1

ID- OCT. 2016

Conbextra GP constructive solutions

General purpose non-shrink cementitious grout

Uses Standards compliance

Conbextra GPA meets or exceeds the test requirements
Conbextra GP general purpose grouting is used where it
of ASTM C 1107.
is essential to eliminate shrinkage when completely filling
the void between a base plate and a substrate. Such an Description
application would be the grouting of a stanchion and
Conbextra GP cementitious grout is supplied as a ready to
machinery-base plates. It can also be used for anchoring
use dry powder. The addition of a controlled amount of
a wide range of fixings. These include masts, anchor
clean water produces a flowing non-shrink grout for gap
bolts, fence posts and around pipe sleeves.
thicknesses up to 100 mm.
Conbextra GP is a blend of Portland cement, graded fillers
Advantages
and chemical additives which impart controlled expansion
 Gaseous expansion system compensates for in the plastic state whilst minimising water demand. The
shrinkage and settlement in the plastic state.
low water demand ensures high early strength. The
 No metallic iron content to cause staining.
 graded filler is designed to assist uniform mixing and
 Prepack material overcomes potential on-site produce a consistent grout.
batching variations.
 Develops high early strength without the use of
chlorides.
 High ultimate strength and low permeability ensure the
durability of the hardened grout.
 

Typical detail of stanchion base plate

P age |1
 1

ID- OCT. 2016

Conbextra GP constructive solutions

Properties Instructions for use

The following results were obtained at a water:powder

Preparation
ratio of 0.18 and temperature of 25°C.
Concrete surface
Compressive strength
2
The substrate surface must be free from oil, grease or
(ASTM C109/C109M) : 26 N/mm @ 1 day
2
any loosely adherent material. If the concrete surface is
With tolerance 10% 55 N/mm @ 7 days
2 defective or has laitance, it must be cut back to a sound
65 N/mm @ 28 days
Flexural strength
(EN 196), tolerance min. base. Bolt holes and fixing pockets must be blown clean
2
15% : 10 N/mm @ 28 days of any dirt or debris.
Time for expansion Pre-soaking
Start : 15 to 20 minutes
Finish : 1.5 to 2 hours For a minimum of 2 hours prior to grouting, the area of
3
Fresh wet density : Approximately 2170 kg/m cleaned substrate should be flooded with fresh water.
Expansion characteristics Imme-diately before grouting takes place, any free water
ASTM C940 : Up to 2% @ 24 hours should be removed. Particular care should be taken to
blow out all bolt holes and pockets.
Specification Base plate
Performance specification
It is essential that this is clean and free from oil, grease
All grouting where shown on the drawing must be or scale. Air pressure relief holes should be provided
carried out with a pre-packaged cement based product to allow venting of any isolated high spots.
which is chloride-free. Levelling shims
It shall be mixed with clean water to the required
If these are to be removed after the grout has hardened,
consistency.
The plastic grout must not bleed or segregate. they should be treated with a thin layer of grease.
Formwork
A positive volumetric expansion shall occur while the
grout is plastic by means of a gaseous system. The formwork should be constructed to be leakproof. This
can be achieved by using foam rubber strip or mastic sealant
The storage, handling and placement of the grout must
beneath the constructed formwork and between joints.
be in strict accordance with the manufacturer’s
instructions. In some cases it is practical to use a sacrificial semi-dry
sand and cement formwork. The formwork should include
Supplier specification
outlets for pre-soaking.
All grouting where shown on the drawing must be carried Unrestrained surface area
out using Conbextra GP manufactured by Fosroc and
used in accordance with the manufacturer’s data sheet. This must be kept to a minimum. Generally the gap width
between the perimeter formwork and the plate edge
should not exceed 75 mm on the pouring side and 25 mm
on the opposite side. It is advisable where practical to
have no gap at the flank sides.

P age |2
 1

ID- OCT. 2016

Conbextra GP constructive solutions

Mixing
Pouring should be from one side of the void to eliminate
For best results a mechanically powered grout mixer any air or pre-soaking water becoming trapped under
should be used. When quantities up to 50 kg are used, a the base-plate. It is advisable to pour the grout across
slow speed drill fitted with a Fosroc Mixing Paddle (MR3) the shortest distance of travel. The grout head must be
should be used. maintained at all times so that a continuous grout front
Larger quantities will require a high shear vane mixer. Do is achieved.
not use a colloidal impeller mixer. Where large volumes have to be placed Conbextra GP
may be pumped. A heavy duty diaphragm pump is
To enable the grouting operation to be carried out recommended for this purpose. Screw feed and piston
continuously, it is essential that sufficient mixing capacity pumps may also be suitable.
and labour are available. The use of a grout holding tank
with provision to gently agitate the grout may be required. Curing

On completion of the grouting operation, exposed

Consistency of grout mix
areas should be thoroughly cured. Suggest curing
The quantity of clean water required to be added to a with Concure 1315. There is no need to remove
25 kg bag to achieve the desired consistency is given Concure 1315 as it will provide some protection and
below. won’t yellow. If using wet Hessian and plastic
sheeting then leave for at least seven days
Trowellable : 3.4 - 3.6 litres per 25kg bag – especially if exposed to sunlight.
Flowable : 4 - 4.5 litres per 25kg bag
Cleaning

The selected water content should be accurately Conbextra GP should be removed from tools and
measured into the mixer. The total contents of the equipment with clean water immediately after use. Cured
Conbextra GP bag should be slowly added and material can be removed mechanically, or with Fosroc
†
continuous mixing should take place for 5 minutes. This Acid Etch* .
will ensure that the grout has a smooth even consistency. Sampling procedure
Placing Cementitious grouts cannot be tested as concrete.
At 25°C place the grout within 15 minutes of mixing to Special sampling procedure are required refer to your
gain full benefit of the expansion process. local Fosroc office for further details.

Conbextra GP can be placed in a minimum thickness of Typical hopper system

Removable hopper: For larger pours the grout may be
10mm up to a maximum thickness of 100mm in a single hand placed or pumped into a removable hopper (trough).
pour when used as an underplate grout. For thicker
sections it is necessary to fill out Conbextra GP with well
graded 10mm, silt free aggregate to minimise exothermic.
If bulking with aggregate is used the ratio shall not exceed
1:1. Contact Fosroc for details of pre-bagged supply. The
properties of a bulked grout will differ from those
published in this data sheet.

Any bolt pockets must be grouted prior to grouting

between the substrate and the base plate.

Continuous grout flow is essential. Sufficient grout must

be prepared before starting. The time taken to pour a
batch must be regulated to the time taken to prepare the
next one.

P age |3
 1

ID- OCT. 2016

Conbextra GP constructive solutions

High temperature working

Precautions
It is suggested that, for temperatures above 35°C, the
Health and safety
following guidelines are adopted as good working
practice: Conbextra GP is alkaline and should not come into
contact with skin and eyes. Avoid inhalation of dust
 Store unmixed material in a cool (preferably
temperature controlled) environment, avoiding during mixing.
exposure to direct sunlight. Gloves, goggles and dust mask should be worn.

If contact with skin occurs, wash with water.

 Keep equipment cool, arranging shade protection if
Splashes to eyes should be washed immediately with
necessary. It is especially important to keep cool those
plenty of clean water and medical advice sought.
surfaces of the equipment which will come into direct
contact with the material itself.
Fire
 Try to eliminate application during the hottest times of
the day and in direct sunlight. Conbextra GP is non-flammable.

 Make sufficient material, plant and labour

Additional Information
available to ensure that application is a
continuous process. Fosroc manufactures a wide range of complementary
products which include :
 Water (below 20°C) should be used for mixing
the grout prior to placement.  Waterproofing membranes & waterstops
Limitations  Joint sealants & filler boards
 Cementitious & epoxy grouts
- Should not be placed in any unrestrained situation.
 Specialised flooring materials
- However, can be used for bolt holes or pockets.
- For further details contact Fosroc. Fosroc additionally offers a comprehensive package of
products specifically designed for the repair and
Estimating refurbishment of damaged concrete. Fosroc’s ‘Systematic
Approach’ to concrete repair features the following :
Supply
 Hand-placed repair mortars
Conbextra GP : 25 kg bags
 Spray grade repair mortars
Yield  Fluid micro-concretes
Trowellable : 12 litres per 25kg bag  Chemically resistant epoxy mortars
Flowable : 13.25 litres per 25kg bag  Anti-carbonation/anti-chloride protective coatings
 Chemical and abrasion resistant coatings
Note: Allowance should be made for wastage when
estimating quantities required. For further information on any of the above, please consult
your local Fosroc office-as below.
Storage

Conbextra GP has a shelf life of 12 months if kept in a

dry store within the range of 20 - 35°C in its original
packaging. If stored in high temperature and high
humidity locations the shelf life will be reduced.

P age |4
 1

ID- OCT. 2016

Conbextra GP constructive solutions

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the

PT.FOSROC Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control

Indonesia over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or
not in accordance with any advice, specification, recommendation of information given by it.

Jl.Akasia II Blok A8 No.1

Delta Silicon Industrial Park telephone: fax: email:
Lippo Cikarang
+62 21 897 2103-06 +62 21 897 2107 [email protected]
Bekasi 17550
Indonesia +62 21 89907783
www.fosroc.com

P age |5