Scribd
Upload
110 views

Arduino Multimetro

1. This document provides a schematic and instructions for using an Arduino board to measure resistance and voltage. 2. It explains how to set the exact resistance and voltage reference values in the Arduino code for more accurate measurements. 3. Users are warned that the maximum input voltage is 30V and the maximum output voltage is 3.7V when using this circuit to measure voltage.

Uploaded by

Erisvaldo Vital DA Silva
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
110 views

Arduino Multimetro

1. This document provides a schematic and instructions for using an Arduino board to measure resistance and voltage. 2. It explains how to set the exact resistance and voltage reference values in the Arduino code for more accurate measurements. 3. Users are warned that the maximum input voltage is 30V and the maximum output voltage is 3.7V when using this circuit to measure voltage.

Uploaded by

Erisvaldo Vital DA Silva
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

1 2 3 4 5

Here testing (Ω , shortcut) Schematic for Oscilloscope Vin

5 5

6
For better accuracy set the exact value of resistance

6
Vout must never
Medir Omios Medir Omios and volt reference inside arduino code.For example you signal for testing
be higher 3.7v
have a resistance
of R6=100k but real value of this resistance may be 98.7k
A A
or 101.5k.The volt reference it's the same metod if you want
more accuracy you have to test with a voltmeter Arduino Vout = (R5/(R6+R5))*Vin R5 R1
13k 100k
pin "3.3v" and "5v" than set the exact value of this pins
inside arduino code. C1
So for more accuracy you need set in arduino code Warning! 0.1u

the exact values of resistance and volt reference pines "3.3v"


and "5v" In this case:
Switch(interruptor) Vin 30v MAX!!! to mini jack
U1

7 7
LCD nuelectronics Vout MAX 3.7v !!! Vout

8 8
R6
100k ARDUINO UNO
2 2 SCL
R7 NC SDA
B 10k B
1 1 IOREF AREF Bluetooth module (HC-05 9600 bitRate)
3 3 R8 RESET GND
220 3V SCK/PB5/13
U3
4 4 5V MISO/PB4/12 HC-05
GND2 MOSI/PWR/PB3/11
Sensor de temperatura (Temperature sensor) GND1 SS/PWR/PB2/10 6 EN
VIN PWR/PB1/9 5 VCC
PB0/8 4 GDN
U2 14/A0/PC0 3 TXD HC-05
TMP36 15/A1/PC1 PD7/7 2 RXD
16/A2/PC2 PWR/PD6/6 1 STATE
VCC 1
2 17/A3/PC3 PWR/PD5/5
VOUT
3 18/A4/PC4/SDA PD4/4
GND
19/A5/PC5/SCL INT1/PWR/PD3/3
INT0/PD2/2
TX/PD1/1
RX/PD0/0

C C

R1 R2
10k 100k

With this value of resistance MAX 40v!!!


D D

Medir Voltios (-) Medir Voltios (+)


TITLE:
Arduino Multimetr/Oscilloscope REV: 1.0
Here testing (Volts)
Date: 2017-12-11 Sheet: 1/1
EasyEDA V4.11.9 Drawn By: N.E.C.O
1 2 3 4 5

You might also like