Boost 1channel White Led Driver For Large LCDS: Datasheet

Datasheet
Boost 1channel white LED driver

For large LCDs
BD9488F
●General Description ●Key Specifications

BD9488F is a high efficiency driver for white LEDs and  Input voltage range: 9.0V to 18.0V
designed for large LCDs. This IC is built-in a boost  DCDC oscillation frequency: 150kHz (RT=100kΩ)
DCDC converters that employ an array of LEDs as the  Active current consumption: 1.2mA(Typ.)
light source. BD9488F has some protect function against  Operating temperature range: -40℃ to +85℃
fault conditions, such as the over-voltage protection
(OVP), the over current limit protection of DCDC (OCP), ●Package(s) W(Typ.) x D(Typ.) x H(Max.)
LED over current protection (LEDOCP), the open SOP18 11.20mm x 7.80mm x 2.01mm
detection of LED string. Therefore BD9488F is available Pin pitch 1.27mm
for the fail-safe design over a wide range output voltage.
●Features
 Current mode DCDC converter
 Vout discharge circuit as shutdown
 LED protection circuit (OPEN protection, LED OCP
protection)
 LED protect detection as small PWM dimming signal
 Over-voltage protection (OVP) for the output voltage.
 Adjustable soft start time constant
 The wide range of analog dimming 0.2V-3.5V
 The built-in transformation circuit from pulse to DC
 2 PWM dimming signal
 The UVLO detection for the input voltage of the power Figure 1. SOP18
stage
 FAIL logic output
●Applications
 TV, PC display and other LCD backlight system.
●Typical Application Circuit(s) VCC VIN
VCC UVLO
OVP
TC54
STB
GATE
RT
Css CS
SS
FAILB
DIMOUT
PWM1
PWM2
ISENSE
ADIM_P
FB
ADIM
GND
Figure 2. Typical application circuit
○Product structure：Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays
.www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved. TSZ02201-0F1F0C100040-1-2
1/38
TSZ22111・14・001 27.May 2014 Rev.003
BD9488F Datasheet
●Absolute Maximum Ratings (Ta=25℃)

Parameter Symbol Ratings Unit
Input voltage Vccmax 20 V
STB pin voltage STB VCC V
OVP, UVLO, SS, RT,
OVP, UVLO, SS, RT,
ISENSE, FB, CS, TC54 7 V
ISENSE, FB, CS, TC54
pin voltage
PWM1, PWM2, FAILB, PWM1, PWM2, FAILB,
20 V
ADIM, ADIM_P pin voltage ADIM, ADIM_P
DIMOUT, GATE pin voltage DIMOUT, GATE VCC V
Power Dissipation Pd 687 (*1) mW
Operating Temperature Range Topr -40 to +85 ℃
Junction Temperature Tjmax 150 ℃
Storage Temperature Range Tstg -55 to +150 ℃
*1 Pd derated at 5.5 mW/℃ for temperature above Ta=25℃,
mounted on 70mm×70mm×1.6mm 1 layer glass-epoxy PCB.
●Operation range
Parameter Symbol Range Unit
VCC Power source voltage VCC 9.0 to 18.0 V
DC/DC oscillation frequency fsw 50 to 800 kHz
The effective range of ADIM signal VADIM 0.2 to 3.5 V
PWM input frequency range FPWM 90 to 100k Hz
●Pin Configuration ●Package dimension, marking diagram
OVP 1 18 TC54
UVLO 2 17 CS
BD9488F
SS 3 16 FB
RT 4 15 ISENSE
PWM1 5 14 VCC
PWM2 6 13 STB Lot No.
FAILB 7 12 GATE
ADIM 8 11 DIMOUT
ADIM_P 9 10 GND
Figure 3-1. Pin configuration Figure 3-2. Package dimension
www.rohm.com
2/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●1.1 Electrical character (Unless otherwise specified Ta=25℃，VCC=12V)

Limit
Parameter Symbol Min. Typ. Max. Unit Condition
【Total current consumption】
Circuit current Icc － 1.2 1.8 mA VSTB=3V, PWM1=PWM2=0V
Standby current IST － 0 3 μA VSTB=0V
【UVLO block】
Operation voltage（VCC） VUVLO_VCC 6.5 7.5 8.5 V VCC=SWEEP UP
Hysteresis Voltage（VCC） VUHYS_VCC 150 300 600 mV VCC=SWEEP DOWN
UVLO release voltage VUVLO 2.88 3.00 3.12 V VUVLO=SWEEP UP
UVLO hysteresis voltage VUHYS 250 300 350 mV VUVLO=SWEEP DOWN
UVLO pin leak current UVLO_LK -2 0 2 μA VUVLO=4V
【DC/DC block】
ISENSE threshold voltage 1 VLED1 1.47 1.50 1.53 V VADIM=1.5V
ISENSE threshold voltage 2 VLED2 3.33 3.50 3.67 V VADIM=5.0V (as mask analog dimming)
ISENSE threshold voltage 3 VLED3 -2 - +2 % VADIM=0.7V
Oscillation frequency FCT 142.5 150 157. 5 KHz RT=100kohm
GATE pin MAX DUTY
output NMAX_DUTY 90 95 99 % RT=100kohm
GATE pin ON resistance
(as source) RONSO 3.0 6.0 12.0 Ω ION=-10mA
GATE pin ON resistance
(as sink) RONSI 1.2 2.5 5.0 Ω ION=10mA
RT pin voltage VRT 1.0 1.5 2.0 V RT=100kohm
SS pin source current ISSSO -4.20 -3.0 -2.14 μA VSS=2V
SS pin Low output voltage VSS_L - 0.20 0.50 V VSTB=0V, Ioss=50uA
Soft start ended voltage VSS_END 2.7 3.0 3.3 V SS=SWEEP UP
VISENSE=0.2V, VADIM=1.0V,
FB source current IFBSO -140 -100 -60 μA VFB=1.0V
VISENSE=2.0V, VADIM=1.0V,
FB sink current IFBSI 60 100 140 μA VFB=1.0V
OCP detect voltage VCS 360 400 440 mV CS=SWEEP UP
【DC/DC protection block】
OVP detect voltage VOVP 2.88 3.00 3.12 V VOVP SWEEP UP
OVP detect hysteresis VOVP_HYS 50 100 150 mV VOVP SWEEP DOWN
OVP pin leak current OVP_LK -2 0 2 μA VOVP=4V
www.rohm.com
3/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●1.2 Electrical character (Unless otherwise specified Ta=25℃，VCC=12V)

Limit
Parameter Symbol Min. Typ. Max. Unit Condition
【LED protection block】
LED OCP detect voltage VLEDOCP 3.8 4.0 4.2 V VISENSE=SWEEP UP
LED OPEN detect voltage VOPEN 0.05 0.10 0.15 V VISENSE=SWEEP DOWN
【Analog dimming block】
ADIM_P pin HIGH
voltage ADIM_PH 2.0 - 3.8 V
ADIM_P pin LOW voltage ADIM_PL -0.3 - 0.8 V
ADIM_P pin input mask
voltage ADIM_PPU 4.2 - 18 V
ADIM_P pin pull-down
resistance RADIM_P 130 200 300 kΩ VADIM_P=3.0V
ADIM pin output voltage
H ADIMH 3.201 3.30 3.399 V ADIM_P=3.3V
ADIM pin output voltage L ADIML - 0.0 0.05 V ADIM_P=0.0V
ADIM pin output
resistance ADIMR 6.6 10 15 kΩ
ADIM pin leak current ILADIM -2 0 2 μA VADIM=4V, ADIM_P=5.0V
ISENSE pin leak current IL_ISENSE -2 0 2 μA VISENSE=4V
【Dimming signal output block】
DIMOUT source
on-resistance RONSO 6.0 12.0 24.0 Ω ION=-10mA
DIMOUT sink
on-resistance RONSI 1.7 3.5 7.0 Ω ION=10mA
【TC54 block】
TC54 output voltage VTC54 5.2 5.4 5.6 V IO=0mA
TC54 available current |ITC54| 100 - - μA
TC54_UVLO detect
voltage TC54_TH 2.232 2.4 2.568 V VSTB=H, TC54=SWEEP DOWN
TC54_UVLO hysteresis TC54_HYS 50 100 200 mV VSTB=H->L, TC54=SWEEP UP
TC54 discharge current TC54_DIS 5 10 15 μA VSTB=H->L, TC54=4V
【STB block】
STB pin HIGH voltage STBH 2.2 - 19 V VSTB=SWEEP UP
STB pin LOW voltage STBL -0.3 - 0.8 V VSTB=SWEEP DOWN
STB pin input current ISTB 2.0 3.0 4.5 μA VSTB=3.0V
【PWM block】
PWMｘ pin HIGH Voltage PWM_H 2.0 - 18 V VPWMｘ=SWEEP UP
PWMｘ pin LOW Voltage PWM_L -0.3 - 0.8 V VPWMｘ=SWEEP DOWN
PWMｘ pin Pull Down
resistance RPWM 130 200 300 kΩ VPWMｘ=3.0V
【FAIL block (OPEN DRAIN)】
FAILB pin on-resistance RFAIL 0.75 1.5 3.0 kΩ VFAIL=1.0V
FAILB pin leak current ILFAIL -2 0 2 μA VFAIL=15V
www.rohm.com
4/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●1.3 Pin number, pin name, pin function

No. name IN/OUT function rating[V]
1 OVP In Over voltage protection detection pin -0.3 to 7
2 UVLO In Under voltage lock out detection pin -0.3 to 7
3 SS Out Slow start setting pin -0.3 to 7
4 RT Out For DC/DC switching frequency setting pin -0.3 to 7
5 PWM1 In External PWM dimming signal input pin1 -0.3 to 20
6 PWM2 In External PWM dimming signal input pin2 -0.3 to 20
7 FAILB Out Abnormality detection output pin -0.3 to 20
8 ADIM In/Out ADIM signal input-output pin -0.3 to 20
9 ADIM_P In ADIM pulse signal input pin -0.3 to 20
10 GND - -
11 DIMOUT Out Dimming signal pin for driving MOSFET -0.3 to VCC
12 GATE Out DC/DC switching output pin -0.3 to VCC
13 STB In IC On/OFF pin -0.3 to VCC
14 VCC - Power supply pin -0.3 to 20
15 ISENSE In Current detection input pin -0.3 to 7
16 FB In/Out Error amplifier output pin -0.3 to 7
DC/DC output current detect pin,
17 CS In OCP input pin
-0.3 to 7
18 TC54 Out 5.4V output pin, shutdown timer pin -0.3 to 7
www.rohm.com
5/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●2.1.1 Pin ESD Type

OVP UVLO SS
Internal Internal
vol. vol.
OVP SS
50k
5V
RT PWM1, PWM2 FAILB
ADIM ADIM_P DIMOUT
GATE STB ISENSE
Internal
vol.
ISENSE
10k
5V
Figure 4-1. Internal equivalent circuit
www.rohm.com
6/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●2.1.2 Pin ESD Type

FB CS TC54
Internal
Internal vol.
vol.
1k
TC54
FB
Figure 4-2. Internal equivalent circuit
●2.2 Block diagram

VCC VIN
VCC UVLO
OVP
TC54
VREG VCC
UVLO TSD OVP
UVLO
STB
REG54
UVLO
VCC
PWM
RT COMP GATE
OSC
+
- CONTROL
- LOGIC
CS
LEB
Current
sense
Css
SS
SS VCC
DIMOUT
SS-FB
clamper
OPEN LEDOCP
FAILB
Fail
ISENSE
detect
-
+
3.5V
+
ERROR
amp
PWM1 FB
PWM2
+
4.0V
- 3.3V
ADIM_P
+
1.5V
-
10kΩ
ADIM
GND
Package:SOP18
Figure 5. Block diagram
www.rohm.com
7/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●2.3 Typical performance Curves
2.0 10000
1.5 1000
frequency [kHz]
ICC[mA]
1.0 100
0.5 10
0.0 1
7 9 11 13 15 17 10 100 1000
VCC[V] RT[kΩ]
Figure 6. Operating current (ICC) vs VCC Figure 7. GATE frequency vs RT
120 0
100 -20
FB source current[uA]
FB sink current [uA]
80 -40
60 -60
40 -80
20 -100
0
-120
0.5 1.5 2.5 3.5 4.5
0.5 1.5 2.5 3.5 4.5
FB[V]
FB[V]
Figure 8. FB sink current vs FB voltage Figure 9. FB source current vs FB voltage
4.0
ISENSE feedback voltage [V]
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0 2 4 6
ADIM[V]
Figure 10. ISENSE feedback voltage vs ADIM
www.rohm.com
8/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●2.4 Pin function description
○Pin1: OVP
The OVP terminal is the input for over-voltage protection of output voltage. As OVP is more than 3.0V, the over-voltage
protection (OVP) will work. At the moment of this detection, the BD9488 stops the switching of the output GATE and starts
to count up the abnormal interval, but IC doesn't reach latch off state instantaneously until the detection continues up to
the number of counts of GATE terminals, which depend on the kind of abnormality. (Please refer to the time chart in the
section 3.5.7)
The OVP pin is high impedance, because the internal resistance to a certain bias is not connected.
So, the bias by the external components is required, even if OVP function is not used, because the open connection of
this pin is not fixed the potential.
The setting examples is separately described in the section 3.4.6, ”external components selection, how to set OVP”
○Pin2: UVLO
Under voltage lock out pin for the input voltage of the power stage. More than 3.0V(typ.), IC starts the boost operation and
stops lower than 2.7V(typ.).
The UVLO pin is high impedance, because the internal resistance to a certain bias is not connected.
So, the bias by the external components is required, even if UVLO function is not used, because the open connection of
The setting examples is separately described in the section 3.4.5, ”external components selection, how to set UVLO”
○Pin3: SS
The pin which sets soft start interval of DC/DC converter. It performs the constant current charge of 3.0 μA to external
capacitance Css(OPEN to 4.7μF). The switching duty of GATE output will be limited during 0V to 3.0V of the SS voltage.
So the equality of the soft start interval can be expressed as following
6
Tss = 1.0*10 *Css Css: the external capacitance of the SS pin.
Regarding of the logic of SS=L
(SS=L) = (PWM1andPWM2 have not asserted H since ResetB=L->H) or (latch off state)
where ResetB = (STB=H) and (VCCUVLO=H) and (UVLO=H) and (TC54UVLO=H)
As the capacitor of SS pin is smaller than about 1nF, it is necessary to notice if the inrush current I(Vin) as turning-on is
too large, and if the masking interval of OPEN detection is too short.
Please refer to the time chart on soft start behavior in the section 3.7.4
○Pin4: RT
DC/DC switching frequency setting pin. RT set the oscillation frequency inside IC.
○The relationship between the frequency and RT resistance value (ideal)
15000
R RT  [ k ]
f SW [ kHz ]
The oscillation setting range from 50kHz to 800kHz.
The setting examples is separately described in the section 3.4.4, ”external components selection, how to set DCDC
oscillation frequency”
○Pin5, Pin6: PWM1, PWM2

The ON / OFF terminal of the LED driver. LED lights when both PWM signal are high (DIMOUT = H). The Duty signal of
this pin can control the PWM dimming.
The high / low level of PWM pins are following.
State PWM input voltage

PWM1=H or PWM2=H PWM=2.0V to 18.0V
PWM1=L or PWM2=L PWM=‐0.3V to 0.8V
PWM1 and PWM2 have the functional difference, and GATE pin outputs only by the logic of PWM1.
This is why only boost operation continues while PWM1=H, PWM2=L. In this case, the adequate confirmation is required
not to be over voltage of the output voltage Vout.
www.rohm.com
9/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
Figure 11. PWM pin function
○Pin7: FAILB
FAIL signal output pin (open drain). As abnormal, the internal NMOS turn on.
Status FAILB output

Normal OPEN
Abnormal GND Level
○Pin8: ADIM
ADIM_P input level ADIM_P pin function ADIM pin function Required signal to IC
Pulse signal input for DC output signal for DUTY signal for analog
-0.3V<ADIM_P<3.8V analog dimming analog dimming dimming
ADIM_P pin function is DC input signal for DC signal for analog
4.2V <ADIM_P<18V masked. analog dimming dimming
0.8V/2.0V 3.3V
Analog dimming 3.3V
pulse signal
ADIM_P
200k R1=10kohm
Analog dimming
DC signal
C1 0.2V
ADIM DUTY of
ADIM_P [%]
LED current ISENSE
signal 0% 6% 100%
Figure 12. Analog dimming function and character
Above functions enable BD9488 use both of the duty and DC signal for analog dimming.
○When the duty signal is used, that input to the pin ADIM_P with the amplitude about BD9488
3.3V. The input duty of ADIM_P needs to be larger than 6% so that the output ADIM is ADIM
ADIM_P
larger than 0.2V. In the case of the normal feedback with analog dimming, The ADIM pin PULSE
ADIM
voltage is equal to the ISENSE pin voltage. Therefore, please be careful that the lower
ADIM
ADIM voltage than 0.1V causes the OPEN abnormal detection. DC
BD9488
○When the DC signal is used, ADIM_P will be pulled up more than 4.2V, and the signal
input to the pin ADIM. ADIM_P
In the driver module with more than two BD9488, and the analog dimming is performed by ADIM
the duty signal, the architecture will be shown in the right figure. That can reduce the LED
current error between the channels, because the common circuit of the pulse DC
transform is used.
The pulse DC transform circuit outputs DC signal to the ADIM pin with the time constant Figure 13. the analog dimming
of R1, C1 in the above diagram. More C1 value, the ripple components of the ADIM pin circuit as two BD9488 are used.
is decreased, on the other hand, the transient response is delayed.
And please keep in mind the error voltage if the pull down resistor of ADIM pin will be
connected.
○Pin9: ADIM_P
The pulse signal input pin for analog dimming. Please pull up the voltage level more than 4.2V(typ.), when DC signal is
www.rohm.com
10/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
used for the analog dimming. In normal operation, please set the input voltage under 18.0V. For more details, please refer
to <ADIM> pin descriptions.
The input frequency of this pin assumed from 2kHz to 100kHz. Please keep in mind that the capacitor of ADIM pin is
small considering of this input frequency, the error of LED current can be cause.
○Pin10: GND
GND pin of IC.
○Pin11: DIMOUT
This is the output pin for external NMOS of dimming. The below table shows the rough output logic of each operation
state, and the output H level is VCC. Please refer to the time chart in the section 3.7 for detail explanations, because The
DIMOUT logic has the exceptional behavior. Please insert the resistance between the dimming MOS gate to improve the
over shoot of LED current, as PWM turns from low to high.
Status DIMOUT output

Normal PWM1 and PWM2
Abnormal GND Level
○Pin12: GATE
This is the output terminal for driving the gate of the boost MOSFET. The high level is VCC of IC. Frequency can be set
by the resistor connected to RT. Please refer to the <RT> pin description for the frequency setting.
○Pin13: STB
ON/OFF setting terminal for IC, which can be used to perform a reset at shutdown. Please reset this pin after latch off.
Regarding of the sequence of turning on, if the input logic STB turns from low to high, the internal power supply is
activated. After the positive edge of PWM is input , BD9488 starts the boost operation.
○ The input voltage of STB pin toggles the IC state(IC ON/OFF). Please avoid the use of the intermediate level (from
0.8V to 2.2V).
Regarding of the power down sequence, while STB=L and TC54UVLO=H, in order to discharge the output voltage,
DIMOUT logic can assert high, depending on the PWM logic. This discharge behavior is separately described in the time
chart in the section 3.7.3, or in the section 3.4.2, ”how to shutdown and set TC54 capacitance”
○Pin14: VCC
Power supply pin of IC. Input range is from 9V to 18.0V.
The operation starts more than 7.5 V(TYP.) and shuts down less than 7.2 V(TYP.).
○Pin15: ISENSE
This is the input terminal for the current detection. The error amplifier
Vout
compares the lower voltage the analog dimming pin ADIM and 3.5V. The
abnormal voltage of this pin activates the protection function of LED, such as
LEDOCP, OPEN.
[LED OCP Protection Function]

DIMOUT
More than ISENSE = 4.0V (typ.), the over current of LED (LEDOCP) will be
detected. If that states continues 130k clock of GATE pin, IC will latch off.
(Please refer to the time chart in the section 3.7.7.) Error AMP
- ISENSE
[LED OPEN Protection Function] +
If OPEN state (ISENSE<0.1V) continues during 4 clocks interval of GATE + 3.5V ADIM
terminal, BD9488 starts to count the interval of the abnormal state. If the
abnormal condition continues by the completion of counting, BD9488 will be
FB
latched off. (Please refer to the time chart in the section 3.7.6.)
Exceptionally the OPEN protect detection are masked in the following
conditions,
CASE1. When PWM = L. ISENSE is less than 0.1V even in normally,
because DIMOUT = L. Figure 14. ISENSE pin circuit
CASE2. In the soft-start interval. ISENSE is less than 0.1V, because of the
insufficient output voltage Vout.
○Pin16: FB
This is the output terminal of error amplifier. Monitoring the ISENSE terminal voltage, this pin outputs the error signal with
the analog dimming signal (pin ADIM) or 3.5V.
After the completion of the SS, this pin outputs high impedance as the logic “PWM1 and PWM2” asserts low. FB voltage
is hold to the external capacitance.
(For more detail on the compensation setting is described in the section " 3.6 loop compensation".)
www.rohm.com
11/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
○Pin17: CS VIN
The CS pin has two functions.
1. DC / DC current mode Feedback terminal 9488
The inductor current is converted to the CS pin voltage by the sense resistor RCS
and this CS pin voltage controls the output voltage by compared with the error
amp output.
2. Inductor current limit (OCP) terminal GATE Id
The CS terminal also has a over current protection (OCP), if it voltage is more
than 0.4V, the switching operation will be stopped compulsorily. CS
Both of above functions are enable after 300ns (typ.) when GATE pin asserts
high, because the leading Edge Blanking function is included into this IC to Cs Rcs
prevent the affect noise. Please refer to the section 3.5.1 “DCDC parts selection GND
/ how to set OCP”, for detail explanation.
If the capacitance Cs in the right figure is increased to a micro orders, please be Figure 15. CS pin circuit
careful that the limited value of NMOS drain current Id is much than the simple
calculation. Because the current Id flow not only Rcs but also Cs, as the CS pin voltage move according to Id.
○Pin18: TC54
This is the 5.4V (TYP.) output pin that is used for internal power supply. Available current is 100uA.
TC54 can be used as a timer for the discharge of output capacitance DCDC. For detailed instructions, please refer the
section 3.4.2 “how to shutdown and set TC54 capacitance”
www.rohm.com
12/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●3.1 Application circuit example

The bellows are example circuits of using BD9488F.
・The basic application circuit example
VCC VIN
VCC UVLO
OVP
TC54
STB
GATE
RT
Css CS
SS
FAILB
DIMOUT
PWM1
PWM2
ISENSE
ADIM_P
FB
ADIM
GND
Figure 16. The basic application circuit example
・As for the dimming signal, the single PWM and the DC for analog dimming
VCC VIN
VCC UVLO
OVP
TC54
STB
GATE
RT
Css CS
SS
FAILB
DIMOUT
PWM PWM1
PWM2
ISENSE
ADIM_P
FB
Adim (DC) ADIM
GND
PWM1 pin and PWM2 pin are shorted.
Figure 17. the circuit example with single PWM (1) Figure 18. the circuit example with single PWM (2)
www.rohm.com
13/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
・Only analog dimming

VCC VIN
VCC UVLO
OVP
TC54
STB
GATE
RT
Css CS
SS
FAILB
DIMOUT
PWM1
PWM2
ISENSE
ADIM_P
FB
Adim (DC) ADIM
GND
Figure 19. the circuit example of analog dimming only
・Application example when use numerous IC

The application circuit of analog dimming by external duty signal.
Figure 20. the circuit example of when plural IC is used.
www.rohm.com
14/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●3.2 The detection condition list of the protection (TYP. Condition)

Detect condition
Detection Release Timer
Protection pin PWM1 and operation
Protection type
pin condition SS condition
PWM2
ISENSE >
LED OPEN ISENSE ISENSE < 0.1V H(4count) SS>3.0V 130k count Latch off
0.1V
ISENSE <
LED OCP ISENSE ISENSE > 4.0V - - 130k count Latch off
4.0V
UVLO UVLO UVLO<2.7V - - UVLO>3.0V NO Auto recovery
TC54 UVLO TC54 TC54<2.4V - - TC54>2.5V NO Auto recovery
VCC UVLO VCC VCC<7.2V - - VCC>7.5V NO Auto recovery
OVP OVP OVP>3.0V - - OVP<2.9V 4 count Latch off
OCP CS CS>0.4V - - - NO Pulse by Pulse
To reset the latch type protection, please input of STB logic to ‘L’ once. Otherwise the detection of VCCUVLO, TC54UVLO is
required.
The count number in the table suggests the oscillation frequency of DCDC converter.
●3.3 The behavior list of the protection

The operation of the protection
Protect Function DC/DC Gate Dimming transistor
Soft Start FAILB pin
output (DIMOUT) logic
LED OPEN Stops after latch L after latch discharge after latch L after latch
LED OCP Stops immediately H immediately, L after latch discharge after latch L after latch
STB Stops immediately L if TC54<2.4V discharge immediately OPEN
UVLO Stops immediately immediately L discharge immediately immediately L
TC54 UVLO Stops immediately immediately L discharge immediately immediately L
VCC UVLO Stops immediately immediately L discharge immediately immediately L
OVP Stops immediately immediately L discharge after latch L after latch
OCP Stops immediately Normal operation Not discharge OPEN
Please refer to the timing chart in the section 3.7 for the detail.
www.rohm.com
15/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●3.4 External components selection

●3.4.1 The start up operation and the setting of Soft Start external capacitance
The below explanations are the start up sequency of BD9488.
①
5V VOUT
SS
3uA
SS
STB SLOPE
SLOPE
Q D
PWM
FB SS COMP
GATE
OSC Css DRIVER
SS=FB OSC
Circuit
ILED
PWM
LED_OK
DIMOUT
GATE ② FB
PWM=L :STOP
ISENSE
VOUT
③ PWM
ILED
LED_OK ④
⑥
⑤
Figure 21. the turn-on waveform Figure 22. the turn-on circuit
○The explanation of start up sequency

①When STB is H, the internal bias voltage of TC54 rising.
②With the first PWM=H, BD9488 enables output the boost pulse, and the SS start to charge to the external capacitance.
At this moment, the voltage of FB will be the same as SS voltage internally regardless of the PWM logic.
③The FB=SS voltage reach the bottom voltage of saw-toothed wave and the DC/DC start to output the pulse signal.
Therefore the boost of VOUT is started.
④VOUT is boosted to fixed level, and the LED current is rising.
⑤When the LED current reached to fixed level, FB is removed from SS internally. The start up operation completed.
⑥IC start the normal operation by sensing the voltage of ISENSE pin. When SS is more than 3.0V, even if the LED
current does not flows, the clamped circuit of SS and FB is off, and the protect detection of OPEN starts.
○The setting method of SS external capacitance

As above desribed, DC/DC stops when the PWM1=L. It means the boost operation only enabled within PWM1=H
duration and SS time will be extented while boost with samll PWM duty. Also the SS time is affected by the output
capacitance, the LED current and application conditions.
Tss is defined as the time for the SS voltage to reach to the FB feedback voltage. Please set the Tss longer than
Trise_min, which is the start up time of the minimum PWM duty.
When the FB voltage during LED turns on is expressed VFB, the equality on Tss is the following.
Css [ F ]  VFB[V ]
Tss  [Sec]
3[A]
So please set the external capacitance to meet the Tss>>Trise_min.
www.rohm.com
16/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●3.4.2 how to shutdown and set TC54 capacitance

This IC is equipped the discharge function when shutdown is operated.
Figure 23. the shutdown waveform and circuit
○Explanation of shutdown sequence

①When STB=L, DC/DC and TC54 are stop.
②When STB=L, TC54UVLO=H, the DIMOUT logic asserts the PWM logic. The voltage of TC54 (5.4V) will decrease by
the constant current -10uA and is discharged to 2.4V.
③VOUT will be discharged and ILED decresing.
④When the voltage of TC54 pin is under 2.4V(typ.), the IC will shutdown.
○The setting method of TC54 external capacitance

Please use below formula to calculate the shutdown time TOFF.
CREG[ F ]  3.0 [V ]
TOFF  Sec]
[　
10 [A]
As shown the above, the PWM signal is required even after STB=L.
The discharge interval of VOUT is the longest in the minimum PWM duty. Please set the Creg value with a enough timing
margin from the end of the VOUT discharge to shutdown.
●3.4.3 The LED current setting

LED current can be adjusted by setting the resistance RISENSE which connects Vout
to ISENSE pin.
○the relationship between RISET and ILED current
With DC dimming ADIM [V ]

RISENSE  [ ] DIMOUT
I LED [ A]
Without DC dimming Error AMP
3.5[V ] ISENSE
RISENSE  [ ] -
I LED [ A] +
+ 3.5V ADIM
RISENSE
[setting example]
If ILED current is 400mA as ADIM is 1.5V, we can calculate RISENSE as below.
FB
ADIM [V ] 1.5[V ]
RISENSE    3.75[] 　
I LED [ A] 0.4[ A]
Figure 24. the example of LED

current setting
www.rohm.com
17/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●3.4.4. how to set DCDC oscillation frequency

RRT which connects to RT pin set the oscillation frequency of DCDC.
○ the relationship between OSC and RRT (ideal)
15000
R RT  [ k ]
f SW [ kHz ]
where fsw is the oscillation frequency of DCDC [kHz]
Frequency (fsw)
Ideal
GATE
RT CS
RRT Rcs
GND
Figure 25. RT pin setting example
This equation is an ideal equation in which correction factors are not applied.
The adequate verification with an actual set needs to be performed to set frequency precisely.
[setting example]
If DCDC oscillation frequency is 200kHz, we can calculate the RRT as below.
15000 15000
RRT    75 [ k] 　
f sw [ kHz ] 200[ kHz ]
www.rohm.com
18/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●3.4.5. how to set UVLO

Under voltage lock out pin for the input voltage of the power stage. More than 3.0V(typ.), IC starts boost operation and
stops lower than 2.7V(typ.).
The UVLO pin is high impedance, because the internal resistance to a certain bias is not connected.
So, the bias by the external components is required, even if UVLO function is not used, because the open connection of
The resistor value can be calculated by the below formula, if the VIN voltage is monitored, and that is divided by the
resistor R1, R2 like the below diagram.
○UVLO detection equality VIN

If VIN decreases, R1, R2 value is expressed the following formula by the
VINdet, the detect voltage of UVLO.
(VINDET [V ]  2.7[V ])
R1  R 2[k]  [k]
2.7[V ] R1
UVLO
+
○UVLO release equality ON/ OFF
2.7V/3.0V R2
By using the R1, R2 in the above equality, the release voltage of UVLO can be -
expressed as following. CUVLO
( R1[k]  R2[k])
VINCAN  3.0V  [V ]
[setting example]
R2[k]
Figure 26. UVLO setting example
If the normal input voltage, VIN is 24V, the detect voltage of UVLO is 18V,
R2 is 30k ohm, R1 is calculated as following.
(VINDET [V ]  2.7[V ]) (18[V ]  2.7[V ])

R1  R 2[k]   30[k]   170.0 [k]
2.7[V ] 2.7[V ]
By using these R1, R2, the release voltage of UVLO, VINcan can be calculated as following.
(R1[k]  R 2[k]) 170.0[k]  30[k]

VINCAN  3.0[V ]   3.0[V ]   20.0 [V ]
[V ]　
R 2[k] 30[k]
www.rohm.com
19/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●3.4.6. how to set OVP

The OVP terminal is the input for over-voltage protection of output voltage.
The OVP pin is high impedance, because the internal resistance to a certain bias is not connected.
So, the bias by the external components is required, even if OVP
VOUT
function is not used, because the open connection of this pin is not
fixed the potential.
The resistor value can be calculated by the below formula, if the R1
OVP
VOUT voltage is monitored, and that is divided by the resistor R1, OVP
+
R2 like the below diagram.
2.9V/3.0V R2
-
○OVP detection equality COVP
If the VOUT is boosted abnormally, VOVPdet is the detect voltage of
OVP, R1, R2 can be expressed by the following formula.
(VOVPDET [V ]  3.0[V ])
R1  R2[k]  [k]
3.0[V ]
○OVP release equality
By using the R1, R2 in the above equality, the release voltage of OVP, Figure 27. OVP setting example
VOVPcan can be expressed as following.
( R1[k]  R2[k])
VOVPCAN  2.9V  [V ]
R2[k]
[setting example]
If the normal output voltage, VOUT is 40V, the detect voltage of OVP is 48V, R2 is 10k ohm, R1 is calculated as
following.
(VOVPDET [V ]  3.0[V ]) (48[V ]  3[V ])
R1  R2[k]   10[k]   150 [k]
3.0[V ] 3[V ]
By using these R1, R2, the release voltage of OVP, VOVPcan can be calculated as following.
( R1[k]  R2[k]) 10[k]  150[k]
VOVPCAN  2.9[V ]   2.9[V ]   46.4 [V ]
[V ]　
R2[k] 10[k]
www.rohm.com
20/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●3.4.7. how to set the interval until latch off

BD9488 built in the counter by latch off time, that is performed by counting the oscillation clock which is set by the RT pin.
Since the common oscillation circuit is used for counting, the interval until latch off is corresponding to the 130k clock,
which the GATE pulse output continuously. Please refer the time chart of the operation from the detect abnormality to the
latch off in the section 3.7.
○latch off time

BD9488 starts the counting up from the detection of each abnormal state, falls to the latch off state when the following
interval has passed.
Only PWM=L input does not reset the timer counter, if the abnormal state continues.
RRT [] R [k]
LATCHTIME  217   130k  RT 7 [sec]
1.5  1010
1.5  10
Where LATCHTIME is the interval until latch off state
RRT is the connected resistor of RT pin.
[setting example]
If the resistor of RT pin is 100k ohm, the timer latch interval is as following.
RRT [k] 100[k]

LATCHTIME  130k   130k   866[m sec]　
1.5 107 1.5 107
www.rohm.com
21/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●3.5. DCDC parts selection

3.5.1. how to set OCP / the calculation method for the current rating of DCDC parts
BD9488 stops the switching by the OCP detect, when the CS pin voltage is more than 0.4V. The resistor value of CS pin,
RCS need to be considered by the coil L current. And the current rating of DCDC external parts is required more than the
peak current of the coil.
It is shown below that the calculation method of the coil peak current, the selection method of Rcs (the resistor value of
CS pin) and the current rating of the external DCDC parts.
(the calculation method of the coil peak current, Ipeak)

At first, since the ripple voltage at CS pin depend on the application L VOUT
condition of DCDC, those put onto the equality to calculate as following.
The output voltage = VOUT [V] VIN IL
LED total current = IOUT [A]
The DCDC input voltage of the power stage = VIN [V]
IOUT
The efficiency of DCDC =η[%]
fsw
And then, the averaged input current IIN is calculated by the following
equality
VOUT [V ]  I OUT [ A] GATE
I IN  [ A]
VIN [V ] [%] CS
Rcs
And the ripple current of the inductor L (ΔIL[A]) can be calculated by GND
using DCDC the switching frequency, fsw, as following.
(VOUT [V ]  V IN [V ])  V IN [V ]
Δ IL  [ A]
L[ H ]  VOUT [V ]  f SW [ Hz ]
(V)
On the other hand, the peak current of the inductor Ipeak can be
expressed as the following equality.
IL[ A]
Ipeak  I IN [ A]  [ A] … (1) N[V]
2
Therefore, the bottom of the ripple current Imin is
（A) (t)
IL[ A]
Im in  I IN [ A]  　 or 0 Ipeak
2
IIN ΔIL
As Imin>0, that operation mode is CCM (Continuous Current Mode),
otherwise another mode is DCM (Discontinuous Current Mode). Imin
IL[A]
(the selection method of Rcs)

Ipeak flows into Rcs and that cause the voltage signal to CS pin. (t)
（V)
(Please refer the right timing chart)
That peak voltage VCSpeak is as following. 0.4V
VCS peak  Rcs  Ipeak

VCS[V]
[V ]
VCSpeak
As this VCSpeak reaches to 0.4V, the DCDC output stops the switching.
Therefore, Rcs value is necessary to meet the under condition.
(t)
Rcs  Ipeak [V ]  0.4[V ]
Figure 28. Coil current waveform
(the current rating of the external DCDC parts)
The peak current as the CS voltage reaches to OCP level (0.4V) is defined as Ipeak_det.
0.4[V ]
I peak _ det  [ A] … (2)
Rcs[ ]
The relation among Ipeak (equality (1)), Ipeak_det (equality (2)) and the current rating of parts is required to meet the
following
I peak  I peak _ det  The current rating of parts
Please make the selection of the external parts to meet the above condition such as FET, Inductor, diode.
[setting example]
The output voltage = VOUT [V] = 40V
LED total current = IOUT [A] = 0.48V
The DCDC input voltage of the power stage = VIN [V] = 24V
www.rohm.com
22/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
The efficiency of DCDC =η[%] = 90%

The averaged input current IIN is calculated as the following.
VOUT [V ]  I OUT [ A] 40[V ]  0.48[ A]

I IN [ A]  
　  0.89 [ A]
VIN [V ] [%] 24[V ]  90[%]
And the ripple current of the inductor L (ΔIL[A]) can be calculated if the switching frequency, fsw = 200kHz, the inductor,
L=100μH.
(VOUT [V ]  V IN [V ])  V IN [V ] ( 40[V ]  24[V ])  24[V ]

Δ IL  
　  0.48 [ A]
L[ H ]  VOUT [V ]  f SW [ Hz ] 100  10  6 [ H ]  40[V ]  200  10 3 [ Hz ]
Therefore the inductor peak current, Ipeak is
IL[ A] 0.48[ A]
Ipeak  I IN [ A]  A]  0.89[ A] 
[　  1.13 [ A]
2 2
The calculation result of the peak current
If Rcs is assume to be 0.3 ohm
VCS peak  Rcs  Ipeak  0.3[  ]  1.13[ A]  0.339 [V ]  0.4V

The Rcs value confirmation
The above condition is met.
And Ipeak_det, the current OCP works is
0.4[V ]
I peak _ det   1.33 [ A]
0.3[ ]
If the current rating of the used parts is 2A,
I peak  I peak _ det  The current rating  1.13[ A]  1.33[ A]  2.0[ A]

The current rating confirmation of DCDC parts
This inequality meets the above relationship. The parts selection is proper.
And Imin, the bottom of the IL ripple current can be calculated as following.
IL[ A]
I MIN  I IN [ A]  [ A]  1.13[ A]  0.48[ A]  0.65[ A]  0 　
2
This inequality implies the operation is the continuous current mode.
www.rohm.com
23/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
3.5.2. Inductor selection

The inductor value affects the input ripple current. The equality in the section
3.5.1 is as following.
(VOUT [V ]  V IN [V ])  V IN [V ]
Δ IL  [ A]
ΔIL L[ H ]  VOUT [V ]  f SW [ Hz ]
VOUT [V ]  I OUT [ A]
VIN I IN  [ A]
VIN [V ] [%]
IL[ A]
Ipeak  I IN [ A]  [ A]
IL Where
2
L L: the coil inductance [H] Vout: the DCDC output voltage [V]
Vin: the input voltage [V]
VOUT Iout: the output load current (the summation of LED current) [A]
Iin: the input current [A] Fsw: the oscillation frequency [Hz]
If in the continuous current mode, Please set ⊿IL to 30% - 50% of the output
load current.
RCS COUT
Figure 29. the waveform and the circuit of

inductor current
* The current exceeding the rated current value of inductor flown through the coil causes magnetic saturation, results
in decreasing in efficiency. Inductor needs to be selected to have such adequate margin that peak current does not
exceed the rated current value of the inductor.
* To reduce inductor loss and improve efficiency, inductor with low resistance components (DCR, ACR) needs to be
selected
3.5.3. Output capacitance Cout selection

Output capacitor needs to be selected in consideration of equivalent series
VIN resistance required to even the stable area of output voltage or ripple voltage.
Be aware that set LED current may not be flown due to decrease in LED
IL terminal voltage if output ripple componet is high.
L Output ripple voltage ⊿VOUT is determined by Equation (4):
VOUT 1 I OUT 1
ΔVOUT  ILMAX  R ESR    　
[V ]　・・・・・　　
(4)
C OUT  f SW
where, RESR is the equivalent series resistance of Cout.
RESR
RCS COUT
Figure 30. the circuit of the output capacitor
* Rating of capacitor needs to be selected to have adequate margin against output voltage.
* To use an electrolytic capacitor, adequate margin against allowable current is also necessary. Be aware that the
LED current is larger than the set value transitionally in case that LED is provided with PWM dimming especially.
www.rohm.com
24/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
3.5.4. MOSFET selection

Though there is no problem if the absolute maximum rating is larger than the rated current of the inductor L, or is
larger than the sum of the tolerance voltage of COUT and the rectifying diode VF. The product with small gate
capacitance (injected charge) needs to be selected to achieve high-speed switching.
* One with over current protection setting or higher is recommended.
* The selection of one with small on resistance results in high efficiency.
3.5.5. Rectifying diode selection

A schottky barrier diode which has current ability higher than the rated current of L, the reverse voltage larger than the
tolerance voltage of COUT, and the low forward voltage VF especially needs to be selected.
www.rohm.com
25/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●3.6. Loop compensation

A current mode DCDC converter has each one pole (phase lag) fp due to CR filter composed of the output capacitor
and the output resistance (= LED current) and zero (phase lead) fZ by the output capacitor and the ESR of the
capacitor.
Moreover, a step-up DCDC converter has RHP zero (right-half plane zero point) fZRHP which is unique with the boost
converter. This zero may cause the unstable feedback. To avoid this by RHP zero, the loop compensation that the
cross-over frequency fc set as following, is suggested.
fc = fZRHP /5 (fZRHP: RHP zero frequency)
Considering the response speed, the below calculated constant is not always optimized completely. It needs to be
adequately verified with an actual device.
VIN VOUT
L ILED
VOUT
- FB
RESR gm
RCS
+ RFB1 CFB2
COUT
CFB1
Figure 31. the circuit of output stage and the error amplifier
i. Calculate the pole frequency fp and the RHP zero frequency fZRHP of DC/DC converter
fp 
I LED
[　
Hz ] 　 VOUT  (1  D) 2
f ZRHP  [　
Hz ]　　
2  VOUT  COUT 2  L  I LED
Where ILED = the summation of LED current, VOUT  VIN (Continuous Current Mode)
D 　
ii. Calculate the phase compensation of the error amp VOUT
output (fc = fZRHP/5)
f RHZP  RCS  I LED 1

R FB1  ] 　
[　 C FB1  [　
F ]　　
5  f p  gm  VOUT  (1  D) 2  RFB1  f p
Where
gm  4.0  10 4 [ S ]
iii. Calculate zero to compensate ESR (RESR) of COUT (electrolytic capacitor)
RESR  C OUT
C FB 2  [　
F] 　
RFB1
*When a ceramic capacitor (with RESR of the order of milliohm) is used to COUT, the operation is stabilized by
insertion of CFB2.
To improve the transient response, RFB1 need to be increase, CFB1 need to be decrease. It needs to be adequately verified
with an actual device in consideration of vary from parts to parts since phase margin is decreased.
www.rohm.com
26/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●3.7. Timing chart

3.7.1 starting up 1 (STB inputs and PWM signal succeeds)
VCC 7.5V
STB
PWM1
andPWM2
2.4V
2.5V 2.5V
TC54
V5UVLO
3.0V
1.1V 1.1V
SS
GATE
FAILB
OFF STANDBY SS Normal OFF SS
(Reset)
STANDBY
(*1) (*2) (*3) (*4) (*5)
(*1)…TC54 starts up if STB turns from L to H. The pin SS is not charged in the state that the PWM signal is not input, the boost
is not started.
(*2)…The charge of the pin SS starts by the positive edge of PWM=L to H, and the soft start starts. The GATE pulse outputs
only during PWM=H. And as the SS is less than 1.1V, the pulse does not output. The pin SS continues charging in spite of
the assertion of PWM and OVP.
(*3)…The soft start interval will end if the voltage of the pin SS, Vss reaches to 3.0V. By this time, BD9488 boost Vout where the
set LED current flows. It is started to monitor the abnormal detection of OPEN.
(*4)…As STB=L, instantaneously the boost operation is stopped. (GATE=L, SS=L) On the other hand, the discharge circuit
works in the interval “STB=L and V5UVLO=H”. Please refer to the time chart in the section 3.7.3 for details.
(*5)…As STB=H again, the boost operation restarts by the next PWM=L to H. It is the same operation as the timing of (*1).
Please refer to the section 3.4.1 for the setting of soft start external capacitance.
www.rohm.com
27/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
3.7.2 starting up 2 (PWM signal inputs and STB succeeds)
VCC 7.5V
STB
PWM1
andPWM2
2.4V
2.5V 2.5V
TC54
V5UVLO
3.0V
1.1V 1.1V
SS
GATE
FAILB
OFF SS ON OFF SS
(Reset)
STANDBY
(*1) (*2) (*3) (*4) (*5)
(*1)…TC54 starts up if STB turns from L to H.

(*2)…At the moment the release of V5UVLO (the UVLO of the pin TC54), or the time of the positive edge of PWM=L to H, the
soft start starts. The GATE pulse outputs only during PWM1=H. And as the SS is less than 1.1V, the pulse does not output.
The pin SS continues charging in spite of the assertion of PWM and OVP.
(*3)…The soft start interval will end if the voltage of the pin SS, Vss reaches to 3.0V. By this time, BD9488 boost Vout where the
set LED current flows. It is started to monitor the abnormal detection of OPEN.
(*4)…As STB=L, instantaneously the boost operation is stopped. (GATE=L, SS=L) On the other hand, the discharge circuit
works in the interval “STB=L and V5UVLO=H”. Please refer to the time chart in the section 3.7.3 for details.
(*5)…As STB=H again, it is the same operation as the timing of (*1).
www.rohm.com
28/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
3.7.3 turn off
STB
PWM1
andPWM2
TC54
2.4V
V5UVLO
DIMOUT
GATE
Vout
SS
ON Dischange OFF
(*1) (*2)
(*1)…As STB pin turns High to Low, BD9488F stops the boost operation, starts the discharge of TC54.
(*2)…During STB=L and V5UVLO=H, the DIMOUT asserts the same logic of PWM. TC54=5.4V is discharged until 2.4V by the
constant current 10uA. And IC turns off. Vout need to be discharged adequately so that LED does not turns on drastically
at the next start up.
For detailed instructions, please refer the section 3.4.2 “how to shutdown and set TC54 capacitance”
www.rohm.com
29/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
3.7.4 the soft start function
(*1)…The SS pin charge does not start by just STB=H. “PWM1=H and PWM2=H” is required to start the soft start. In the low SS
voltage, the GATE pin duty is depend on the SS voltage. And as the SS is less than 1.1V, the pulse does not output.
(*2)…By the low STB=L, the SS pin is discharged immediately.
(*3)…As the STB recovered to STB=H, The SS charge starts immediately by the logic “PWM1 and PWM2=H” in this chart.
(*4)…The SS pin is discharged immediately by the UVLO=L.
(*5)…The SS pin is discharged immediately by the VCCUVLO=L
(*6)…The SS pin is discharged immediately by the TC54UVLO=L
(*7)…The SS pin is not discharged by the abnormal detection of the latch off type such as OVP until the latch off
www.rohm.com
30/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
3.7.5 the OVP detection
(*1)…As OVP is detected, the output GATE=L, DIMOUT=L, and the CP counter starts
(*2)…If OVP is released within 4 clock of CP counter of the GATE pin frequency, the boost operation restarts.
(*3)…As the OVP is detected again, the boost operation is stopped.
(*4)…As the OVP detection continues up to 4 count by the CP counter, IC will be latched off.
(*5)…As the latched off, the boost operation doesn't restart even if OVP is released.
(*6)…The STB=L input can make IC reset. In this chart, DIMOUT asserts high by the discharge function in the paragraph 3.7.3.
(*7)…It normally starts as STB turns L to H.
(*8)…The operation of the OVP detection is not related to the logic of PWM.
www.rohm.com
31/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
3.7.6 LED OPEN detection
(*1)…During starting up, even if the normality, ISENSE<0.1V because of the low Vout. Therefore the OPEN detection will be
masked for the soft start period.
(*2)…In the same way, as PWM=L, ISENSE<0.1V because of DIMOUT=L. OPEN will be masked, too.
(*3)…Though the OPEN is detected if ISENSE<0.1V as the PWM=H, it is not judged immediately to abnormal state. The
behavior of GATE, FAILB keeps the normal operation.
(*4)…The CP counter will start if the OPEN detection continues 4 clock of the GATE frequency. The count stops if
ISENSE>0.1V.
(*5)…When the OPEN detection continues up to 130k count with the CP counter, IC will be latched off. At this time, it asserts
GATE=L, DIMOUT=L, FAILB=L for the first time.
(*6)…The latch off state can be reset by the STB=L.
(*7)…It normally starts by STB=L to H, in this figure.
www.rohm.com
32/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
3.7.7 LED OCP detection
(*1)…If ISENSE>4.0V, LEDOCP is detected, it becomes GATE=L. To detect LEDOCP continuously, The DIMOUT is
compulsorily high, regardless of the PWM dimming signal.
(*2)…When the LEDOCP releases within the GATE frequency 130k counts of the CP counter, the boost operation restarts.
(*3) …As the LEDOCP is detected again, the boost operation is stopped, too.
(*4)…If the LEDOCP detection continues up to 130k count with the CP counter, IC will be latched off.
(*5)…Once IC is latched off, the boost operation doesn't restart even if the LEDOCP releases.
(*6)…The latch off state can be reset by the STB=L. In this chart, DIMOUT asserts high by the discharge function in the
paragraph 3.7.3.
(*7)…It normally starts by STB=L to H.
(*8)…The operation of the LEDOCP detection is not related to the logic of the PWM.
www.rohm.com
33/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
3.7.8 the spontaneous detection OVP and OPEN.
STB
3.0V 3.0V 2.9V

OVP
INSENSE 0.1V
0.1V 0.1V
START
START
END
END
CP COUNTOR 4count 4count
SS 1.1V
GATE
DIMOUT
FAILB
STATE NORMAL COUNTOR Latch off OFF NORMAL COUNTOR Latch off
（Reset）
(*1) (*2) (*3) (*4) (*5)
(*1)…The time chart shows the OPEN detects faster and does not reach to the latch off state. The DIMOUT asserts high.
(*2)…If OPEN and OVP is detected spontaneously, OVP has the priority, and GATE=L, DIMOUT=L.
(*3)…IC will be latched off by the OVP factor.
(*4)…The latch off state is reset by the STB=L.
(*5)…The OVP has the priority too, in the case the OVP is detected first and the OPEN succeeds.
www.rohm.com
34/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
Operational Notes
1. Reverse Connection of Power Supply

Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
2. Power Supply Lines

Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3. Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
4. Ground Wiring Pattern

When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5. Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when
the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum
rating, increase the board size and copper area to prevent exceeding the Pd rating.
6. Recommended Operating Conditions

These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
7. Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush
current may flow instantaneously due to the internal powering sequence and delays, especially if the IC
has more than one power supply. Therefore, give special consideration to power coupling capacitance,
power wiring, width of ground wiring, and routing of connections.
8. Operation Under Strong Electromagnetic Field

Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
9. Testing on Application Boards

When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during
transport and storage.
10. Inter-pin Short and Mounting Errors

Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
www.rohm.com
35/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
Operational Notes – continued
11. Unused Input Pins

Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small
charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and
cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the
power supply or ground line.
12. Regarding the Input Pin of the IC

This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should
be avoided.
Figure xx. Example of monolithic IC structure
13. Ceramic Capacitor
When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with
temperature and the decrease in nominal capacitance due to DC bias and others.
14. Area of Safe Operation (ASO)

Operate the IC such that the output voltage, output current, and power dissipation are all within the Area of Safe
Operation (ASO).
15. Thermal Shutdown Circuit(TSD)

This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always
be within the IC’s power dissipation rating. If however the rating is exceeded for a continued period, the junction
temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls below
the TSD threshold, the circuits are automatically restored to normal operation.
Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no
circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from
heat damage.
16. Over Current Protection Circuit (OCP)

This IC incorporates an integrated overcurrent protection circuit that is activated when the load is shorted. This
protection circuit is effective in preventing damage due to sudden and unexpected incidents. However, the IC should
not be used in applications characterized by continuous operation or transitioning of the protection circuit.
www.rohm.com
36/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
●Ordering Information
B D 9 4 8 8 F XX
Part Number Package Packaging and forming specification

F:SOP18 XX: Please confirm the formal name to our sales.
●Physical Dimension Tape and Reel Information

SOP18
<Tape and Reel information>
11.2 ± 0.2
(MAX 11.55 include BURR) Tape Embossed carrier tape
18 10 Quantity 2000pcs
E2
7.8±0.3
5.4±0.2
Direction
The direction is the 1pin of product is at the upper left when you hold
of feed ( reel on the left hand and you pull out the tape on the right hand )
0.3MIN
1 9
0.15 ± 0.1
1.8±0.1
0.11
0.1
1.27 0.4 ± 0.1 Direction of feed
1pin
(Unit : mm) Reel ∗ Order quantity needs to be multiple of the minimum quantity.
●Marking Diagram (TOP VIEW)
SOP18(TOP VIEW)
Part Number Marking
B D 9 4 8 8 F LOT Number
1PIN MARK
www.rohm.com
37/38
TSZ22111・15・001 27.May 2014 Rev.003
BD9488F Datasheet
Revision History
Date Revision Changes

11.Jul.2012 001 New Release
p.2 The rating of STB pin is changed from 20V to VCC.
29.Dec.2013 002 p.5 The rating of STB pin is changed from 20V to VCC.
p.6 In the equivalent circuit of STB pin, the Diode of VCC side is added.
p.9,20 In OVP explanation, “over-voltage protection and short circuit protection” is
27. May 2014 003
changed to “over-voltage protection”.
www.rohm.com
38/38
TSZ22111・15・001 27.May 2014 Rev.003
Datasheet
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
(Note 1)
intend to use our Products in devices requiring extremely high reliability (such as medical equipment , transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN USA EU CHINA
CLASSⅢ CLASSⅡb
CLASSⅢ CLASSⅢ
CLASSⅣ CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice – GE Rev.002
© 2013 ROHM Co., Ltd. All rights reserved.
Datasheet
Precautions Regarding Application Examples and External Circuits

1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label

QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act

Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights

1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice – GE Rev.002
Datasheet
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or
concerning such information.
Notice – WE Rev.001
Datasheet
Buy
BD9488F - Web Page
Distribution Inventory
Part Number BD9488F

Package SOP18
Unit Quantity 2000
Minimum Package Quantity 2000
Packing Type Taping
Constitution Materials List inquiry
RoHS Yes

Boost 1channel White Led Driver For Large LCDS: Datasheet

Uploaded by

Copyright:

Available Formats

Boost 1channel White Led Driver For Large LCDS: Datasheet

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Boost 1channel White Led Driver For Large LCDS: Datasheet

Uploaded by

Copyright:

Available Formats

Datasheet

Boost 1channel white LED driver

●General Description ●Key Specifications

●Typical Application Circuit(s) VCC VIN

Figure 2. Typical application circuit

●Absolute Maximum Ratings (Ta=25℃)

●Pin Configuration ●Package dimension, marking diagram

Figure 3-1. Pin configuration Figure 3-2. Package dimension

●1.1 Electrical character (Unless otherwise specified Ta=25℃，VCC=12V)

●1.2 Electrical character (Unless otherwise specified Ta=25℃，VCC=12V)

●1.3 Pin number, pin name, pin function

●2.1.1 Pin ESD Type

RT PWM1, PWM2 FAILB

ADIM ADIM_P DIMOUT

GATE STB ISENSE

Figure 4-1. Internal equivalent circuit

●2.1.2 Pin ESD Type

Figure 4-2. Internal equivalent circuit

●2.2 Block diagram

Figure 5. Block diagram

●2.3 Typical performance Curves

●2.4 Pin function description

○Pin5, Pin6: PWM1, PWM2

State PWM input voltage

Figure 11. PWM pin function

Status FAILB output

Status DIMOUT output

[LED OCP Protection Function]

●3.1 Application circuit example

・The basic application circuit example

Figure 16. The basic application circuit example

Adim (DC) ADIM

PWM1 pin and PWM2 pin are shorted.

・Only analog dimming

Adim (DC) ADIM

Figure 19. the circuit example of analog dimming only

・Application example when use numerous IC

Figure 20. the circuit example of when plural IC is used.

●3.2 The detection condition list of the protection (TYP. Condition)

●3.3 The behavior list of the protection

●3.4 External components selection

○The explanation of start up sequency

○The setting method of SS external capacitance

●3.4.2 how to shutdown and set TC54 capacitance

Figure 23. the shutdown waveform and circuit

○Explanation of shutdown sequence

○The setting method of TC54 external capacitance

●3.4.3 The LED current setting

With DC dimming ADIM [V ]

Figure 24. the example of LED

●3.4.4. how to set DCDC oscillation frequency

○ the relationship between OSC and RRT (ideal)

where fsw is the oscillation frequency of DCDC [kHz]

Figure 25. RT pin setting example

●3.4.5. how to set UVLO

○UVLO detection equality VIN

(VINDET [V ]  2.7[V ]) (18[V ]  2.7[V ])

(R1[k]  R 2[k]) 170.0[k]  30[k]