DMYCO 3D PRINTER

DMY3DP-001
INSTALLATION GUIDE V0.1
 Classification Of Screws

M3*20mm screws M2.5*10mm black

M3 nuts 60pcs
58pcs screws 2pcs

M3*10mm screws M3*30mm screws

M8 nuts 12pcs
17pcs 7pcs

M8 Cushion ring M3*14mm screws

Plastic Pillars 4pcs
12pcs 4pcs
 Classification Of Screws

M4*15mm screws
M3*30mm screws 4pcs
12pcs

M3*20mm screws
Wing nuts*4 Compression springs*4 4pcs
Step 1 Assemble Y-axis Motor
 Fit the GT2-16 pulley on the motor, Locking with M3*2mm
jackscrew.

 As the picture, Put Y-axis motor on <Y-axis motor support> ,

locking with Four M3*10mm screws.
GT2-16 pulley

Y-axis motor

M3*2mm jackscrew

Y-axis motor
support
M3*10mm
Round head screws*4
Step 2 Assemble Y-axis Limit switch
 Put the Y-axis limit switch and the holder together ,locking
with two M3*20mm screws & nuts. As picture M3*20mm screws

Y-axis limit switch

Y-axis limit
switch holder
(Acrylic)

M3 nuts
Step 3 Assemble Base Frame Holder_Back
 As the picture, put two of the Sliding rod Sliding rod
Restriction in front of the base frame Restriction*2
holder (back). locking with two M3*20mm
screws & nuts. M3*20mm
screws M3 nuts
 Put the limit switch and holder assembly
on the base frame holder, locking with one
M3*20mm screw & nut.

 Put Y-axis motor holder on base frame

holder ,locking with one M3*20mm screw
& nut.

 Put Y-axis motor assembly on base frame Y-axis limit

holder, locking with three M3*20mm switch assembly
screws & nuts.

Y-axis motor assembly

Y-axis motor
Base frame
holder
holder_Back
Step 4 Assemble Base Frame Holder_Front
 As the picture, put two of the Sliding rod Restriction
in front of the base frame holder _front. locking with
two M3*20mm Round head screws & nuts.
Base Frame
 Put Y-axis belt pulley wheel assembly behind the Holder_Front
base frame holder, Locking with two M3*20mm Y-axis belt pulley
screws & nuts. wheel assembly

M3*20mm Round
head Screws & nuts

Sliding rod
Restriction*2
 Step 5 Assemble Extruder (with Auto leveling)
Bearing
 Install Cooler Fan on the Metal Block use 2pcs
U-Metal plate M3*16mm cross screws .
 Put Fan and Position Sensor Holder to the U-Metal
Motor & Hotend plate, and locking with 2pcs M3*20mm and 1pcs
Metal Block M3*10mm Cross screws ,as picture
 Put the Position Sensor on the holder ,locking with
2pcs M3*22mm cross screws.

Cooler Fan
Fan

M3*16mm cross screws

cross screws M3*22mm

M3*22mm
cross screws
Position Sensor
Step 6 Assemble Z-axis motor
coupling
 Put two Z-axis motor support(side) in two
sides of the motor, Cover the Z-axis motor
Z-axis motor
support(top) on the top, locking with
support(top)
M3*20mm screws & nuts.

 The cable of Z-axis motor is back of the Z-axis

motor support. Locking Z-axis motor with
four M3*10mm screws. M3*20mm screws

 Put the coupling on the motor, locking with M3*10mm screws

the jackscrews.
Z-axis motor
 Another Z-axis motor is the same assembly. support(side)

Note: There are 2pcs Z axis motors . See the

hole , the right motor put the hole on the
right , the left motor put the hole on the Z-axis motor
left . (The picture shows the right motor )
 Step 7 Assemble Z-axis
 As the picture, Put the two Z-axis motors assembly
on the left and right side of the Bottom plate,
locking with three M3*20mm screws & nuts.

M3*20mm
screws

Z-axis motor assembly

The hole is on the left Bottom plate

M3 nuts
The hole is on the right
Step 8 Assemble Side plate
 As the picture, Put the two Side plate on the
left and right side of the Bottom plate ,
locking with four M3*20mm screws & nuts.

Side plate

M3*20mm
screws
Step 9 Assemble Top plate & Junction Plate
Sliding rod
 As the picture, Put the Top plate on Side restriction
Plate, locking with four M3*20mm screws &
nuts. Junction Plate
 Put the two Junction Plate on the top of the
Side plate ,locking with four M3*20 screws &
nuts.
 Put two sliding rod restriction on the top of Top plate
left and right sides. Locking with one
M3*20mm screw & nut each.
M3*20mm
screws
Step 10 Install LCD display LCD display
 Put the LCD display on the top of the assembly
Top plate ,locking with three
M3*25mm screws &nuts M3 nuts

M3*25mm Framework
screws (top half)
Step 11 Install Power supply
 Put Power supply on the right of the side
plate , locking with three M3*14mm screws
and nuts.

Side plate

Power supply

M3*14mm
screw
Step 12 Install PCBA Control Board
 Install Control Board as picture , locking with
Four M3*30mm screws + 4pcs Plastic pillars +
4pcs M3 nuts

Plastic Pillars*4

M3 Nuts*8 M3*30mm
Screws *4

Side plate
Control Board
Step 13 Install Base frame holder_Back
 Put the Base frame holder_back back of Side plate,
locking with four M3*20mm screw

M3*16mm
screws*4
Base frame
holder_back
Step 14 Install Base Frame Holder_Front
 Through the Frame Holder_Front & Back by two
M8*400mm screw arbors, locking with twelve
M8 Nuts & cushion ring.

M8 nuts

M8 cushion ring

M8*400mm Base frame

screw arbors holder_front
Step 15 Assemble Bed frame
 Place three bearings under the bed frame,
locking with twelve M4*15 screws. Bearing*3

M4*15mm
screws *12
Step 16 Assemble Bed frame
 Place three bearings under the bed frame, locking with
twelve M4*15 screws.
 Through the bed frame on the base by two of M8*380mm
Sliding rod. Fix both end by Sliding rod restriction
 Tighten one end of the timing belt to the bed frame using a
zip-ties. the other end through the Y-axis motor and belt
pulley wheel on the base frame holder , Then tighten it to
the bed frame using zip-ties as shown in the picture .

M8*380mm
sliding rod*2
Sliding rod
Nylon cable ties Restriction Timing belt
Step 17 Assemble Heatbed
 Place the MK3 heatbed on the bed frame use
4pcs springs between them, and then through
4pcs M3-30mm screws, top 4pcs wing nuts under
the bed frame.

MK3 Heatbed

Springs*4

M3*30mm
screws *4
Wing nut*4
Step 18 Assemble X-axis
 Through the X-axis motor mount & Extruder
Pulley mount and Extruder assembly assembly
using two M8*443mm sliding rods, as the
picture.
 Put X-axis limit switch on the X-axis
motor mount, locking with two M8*443mm
M2.5*10mm screws (small black screw) sliding rod

X-axis motor
mount

X-axis limit
switch

X-axis pulley
mount
Step 19 Instal X-axis Timing Belt
 Tighten one end of the Timing Belt to the
Belt clip with Nylon cable ties. The other end X-axis timing belt
through the X-axis pulley & motor , then
tighten another end of the belt to the
another Belt clip with Nylon cable ties . as
picture below Nylon cable ties

Belt clip
Step 20 Control Board Wiring Diagram
 The method of connecting wire is as picture
!NOTE!: The wires connected to POWER SUPPLY and
HETBED must be AWG14 or thicker one.

PS: For auto level 3D printer, there only 2pcs limit switches ,
one for X-axis and one for Y-axis, the Position sensor is for
Z stop and auto leveling .
Step 21 AC Power Connector Wiring Diagram
 Connect Power cable as the picture (Right)

Note: There are different voltages in different country.

Please select the appropriate voltage by switch before
power on. As the picture below.
 Step 22 Assemble Filament Feeder
 Separately put two Plastic Pipe holder on
two Filament support frame, locking with
Plastic Pipe four M3*20mm head screws & nuts.

 Connect the two Filament support frames

with two Fixed links , locking with four
M3*20mm screws & nuts
Filament spool

Plastic Pipe
holder M3 nuts

Filament
support frame

M3*20mm screws

Fixed Link
Installation Finished