x768)
INPUT CONNECTOR

RX1(+/-)

RX2(+/-)
TIMING
RX3(+/-)

RXCLK(+/-)
CONTROLLER
Vcc
DATA DRIVER IC
GND
DC/DC CONVERTER &
REFERENCE VOLTAGE

CN2-CN6 :
CP042EP1MFB-LF (CviLux)
or equivalent BACKLIGHT
CN1 INVERTER CONNECTOR UNIT
VBL CN1 :
GND 1. S14B-PHA-SM-TB(LF)(SN) (JST)
ERR
BLON
I_PWM
E_PWM

www.jxlcd.com
www.jxlcd.com

12
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

5. INTERFACE PIN CONNECTION

5.1 TFT LCD MODULE
CNF1 Connector Pin Assignment
Pin No. Symbol Description Note
1 VCC Power supply: +12V
2 VCC Power supply: +12V
3 VCC Power supply: +12V
4 VCC Power supply: +12V
5 GND Ground
6 GND Ground
7 GND Ground
8 GND Ground
9 SELLVDS Select LVDS data format (2)
10 NC No connection (3)
11 GND Ground
12 RX0- Negative transmission data of pixel 0
13 RX0+ Positive transmission data of pixel 0
14 GND Ground
15 RX1- Negative transmission data of pixel 1
16 RX1+ Positive transmission data of pixel 1
17 GND Ground
18 RX2- Negative transmission data of pixel 2
19 RX2+ Positive transmission data of pixel 2
20 GND Ground
21 RXCLK- Negative of clock
22
23
24
25
www.jxlcd.com
www.jxlcd.com
RXCLK+
GND
RX3-
RX3+
Positive of clock
Ground
Negative transmission data of pixel 3
Positive transmission data of pixel 3
26 GND Ground
27 NC No connection (3)
28 NC No connection (3)
29 GND Ground
30 GND Ground
Note (1) Connector Part No.: P-TWO,196185-30041 or compatible
Note (2) Ground or OPEN: Normal, High: JEIDA LVDS format
Please refer to 5.5 LVDS INTERFACE (Page 17)
Note (3) Reserved for internal use. Please leave it open.

13
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

5.2 BACKLIGHT UNIT

The pin configuration for the housing and leader wire is shown in the table below.
CN2-CN6 (Housing) : CP042ESFA00 (CviLux) or equivalent.
Pin No. Symbol Description Wire Color
1 HV High Voltage Pink
2 HV High Voltage White
Note (1) The backlight interface housing for high voltage side is a model CP042ESFA00 (CviLux) or equivalent.
The mating header on inverter part number is CP042EP1MFB-LF (CyiLux) or equivalent.

5 Male Connectors
CP042ESFA00(CviLux)
Or Equivalent

1.HV(Pink,+)

2.HV(White,-)

1.HV(Pink,+)

2.HV(White,-)

www.jxlcd.com
www.jxlcd.com 1.HV(Pink,+)

2.HV(White,-)

1.HV(Pink,+)

2.HV(White,-)

1.HV(Pink,+)

2.HV(White,-)

14
Version 2.1
 Issued Date: 20, Jun 2008
Model No.: V260B1 – L12
Approval

5.3 INVERTER UNIT

CN1 (Header) : 1. S14B-PHA-SM-TB(LF)(SN) (JST)
Pin No. Symbol Description
1
2
3 VBL +24V Power input
4
5
6
7
8 GND Ground
9
10
Normal (GND)
11 ERR
Abnormal(Open collector)
12 BLON BL ON/OFF
13 I_PWM Internal PWM Control
14 E_PWM External PWM Control
Notice:
#PIN 13:Analog Dimming Control (Use Pin 13) : 0V~3.3V and Pin 14 must open.
#PIN 14:PWM Dimming Control (Use Pin 14) : Pin 13 must open.
#Pin 13 (I_PWM) and Pin 14 (E_PWM) can not open in same period.

CN2-CN6 (Header) : CP042EP1MFB-LF (Cvilux) or equivalent.

Pin
1
2
www.jxlcd.com
www.jxlcd.com
Name
CCFL HOT
Description
CCFL High Voltage
CCFL HOT CCFL High Voltage

15
Version 2.1
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

5.4 BLOCK DIAGRAM OF INTERFACE

CNF1

Rx0+ 51

100pF RxOUT
TxIN Rx0- R0-R7
R0-R7 51

Rx1+ 51
G0-G7
G0-G7 100pF
Rx1-
51
B0-B7
B0-B7
Rx2+ 51

DE Rx2-
100pF
DE
51

Rx3+ 51

100pF
Rx3-
51

Host
CLK+ 51

Graphics PLL 100pF
DCLK
CLK- PLL
Controller 51

Timing
Controller
LVDS Transmitter LVDS Receiver

www.jxlcd.com
www.jxlcd.com
THC63LVDM83A
(LVDF83A)
THC63LVDF84A

R0~R7 : Pixel R Data

G0~G7 : Pixel G Data
B0~B7 : Pixel B Data
DE : Data Enable Signal

Note (1) The system must have the transmitter to drive the module.
Note (2) LVDS cable impedance shall be 50 ohms per signal line or about 100 ohms per twist-pair line when it is
used differentially.

16
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

5.5 LVDS INTERFACE

TRANSMITTER INTERFACE RECEIVER TFT CONTROL

SIGNAL
THC63LVDM83A CONNECTOR THC63LVDF84A INPUT

SELLVD= SELLVDS SELLVD= SELLVDS

PIN INPUT Host TFT-LCD PIN OUTPUT
L or OPEN =H L or OPEN =H
R0 R2 51 TxIN0 27 Rx OUT0 R0 R2
R1 R3 52 TxIN1 29 Rx OUT1 R1 R3
R2 R4 54 TxIN2 TA OUT0+ Rx 0+ 30 Rx OUT2 R2 R4
R3 R5 55 TxIN3 32 Rx OUT3 R3 R5
R4 R6 56 TxIN4 33 Rx OUT4 R4 R6
R5 R7 3 TxIN6 TA OUT0- Rx 0- 35 Rx OUT6 R5 R7
G0 G2 4 TxIN7 37 Rx OUT7 G0 G2
G1 G3 6 TxIN8 38 Rx OUT8 G1 G3
G2 G4 7 TxIN9 39 Rx OUT9 G2 G4
G3 G5 11 TxIN12 TA OUT1+ Rx 1+ 43 Rx OUT12 G3 G5
G4 G6 12 TxIN13 45 Rx OUT13 G4 G6
G5 G7 14 TxIN14 46 Rx OUT14 G5 G7
B0 B2 15 TxIN15 TA OUT1- Rx 1- 47 Rx OUT15 B0 B2
B1 B3 19 TxIN18 51 Rx OUT18 B1 B3
24
bit
B2
B3
B4
www.jxlcd.com
www.jxlcd.com
B4
B5
B6
20
22
23
TxIN19
TxIN20
TxIN21 TA OUT2+ Rx 2+
53
54
55
Rx OUT19
Rx OUT20
Rx OUT21
B2
B3
B4
B4
B5
B6
B5 B7 24 TxIN22 1 Rx OUT22 B5 B7
DE DE 30 TxIN26 6 Rx OUT26 DE DE
R6 R0 50 TxIN27 TA OUT2- Rx 2- 7 Rx OUT27 R6 R0
R7 R1 2 TxIN5 34 Rx OUT5 R7 R1
G6 G0 8 TxIN10 41 Rx OUT10 G6 G0
G7 G1 10 TxIN11 42 Rx OUT11 G7 G1
B6 B0 16 TxIN16 TA OUT3+ Rx 3+ 49 Rx OUT16 B6 B0
B7 B1 18 TxIN17 50 Rx OUT17 B7 B1
RSVD 1 RSVD 1 25 TxIN23 2 Rx OUT23 NC NC
RSVD 2 RSVD 2 27 TxIN24 TA OUT3- Rx 3- 3 Rx OUT24 NC NC
RSVD 3 RSVD 3 28 TxIN25 5 Rx OUT25 NC NC
DCLK 31 TxCLK IN TxCLK OUT+ RxCLK IN+ 26 RxCLK OUT DCLK
TxCLK OUT- RxCLK IN-
R0~R7: Pixel R Data (7; MSB, 0; LSB)
G0~G7: Pixel G Data (7; MSB, 0; LSB)
B0~B7: Pixel B Data (7; MSB, 0; LSB)
DE : Data enable signal
Notes(1) RSVD(reserved)pins on the transmitter shall be “H” or “L”.

17
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

5.6 COLOR DATA INPUT ASSIGNMENT

The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for
the color. The higher the binary input, the brighter the color. The table below provides the assignment of
color versus data input.
Data Signal
Color Red Green Blue
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Basic Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Colors Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Red(0) / Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(1) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(2) 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Gray
: : : : : : : : : : : : : : : : : : : : : : : : :
Scale
: : : : : : : : : : : : : : : : : : : : : : : : :
Of
Red
www.jxlcd.com
www.jxlcd.com
Red(253)
Red(254)
Red(255)
Green(0) / Dark 0
1
1
1
1
1
1
0
1
1
1
0
1
1
1
0
1
1
1
0
1
1
1
0
0
1
1
0
1 0 0 0 0
0 0 0 0 0
1 0 0 0 0
0 0 0 0 0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0 0
0 0
0 0
0
0
0
0
0
0
0
0
0
0
0
0
0 0 0
0 0 0
0 0 0
0 0 0
Green(1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
Green(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
Gray
: : : : : : : : : : : : : : : : : : : : : : : : :
Scale
: : : : : : : : : : : : : : : : : : : : : : : : :
Of
Green(253) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0
Green
Green(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
Green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Blue(0) / Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue(1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
Blue(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
Gray
: : : : : : : : : : : : : : : : : : : : : : : : :
Scale
: : : : : : : : : : : : : : : : : : : : : : : : :
Of
Blue(253) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1
Blue
Blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
Blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Note (1) 0: Low Level Voltage, 1: High Level Voltage

18
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
Frequency 1/Tc 60 76 82 MHZ
LVDS Receiver Clock Input cycle to
Trcl

200 ps
cycle jitter
Setup Time Tlvsu 600

ps
LVDS Receiver Data
Hold Time Tlvhd 600

ps
Frame Rate Fr5 47 50 53 Hz
Fr6 57 60 63 Hz
Vertical Active Display Term Total Tv 778 806 888 Th Tv=Tvd+Tvb
Display Tvd 768 768 768 Th -
Blank Tvb 10 38 120 Th -
Total Th 1442 1560 1936 Tc Th=Thd+Thb
Horizontal Active Display Term Display Thd 1366 1366 1366 Tc -
Blank Thb 76 194 570 Tc -
Note (1) Since this module is operated in DE only mode, Hsync and Vsync input signals should be set to
low logic level. Otherwise, this module would operate abnormally.

www.jxlcd.com
INPUT SIGNAL TIMING DIAGRAM

www.jxlcd.com Tv
Tvd
Tvb

DE
Th

DCLK

Tc
Thd
Thb
DE

DATA Valid Display Data (1366 clocks)

19
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

LVDS RECEIVER INTERFACE TIMING DIAGRAM

Tc

RXCLK+/-

RXn+/-

Tlvsu

Tlvhd

1T 3T 5T 7T 9T 11T 13T
14 14 14 14 14 14 14

www.jxlcd.com
www.jxlcd.com

20
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

6.2 POWER ON/OFF SEQUENCE

To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the
diagram below.

Power Supply 0.9 VCC 0.9 VCC

VCC
0.1VCC 0.1Vcc
0V

0.5
T1
10 ms T1 T3
0
T2
50 ms
0
T3
50 ms
1s
T4 T2 T4

VALID
Signals
0V

Power On Power Off

Backlight (Recommended) 50% 50%

500 msT5
100 ms
T6

www.jxlcd.com
www.jxlcd.com T5 T6

Power ON/OFF Sequence

Note (1) The supply voltage of the external system for the module input should follow the definition of Vcc.
Note (2) Apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD
operation or the LCD turns off before the backlight turns off, the display may momentarily become
abnormal screen.
Note (3) In case of Vcc is in off level, please keep the level of input signals on the low or high impedance.
Note (4) T4 should be measured after the module has been fully discharged between power off and on period.
Note (5) Interface signal shall not be kept at high impedance when the power is on.

21
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Symbol Value Unit
o
Ambient Temperature Ta 25±2 C
Ambient Humidity Ha 50±10 %RH
Supply Voltage VCC 12.0 V
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
Lamp Current IL 7.5 ± 0.5 mA
Oscillating Frequency (Inverter) FW 66 ± 3 KHz
Vertical Frame Rate Fr 60 Hz

7.2 OPTICAL SPECIFICATIONS

The relative measurement methods of optical characteristics are shown in 7.2. The following items should be
measured under the test conditions described in 7.1 and stable environment shown in Note (6).
Item Symbol Condition Min. Typ. Max. Unit Note
Contrast Ratio CR 600 800 - (2)
TR 3 5
Response Time ms (3)
TF 5 8
Center Luminance of White LC 400 500 (4)
White Variation δW 1.3 - (7)
Cross Talk CT 4 % (5)

www.jxlcd.com
www.jxlcd.com
Red

Green
Rx
Ry
Gx
θx=0°, θY =0°
Viewing Angle at
Normal Direction
0.639
0.331
0.274
-
-
-
Gy Typ. 0.596 Typ. -
(6)
Color Bx -0.03 0.151 +0.03 -
Chromaticity Blue
By 0.065 -
Wx 0.280 -
White
Wy 0.285 -
NTSC
Color Gamut CG 68 72 %
Ratio
θx+ 70 80
Horizontal
Viewing θx- 70 80
CR≥10 Deg. (1)
Angle θY + 70 80
Vertical
θY - 60 70

22
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

Note (1) Definition of Viewing Angle (θx, θy):

Viewing angles are measured by EZ-Contrast 160R (Eldim)

Normal
θx = θy = 0º

θy- θy+

θX- = 90º x- 12 o’clock direction

y+
θx− θy+ = 90º
θx+

6 o’clock
y- x+ θX+ = 90º
θy- = 90º

Note (2) Definition of Contrast Ratio (CR):

The contrast ratio can be calculated by the following expression.
Contrast Ratio (CR) = L255 / L0

www.jxlcd.com
www.jxlcd.com
L255: Luminance of gray level 255
L 0: Luminance of gray level 0
CR = CR (5),
CR (X) is corresponding to the Contrast Ratio of the point X at the figure in Note (7).

Note (3) Definition of Response Time (TR, TF):

Gray Level 255 Gray Level 255

100%
90%

Optical
Gray Level 0
Response
10%
0%

Time
TF
TR

23
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

Note (4) Definition of Luminance of White (LC):

Measure the luminance of gray level 255 at center point and 5 points
LC = L (5)
L (X) is corresponding to the luminance of the point X at the figure in Note (7).

Note (5) Definition of Cross Talk (CT):

CT = | YB – YA | / YA × 100 (%)
Where:
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)

(0, 0) Active Area (0, 0)

Active Area
YA, U (D/2,W/8) YB, U (D/2,W/8)
(D/4,W/4)

YA, L (D/8,W/2) YB, L (D/8,W/2) YB, R (7D/8,W/2)

Gray 128 Gray 0
YA, R (7D/8,W/2)
(3D/4,3W/4)
YA, D (D/2,7W/8)
YB, D (D/2,7W/8) Gray 128
(D,W) (D,W)

www.jxlcd.com
www.jxlcd.com
Note (6) Measurement Setup:
The LCD module should be stabilized at given temperature for 1 hour to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be
executed after lighting Backlight for 1 hour in a windless room.

LCD Module

LCD Panel

Center of the Screen Display Color Analyzer

(Minolta CA210)

Light Shield Room

(Ambient Luminance < 2 lux)

24
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

Note (7) Definition of White Variation (δW):

Measure the luminance of gray level 255 at 5 points
δW = Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)]

Horizontal Line
D
D/4 D/2 3D/4
Vertical Line

W/4 1 2

W W/2 5 X : Test Point

X=1 to 5

3W/4 3 4

Active Area

www.jxlcd.com
www.jxlcd.com

25
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

8. DEFINITION OF LABELS
8.1 CMO MODULE LABEL
The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation.

V260B1 -L12 Rev. XX

CHI MEI
OPTOELECTRONICS

XXXXXXXYMDLNNNN RoHS

(a) Model Name: V260B1-L12

(b) Revision: Rev. XX, for example: A0, A1… B1, B2… or C1, C2…etc.
(c) Serial ID: X X X X X X X Y M D L N N N N

Serial No.

Product Line

Year, Month, Date

www.jxlcd.com
www.jxlcd.com CMO Internal Use

CMO Internal Use

Revision

CMO Internal Use

Serial ID includes the information as below:
(a) Manufactured Date: Year: 1~9, for 2001~2009
Month: 1~9, A~C, for Jan. ~ Dec.
Day: 1~9, A~Y, for 1st to 31st, exclude I ,O, and U.
(b) Revision Code: Cover all the change
(c) Serial No.: Manufacturing sequence of product
(d) Product Line: 1 -> Line1, 2 -> Line 2, …etc.

26
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

9. PACKAGING
9.1 PACKING SPECIFICATIONS
(1) 6 LCD TV Modules / Carton
(2) Carton Dimensions : 713(L) X 429 (W) X 453 (H)
(3) Weight : Approximately 29 Kg ( 6 Modules Per Carton)

9.2 PACKING METHOD

Figures 9-1 and 9-2 are the packing method

LCD TV Module

Anti-Static Bag

Cushion(Bottom)

www.jxlcd.com
www.jxlcd.com
2 pcs Drier

Carton
Carton Label

Figure.9-1 packing method

27
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

Sea / Land Transportation (40ft HQ Container)

www.jxlcd.com
www.jxlcd.com
Sea / Land Transportation (40ft Container)

PE Sheet

28
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

Air Transportation

Corner Protector

Figure. 9-2 packing method

www.jxlcd.com
www.jxlcd.com

29
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

10. PRECAUTIONS
10.1 ASSEMBLY AND HANDLING PRECAUTIONS
(1) Do not apply rough force such as bending or twisting to the module during assembly.
(2) It is recommended to assemble or to install a module into the user’s system in clean working areas.
The dust and oil may cause electrical short or worsen the polarizer.
(3) Do not apply pressure or impulse to the module to prevent the damage of LCD panel and backlight.
(4) Always follow the correct power-on sequence when the LCD module is turned on. This can prevent the
damage and latch-up of the CMOS LSI chips.
(5) Do not plug in or pull out the I/F connector while the module is in operation.
(6) Do not disassemble the module.
(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and
easily scratched.
(8) Moisture can easily penetrate into LCD module and may cause the damage during operation.
(9) High temperature or humidity may deteriorate the performance of LCD module. Please store LCD
modules in the specified storage conditions.
(10) When ambient temperature is lower than 10ºC, the display quality might be reduced. For example, the
response time will become slow, and the starting voltage of CCFL will be higher than that of room
temperature.

www.jxlcd.com
www.jxlcd.com
10.2 SAFETY PRECAUTIONS
(1) The startup voltage of a backlight is over 1000 Volts. It may cause an electrical shock while assembling
with the inverter. Do not disassemble the module or insert anything into the backlight unit.
(2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.
(3) After the module’s end of life, it is not harmful in case of normal operation and storage.

10.3 STORAGE PRECAUTIONS

When storing modules as spares for a long time, the following precaution is necessary.
(1) Do not leave the module in high temperature, and high humidity for a long time.
It is highly recommended to store the module with temperature from 0 to 35
at normal humidity without
condensation.
(2) The module shall be stored in dark place. Do not store the TFT-LCD module in direct sunlight or fluorescent
light.

30
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

11. REGULATORY STANDARDS

11.1 SAFETY
Regulatory Item Standard
UL UL 60950-1: 2003
Information Technology equipment cUL CAN/CSA C22.2 No.60950-1-03
CB IEC 60950-1:2001
UL UL 60065: 2003
Audio/Video Apparatus cUL CAN/CSA C22.2 No.60065-03
CB IEC 60065:2001

www.jxlcd.com
www.jxlcd.com

31
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval

12. MECHANICAL CHARACTERISTICS



CHI MEI
www.jxlcd.com
www.jxlcd.com

32
Version 2.0
 D IS CONNECT TH E ELECTRIC
P OW ER B EF ORE SERV ICING .
R IS K OF E LE CTRIC SHOCK .
HIGH VOLTAGE
C AU TION

www.jxlcd.com
33

H IG H V OL TAG E
CAUTION
RISK OF E LECTRIC SHOCK . COLD CATHODE FLUORESCENT LAM P IN L CD PANEL CON TAINS A S MAL L A MOU NT OF
DISCONNEC T THE EL ECTRIC M ERCURY P LEASE FOLLOW LOCAL ORDINANCE S OR R EG ULATIONS F OR DISPOSAL.
POW E R B E FOR E SERV ICING .

Issued Date: 23, May 2008

Model No.: V260B1 – L12
CHI MEI


Version 2.0

Approval
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval



CHI MEI
No.

www.jxlcd.com
www.jxlcd.com

34
Version 2.0
 Issued Date: 23, May 2008
Model No.: V260B1 – L12
Approval



CHI MEI
www.jxlcd.com
www.jxlcd.com

35
Version 2.0