www.reinhausen.

com
On-load tap-changer OILTAP® R
Technical Data TD 115
2 TD 115/02 115/02/01/0
 Table of Contents

Table of Contents

1 General .................................................................................................................................................................................................................. 4
1.1 Summary of the technical data ....................................................................................................................................................... 4
1.2 Survey ....................................................................................................................................................................................................... 6

2 Technical Data ................................................................................................................................................................................................... 15

2.1 Rated through-current (Iu), rated step voltage (Ui) and step capacity (PStN) ................................................................ 15
2.2 Contact life ............................................................................................................................................................................................. 17
2.3 Rated withstand voltages of the internal insulation ................................................................................................................ 17

3 Appendix – dimensional and installation drawings .......................................................................................................................... 20

NOTE

These technical data are intended for the calculator and designer of the transformer. These type-specific data are only
valid in connection with the information contained in the general section (TD 61) since this section contains important
information on such subjects as potential connection, leakage inductance, current division, and so on.
Dimensional drawings and connection diagrams are subject to change without prior notice.
Drawings submitted during bidding and ordering are always binding.
Since the on-load tap-changer is delivered to the specifications of the transformer manufacturer, the transformer
manufacturer is responsible for selecting the correct properties of the on-load tap-changer so that the requirements
of the transformer are met.

115/02/01/0
TD 115/02 3
 1 General

1 General

1.1 Summary of the technical data

On-load tap-changer R III 1200 Y R I 1201 R I 2002 R I 24023) R I 3003

Number of poles and application 3 (neutral point) 1 1 1 1

Max. rated through- 1200 1200 2000 2400 3000
current Ium (in A)

Rated short-time withstand 15 15 24 24 30

current (in kA)

Rated short-circuit duration 3 3 3 3 3

(in s)

Rated peak withstand current 37.5 37.5 60 60 75

(in kA)

Max. rated step voltage Uim 4000 4000 4000 4000 3000
(in V)1)

Step capacity (PStN) 3000 30002) 44002) 60003) 6000

(in kVA)

Rated frequency (in Hz) 50 to 60

Operating positions Without change-over selector: max. of 18 With change-over selector: max. of 35

Rated insulation level

Highest voltage for 72.5 123 170 2459) 300 3627)
equipment Um (in kV)5)
Highest operating voltage Ub 55 79 145 170 245 3008)
(phase-phase)
on diverter switch (in kV)
Rated lightning impulse with- 350 550 750 950 1050 1175
stand voltage (in kV, 1.2 I 50)
Rated switching impulse 850 950
withstand voltage (in kV)
AC withstand voltage 140 230 325 395 460 510
(in kV, 50 Hz, 1 min.)
Rated withstand voltages of see table 3
internal insulation

Oil compartment Pressure-proof up to 0.3 bar continuous difference pressure (test pressure 0.6 bar),
head and cover of the on-load tap-changer are vacuum-proof.

Oil suction pipe Installed as standard (for details, see BA 18)

Temperature range The on-load tap-changer OILTAP® R can be operated in the rated load range with oil
temperatures of -25 °C to +105 °C.

Table 1 a

4 TD 115/02 115/02/01/0
 1 General

On-load tap-changer R III 1200 Y R I 1201 R I 2002 R I 2402 R I 3003

Weight without change- 525 360 4454) 445 525

(in kg) ca. over selector

with change- 595 (7704)) 410 (5004)) 505 (6404)) 505 (6404)) 595 (7804))
over selector

Displacement 72.5 kV 289 (3674)) 274 (3534)) 280 (3604)) 280 (3604)) 286 (3674))
volume 123 kV 314 (3924)) 299 (3764)) 305 (3844)) 305 (3844)) 311 (3924))
(in dm3)
ca. 170 kV 334 (4124)) 319 (3964)) 325 (4044)) 325 (4044)) 331 (4124))

245 kV 354 (4324)) 339 (4164)) 345 (4244)) 345 (4244)) 351 (4324))

300 kV 369 (4464)) 374 (4534)) 374 (4534)) 380 (4614))

Oil filling 72.5 kV 168

quantity VS 123 kV 188
and minimum
volume DV6) 170 kV 203
of the diverter
switch oil 245 kV 218
compartment 300 kV 240

Table 1 b

Notes for tables 1a and 1b:

1) The maximum rated step voltage may be exceeded by 10% due to overexcitation of the transformer if the step capacity is
limited to its rated value.
2) Higher step capacities available as special design
3) Forced current division by two parallel winding branches required
4) Applies to tap selector size E
5) In accordance with VDE 0111, part 1: R.m.s. value of the phase-phase voltage for which a piece of equipment is rated for
its insulation
6) Minimum volume of oil conservator for oil temperature ϑ = –30 °C ... +100 °C: DV = 0,1 VS + 4 (dm3)
7) On request
8) Oil filter unit 0F 100 (combi-filter) required, UbST > 300 kV on request
9) Rated withstand voltages comply with IEC 60214: 1989; unrestricted tests possible up to 1050 kV 1.2|50 or 460 kV,
50 Hz, 1 min.

115/02/01/0
TD 115/02 5
 1 General

1.2 Survey

8997470E_01

Fig. 1a Survey of the on-load tap-changer designs (no. of poles, change-over selector, and installation lengths)

6 TD 115/02 115/02/01/0
 1 General

8997470E_02

Fig. 1b Survey of the on-load tap-changer designs (no. of poles, change-over selector, and installation lengths)

115/02/01/0
TD 115/02 7
 1 General

Survey of the basic connection diagrams (figures 2a, 2b, 2c) with designation of the tap selector contact terminals in accord-
ance with MR standards. This contact terminal designation corresponds to the specifications in the on-load tap-changer
dimensional drawings.

Fig. 2a

excerpt from 8906164E_1

8 TD 115/02 115/02/01/0
 1 General

Fig. 2b

8906164D_2

115/02/01/0
TD 115/02 9
 1 General

Fig. 2c

8906164D_3

10 TD 115/02 115/02/01/0
 1 General

Examples of connection diagrams (contact designation in acc. w. MR standards)

Fig. 3 Example: On-load tap-changer R III 1200 Y–C/D, basic connection diagram 10 19 1 W

115/02/01/0
TD 115/02 11
 1 General

Fig. 4 Example: On-load tap-changer R III 1200 Y–E, basic connection diagram 14 27 1 G

12 TD 115/02 115/02/01/0
 1 General

Fig. 5 Example: On-load tap-changer R I 2002–C/D, basic connection diagram 18 35 1 W

115/02/01/0
TD 115/02 13
 1 General

Fig. 6 Example: On-load tap-changer R I 3003–C/D, basic connection diagram 18 35 1 W

14 TD 115/02 115/02/01/0
 2 Technical Data

2 Technical Data

2.1 Rated through-current (Iu), rated step voltage (Ui) and step capacity (PStN)

R I 2003
On-load- R III 1200 Y R I 1201 R I 2002 (Special R I 24021) R I 3003
tap-changer design)

Iu (A) 700 1200 700 1200 1070 2000 1300 2000 1400 2400 2000 3000

Ui (V) 4000 2500 4000 2500 4000 2200 4000 3000 4000 2500 3000 2000

PStN (kVA) 2800 3000 2800 3000 4280 4400 5200 6000 5600 6000 6000 6000

Table 2 Rated through-currents (Iu), related rated step voltages (Ui) and step capacities (PStN),
at highest and lowest rated step voltage of the step capacity curve (see fig. 7 and fig. 8)
1)
Note: R I 2402 with forced current division by two parallel winding branches

Fig. 7
Step capacities (rated step voltages Ui, rated through-
currents Iu) for on-load tap-changer R III 1200 Y,
R I 1201, R I 1202

CAUTION:
Only applies to network service. When used for
8997510E
industrial transformers, please contact us.

115/02/01/0
TD 115/02 15
 2 Technical Data

8997510E

Fig. 8
Step capacities (rated step voltages Ui, rated through-currents Iu) for on-load tap-changer R I 2002,
R I 2003 (= special design), R I 2402, R I 3003.
Note: 1) R I 2402 with forced current division by two parallel winding branches.
CAUTION: Only applies to network service. When used for industrial transformers, please contact us.

16 TD 115/02 115/02/01/0
 2 Technical Data

2.2 Contact life

The mean expected contact life of the arcing diverter switch contacts can be estimated based on the relative load (Iu / Ium)
as shown in figure 9. Since actual contact life in individual cases depends on many influencing factors while in service,
only estimations can be given (not applicable to constant current service).
The inspection regulations must be observed.

KHW 579-4
Fig. 9 Expected mean contact life under average load
n – Number of operations
Iu – Rated through-current
Ium – Max. rated through-current

115/02/01/0
TD 115/02 17
 2 Technical Data

2.3 Rated withstand voltages of the internal insulation

Fig. 10 shows diagrams of the voltage stress present on the tap winding of the three primary basic connections of three-
pole on-load tap-changers and single-pole on-load tap-changers.
When selecting the on-load tap-changer, a check must be made to determine whether the highest stress on the tap selector
does not exceed the related rated withstand voltages.

Without change-over selector With reversing switch

With coarse tap selector in (+) - position With coarse tap selector in (-) - position

CAUTION
Adhere to the maximum rated
8997560M lightning impulse withstand
voltage stress on a0 in mid-position.

a0 = Between preselected and selected tapping on the diverter switch

a1 = Between tap selector contacts of the winding of one tap position (connected or not)
a = Between beginning and end of a tapped winding and, with coarse tap winding, between beginning and end of a coarse tap winding.
Note for coarse tapping arrangement in (-) -position of the change-over selector:
When stressed with impulse voltage, the permissible withstand voltage „a“ must be adhered to between the end of a coarse tap winding connected with
the K tap selector contact and the tap selector contact at the end of the tapped winding of the same phase.
b = Between the tap selector contacts of different phases and between change-over selector contacts of different phases, which are connected with the
beginning/end of a tapped winding or with a tap selector contact.
f = Between diverter switch terminal and ground
Additional for coarse tapping arrangement in (+) - position of the change-over selector:
c1 = From one (-) -change-over selector contact to terminal of the same phase.
c2 = Between (-) -change-over selector contacts of different phases

Fig. 10 Rated withstand voltages

18 TD 115/02 115/02/01/0
 2 Technical Data

Insulation Tap selector size C Tap selector size D1) Tap selector size E
distances kV 1.2I50 kV, 50 Hz, 1 min kV 1.2I50 kV, 50 Hz, 1 min kV 1.2I50 kV, 50 Hz, 1 min

a0 Ub £ 72.5 kV: 140 kV 1.2I50; 30 kV, 50 Hz, 1 min / Ub >72.5 kV: 80 kV 1.2I50; 3 x USt

a1 150 30 150 30 150 30

a 400 85 5002) 110 670 180

b3) 400 100 5002) 150 670 180

c1 550 180 590 210 820 250

c23) 550 195 590 225 820 280

Table 3 Rated withstand voltages (in kV) of the internal insulation of the tap selector

1)
Note: Tap selectors in accordance with basic connection diagrams 10 09 1 W, 12 11 1 W, 14 13 1 W are designed as
18 09 1 W, 18 11 1 W, 18 13 1 W.
Tap selectors in accordance with basic connection diagrams 16 15 1 W and 18 17 1 W are not possible.
2)
Higher values up to 550 kV on request
3)
Omitted for on-load tap-changers R I 1201, R I 2002/2402, R I 3003

The tap selector size (ID letters C, D, E) characterizes the internal insulation of the tap selector whose rated withstand
voltages must be adjusted to the requirements of the transformer winding.
The permissible maximum service voltage along the individual tap selector paths is half the AC withstand voltages listed in
table 3.

115/02/01/0
TD 115/02 19
 3 Appendix

3 Appendix

Dimensional drawings
On-load tap-changer OILTAP® R III 1200 Y, tap selector size C/D, E ...................................................................................... 896722, 897867
On-load tap-changer OILTAP® R I 1201, tap selector size C/D, E ........................................................................................... 899753, 899401
On-load tap-changer OILTAP® R I 2002, tap selector size C/D, E ........................................................................................... 896721, 897866
On-load tap-changer OILTAP® R I 2402, tap selector size C/D, E ........................................................................................... 897490, 897864
On-load tap-changer OILTAP® R I 3003, tap selector size C/D, E ........................................................................................... 896720, 897865
Tap selector and change-over selector terminal contacts, tap selector size E ...................................................................................... 897868

Installation drawings
Tap selector size C/D ................................................................................................................................................................................................ 896705
Tap selector size E ..................................................................................................................................................................................................... 897873

Additional drawings
On-load tap-changer head .................................................................................................................................................................................... 893899
On-load tap-changer cover with mounting flange for pressure relief valve ........................................................................................ 895168
Versions of the on-load tap-changer head, swiveling range of gear unit ............................................................................................. 896703
Special design for installation in bell-type tanks ........................................................................................................................................... 896762
Horizontal drive shaft, tap selector size C/D, E .............................................................................................................................. 896708, 897872
Jumpers for parallel connection of tap selector terminal contacts for on-load tap-changer OILTAP® R I 2002,
R I 3003, selector size C/D, E ................................................................................................................................................................ 896706, 898713
Tap selector bottom, shielding, tap selector size C/D .................................................................................................................................... 896702
Tap selector bottom, tap selector size E ............................................................................................................................................................ 897869
Tie-in resistors, tap selector size C/D .............................................................................................................................. 896707, 898124 - 898135
Potential switch, tap selector size C/D, E ......................................................................................................................................... 898136, 898614
Additional drawings for on-load tap-changer ................................................................................................................................................ 898826

20 TD 115/02 115/02/01/0
 8967227E
On-load tap-changer OILTAP® R
R III 1200 - C/D, dimension drawing

115/02/01/0
TD 115/02 21
 8978677E
On-load tap-changer OILTAP® R
R III 1200 - E, dimension drawing

22 TD 115/02 115/02/01/0
 8997530E
On-load tap-changer OILTAP® R
R I 1201 - C/D, dimension drawing

115/02/01/0
TD 115/02 23
 8994011E
On-load tap-changer OILTAP® R
R I 1201 - E, dimension drawing

24 TD 115/02 115/02/01/0
 8967218E
On-load tap-changer OILTAP® R
R I 2002 - C/D, dimension drawing

115/02/01/0
TD 115/02 25
 8978666E
On-load tap-changer OILTAP® R
R I 2002 - E, dimension drawing

26 TD 115/02 115/02/01/0
 8974905E
On-load tap-changer OILTAP® R
R I 2402 - C/D, with forced current division with two parallel
winding branches, dimension drawing

115/02/01/0
TD 115/02 27
 8978646E
On-load tap-changer OILTAP® R
R I 2402 - E, with forced current division with two parallel
winding branches, dimension drawing

28 TD 115/02 115/02/01/0
 8967208E
On-load tap-changer OILTAP® R
R I 3003 - C/D, dimension drawing

115/02/01/0
TD 115/02 29
 8978657E
On-load tap-changer OILTAP® R
R I 3003 - E, dimension drawing

30 TD 115/02 115/02/01/0
 8978683E
On-load tap-changer OILTAP® R
Tap selector size E,
tap selector and change-over selector terminal contacts

115/02/01/0
TD 115/02 31
 8967056E
On-load tap-changer OILTAP® R
Tap selector size C/D, installation drawing

32 TD 115/02 115/02/01/0
 8978733E
On-load tap-changer OILTAP® R
Tap selector size E, installation drawing

115/02/01/0
TD 115/02 33
 893899AE
On-load tap-changer OILTAP® MS, M, R, RM
On-load tap-changer head, centric drive

34 TD 115/02 115/02/01/0
 8951685E
On-load tap-changer OILTAP® MS, M, R, RM
With flange for pressure relief valve

115/02/01/0
TD 115/02 35
 8967034E
On-load tap-changer OILTAP® R
Versions of the on-load tap-changer head, swiveling range and
drive direction of the gear unit

36 TD 115/02 115/02/01/0
 8967627E
On-load tap-changer OILTAP® MS, M, R, RM
Special design for installation in bell-type tank

Lifting device
O-Ring 44.2 - 5,7

Suction pipe

Drilling hole in sectional plane

Transformer cover

O-Ring

Level traverse

Guiding ring with

Um = 170 kV,
245 kV, 300 kV

Supporting flange

Level traverse

Z = Guiding pin

Drive side of the tap selector

115/02/01/0
TD 115/02 37
 8967087E
On-load tap-changer OILTAP® MS, M, R, RM
Horizontal drive shaft (limit dimensions)
Tap selector size C/D, centric drive

38 TD 115/02 115/02/01/0
 8978723E
On-load tap-changer OILTAP® R
Horizontal drive shaft (limit dimensions)
Tap selector size E, centric drive

115/02/01/0
TD 115/02 39
 8967066E
On-load tap-changer OILTAP® R
R I 2002, R I 3003, tap selector size C/D
Jumpers for parallel connection of tap selector terminal contacts

40 TD 115/02 115/02/01/0
 8987131E
On-load tap-changer OILTAP® R
R I 2002, R I 3003, tap selector size E
Jumpers for parallel connection of tap selector terminal contacts

115/02/01/0
TD 115/02 41
 8967028E
On-load tap-changerOILTAP® R
Tap selector size C/D, tap selector bottom shown with the lowest parts connected to
the voltage, standard design without grading ring, special design with grading ring

42 TD 115/02 115/02/01/0
 8978695E
On-load tap-changer OILTAP® R
Tap selector size E, tap selector bottom shows lowest parts
connected to voltage

115/02/01/0
TD 115/02 43
 8967078E
On-load tap-changer OILTAP® R
Tap selector size C/D, principal arrangement of potential switch and
tie-in resistors

44 TD 115/02 115/02/01/0
 8981242M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R I to WP, tap selector size C/D,
Um = 72.5 kV to 300 kV, 2 x 14 to 2 x 18 resistors

115/02/01/0
TD 115/02 45
 8981252M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R I to WP, tap selector size C/D,
Um = 72.5 kV to 300 kV, 2 x 3, 2 x 5, to 2 x 13 resistors

46 TD 115/02 115/02/01/0
 8981262M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R I to WP, tap selector size C/D,
Um = 72.5 kV to 300 kV, 2 x 4, 2 x 6 to 2 x 12 resistors

115/02/01/0
TD 115/02 47
 8981272M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R I to WP, tap selector size C/D,
Um = 72.5 kV to 300 kV, 3 to 26 resistors

48 TD 115/02 115/02/01/0
 8981282M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R I to WR, tap selector size C/D,
Um = 72.5 kV to 300 kV, 2 x 14 to 2 x 18 resistors

115/02/01/0
TD 115/02 49
 8981292M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R I to WR, tap selector size C/D,
Um = 72.5 kV to 300 kV, 2 x 3, 2 x 5, to 2 x 13 resistors

50 TD 115/02 115/02/01/0
 8981302M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R I to WR, tap selector size C/D,
Um = 72.5 kV to 300 kV, 2 x 4, 2 x 6, to 2 x 12 resistors

115/02/01/0
TD 115/02 51
 8981312M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R I to WR, tap selector size C/D,
Um = 72.5 kV to 300 kV, 3 to 26 resistors

52 TD 115/02 115/02/01/0
 8981322M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R III 1200 WP, tap selector size C/D,
Um = 72.5 kV to 245 kV, 3 x 2 to 3 x 7 resistors

115/02/01/0
TD 115/02 53
 8981332M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R III 1200 WP, tap selector size C/D,
Um = 72.5 kV to 245 kV, 3 x 8 to 3 x 10 resistors

54 TD 115/02 115/02/01/0
 8981342M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R III 1200 WR, tap selector size C/D,
Um = 72.5 kV to 245 kV, 3 x 2 to 3 x 8 resistors

115/02/01/0
TD 115/02 55
 8981352M
On-load tap-changer OILTAP® R
Tie-in resistor cylinder R III 1200 WR, tap selector size C/D,
Um = 72.5 kV to 245 kV, 3 x 9 to 3 x 11 resistors

56 TD 115/02 115/02/01/0
 8981362M
On-load tap-changer OILTAP® R
Potential switch R III 1200 WS, R I to WS, tap selector size C/D,
Um = 72.5 kV to 300 kV

115/02/01/0
TD 115/02 57
 8986142M On-load tap-changer OILTAP® R
Potential switch R III 1200 WS, R I to WS, tap selector size E,
Um = 72.5 kV to 300 kV

58 TD 115/02 115/02/01/0
 8988261E On-load tap-changer OILTAP® R
Additional drawings for on-load tap-changer

Basic connection diagrams .............................................................. 890616

Tap selector and change-over selector terminal contacts,

tap selector size E................................................................................ 897868

Tap selector bottom, shielding,

tap selector size C/D ........................................................................... 896702

Tap selector bottom, tap selector size E ...................................... 897869

Versions of the on-load tap-changer head ................................ 896703

Horizontal drive shaft, tap selector size C/D .............................. 896708

Horizontal drive shaft, tap selector size E ................................... 897872

Installation drawing, tap selector size C/D ................................. 896705

Installation drawing, tap selector size E ...................................... 897873

On-load tap-changer head .............................................................. 893899

115/02/01/0
TD 115/02 59
 © Maschinenfabrik Reinhausen GmbH Phone +49 941 40 90-0
www.reinhausen.com Falkensteinstrasse 8 Fax +49 941 40 90-111
93059 Regensburg, Germany E-Mail [email protected]

Please note: The data in our publications may differ from the data of the devices delivered.
We reserve the right to make changes without notice.
TD 115/02 en • 0903/1000 • 115/02/01/0 • F0019601 • Printed in Germany