Potable Water Approvals

ANSI/NSF 02.06
1.0 APPROVALS/LISTINGS
The information provided within this document is based on the latest approval and listing data at the time of
publication. Approvals/Listings are subject to change by the approvals agencies. Contact Victaulic or the corresponding
agency for the latest approvals and listings.

2.0 GASKETS/SEALS/O-RINGS
The following Victaulic Gaskets/Seals/O-Rings are agency tested and approved for use in potable water systems.
Reference should always be made to the approval agency, the approval, any exceptions listed below, and in the case
of ANSI/NSF 61, please also refer to the potable water operating temperature rating.

Victaulic Gasket/Seal ANSI/NSF 61 ANSI/NSF 372

Operating
Agency Temperature Rating Agency
cold +73°F/+23°C
Grade E
and hot +180°F/+82°C
cold +73°F/+23°C
Grade EW
and hot +180°F/+82°C
cold +73°F/+23°C
Grade EHP
and hot +180°F/+82°C
cold +73°F/+23°C
Grade E2
and hot +180°F/+82°C
Grade EPW UL Classified cold +73°F/+23°C UL Classified

Grade CHP cold +86°F/+30°C

(For Series 608N Only) and hot +180°F/+82°C
Grade M cold +86°F/+30°C
Grade E cold +73°F/+23°C
(For Vic-Press Sch 10S Only) and hot +180°F/+82°C
Grade H cold +73°F/+23°C
(For Vic-Press Sch 10S Only) and hot +180°F/+82°C

ALWAYS REFER TO ANY NOTIFICATIONS AT THE END OF THIS DOCUMENT REGARDING PRODUCT INSTALLATION, MAINTENANCE OR SUPPORT.

System No. Location Spec Section Paragraph

Submitted By Date Approved Date

victaulic.com
02.06 7795 Rev G Updated 07/2016 © 2016 Victaulic Company. All rights reserved.
1
victaulic.com

3.0  MECHANICAL COUPLINGS

Potable water approvals are based on testing of a product's wetted components. In the case of most Victaulic
mechanical couplings, the gasket/seal/o-ring is the only wetted component, therefore the use of a coupling in potable
water applications is strictly dependent upon the potable water and low lead approval of the gasket/seal/o-ring.
Reference the chart below for potable water ANSI/NSF 61 and ANSI/NSF372 compliant gaskets/seals/o-rings.
Victaulic's Bolted Split Sleeve Couplings are an exception to this rule. These products are designed with additional
wetted surfaces and therefore must carry their own individual approvals. The following Victaulic Bolted Split Sleeve
Couplings are agency tested and approved for use in potable water systems. Always refer to the certifying agency for
approved temperature ratings and any specific model details.

Victaulic Mechanical Couplings ANSI/NSF 61 ANSI/NSF 372

Operating
Agency Temperature Rating Agency

BOLTED SPLIT SLEEVE COUPLINGS

Style 230 Non-Restrained Flexible Coupling

Style 232 Restrained Flexible Coupling NSF Certified cold +73°F/+23°C NSF Certified

Style 233 Restrained Flexible Coupling for

Dynamic Joint Deflection

02.06 7795 Rev G Updated 07/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 2
victaulic.com

4.0 FITTINGS
The following Victaulic Fittings are agency tested and approved for use in potable water systems. Reference should
always be made to the approval agency, the approval, any approval specifics listed below, the gasket/seal/o-ring if
applicable, and in the case of ANSI/NSF 61, please also refer to the potable water operating temperature rating.
Potable water approvals are based on testing of a product's wetted components. In the case of mechanical tees, the
gasket/seal/o-ring and the body material are wetted components, therefore the use of a mechanical tee in potable
water applications is strictly dependent upon the potable water and low lead approval of the gasket/seal/o-ring and
the body material combined. The chart below is the complete product assembly approval and includes the operating
temperature rating that corresponds to ANSI/NSF 61 for the product listed.

Victaulic Fittings ANSI/NSF 61 ANSI/NSF 372

Approval Specifics Gasket/Seal/O-Rings Operating
(if applicable) (if applicable) Agency Temperature Rating Agency
COPPER
Installation-Ready™ Fittings cold +73°F/+23°C
Grade EHP Only UL Classified UL Classified
for Grooved Copper and hot +180°F/+82°C
Grooved Copper Fittings cold +86°F/+30°C
NSF Certified NSF Certified
(Wrot and/or Cast) and hot +180°F/+82°C
Style 622 Mechanical-T® Bolted
Body Material
Branch Outlet and Cross Grade E Only
C89836
Assembly for Grooved Copper
cold +73°F/+23°C
UL Classified UL Classified
and hot +180°F/+82°C
Style 647
Dielectric Fitting

STAINLESS STEEL
Sch 5S, 10S and Sch 40S cold +86°F/+30°C
Stainless Steel Fittings NSF Certified NSF Certified
Only and hot +180°F/+82°C
Grade E Only
Vic-Press®
Sch 10 Only UL Classified UL Classified
Stainless Steel Fittings
Grade H Only cold +73°F/+23°C
and hot +180°F/+82°C
Style 422 Mechanical-T®
Bolted Branch Outlet Grade E Only NSF Certified NSF Certified
for Stainless Steel

GALVANIZED
Standard
cold +86°F/+30°C
Grooved Fittings 1
Style 920/920N Galvanized Only UL Classified UL Classified
Mechanical-T® Bolted Grade E Only cold +73°F/+23°C
Branch Outlet
AQUAMINE®
Aquamine Pipe
NSF Certified cold +73°F/+23°C NSF Certified
and Fittings
DUCTILE IRON
Cement lined with a
AWWA Fittings NSF Certified cold +73°F/+23°C
standard asphalt coating
1  No.10 90° Elbow, No. 11 45° Elbow, No. 12 22 ½° Elbow, No. 13 11 ¼° Elbow, No. 100 90° Long Radius Elbow, No. 110 45° Long Radius Elbow,
No. 20 Tee, No. 25 Tee with Grooved Branch, No. 30 45° Lateral, No. 60 Cap, No. 50 Concentric Reducer, No. 51 Eccentric Reducer.

02.06 7795 Rev G Updated 07/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 3
victaulic.com

5.0  VALVES/FLOW CONTROL DEVICES

The following Victaulic Valves are agency tested and approved for use in potable water systems. Reference should
always be made to the approval agency, the approval, any exceptions listed below, the gasket/seal/o-ring if applicable,
and in the case of ANSI/NSF 61, please also refer to the potable water operating temperature rating.
Potable water approvals are based on testing of a product's wetted components. In the case of valves/flow control
devices, the gasket/seal/o-ring and the body material are wetted components, therefore the use of a valve/flow
control device in potable water applications is strictly dependent upon the potable water and low lead approval of the
gasket/ seal/o-ring and the body material combined. The chart below is the complete product assembly approval and
inlcudes the operating temperature rating that corresponds to ANSI/NSF 61 for the product listed.

Victaulic Valves/Flow ANSI/NSF 61 ANSI/NSF 372

Control Devices Approval Specifics Gasket/Seal/O-Rings Operating
(if applicable) (if applicable) Agency Temperature Rating Agency
COPPER
cold +86°F/+30°C
Series 608N Butterfly Valve Grade CHP Only UL Classified UL Classified
and hot +180°F/+82°C
CARBON STEEL
Series 761 VIC®-300
Grade E Only UL Classified UL Classified
MasterSealTM Butterfly Valve
Series 7A2 Butterfly Valve Grade E Only cold +73°F/+23°C
NSF Certified NSF Certified
Series 7B2 Butterfly Valve Grade E Only

STAINLESS STEEL

Series 415 Check Valve

High flow, high velocity
Series 465 Plug Valve cold +73°F/+23°C
applications only 2
UL Classified UL Classified
Series 466 Plug Valve
Series P569 Vic-Press® cold +73°F/+23°C
Stainless Steel Ball Valve and hot +180°F/+82°C
Series 76X - ICSS Low Lead
Balancing Valve cold +73°F/+23°C
NSF Certified NSF Certified
Series 461 VIC®-300 MasterSealTM and hot +180°F/+82°C
Grade E Only
Stainless Steel Butterfly Valve
2  Reference ANSI/NSF 61 - 2012, sec. 3.3.2.

User Responsibility for Product Selection and Suitability Note

Each user bears final responsibility for making a determination as to the suitability of This product shall be manufactured by Victaulic or to Victaulic specifications. All products
Victaulic products for a particular end-use application, in accordance with industry to be installed in accordance with current Victaulic installation/assembly instructions.
standards and project specifications, as well as Victaulic performance, maintenance, Victaulic reserves the right to change product specifications, designs and standard
safety, and warning instructions. Nothing in this or any other document, nor any verbal equipment without notice and without incurring obligations.
recommendation, advice, or opinion from any Victaulic employee, shall be deemed to Installation
alter, vary, supersede, or waive any provision of Victaulic Company's standard conditions Reference should always be made to the Victaulic installation handbook or installation
of sale, installation guide, or this disclaimer. instructions of the product you are installing. Handbooks are included with each shipment
Intellectual Property Rights of Victaulic products, providing complete installation and assembly data, and are available
No statement contained herein concerning a possible or suggested use of any material, in PDF format on our website at www.victaulic.com.
product, service, or design is intended, or should be constructed, to grant any license Warranty
under any patent or other intellectual property right of Victaulic or any of its subsidiaries Refer to the Warranty section of the current Price List or contact Victaulic for details.
or affiliates covering such use or design, or as a recommendation for the use of such
material, product, service, or design in the infringement of any patent or other intellectual Trademarks
property right. The terms “Patented” or “Patent Pending” refer to design or utility patents Victaulic and all other Victaulic marks are the trademarks or registered trademarks of
or patent applications for articles and/or methods of use in the United States and/or other Victaulic Company, and/or its affiliated entities, in the U.S. and/or other countries.
countries.

02.06 7795 Rev G Updated 07/2016 © 2016 Victaulic Company. All rights reserved.

victaulic.com 4