Scribd
Upload
139 views1 page

The Supply Must Include The Following Additional Equipments and Add-On Float Cum Boost Charger 48V, 10A Rating 02 No

The document describes the specifications for an EPABX system with 64 lines. It will include 64 analog extensions, 8 junction ports, and additional equipment like chargers, frames, and operator consoles. The system uses a microprocessor-based digital switching technology and modular design to allow expansion. Peripheral cards are hot-swappable and it supports both DTMF and FSK telephone instruments. The system has redundant power supplies and an ISDN digital platform.

Uploaded by

jayant5253
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
139 views1 page

The Supply Must Include The Following Additional Equipments and Add-On Float Cum Boost Charger 48V, 10A Rating 02 No

The document describes the specifications for an EPABX system with 64 lines. It will include 64 analog extensions, 8 junction ports, and additional equipment like chargers, frames, and operator consoles. The system uses a microprocessor-based digital switching technology and modular design to allow expansion. Peripheral cards are hot-swappable and it supports both DTMF and FSK telephone instruments. The system has redundant power supplies and an ISDN digital platform.

Uploaded by

jayant5253
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

EPABX SYSTEM ( 64 LINES)

1. The EPABX shall have 64 analog extensions, 08 junction ports


2. 64 No. of Analogue sets to be replaced.
3. It shall be ISDN compatible.
4. The subscriber feed through voltage from the system must be 48 V DC
5. The supply must include the following additional equipments and add-on
a. FLOAT CUM BOOST CHARGER 48V, 10A RATING 02 NO.
b. Main Distribution Frame - 200 pair 01 no.
c. Hot standby for CPU - 01 no.
d. Hot standby for power unit 01 no.
e. 16 line operator console 03 nos
f. Junction card ( 8 lines per card) 02 no.
g. DIGITAL CARD ( 8 LINES PER CARD) 01 NO.
h. Line extension card 03 nos. 8 lines per card as operational spare

6. The equipment shall be electronic type. It shall have microprocessor / micro controller
based on Stored Program Control Technique. It shall employ PCM/TDM, 100% non-
blocking, digital switching technology.
7. The system should be built on a universal slot architecture and modular in design to
enable seamless growth, by adding the desired necessary cards as and when required.
Any peripheral card can be inserted in any slot of the platform, whereby it is possible to
increase or decrease the trunk lines or subscriber lines of the system as per the
requirement in future as per mentioned maximum requirement.
8. All the peripheral cards (extension cards, trunk cards (ISDN) etc.) should be hot
swappable. i.e. it should be possible to replace a peripheral card while EPABX power is
on.
9. It should be suitable for DTMF as well as the FSK type of telephone instruments.
10. The EPABX systems should have power supply from redundant 48V/20A FCBC
11. The system shall have an ISDN Digital platform .
12. EPABX should have built-in one number of public address port and external music port.
13. The system can be programmed through Analog telephone, Digital key phone,Ethernet
or serial cable without any external devices.
14. System should be configured to make calls between Alcatel PBX over junction.
15. EPABX System should be configured and programmed at installation site.

You might also like