Scribd
Upload
106 views6 pages

Problem 6 Doc Uci

This document summarizes the results of a well test on the Red Reservoir 1. The well was produced at 1000 STBPD for 72 hours while bottomhole pressures were measured. Analysis of the pressure data determined the reservoir permeability to be 15,747 md. The calculated wellbore skin factor was 0.73, resulting in a total pressure drop due to skin of 109.727 psi. The radius of investigation at the end of the test was calculated to be 23.41 feet.

Uploaded by

suci wulandari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
106 views6 pages

Problem 6 Doc Uci

This document summarizes the results of a well test on the Red Reservoir 1. The well was produced at 1000 STBPD for 72 hours while bottomhole pressures were measured. Analysis of the pressure data determined the reservoir permeability to be 15,747 md. The calculated wellbore skin factor was 0.73, resulting in a total pressure drop due to skin of 109.727 psi. The radius of investigation at the end of the test was calculated to be 23.41 feet.

Uploaded by

suci wulandari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

Problem 6-3

Fluid Flow: Well Testing

The Red Reservoir 1 was produced for 72 hours at 1000 STBPD


The bottomhole pressures measured during the test are included in the data spreadsheet
Other important parameters are:

Net pay thickness 25,5 ft


Porosity 0,204
Core permeability 18 md
Oil FVF 1,41 rb/stb
Oil viscosity 0,303 cp
Oil compressibility 1,63E-05 psi-1
Total Compressibility 1,54E-05 psi-1
Wellbore radius 0,35 ft
Wellbore volume 405 bbl

BHP 51
Time 14
Pi 5084
P1hour 4125
T 520
Time Pressure Time Pressure
hours psia hours psia
0.0000 5084.00 8.0787 3967.289
0.0168 4958.625 8.9931 3967.419
0.0355 4851.715 9.9939 3951.714
0.0566 4757.881 11.9960 3934.269
0.0803 4668.398 13.9970 3939.403
0.1070 4580.067 15.9990 3911.184
0.1370 4511.971 18.0000 3910.857
0.1708 4446.42 20.0020 3911.158
0.2088 4400.983 22.0040 3899.695
0.2516 4364.904 24.0050 3886.049
0.2996 4310.857 26.0070 3889.903
0.3537 4277.956 28.0080 3881.385
0.4146 4261.84 30.0100 3871.982
0.4830 4233.172 32.0120 3874.889
0.5600 4213.746 34.0130 3872.317
0.6467 4200.986 36.0150 3852.147
0.7441 4168.272 38.0160 3862.512
0.8538 4167.31 40.0180 3845.501
0.9771 4152.005 44.0210 3846.784
1.1159 4125.855 48.0240 3831.643
2.1171 4088.086 52.0280 3839.216
3.0699 4038.457 56.0310 3826.632
3.9219 4019.968 60.0340 3812.379
4.9995 4012.814 64.0370 3819.018
6.3627 3982.283 68.0400 3818.733
7.1739 3990.206 72.0440 3801.853

4179−3780
 𝑀 = 𝐿𝑂𝐺 0,5−𝐿𝑂𝐺100 = −173 = 173
162,6∗𝑄∗𝐵∗𝜇
 M= 𝐾∗25,5

162,6∗1000∗1,41∗0,3
173 = 𝐾∗25,5

K =15,747

Analyze the drawdown test to determine reservoir permeability and the wellbore
skin factor. What is the total pressure drop due to skin? Is there any justification to
stimulate the well?

𝑃𝑖−𝑝𝑤𝑓 𝑘
 S= 1,151 [ − 𝑙𝑜𝑔10 {∅∗𝜇∗𝐶𝑡∗𝑟𝑤2 } + 3,23]
𝑚
5084−4125 15,747
= 1,151 [ − 𝑙𝑜𝑔10 {0,204∗0,3∗1,54𝐸−0,5∗0,352} + 3,23]
173

= 0,73
 Δpskin = 0,87 * m * s

= 0,87* 173,40061* 0,7273504

= 109,72701

Bonus Questions

What is the radius of investigation at the end of the drawdown?

What drawdown length would be required to investigate the mapped reservoir area
of 1721 acres, assuming the well was in the center of a circular reservoir?

A= πr2
1721 =3,14* r2

r = 23.41

𝑘𝑥𝑡
rinv = 0.0324 √ 𝑥  𝑥 𝐶𝑡

15.7 𝑥 𝑡
23.41 = 0.0324 √0.204 𝑥 0.303 𝑥 1.54𝐸−05

t =
Time of
Pwf, Flow Rate Delta
Test Remarks Delta P
psia MMscf/d P(MMPSI)
(hrs)
14 2000 0 Shut in 0 0
10 1842 4 Flow #1 607036 0,607036
1982 0 Shut in
10 1712 6 Flow #2 1069056 1,069056
10 1960 0 Shut in
10 1511 8 Flow #3 1716879 1,716879
10 1913 0 Shut in
10 1306 10 Flow #4 2294364 2,294364
Extended
26 1072 10 2850816
Flow 2,850816
Final Shut
68 2000 1 0
In 0,137
Buat Grafik Test Flow Extended Flow dan AOF

10

y = 0.137x1.3182
1

0.1
1 Test Flow extended 10 aof Power (extended) 100

Tentukan nilai x dengan range antara 1-10 atau range nilai pada Q

Setelah itu tentukan nilai y dengan menggunakan equation yang muncul pada grafik
saat Display on Chart y = 0,137x1,3182

x 2 5
y 0,341616 1,143149

Setelah itu cari nilai C,N dan AOF

𝐿𝑂𝐺 𝑋2−𝐿𝑂𝐺𝑋1
N= 𝐿𝑂𝐺𝑌2−𝐿𝑂𝐺𝑌1

C
AOF=(𝑃𝑅2 )𝑁

N 0,758610226
C 0,0001268
AOF 12,92959

You might also like