Stephen Tsung-Han Sher

7555500940
WRIT 340 - T TH 9:30AM
Professor Townsend
April 9, 2014

Technical Description

The New Durable Rubik’s Cube

General Overview

The Rubik’s Cube is a 3-dimensional puzzle for all ages. The puzzle’s goal is to simply

match each of the six sides of the cube with the same color by turning each face one after

another. With approximately 43 quintillion1 possible arrangements, this simple toy offers a

complex puzzle experience. This technical paper will focus redesigning the original 3x3x3

Rubik’s Cube to improve its durability and reduce its complexity through means of using PVC

tiles and ball bearing movement.

1 exactly 43,252,003,274,489,856,000 unique permutations

Page 1 of 36
Table of Contents

1 History …………………………………………………………………………………...7

1.1 Preceding Designs ……………………………………………………………...8

1.2 Rubik’s Design …………………………………………………………………8

1.3 Modern Design …………………………………………………………………9

2 Design …………………………………………………………………………………… 10

2.1 Dimensions ………………………………………………..…………………... 10

2.2 Materials …………………………………………………..…………………... 10

2.3 Color …..…………………………………………………..…………………... 11

2.3.1 Color Composition …………………………………………………...11

2.3.2 Color Arrangement ………………………………………………….. 13

2.4 Components …………………………………………………………………….14

2.4.1 Core …………………………………………………………………..14

2.4.2 Cubelets ………………………………………………………………15

2.4.2.1 Edge Cubelet ……………………………………………… 15

2.4.2.2 Corner Cubelet …………………………………………….. 16

2.4.2.3 Center Cubelet …………………………………………….. 17

2.4.3 Screws ……………………………………………………………….. 18

2.4.4 Springs ………………………………………………………………. 18

2.5 Structure ………………………………………………………………………..19

2.5.1 Row Configurations …………………………………………………. 19

2.5.1.1 Corner-Edge-Corner Configuration ……………………….. 19

2.5.1.2 Edge-Center-Edge Configuration …………………………..20

Page 2 of 36
 2.5.1.3 Center-Core-Center Configuration …………………………21

2.5.2 Layer Configuration …………………………………………………. 22

2.5.2.1 Face Configuration ……………..…………………………. 22

2.5.2.2 Center Configuration ……………………………………….23

2.5.3 Cube Configuration …………………………………………………..24

2.6 Mechanics / Usage …………………………………………………………….. 25

3 Redesign ………………………………………………………………………………… 26

3.1 Color Indication Method ……………………………………………………….26

3.2 Ball-bearing movement ……………………………………………………….. 27

3.2.1 Ball Bearing………………………………………………………….. 28

3.2.2 Redesigned Components ……………………………………………. 28

3.2.2.1 Redesigned Core …………………………………………... 29

3.2.2.2 Redesigned Center Cubelet ……………………………….. 30

3.3 Construction ……………………………………………………………………31

3.4 Comparison ……………………………………………………………………. 32

3.4.1 Components …………………………………………………………. 33

3.4.2 Rotation Mechanism ………………………………………………… 34

3.4.3 Color Indication Method ……………………………………………. 34

3.4.4 Layer Extension ………………………………………………….…. 35

3.4.5 Customizability ……………………………………………………… 36

3.5 Improvements Summary ……………………………………………………….36


Page 3 of 36
List of Figures

1.1 ………… Nickols’ puzzle design …………………………………………………….. 7

1.2-a ……….. Rubik’s design ……….……………………………………………………..8

1.2-b ……….. Original Rubik’s Cube by Ideal Toy Corp ………………………………… 8

1.3 …………. Rubik’s Speed Cube ………………………………………………………..9

2.1 …………. Rubik’s Cube dimensions …………………………………………………. 10

2.3.1-a ……... A blank Rubik’s Cube …………………………………………………….. 11

2.3.1-b ……... Outer dimensions of cubelets and colored adhesives ……………………... 12

2.3.1-c ……... A solved Rubik’s Cube ……………………………………………………. 12

2.3.2 ……….. Color arrangement of the Rubik’s Cube …………………………………... 13

2.4.1 ……….. Schematic of a Rubik’s Cube core ………………………………………… 14

2.4.2.1 ……... Schematic for an edge cubelet …………………………………………….. 15

2.4.2.2 ……... Schematic for a corner cubelet ……………………………………………..16

2.4.2.3 ……... Schematic for a center cubelet …………………………………………….. 17

2.4.3 ……….. Wood screw used in the Rubik’s Cube ……………………………………. 18

2.4.4 ……….. Metal spring used in the Rubik’s Cube ……………………………………. 18

2.5.1.1 ……... Row type C-E-C configuration ……………………………………………. 19

2.5.1.2 ……... Row type E-C-E configuration ……………………………………………..20

2.5.1.3 ……... Row type C-C-C configuration ……………………………………………. 21

2.5.2.1 ……... Face layer configuration ……………………………………………………22

2.5.2.2 ……... Center layer configuration ………………………………………………… 23

2.5.3 ……….. Combining layers to construct the cube ……………………………………24

2.6 …………. Rotation methods ………………………………………………………….. 25

Page 4 of 36
3.1-a ……….. Typical worn down Rubik’s Cube…………………………………………. 26

3.1-b ……….. Application of PVC tiles using adhesives ………………………………….27

3.2.1.1 ……... Dimensions of a ball bearing ……………………………………………… 28

3.2.1.2 ……... Schematic of redesigned core ……………………………………………... 29

3.2.1.3 ……... Schematic of redesigned center cubelet ……………………………………30

3.3 …………. Assembly of ball bearing with the new core and center cubelet …………...31

3.4.4-a ……... Extension of the center cubelet from the core …………………………….. 34

3.4.4-b ……... Extension of entire face of the Rubik’s Cube ……………………………... 34

Page 5 of 36
List of Tables

2.1 …………. RGB values of Rubik’s Cube colors ………………………………………. 13

3.1 …………. Comparison between original and redesigned Rubik’s Cube ……………... 32

3.2 …………. Table of components in both the original and redesigned Rubik’s Cube …. 33


Page 6 of 36
1 History

Since the invention of the modern Rubik’s Cube in 1974 by Ernö Rubik, this toy has sold

over 350 million units, not including the sales of the many variations and imitations of the cube.

From the first prototype to the modern Speed Cube, there has only been two major design

changes in the Rubik’s Cube.

1.1 Preceding Design (1970 - 1972)

Larry Nichols invented the original concept of the puzzle in 1970. His invention was a

2x2x2 combinational puzzle held together by magnets (figure 1.1). Nichols patented his

invention on 1972, and called it the “Pattern Forming Puzzle and Method with Pieces Rotatable

in Groups”2. Nichols’ puzzle design was unsuccessful in sales.

Figure 1.1: Nichols’ puzzle patent

2 Patent publication number [US 3655201 A]

Page 7 of 36
1.2 Rubik’s Design (1974 - today)

Ernö Rubik, a Hungarian sculptor and architecture professor, invented the design of the

modern Rubik’s Cube, originally called the Magic Cube (figure 1.2-a) 3, in 1974.

Figure 1.2-a: Rubik’s original design (replica by Tony Fisher)

In 1975 Rubik redesigned his cube to consist of plastic interlocking pieces, the same

designed used today and the design discussed later in this paper. This design was far more

durable than Nichols’ magnetic design and became a success. In 1980, Rubik licensed his

invention to the Ideal Toy Corporation (figure 1.2-b) 4 and his toy made its international debut in

the same year. He also won the “German Game of the Year” award for the “Best Puzzle” in 1980.


Figure 1.2-b: Original Rubik’s Cube by Ideal Toy Corp.

3 Image source: Tony Fisher

4 Image source: John P. A. Carter

Page 8 of 36
1.3 Modern Design (2013 - today)

Rubik’s original design in 1975 was the only official Rubik’s cube design until 2013. In

2013 the Rubik’s Brand Ltd released the Rubik’s Speed Cube. Rubik’s Speed Cube consists of a

spherical core (figure 1.3.1)5, allowing smoother turning of the faces and reduced chances of

disassembly when turning the faces at high speeds. Albeit the Speed Cube having a better design,

the original Rubik’s Cube remains a widely popular option for the casual customer.


Figure 1.3: Partially disassembled Rubik’s Speed Cube

5 Image source: Rubik’s Brand Ltd

Page 9 of 36
2 Design

The Rubik’s Cube is a toy small enough to be carried comfortably in one hand; it is also

big enough for the user to be able to manipulate the toy with both hands with ease. Each of the

six faces of the cube is uniquely colored.

2.1 Dimensions

The cube measures 5.70 centimeters on each edge. Each face of the cube is partitioned

into nine smaller even cubes, called cubelets, in a 3-by-3 arrangement, with each cubelet’s outer-

facing edges measuring 1.90 centimeters (figure 2.1).

Figure 2.1: Rubik’s Cube dimensions

2.2 Materials

The entire cube is composed of polymer-based plastic: either low density polyethylene

(LDPE) or Polyvinyl-chloride (PVC). The only exception is the six metal screws and springs

holding the central core of the cube together. The color-indication method on the cube is done

using colored plastic adhesives composed of polyethylene terephthalate (PET).

Page 10 of 36
2.3 Color

The standard Rubik’s Cube follows a set color composition and arrangement. Any other

differing color composition or arrangements from what is described in this section are not

considered to be the standard Rubik’s Cube.

2.3.1 Color Composition

The main cube is black in color except the color-indication components and the central

core that is not visible at all times (figure 2.3.1-a)6 when the cube is fully assembled..

Figure 2.3.1-a: A blank Rubik’s Cube

6 Image source: of Rubik’s Brand Ltd.

Page 11 of 36
 Each outer face of the cubelets has a specific color assigned. Color-indication adhesive

components are squares measuring 1.70 centimeters, leaving a visible black border around each

cubelet (figure 2.3.1-b).

Each of the six faces of the Rubik’s Cube are indicated by unique solid colors: White,

yellow, red, blue, orange, and green.

1.70 cm

1.90 cm
Figure 2.3.1-b: Outer dimensions of a cubelet and colored adhesive

At the toy’s solved state, the same color is arranged on each face of the cube (figure

2.3.1-c)7, ergo each unique color is assigned to nine cubelet faces.

Figure 2.3.1-c: A solved Rubik’s Cube

7 Image source: of Rubik’s Brand Ltd.

Page 12 of 36
2.3.2 Color Arrangement

The standard color-arrangement is as follows: Red is opposite from blue, orange is

opposite from green, and white is opposite from yellow. The red, white, and blue color faces are

adjacent from one another and are arranged in a clockwise manner (figure 2.3.2).

Figure 2.3.2: Color arrangement of the Rubik’s Cube

The following table is the RGB values of the hues of the six colors used on the official

Rubik’s Cube.

RGB Value
Color
Red Green Blue

White 255 255 255

Red 137 18 20

Blue 13 72 172

Orange 255 85 37

Green 25 155 76

Yellow 254 213 47

Table 2.1: RGB values of the Rubik’s Cube colors

Page 13 of 36
2.4 Components

The entire cube is composed of one core and twenty-six cubelets, all held together by six

metal screws, six springs and all the cubelets interlocking with each other.

2.4.1 Core

The center of the cube is a plastic axial core constructed as three cylindrical tubes

intersecting one another at 90º from one another (figure 2.4.1). The length of each axial cylinder

is 1.90 cm; the outer diameter is 0.76cm and the inner diameter at 0.25cm. The core uses six

metal screws, one for each face, to hold the core and central cubelets together; the metal screws

are installed in the cylindrical tubes of each axle.

Figure 2.4.1: Schematic of Rubik’s Cube core

Page 14 of 36
2.4.2 Cubelets

The twenty-six cubelets can be categorized into three different types: edge, corner, and

center. The Rubik’s Cube is composed of twelve edge cubelets, eight corner cubelets, and six

center cubelets. The colored adhesives are applied to the outward facing sides of the cubelet.

2.4.2.1 Edge Cubelet (figure 2.4.2.1)

The edge cubelet has two outward facing sides. There is a rectangular prism protruding

from the inner edge of the cubelet, serving as the interlocking mechanism for the cube. The inner

corner of the two faces adjacent to both colored faces are truncated in order for circular rotation

with the other cubelets. The cubelet and the protrusion are hollowed out in order to reduce

weight without significant compromisation to structural integrity.

Figure 2.4.2.1: Schematic for edge cubelet

Page 15 of 36
2.4.2.2 Corner Cubelet (figure 2.4.2.2)

The corner cubelet has three outward facing sides. There is a smaller cube with three

rounded faces protruding from the inner corner of the cubelet, serving as the interlocking

mechanism for the cube. The rounded truncation of the protruding cube allows for circular

rotation with the other cubelets. The corner cubelet is hollow on the inside to reduce weight but

maintaining structural integrity.

Figure 2.4.2.2: Schematic for corner cubelet

Page 16 of 36
2.4.2.3 Center Cubelet (figure 2.4.2.3)

The center cubelet has one outward facing side. The face directly opposite from the

colored face has a cylindrical protrusion, hollowed at the center to allow a screw for attachment

to the core. The four inner edges of the cubelet are rounded outwards in order to allow circular

rotation with the other cubelets. The outward face is a square cap that snaps onto the cubelet to

conceal the screw. Beneath the cap reveals the interior chamber of the cubelet for the installment

and access to the spring and screw.

Figure 2.4.2.3: Schematic for center cubelet

Page 17 of 36
2.4.3 Screws

Six wood screws (figure 2.4.3) are used to hold the six center cubelets with the core. The

smooth shank of the wood screw allows smooth sliding of the screw against the inner surfaces of

the cubelet with each rotation of the cube, minimizing the damage done to the plastic surfaces

through prolonged usage.

Figure 2.4.3: Wood screw

2.4.4 Springs

Six springs (figure 2.4.4) will sit between the wood screw and the inner chamber of the

center cubelet. The spring will provide constant tension pulling the center cubelet against the

core, ensuring the entire cube being held together as one single unit.


Figure 2.4.4: Metal spring

Page 18 of 36
2.5 Structure

Each of the cubelets are interconnected to one another by the interlocking design of the

protrusion of the edge and corner cubelet. The center cubelet serves as an axial pivot point.

2.5.1 Row Configuration

Each row is either configured as corner-edge-corner, edge-center-edge, or center-core-

center. These row configurations will then be combined to form a layer configuration.

2.5.1.1 Corner-Edge-Corner Configuration (C-E-C)

The edge cubelet rests between two corner cubelets. The protrusions of the two corner

cubelets will be facing inwards towards the edge cubelet (figure 2.5.1.1). The sides of the corner

cubelet’s protrusions will rest against the inner edge of the edge cubelet, holding the corner

cubelets in place. The top of the protrusions of all three cubelets will align flush with each other.

The rounded edges of all three cubelet’s protrusions will align to form part of a circle (denoted

by dotted red line in figure 2.5.1.1).

Figure 2.5.1.1: Row type C-E-C configuration

Page 19 of 36
2.5.1.2 Edge-Center-Edge Configuration (E-C-E)

The center cubelet rests between two edge cubelets. The protrusions of the two edge

cubelets will be facing inward towards the center cubelet (figure 2.5.1.2). The bottom of the two

edge cubelet’s protrusions will rest above the inner edge of the center cubelet, holding the edge

cubelets in place. The top of the center cubelet’s protrusion will rest below the top of the edge

cubelet’s protrusion; this recess will make room of the core’s axial cylinders to connect with the

center cubelets. The rounded edges of the cubelets will align to form a part of a circle (denoted

by dotted red line in figure 2.5.1.2).


Figure 2.5.1.2: Row type E-C-E configuration

Page 20 of 36
2.5.1.3 Center-Core-Center Configuration (C-C-C)

The cube core rests between two center cubelets. The two center cubelets are connected

to the core by means of the wood screw. The wood screw will be threaded through the spring,

inserted, and fastened through the center cubelets. The cap will then be placed onto the center

cubelet to conceal the spring and screw (figure 2.5.1.2).


Figure 2.5.1.3: Row type C-C-C configuration

Page 21 of 36
2.5.2 Layer Configuration

Combining the three row configurations will result in the layer configurations. There are

two layer configurations: face layer and center layer. These layer configurations will then be

combined to form the entire cube.

2.5.2.1 Face Configuration

The face layer configuration is composed of two C-E-C rows and one E-C-E row

configuration. The two C-E-C rows will sandwich the single E-C-E rows (figure 2.4.2.1). The

corner cubelet’s protrusions will be resting against the two adjacent edge cubelet’s inner side and

adjacent the single center cubelet’s inner corner. The edge cubelet’s protrusions will only be

resting against the center cubelet’s inner edge. The center cubelet’s inner edges will be holding

all other eight cubelet in place, interlocking each cubelet with one another. The rounded edges of

the protrusions of the cubelets will form a circle, serving as the rotational track for each layer to

rotate against the other layers (denoted by dotted red circle in figure 2.5.2.1).


Figure 2.5.2.1: Face layer configuration

Page 22 of 36
2.5.2.2 Center Configuration

The center layer is composed of two E-C-E rows and one C-C-C row. The two E-C-E

rows will sandwich the one C-C-C row (figure 2.5.2.2). The protrusion of the edge cubelet will

rest against the inner edges of the center cubelets, holding the edge cubelet in place. The core

will be holding each of the four center cubelets together using the springs and screws. The

rounded inner edges of all eight cubelets will form a circle, serving as the rotational track for this

layer to rotate freely against the other layers (denoted by dotted red circle in figure 2.5.2.2).


Figure 2.5.2.2: Center layer configuration

Page 23 of 36
2.5.3 Cube Configuration

The twenty-six cubelets and the core can be combined to gather to form two face layers

and one center layer. By combining the two face layers with the single center layer in a sandwich

fashion (figure 2.5.3), the entire Rubik’s Cube will be assembled and completed.

Each protrusion of the edge and corner cubelets sits against one another and against the

center cubelet, and each center cubelet is held together with the core; this interconnection of the

cubelets interlocks all twenty-six cubelets together.

In this completed configuration, there will be six circular tracks formed by the rounded

inner edges of the cubelets. Each of these six circular tracks allows for each of the six layers to

rotate: the core mechanic of the Rubik’s Cube’s design.


Figure 2.5.3: Combining layers to construct cube

Page 24 of 36
2.6 Mechanics / Usage

The rearrangement of colors is achieved through rotating each face of the cube 90

degrees at a time. Each face can be rotated clockwise or counterclockwise (figure 2.5.4). With

each of the six faces having two degrees of movement, this totals to twelve possible rotation

options on the cube.

Figure 2.5.4: Rotation methods

With each 90 degree rotation, the corner and edge cubelets aligns with the edge and

center cubelets of the adjacent face’s cubelets, allowing for subsequent rotations to occur in any

of the twelve choices.

Each rotation will displace all four corner and all four edge cubelets to the adjacent face

corresponding to the direction of the rotation, transposing the arraignment of the colors. Only the

center cubelets never displace due to the rotations pivoting around the center cubelets. Therefore

the color of the center cubelet on each of the six faces indicate the color of the entire face when

the puzzle is completed in its final color arrangement.


Page 25 of 36
3 Redesign

The traditional Rubik’s Cube’s design has been used for over forty years. However there

is a flaw in the design that has never been fixed: durability. The two components of the Rubik’s

Cube that lacks durability are the color indication stickers and the rotational mechanism. The

redesign will address both flaws.

3.1 Color Indication Method

The traditional method of using colored stickers on the Rubik’s Cube has a major flaw in

its durability. The corners of the stickers peel easily and is easily subject to wear (figure 3.1-a) 8.

Even the professional grade stickers for professional speed-cubers has a lifespan of

750,000 rubs. This results in either constant replacement of stickers or of the entire cube itself.

Figure 3.1-a: Typical worn down Rubik’s Cube

8 Image source: Helen W. Chang

Page 26 of 36
 In order to greatly improve the durability and lifespan of the color-indication method,

PVC colored tiles can be used instead. This can be easily implemented by applying a strong

adhesive or epoxy to the back side of the tile and binding the tile to the face of the cubelets

(figure 3.1-b).

Plastic colored tiles eliminate the problem of the stickers wearing down. Furthermore, by

using a strong adhesive to attach the tiles to the cubelet’s faces, the tiles eliminate the issues of

peeling, tearing, or being inadvertently removed.

Colored PVC tile

Figure 3.1-b: Application of colored PVC tiles using adhesives

Page 27 of 36
3.2 Ball Bearing Movement

Instead of using a spring and wood screw to connect the core to the center cubelets, using

a ball bearing can smoothen rotations, reduce the number of components, and reduce assembly

steps.

3.2.1 Ball Bearing

The type of ball bearing used will be a deep-groove radial ball bearing. This component

will be constructed from heavy-duty steel to ensure maximum durability. The ball bearing will be

of a cylindrical shape, with the outer diameter at 0.50 cm, the inner diameter at 0.25 cm, and the

height at 0.50 cm. Due to the small dimensions, the additional six ball bearings added to the

Rubik’s cube will not increase the overall weight by any significant amount.

Figure 3.2.1.1: Schematic of ball bearing

3.2.2 Redesigned Components

This redesigned Rubik’s Cube using ball bearing movement will consist the redesigning

of two existing components, the center cubelet and the core. As a result, this redesign will

eliminate three components in the original design: the wood screw, spring, and center cubelet

cap.


Page 28 of 36
3.2.2.1 Redesigned Core

To install the ball bearing onto the core, the core will now have an additional cylindrical

protrusion from each of the six axial ends (figure 3.2.1.2). Each protrusion will measure 0.50 cm

in length and 0.25 cm in diameter. Since wood screws are no longer used, it is no longer

necessary to mill cylindrical channels down the middle of the axles. The core will still be

composed of LDPE or PVC, ensuring the structural integrity of the protrusions, thus the

protrusions will not likely be subject to breaking or fracturing.

Figure 3.2.1.2: Schematic of redesigned core

Page 29 of 36
3.2.2.2 Redesigned Center Cubelet

The cylindrical axle will have a cylindrical recess in order to house the ball bearing

component. This recess will be milled a depth of 0.50 cm and a diameter of 0.50 cm. Due to the

elimination of the wood screw and spring, the center cubelet no longer needs a cap nor interior

chamber.


Figure 3.2.1.3: Schematic of redesigned center cubelet

Page 30 of 36
3.3 Construction

Assembly of the the ball bearing occurs in two steps. The ball bearing is first inserted

onto the protrusion on the core’s axles, the center cubelet will then be inserted onto the ball

bearing afterwards (figure 3.3). The resulting construction will have the ball bearing acting as a

rotational interface between the core and the center cubelet, housed onto the core’s protrusions

and inside the center cubelet’s recess.

An epoxy or other binding agent will be used on the metal-polymer interface in the

attachment of the ball bearing, eliminating the possibility of deconstruction of the ball bearing

interface.

This construction replaces all core-center-cubelet attachment steps. All other procedures

in the construction of the cube remains the same.


Apply epoxy or binding agent here

Figure 3.3: Assembly of ball bearing with the new core and center cubelet

Page 31 of 36
3.4 Comparison

The following table summarizes the features and specifications between the original

Rubik’s Cube and the redesigned Rubik’s Cube. Detailed discussion on each feature and

specification will follow afterwards.

Original Redesigned

Components 99 87

Rotation mechanism Spring and wood screw Steel deep groove radial ball bearing

Color indication method PET stickers PVC colored tiles

Layer extension Variable Restricted

Customzability Free Restricted

Table 3.1: Comparison between original and redesigned Rubik’s Cube

Page 32 of 36
3.4.1 Components

The ball bearing component replaces the wood screw and spring components in the

original cube; in addition, using the ball bearing eliminates the need to access the interior

chamber of the center cubelet, therefore eliminating the need for the center cubelet cap. Both

designs still requires 54 color indication components (9 components for each of the 6 colors), 26

cubelets and a single core. The redesigned cube requires 12 less components than the original.

Furthermore, the reduced components and simplified design reduces the number of assembly

steps required, quickening the production of each unit. The following table lists the components

in both the original and redesigned Rubik’s Cube.

Original Rubik’s Cube Redesigned Rubik’s Cube

Sticker (red) x 9 PVC Tile (red) x 9

Sticker (blue) x 9 PVC Tile (blue) x 9

Sticker (white) x 9 PVC Tile (white) x 9

Sticker (orange) x 9 PVC Tile (orange) x 9

Sticker (green) x 9 PVC Tile (green) x 9

Sticker (Yellow x 9 PVC Tile (Yellow x 9

Core x 1 Core x 1

Center cubelet x 6 Center cubelet x 6

Edge cubelet x 12 Edge cubelet x 12

Corner cubelet x 8 Corner cubelet x 8

Center cubelet cap x 6 Ball bearing x6

Wood screws x 6

Springs x 6

Total 99 components Total 87 components

Table 3.2: Table of components used in both original and redesigned Rubik’s Cube

Page 33 of 36
3.4.2 Rotation Mechanism

The rotation mechanism of the original cube comprises of a spring and wood screw

holding the core and center cubelets together. As a result each rotation is resisted by the frictional

forces between the core and center cubelets. Using the ball bearing mechanism eliminates this

friction, resulting in significantly smoother and more consistent rotations. The ball bearing is

composed of steel, however due to the small dimensions of the ball bearing, this will not add any

significant weight to the final product.

3.4.3 Color Indication Method

The redesigned cube uses PVC colored tiles. PVC tiles is not subject to wear, loss of

color when rubbed, nor will it peel after extensive use. However, these tiles will result in an

increase in storage space, albeit not a significant amount. Taking into account off all the reduced

number of components, the net storage space for all the components of the redesigned cube will

still be less than that of the original Rubik’s Cube.

Page 34 of 36
3.4.4 Layer Extension

Layer extension refers to the degree in which the center cubelet can extend from the core.

In the original model, due to the spring mechanism, the center cubelet can be extended outwards

(figure 3.4.4-a), ergo extending the entire face layer outwards (denoted by red line in figure

3.4.4-b) to a small extent. This allows for greater maneuverability and flexibility in the

manipulation of the cube. The newer design binds the ball bearing to both the core and cubelet,

no longer allowing this extension to happen. However the average user will not concerned with

optimizing the performance of the cube, ergo not significantly impacting the target audience.

Figure 3.4.4-a: Extension of the center cubelet from the core

Figure 3.4.4-b: Extension of entire face of the Rubik’s Cube

Page 35 of 36
3.4.5 Customizability

The original design of the Rubik’s Cube allows its users to adjust the tightness of the

screw and the stiffness of the spring to suit the cube’s performance for each individual user. In

the redesigned version, there is no such area for customizability. However, the average user of

the Rubik’s Cube will not consider customizing their Rubik’s Cube; customization is only

necessary for those who want to pursue speed-cubing and solve the Rubik’s Cube competitively.

The consumers who want to customize their cube and pursue speed-cubing will be

investing in the Rubik’s Speed Cube instead of the classic Rubik’s Cube; therefore, this

restriction in the redesigned cube will not significantly impact the intended audience.

3.4.6 Improvements Summary

From the consumer’s perspective, the redesigned Rubik’s Cube provides more durable

color-indication components, as well as smoother and more consistent rotation movement. The

reduced customizability and flexibility in complex maneuvers are unrelated to the target audience

of this product.

From the supplier’s perspective, the redesigned Rubik’s Cube reduces the number of

individual components in cube as well as reduced assembly procedures, allowing faster and

cheaper production.

Page 36 of 36