Total Membrane

Surface Area
Solid-liquid separation carried out with Kubota SMU
(m2) (ft2) (mm) (ft) (mm) (ft) (mm) (ft) (kg) (lbs)
consistently achieves high quality effluent. This allows
permeate from Kubota SMU to be recycled/reused for toilet 8 86 1,300 4.27 512 1.68 150 0.49 50 110
flushing, irrigation, etc. 20 215 442 1.45 140 309
1,526 5.01 600 1.97
40 431 792 2.60 220 485
40 431 792 2.60 225 496
1,526 5.01 600 1.97
In the Conventional Activated Sludge 60 646 1,142 3.75 310 683
(CAS) system, effluent quality depends 60 646 1,142 3.75 330 728
Consistent effluent quality
on the condition of the final clarifier.
cannot be achieved. 80 861 1,492 4.90 430 948
Effluent quality is not stable.
Replacing a CAS system with a Kubota 600 1.97
MBR System can reduce effluent TSS 100 1,076 2,026 6.65 1,842 6.04 530 1,168
and allow for a higher Solids Retention 120 1,292 2,201 7.22 630 1,389
Time (SRT). 160 1,722 620 2.03 2,921 9.58 860 1,896
A lower effluent TSS concentration and
240 2,583 600 1.97 2,201 7.22 1,220 2,690
higher SRT can result in improved 3,506 11.50
Total Nitrogen (TN) removal and a 320 3,444 620 2.03 2,921 9.58 1,670 3,682
more stable operation. 218 2,347 2,251 7.39 1,070 2,359
2,490 8.17 575 1.89
290 3,122 2,925 9.60 1,365 3,009
435 4,682 2,251 7.39 2,070 4,564
4,290 14.07 575 1.89
580 6,243 2,925 9.60 2,635 5,809

Retrofitting an existing plant with a

Kubota MBR System can lead to
increased treatment capacity without
When factory outputs are
requiring new tanks. This is due to the
increased, existing wastewater
increased hydraulic capacity of the
treatment plants do not have
Kubota MBR System, which can be up
enough hydraulic capacity. to three times higher than that of the
CAS system. This results from a 3-fold
increase in sludge concentration
(12-18 g/L vs. 4-6 g/L). Moreover, a
final clarifier is not necessary with the
MBR process. Tanks that are no longer
required, such as aeration tanks and
clarifiers, can be re-used to house the
MBR system.

2016.7.eight

Permeated water from the Kubota KUBOTA Corporation KUBOTA Membrane Europe Ltd.
Membrane Systems Dept. 3rd Floor, No.1 Farrier's Yard, 77-85 Fulham Palace Road, London, W68JA, UK
SMU is highly treated, and coliforms
http://www.env.kubota.ne.jp/ksmu/ Phone:+44 （0） 20-8741-5262 Fax:+44 （0） 20-8563-1616
You can reuse the treated water are significantly removed.
http://www.kubota-mbr.com/
for irrigation, toilet flushing, or For Reverse Osmosis (RO) application,
Tokyo Head Office:1-3, Kyobashi 2-chome,
Kubota MBR permeated water requires KUBOTA Membrane USA Corporation
other reclaimed water applications. Chuo-ku, Tokyo, 104-8307 Japan
no further treatment before direct feed 11807 North Creek Parkway South, B-109, Bothell, WA 98011 USA
Phone:+81（0） 3-3245-3665 Fax:+81（0） 3-3245-3407
into the RO process. Phone:+1-425-898-2858 Fax:+1-425-898-2853
http://www.kubota-membrane.com/
 The footprint of the MBR system is considerably smaller than that of CAS system. The MBR system requires less
Every kind of wastewater has different characteristics and may require unique process design. With 30 The membrane unit consists of a membrane case (upper) and
aeration tank volume than a CAS system, and does not require a primary or secondary clarifier.
years of experience supported by MBR research and development as the flat-sheet membrane pioneer, a diffuser case (lower). The membrane case houses multiple
membrane cartridges that are connected to a manifold pipe via
Kubota is an expert in designing MBR systems to meet your specific requirements.
transparent tubes, while the diffuser case houses a coarse During normal aeration, the cleaning valve is closed, forcing
bubble diffuser. You can remove individual membrane air out of the diffuser. When the cleaning valve is opened, the
cartridges for easy maintenance work. diffuser system is flushed with a backflow of mixed liquor and
air. If an automated valve is installed, this operation can be
performed automatically.

The flat plate structure of the membrane cartridge presents Chemical cleaning of the KUBOTA Submerged Membrane Unit®
fewer obstacles to scouring flow than a hollow fiber membrane is done in-situ with chemicals such as sodium hypochlorite for
structure. Screening residues such as coarse solids and fibers organic fouling and oxalic acid for inorganic fouling. Since the
are less likely to be tangled within the KUBOTA Submerged membrane units do not need to be transferred to a separate
Membrane Unit®, which will reduce the need and frequency of chemical cleaning tank, the Kubota MBR System results in
The membrane sheet is welded on each side of the membrane panel. Treated water permeates through the membrane sheets
chemical cleaning. significant resource and labor-hour savings.
and spacers to exit the cartridge through the nozzle. Type 515 cartridge has two (2) nozzles. The placement of these nozzles
allows equal permeation across the membrane sheet’s surface, helping to prevent uneven fouling.

The membrane sheet is made from

chlorinated polyethylene and has a
maximum pore size of 0.4 μm (average:
0.2 μm).

Nozzle

Membrane Panel

Spacer
1,560mm

1,020mm
You can easily locate a damaged membrane cartridge by Since membrane cartridges can be individually removed, you
lowering the water level in the tank and visually checking the do not need to replace the entire membrane module or
individual transparent permeate tubes; there is no need to remaining functional cartridges.
Membrane Sheet drain the tank or inspect the entire membrane unit.

490mm
575mm

Type 510 cartridge Type 515 cartridge

(LF, FF, FS, ES, EK) (RM, RW)

Greater than 5,500 Installations All Over the World.