Dlk0459 - 0 Router Manual

Version 1.
0 | April 19, 2013
User Manual
Wireless AC1200
Dual Band Cloud Router
DIR-850L
Preface
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any
person or organization of such revisions or changes.
Manual Revisions
Revision Date Description
1.0 April 19, 2013 • Initial release for Revision A1
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United
States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of
their respective companies.
Copyright © 2013 by D-Link Systems, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission
from D-Link Systems, Inc.
D-Link DIR-850L User Manual i

Table of Contents
Table of Contents
Preface.................................................................................. i PPTP.....................................................................................31
Manual Revisions............................................................................ i L2TP.....................................................................................33
Trademarks....................................................................................... i DS-Lite................................................................................35
Internet Connection Setup Wizard........................................36
Product Overview............................................................... 1
Wireless Settings..................................................................41
Package Contents.......................................................................... 1
Wireless Connection Setup Wizard..........................42
System Requirements.................................................................. 2
Add Wireless Device with WPS Wizard....................44
Introduction.................................................................................... 3
Manual Wireless Settings.............................................46
Hardware Overview...................................................................... 4
802.11n/g (2.4GHz)...................................................46
Connections............................................................................ 4
802.11ac/n/a (5GHz)................................................47
LEDs............................................................................................ 5
Wireless Security..................................................................48
Installation.......................................................................... 6 What is WPA?....................................................................48
Before you Begin............................................................................ 6 WPA/WPA2-Personal (PSK)..........................................49
Wireless Installation Considerations....................................... 7 Configure WPA/WPA2-Enterprise (RADIUS)..........50
Connect to your Network........................................................... 8 Network Settings.................................................................52
Connect to an Existing Router................................................11 Router Settings................................................................52
DHCP Server Settings....................................................53
Configuration....................................................................13 DHCP Reservation..........................................................55
Quick Setup Wizard.....................................................................14 Storage....................................................................................56
QRS Mobile App...........................................................................21 Access Files from the Internet....................................57
SharePort Mobile App...............................................................22 IPv6...........................................................................................58
Web-based Configuration Utility...........................................26 IPv6 Internet Connection Setup Wizard.................60
Internet Connection Setup..............................................27 IPv6 Manual Setup.........................................................65
Static (assigned by ISP).................................................28 Auto Detection..........................................................65
Dynamic (Cable)..............................................................29 Static IPv6....................................................................66
PPPoE (DSL).......................................................................30 Autoconfiguration....................................................67
D-Link DIR-850L User Manual ii

Table of Contents
PPPoE............................................................................68 SysLog.................................................................................98
IPv6 in IPv4 Tunneling.............................................70 Email Settings..................................................................99
6 to 4 Tunneling.........................................................71 System............................................................................. 100
6rd..................................................................................72 Firmware......................................................................... 101
Local Connectivity....................................................73 Language Pack Upgrade........................................... 101
mydlink Settings..................................................................74 Dynamic DNS................................................................ 102
Advanced................................................................................75 System Check................................................................ 104
Virtual Server....................................................................75 Schedules....................................................................... 105
Port Forwarding..............................................................76 Status.................................................................................... 106
Application Rules............................................................77 Device Info..................................................................... 106
QoS Engine........................................................................78 Logs.................................................................................. 107
Network Filters.................................................................80 Statistics.......................................................................... 108
Access Control..................................................................81 Internet Sessions.......................................................... 109
Access Control Wizard.............................................81 Wireless........................................................................... 110
Website Filters..................................................................84 Routing............................................................................ 111
Inbound Filters.................................................................85 IPv6................................................................................... 112
Firewall Settings..............................................................86 IPV6 Routing.................................................................. 113
Routing...............................................................................88 Support................................................................................ 114
Advanced Wireless.........................................................89
Connect a Wireless Client to your Router.....................115
Wi-Fi Protected Setup (WPS)......................................90
WPS Button................................................................................. 115
WPS Button.................................................................91
Windows® 8................................................................................. 116
Advanced Network Settings.......................................92
Windows® 7................................................................................. 118
Guest Zone........................................................................93
WPA/WPA2.......................................................................... 118
IPv6 Firewall......................................................................94
WPS........................................................................................ 121
IPv6 Routing.....................................................................95
Windows Vista®.......................................................................... 125
Tools.........................................................................................96
WPA/WPA2.......................................................................... 126
Admin.................................................................................96
WPS/WCN 2.0..................................................................... 128
Time.....................................................................................97
D-Link DIR-850L User Manual iii

Table of Contents
Windows® XP.............................................................................. 129

WPA/WPA2.......................................................................... 130
Troubleshooting.............................................................132
Reset Router/Forgot Password............................................ 133
Wireless Basics................................................................136
What is Wireless?....................................................................... 137
Tips................................................................................................. 139
Wireless Modes.......................................................................... 140
Networking Basics..........................................................141
Check your IP address............................................................. 141
Windows® 8 Users............................................................. 141
Windows® 7/Vista® Users............................................... 141
Windows® XP Users.......................................................... 141
Statically Assign an IP Address............................................ 142
Windows® 8 Users............................................................. 142
Windows® 7/ Vista® Users............................................... 143
Windows® XP Users.......................................................... 144
Technical Specifications.................................................145
Contacting Technical Support.......................................151
GPL Code Statement......................................................152
Warranty..........................................................................164
Registration....................................................................171
D-Link DIR-850L User Manual iv

Section 1 - Product Overview
Product
PackageOverview
Contents
DIR-850L Wireless AC1200 Dual Band Cloud Router
Power Adapter
Ethernet Cable
Wi-Fi Configuration Card
Quick Install Guide
If any of the above items are missing, please contact your reseller.
Note: Using a power supply with a different voltage rating than the one included with the DIR-850L will cause damage and void the warranty
for this product.
D-Link DIR-850L User Manual 1

System Requirements
Network Requirements • An Ethernet-based broadband modem
Computer with the following:

• Windows®, Macintosh, or Linux-based operating system
• An installed Ethernet adapter or wireless adapter
Supported Browsers:
Web-based Configuration • Internet Explorer 7 or higher
Utility Requirements • Firefox
• Safari 4 or higher
• Chrome
Windows® Users: Make sure you have the latest version of Java
installed. Visit www.java.com to download the latest version.
• iPhone/iPad/iPod Touch (iOS 3.0 or higher)

• Android device (1.6 or higher)
• Computer with the following browser requirements:
• Internet Explorer 7 or higher
mydlink Requirements • Firefox
• Safari 5 or higher
• Chrome
iPhone, iPad, and iPod touch are registered trademarks of Apple Inc. Android is a trademark of Google, Inc.

Introduction
The D-Link® DIR-850L Wireless AC1200 Dual Band Cloud Router provides revolutionary Gigabit 802.11ac wireless speed - up
to 1200Mbps – for flawless HD video streaming to multiple devices.
With ground-breaking mydlink Cloud Services, you can monitor your home network from anywhere on your iPhone, iPad,
and Android device. See websites that are being visited, block unwanted devices and receive automatic email alerts when
unauthorized connections are attempted.
With SharePort Mobile, wirelessly access your media on your iPhone, iPad or Android device from any connected USB drive.
Best of all, the apps for network management and file access are free.
* Maximum wireless signal rate derived from IEEE Standard 802.11ac (draft), 802.11a, 802.11g, and 802.11n specifications. Actual data throughput will vary. Network conditions
and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely affect wireless signal range.

Hardware Overview
Connections
1
2
4
5
6 7
1 USB Port Connect a USB flash drive to share content throughout your network.
2 WPS Button Press to start the WPS process. The Power LED will blink during this process.
3 LAN Ports (1-4) Connect 10/100/1000 Ethernet devices such as computers, switches, storage (NAS) devices, and game consoles.
4 Internet Port Using an Ethernet cable, connect your broadband modem to this port.
5 Power Button Press the power button to power on and off.
6 Power Receptor Receptor for the supplied power adapter.
7 Reset Button Press and hold until the Power LED turns orange to reset the device back to the default factory settings.

Hardware Overview
LEDs
1
2
A solid green light indicates a proper connection to the power supply. The light will be solid orange during boot-up
1 Power LED
and will blink green during the WPS process.
A solid light indicates a connection to the Internet port. If the LED is orange, the connection is good but the router
2 Internet LED cannot connect to the Internet. If this LED is blinking orange, this indicates that the “on demand” connection
type is set and the Internet connection is idle.

Section 2 - Installation
Installation
This section will walk you through the installation process. Placement of the router is very important. Do not place the router
in an enclosed area such as a closet, cabinet, or in the attic or garage.
Before you Begin

• Please configure the router with the computer that was last connected directly to your modem.
• Users with DSL providers - If you are using a PPPoE connection, you will need your PPPoE user name and password.
If you do not have this information, contact your Internet provider. Do not proceed until you have this information.
• Users with Cable providers - Make sure you unplug the power to your modem. In some cases, you may need to turn
it off for up to 5 minutes.
• Advanced Users - If your ISP provided you with a modem/router combo, you will need to set it to “bridge” mode so
the DIR-850L router can work properly. Please contact your ISP or refer to the user manual for your modem/router
device.

Wireless Installation Considerations

The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the
operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings,
or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types
of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to
follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum -
each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that
the number of walls or ceilings is minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle
appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position
devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.
3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on range.
Try to position access points, wireless routers, and computers so that the signal passes through drywall or open
doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file
cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF
noise.
5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security
systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone
base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not
in use.

Connect to your Network

1. Turn off and unplug your DSL or Cable modem. This is required.
Modem
2. Connect an Ethernet cable from the Internet port of the router to the Ethernet port on your DSL or Cable modem.
Ethernet Cable
Ethernet Port
USB
WPS
LAN
INTERNET
Internet Port (yellow)
POWER
12V 2A
Modem
DIR-850L

3. Connect another Ethernet cable from the Ethernet port on your computer to one of the LAN ports on the router.
USB
WPS
LAN
INTERNET Ethernet Cable Computer

POWER
12V 2A
DIR-850L
4. Plug the power back into your DSL or Cable modem. Please wait about one minute before continuing.
USB
Computer
WPS
LAN
INTERNET
POWER
12V 2A
Modem
DIR-850L

5. Plug the power adapter into your router and connect to an available power outlet or surge protector. If the
Power LED does not light up, press the Power button on the back of the router.
WPS
USB
Computer
1
LAN
INTERNET
POWER
Power Button
12V 2A
Modem
DIR-850L
6. After the router has powered up, verify that the power (green) and Internet (orange or green) LEDs are both lit.
Please skip to page 13 to configure your router and use the manual setup procedure to configure your network
and wireless settings. If you did not connect to the Internet, use the D-Link Setup Wizard (refer to page 14).

Connect to an Existing Router

Note: It is strongly recommended to replace your existing router with the DIR-850L instead of using both. If your modem is a combo
router, you may want to contact your ISP or manufacturer’s user guide to put the router into Bridge mode, which will ‘turn off’ the
router (NAT) functions.
If you are connecting the DIR-850L router to an existing router to use as a wireless access point and/or switch, you will have
to do the following to the DIR-850L before connecting it to your network:
• Disable UPnP™
• Disable DHCP
• Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept
a DHCP address from your other router.
To connect to another router, please follow the steps below:
1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable. Make sure
your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the Networking Basics
section for more information. If you need to change the settings, write down your existing settings before making any
changes. In most cases, your computer should be set to receive an IP address automatically in which case you will not have
to do anything to your computer.
2. Open a web browser, enter http://192.168.0.1 (or http://dlinkrouter.local./) and press Enter. When the login window
appears, set the user name to Admin and leave the password box empty. Click Log In to continue.
3. Click on Advanced and then click Advanced Network. Uncheck the Enable UPnP checkbox. Click Save Settings to continue.
4. Click Setup and then click Network Settings. Uncheck the Enable DHCP Server checkbox. Click Save Settings to continue.

5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings to save your
settings. Use this new IP address to access the configuration utility of the router in the future. Close the browser and change
your computer’s IP settings back to the original values as in Step 1.
6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.
7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything
into the Internet (WAN) port of the D-Link router.
8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers. To configure your wireless network,
open a web browser and enter the IP address you assigned to the router. Refer to the Configuration and Wireless Security
sections for more information on setting up your wireless network.

Configuration
There are several different ways you can configure your router to connect to the Internet and connect to your clients:
• QRS Mobile App - Use your iPhone, iPad, or Android device to configure your router. Refer to page 21
• D-Link Setup Wizard - This wizard will launch when you log into the router for the first time. Refer to page 14.
• Manual Setup - Log into the router and manually configure your router (advanced users only). Refer to page 27.

Section 3 - Configuration
Quick Setup Wizard

If this is your first time installing the router, launch your web
browser (e.g., Internet Explorer), and you will automatically be
directed to the Wizard Setup Screen.
If you have already configured your settings and you would like
to access the configuration utility, please refer to page 26.
If this is your first time logging into the router, this wizard will
start automatically.
This wizard is designed to guide you through a step-by-step

process to configure your new D-Link router and connect to the
Internet.
Click Next to continue.
Please wait while your router detects your internet connection type. If
the router detects your Internet connection, you may need to enter your
ISP information such as username and password (PPPoE).

If the router does not detect a valid Ethernet connection from the
Internet port, this screen will appear. Connect your broadband modem
to the Internet port and then click Next.
If the router detects an Ethernet connection but does not detect the type
of Internet connection you have, this screen will appear. Click Guide me
through the Internet Connection Settings to display a list of connection
types to choose from.
Select your Internet connection type. You can select DHCP Connection
(Dynamic IP Address) if your Internet connection automatically
provides you with an IP Address. This option is commonly used for cable
modem services. Click Next to continue.

If the router detected or you selected PPPoE, enter your PPPoE username
and password and click Next to continue.
Note: Make sure to remove your PPPoE software from your computer. The
software is no longer needed and will not work through a router.
If the router detected or you selected PPTP, enter your PPTP username,
password, and other information supplied by your ISP. Click Next to
continue.
If the router detected or you selected L2TP, enter your L2TP username,
password, and other information supplied by your ISP. Click Next to
continue.

If the router detected or you selected Static, enter the IP and DNS
settings supplied by your ISP. Click Next to continue.
For both the 2.4GHz and 5GHz segments, create a wireless network
name (SSID) using up to 32 characters.
Create a wireless security passphrase or key (between 8-63 characters).

Your wireless clients will need to have this passphrase or key entered
to be able to connect to your wireless network.
In order to secure your router, please enter a new password. Check

the Enable Graphical Authentication box to enable CAPTCHA
authentication for added security. Click Next to continue.

Select your time zone from the drop-down menu and click Next to
continue.
The Confirm Wi-Fi Settings window will display your wireless settings.
Click Save to continue.
If you want to create a bookmark to the router, click OK. Click Cancel if
you do not want to create a bookmark.
If you clicked Yes, a window may appear (depending on what web

browser you are using) to create a bookmark.

To use the mydlink service (mydlink.com or the mydlink Lite app), you
must have an account. Select if you do have a mydlink account or if you
need to create one. Click Next to continue.
If you do not want to register at this time, click Cancel.
If you clicked Yes, I have a mydlink account enter your mydlink account
name (E-mail address) and password. Click Login to register your router.
If you clicked No, I want to register and login with a new mydlink
account fill out the requested information and click Next to create your
mydlink account. This is a free service. Refer to www.mydlink.com for
more information.

The mydlink App will allow you to receive notices, browse network
users, and configure your router from an iPhone/iPad/iPod Touch
(iOS 3.0 or higher), or Android device (1.6 or higher).
To download the "mydlink lite" app, visit the Apple Store, Google
Play or http://mydlink.com/Lite.
PC and Mac users can use the mydlink portal at http://mydlink.com.

QRS Mobile App

D-Link offers an app for your iPad, iPhone (iOS 4.3 or higher) or Android device to install and configure your router.
Step 1
From your iOS device, go to App Store, or from your Android
device, go to Google Play and search for ‘D-Link’. Select QRS
Mobile and then download it.
You may also scan this code to download.
iOS Android
Step 2
Once your app is installed, you may now configure your router. Wi-Fi Name(SSID) 2.4Ghz:
Connect to the router wirelessly by going to your wireless utility

dlink-2c19
Wi-Fi Name(SSID) 5GHz:
dlink-2C1B-media
on your device. Scan for the wireless network name (SSID) as

Password:gccnu80856
listed on the supplied info card. Select and then enter your
security password (Wi-Fi Password).
Step 3
Once you connect to the router, launch the QRS mobile app and
it will guide you through the installation of your router.

SharePort Mobile App

The SharePort Mobile app will allow you to access files from a USB thumb drive that is plugged into your router. You must enable file sharing from
the Setup > Storage page (refer to page 51) for this app to work properly.
1. Insert your USB flash drive into DIR-850L.
2. Scan the bar code to download the SharePort Mobile app from the app
store to your iPhone, iPad, or Android device.
iOS Android
3. From your iOS mobile device, click Settings.
Settings

4. Click Wi-Fi, select the wireless network (SSID) that you created in the
setup and then enter your Wi-Fi password.
5. Once connected, click on the SharePort Mobile icon.
6. The following screen will appear.

7. Click on Settings icon located on the right top corner of the screen. Click
Edit to enter your User Name and Password. Once you finish, click Done
to continue.
8. For the Movie section, click the movie icon to play your movie from your
USB flash drive.
9. For the Music section, click the music icon to play your music from your
USB flash drive.

10. For the Photo section, click the photo icon to view your photos from
your USB flash drive.
11. For the Files section, click on the files icon to view your files from your
USB flash drive.
12. For the Folder section, click the folder icon to view your folders
from your USB flash drive.

Web-based Configuration Utility

Open a web browser (e.g., Internet Explorer, Chrome, Firefox , or Safari)
and enter http://dlinkrouter.local./ or http://192.168.0.1.
Enter your password and click Login.
Note: If you did not create a password with the Setup Wizard,
leave the password blank by default.

Internet Connection Setup

If you want to configure your router to connect to the Internet using
the wizard, click Internet Connection Setup Wizard. Refer to page 36.
If you consider yourself an advanced user, click Manual Internet

Connection Setup to configure your connection manually.
(Instructions for manual setup begin below.)
The next few pages will explain each of the ISP connection types. You
can select the type from the My Internet Connection is drop-down
menu.

Manual Internet Setup

Static (assigned by ISP)
Select Static IP if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway
address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four
octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
My Internet Connection: Select Static IP to manually enter the IP settings supplied by

your ISP.
IP Address: Enter the IP address assigned by your ISP.
Subnet Mask: Enter the Subnet Mask assigned by your ISP.
Default Gateway: Enter the Gateway assigned by your ISP.
DNS Servers: The DNS server information will be supplied by your ISP
(Internet Service Provider.)
MTU: Maximum Transmission Unit - you may need to change the

MTU for optimal performance with your specific ISP. 1500 is
the default MTU.
MAC Address: The default MAC Address is set to the Internet port’s physical
interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless
required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with
the MAC address of your Ethernet card.

Internet Setup
Dynamic (Cable)
My Internet Select Dynamic IP (DHCP) to obtain IP Address information
Connection: automatically from your ISP. Select this option if your ISP does not
give you any IP numbers to use. This option is commonly used for
cable modem services.
Host Name: The Host Name is optional but may be required by some ISPs. Leave
blank if you are not sure.
Use Unicasting: Check the box if you are having problems obtaining an IP address
from your ISP.
Primary/Secondary Enter the Primary and secondary DNS server IP addresses assigned
DNS Server: by your ISP. These addresses are usually obtained automatically
from your ISP. Leave blank if you did not specifically receive these
from your ISP.
MTU: Maximum Transmission Unit - you may need to change the MTU
for optimal performance with your specific ISP. 1500 is the default MTU.
MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.

Internet Setup
PPPoE (DSL)
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a
username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your
computer. The software is no longer needed and will not work through a router.
My Internet Select PPPoE (Username/Password) from the drop-down menu.
Connection:
Address Mode: Select Static IP if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic.
IP Address: Enter the IP address (Static PPPoE only).
User Name: Enter your PPPoE user name.
Password: Enter your PPPoE password and then retype the password in the next box.
Service Name: Enter the ISP Service Name (optional).
Reconnect Select either Always-on, On-Demand, or Manual.

Mode:
Maximum Idle Enter a maximum idle time during which the Internet connection
Time: is maintained during inactivity. To disable this feature, enable Auto-
reconnect.
DNS Mode: Select Receive DNS from ISP to automatically use your ISP’s DNS servers
or select Enter DNS Manually and enter the Primary and Secondary DNS Server Addresses of your choice.
MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the default MTU.

Internet Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services.
My Internet Select PPTP (Username/Password) from the drop-down menu.

Connection:
Address Mode: Select Static if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic.
PPTP IP Address: Enter the IP address (Static PPTP only).
PPTP Subnet Enter the Primary and Secondary DNS Server Addresses (Static PPTP
Mask: only).
PPTP Gateway IP Enter the Gateway IP Address provided by your ISP.

Address:
PPTP Server IP Enter the Server IP provided by your ISP (optional).

Address:
Username: Enter your PPTP username.
Password: Enter your PPTP password and then retype the password in the next
box.

Mode:
Maximum Idle Enter a maximum idle time during which the Internet connection is
Time: maintained during inactivity. To disable this feature, enable Auto-reconnect.

DNS Servers: The DNS server information will be supplied by your ISP (Internet Service Provider.)
MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default
MTU.

Internet Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and
password. This option is typically used for DSL services.
My Internet Select L2TP (Username/Password) from the drop-down menu.

Connection:
Address Mode: Select Static if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases, select
Dynamic.
L2TP IP Address: Enter the L2TP IP address supplied by your ISP (Static only).
L2TP Subnet Enter the Subnet Mask supplied by your ISP (Static only).
Mask:
L2TP Gateway IP Enter the Gateway IP Address provided by your ISP.

Address:
L2TP Server IP Enter the Server IP provided by your ISP (optional).

Address:
Username: Enter your L2TP username.
Password: Enter your L2TP password and then retype the password in
the next box.

Mode:
Maximum Idle Enter a maximum idle time during which the Internet
Time: connection is maintained during inactivity. To disable this feature,
enable Auto-reconnect.

DNS Servers: Enter the Primary and Secondary DNS Server Addresses (Static L2TP only).
MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default
MTU.

Internet Setup
DS-Lite
DS-Lite is an IPv6 connection type. After selecting DS-Lite, the following parameters will be available for configuration:
My Internet Select DS-Lite from the drop-down menu.

Connection is:
DS-Lite Select the DS-Lite DHCPv6 Option to let the router allocate
Configuration: the AFTR IPv6 address automatically. Select the Manual
Configuration option to enter the AFTR IPv6 address in
manually.
AFTR IPv6 After selecting the Manual Configuration option above,

Address: enter the AFTR IPv6 address used here.
B4 IPv4 Address: Enter the B4 IPv4 address value used here (optional).
WAN IPv6 Once connected, the WAN IPv6 address will be displayed here.
Address:
IPv6 WAN Once connected, the IPv6 WAN Default Gateway address will
Default Gateway be displayed here.

Internet Connection Setup Wizard

If you did not initially choose to install your router with the
Quick Setup Wizard, you can click on Internet Connection
Setup Wizard from the Setup > Internet screen.
This wizard is designed to guide you through a step-by-step

process to configure your new D-Link router and connect to
the Internet.

In order to secure your router, enter a new password. Click Next

to continue.
Select your time zone from the drop-down menu and click Next
to continue.
Select your Internet connection type. You can select DHCP

Connection (Dynamic IP Address) if your Internet connection
automatically provides you with an IP Address. This option is
commonly used for cable modem services. Click Next to continue.

If you selected DHCP Connection (Dynamic IP Address) you can

click on Clone Your PC’s MAC Address to copy your computer’s
MAC address to your router. Click Next to continue.
If you selected PPPoE, enter your PPPoE username and password

and click Next to continue.
Note: Make sure to remove your PPPoE software from your computer.
The software is no longer needed and will not work through a router.

If you selected PPTP, enter your PPTP username, password, and

other information supplied by your ISP. Click Next to continue.
If you selected L2TP, enter your L2TP username, password, and

other information supplied by your ISP. Click Next to continue.

If you selected Static, enter the IP and DNS settings supplied by

your ISP. Click Next to continue.
When the setup process is completed, you will see this screen.
Click on Connect to save your settings.

Wireless Settings
If you want to configure the wireless settings on your router using
the wizard, click Wireless Connection Setup Wizard and refer to
the next page.
Click Add Wireless Device with WPS if you want to add a wireless
device using Wi-Fi Protected Setup (WPS) and refer to page 44.
If you want to manually configure the wireless settings on your

router click Manual Wireless Connection Setup and refer to
page 46.

Section 4 - Security
Wireless Connection Setup Wizard
To run the security wizard, click on Setup > Wireless Settings. Click
on the Wireless Connection Setup Wizard button.
Enter a name for your wireless network (SSID), one for the 2.4GHz
frequency and another for the 5GHz frequency. Do not use personal
information as your SSID since users with wireless devices within
range of your router will be able to see this information.
Then select one of the following options:
Automatically: Select this option to automatically generate

the router’s network key and click Next.
Manually: Select this option to manually enter your network

key and click Next.
If you selected Automatically, the summary window will display

your settings. Write down the security key and enter this on your
wireless clients. Click Save to save your settings.
If you selected Manually, the following screen will appear.
Create a passphrase for your Wireless Security Password. Click

Next to continue.
Note: The security password/passphrase must be between 8 and 63

characters and is case-sensitive. You will need to enter this passphrase
on your wireless clients exactly or it will not connect.

Add Wireless Device with WPS Wizard
From the Setup > Wireless Settings screen, click Add Wireless
Device with WPS.
Select Auto to add a wireless client using WPS (Wi-Fi Protected

Setup) and then click Next. Skip to the next page.
If you select Manual, a settings summary screen will appear. Write

down the security key and enter this on your wireless clients. Click
Wireless Status to finish. This will take you to the Wireless Status
screen.

PIN: Select this option to use PIN method. In order to use this
method you must know the wireless client’s 8 digit PIN and click
Connect.
PBC: Select this option to use PBC (Push Button) method to add a
wireless client. Click Connect.
Once you click Connect, you will have a 120 second time limit to
apply the settings to your wireless client(s) and successfully establish
a connection.
Click Wireless Status to finish. This will take you to Wireless Status
screen.

Manual Wireless Settings

802.11n/g (2.4GHz)
Enable Wireless: Check the box to enable the wireless function. If you do not want to use
wireless, uncheck the box to disable all the wireless functions.
Schedule: Select the time frame that you would like your wireless network enabled.
The schedule may be set to Always. Any schedule you create will be
available in the drop-down menu. Click New Schedule to create a
schedule.
Wireless Network Service Set Identifier (SSID) is the name of your wireless network. Create
Name: a name for your wireless network using up to 32 characters. The SSID is
case-sensitive.
802.11 Mode: Select one of the following:

802.11b Only - Select only if all of your wireless clients are 802.11b.
802.11g Only - Select only if all of your wireless clients are 802.11g.
802.11n Only - Select only if all of your wireless clients are 802.11n.
Mixed 802.11g and 802.11b - Select if you are using both 802.11g and
802.11b wireless clients.
Mixed 802.11n and 802.11g - Select if you are using both 802.11n and 802.11g wireless clients.
Mixed 802.11n, 11g, and 11b - Select if you are using a mix of 802.11n, 802.11g, and 802.11b wireless clients.
Enable Auto Channel The Auto Channel Scan setting can be selected to allow the DIR-850L to choose the channel with the least amount of interference.
Scan:
Wireless Channel: Indicates the channel setting for the DIR-850L. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the
wireless network. If you check Enable Auto Channel Scan, this option will be greyed out.
Channel Width: Select the Channel Width:

20/40MHz(Auto) - This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices.
20MHz - Select if you are not using any 802.11n wireless clients.
Visibility Status: Select Invisible if you do not want the SSID of your wireless network to be broadcasted by the DIR-850L. If Invisible is selected, the SSID of the DIR-850L will
not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-850L in order to connect to it.
Wireless Security: Refer to page 48 for more information regarding wireless security.

802.11ac/n/a (5GHz)
Enable Wireless: Check the box to enable the wireless function. If you do not want to
use wireless, uncheck the box to disable all the wireless functions.
Schedule: Select the time frame that you would like your wireless network
enabled. The schedule may be set to Always. Any schedule you
create will be available in the drop-down menu. Click New Schedule
to create a schedule.
Wireless Network Service Set Identifier (SSID) is the name of your wireless network.
Name: Create a name for your wireless network using up to 32 characters.
The SSID is case-sensitive.
802.11 Mode: Select one of the following:

802.11a Only - Select if all of your wireless clients are 802.11a.
802.11n Only - Select only if all of your wireless clients are 802.11n.
Mixed 802.11a and 802.11n - Select if you are using both 802.11n
and 802.11a wireless clients.
Mixed 802.11ac - Select if you are using 802.11ac, 802.11n and
802.11a wireless clients.
Enable Auto Channel The Auto Channel Scan setting can be selected to allow the DIR-850L to choose the channel with the least amount of interference.
Scan:
Wireless Channel: Indicates the channel setting for the DIR-850L. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the
wireless network. If you check Enable Auto Channel Scan, this option will be greyed out.
Channel Width: Select the Channel Width:

20MHz - Select if you are not using any 802.11n wireless clients.
20/40MHz(Auto) - This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices.
20/40/80MHz(Auto) - Select if you are using 802.11ac, 802.11n and non-802.11n wireless devices. This option is only available when the 802.11 Mode is set
to Mixed 802.11ac.
Visibility Status: Select Invisible if you do not want the SSID of your wireless network to be broadcasted by the DIR-850L. If Invisible is selected, the SSID of the DIR-850L will
not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-850L in order to connect to it.
Wireless Security: Refer to page 48 for more information regarding wireless security.

Wireless Security
This section will show you the different levels of security you can use to protect your data from intruders. The DIR-850L offers the
following types of security:
• WPA2 (Wi-Fi Protected Access 2) • WPA2-PSK (Pre-Shared Key)

• WPA (Wi-Fi Protected Access) • WPA-PSK (Pre-Shared Key)
What is WPA?
WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
The 2 major improvements over WEP:
• Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing
algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is
based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.
• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP
regulates access to a wireless network based on a computer’s hardware-specific MAC address, which is relatively simple
to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized
network users can access the network.
WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between
8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your
wireless router or access point.
WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public
key encryption system to ensure that only authorized network users can access the network.

WPA/WPA2-Personal (PSK)
It is recommended to enable wireless security on your wireless router before your wireless network adapters. Please establish
wireless connectivity before enabling encryption.
1. Log into the web-based configuration by opening a web browser and

entering the IP address of the router (192.168.0.1). Click on Setup and
then click Wireless Settings on the left side.
2. Next to Security Mode, select WPA-Personal.
3. Next to WPA Mode, select Auto(WPA or WPA2), WPA2 Only, or WPA

Only. Use Auto if you have wireless clients using both WPA and WPA2.
4. Next to Cypher Type, select TKIP and AES, TKIP, or AES.
5. Next to Group Key Update Interval, enter the amount of time before
the group key used for broadcast and multicast data is changed (3600
is default).
6. Next to Pre-Shared Key, enter a key (passphrase). The key is entered as

a pass-phrase in ASCII format at both ends of the wireless connection. The pass-phrase must be between 8-63 characters.
7. Click Save Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity
until you enable WPA-PSK on your adapter and enter the same passphrase as you did on the router.

Configure WPA/WPA2-Enterprise (RADIUS)
It is recommended to enable wireless security on your wireless router before your wireless network adapters. Please establish
wireless connectivity before enabling encryption.
1. Log into the web-based configuration by opening a web browser and

entering the IP address of the router (192.168.0.1). Click on Setup
and then click Wireless Settings on the left side.
2. Next to Security Mode, select WPA-Enterprise.
3. Next to WPA Mode, select Auto(WPA or WPA2), WPA2 Only, or WPA

Only. Use Auto if you have wireless clients using both WPA and
WPA2.
4. Next to Cypher Type, select TKIP and AES, TKIP, or AES.
5. Next to Group Key Update Interval, enter the amount of time before
the group key used for broadcast and multicast data is changed
(3600 is default).
6. Next to RADIUS Server IP Address enter the IP Address of your RADIUS

server.

7. Next to RADIUS Server Port, enter the port you are using with
your RADIUS server. 1812 is the default port.
8. Next to RADIUS Server Shared Secret, enter the security key.
9. Click Advanced to enter settings for a secondary RADIUS Server.
10. Click Save Settings to save your settings.

Network Settings
This section will allow you to change the local network settings of the router and to configure the DHCP settings.
Router Settings
Router IP Address: Enter the IP address of the router. The default IP address
is 192.168.0.1.
If you change the IP address, once you click Save Settings,

you will need to enter the new IP address in your browser
to get back into the configuration utility.
Default Subnet Enter the Subnet Mask. The default subnet mask is
Mask: 255.255.255.0.
Host Name: Enter a name for the router.
Local Domain Enter the Domain name (Optional).

Name:
Enable DNS Relay: Uncheck the box to transfer the DNS server information
from your ISP to your computers. If checked, your
computers will use the router for a DNS server.

DHCP Server Settings

DHCP stands for Dynamic Host Control Protocol. The DIR-850L has a built-in DHCP server. The DHCP Server will automatically
assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting
their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load
the proper TCP/IP settings provided by the DIR-850L. The DHCP Server will automatically allocate an unused IP address from
the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.
Enable DHCP Check this box to enable the DHCP server on your router.
Server: Uncheck to disable this function.
DHCP IP Address Enter the starting and ending IP addresses for the DHCP
Range: server’s IP assignment.
Note: If you statically (manually) assign IP addresses to your

computers or devices, make sure the IP addresses are outside of
this range or you may have an IP conflict.
DHCP Lease Time: The length of time for the IP address lease. Enter the Lease
time in minutes.
Always Enable this feature to broadcast your DHCP server to LAN/

Broadcast: WLAN clients.
NetBIOS NetBIOS allows LAN hosts to discover all other computers

Announcement: within the network, enable this feature to allow the DHCP
Server to offer NetBIOS configuration settings.
Learn NetBIOS Enable this feature to allow WINS information to be learned from the WAN side; disable to allow manual configuration.
from WAN:
NetBIOS Scope: This feature allows the configuration of a NetBIOS ‘domain’ name under which network hosts operates. This setting has no effect if
the ‘Learn NetBIOS information from WAN’ is activated.

NetBIOS Node Select the different type of NetBIOS node; Broadcast only, Point-to-Point, Mixed-mode, and Hybrid.
Type:
WINS IP Enter your WINS Server IP address(es).

Address:

DHCP Reservation
If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP
address only to that computer or device.
Note: This IP address must be within the DHCP IP Address Range.
Enable: Check this box to enable the reservation.
Computer Name: Enter the computer name or select from the drop-down
menu and click <<.
IP Address: Enter the IP address you want to assign to the computer

or device. This IP Address must be within the DHCP IP
Address Range.
MAC Address: Enter the MAC address of the computer or device.
Clone Your PC’s You can use the Clone Your PC’s MAC Address button
MAC Address: to replace the Internet port’s MAC address with the MAC
address of your Ethernet card.
Save: Click Save to save your entry. You must click Save Settings
at the top to activate your reservations.
DHCP Reservations List
DHCP Displays any reservation entries. Displays the host name
Reservations List: (name of your computer or device), MAC Address, and IP
address.
Enable: Check to enable the reservation.
Edit: Click the edit icon to make changes to the reservation entry.
Delete: Click to remove the reservation from the list.

Storage
This page will allow you to access files from a USB external hard drive or thumb drive that is plugged into the router from your
local network or from the Internet using either a web browser or an app for your smartphone or tablet. You can create users
to be allowed to access these files.
Enable SharePort Check to enable sharing files on your USB storage device
Web Access: that is plugged in your router.
HTTP Access Port: Enter a port (8181 is default). You will have to enter this port
in the URL when connecting to the shared files. For example:
(http://192.168.0.1:8181).
HTTPS Access Enter a port (4433 is default). You will have to enter this port
Port: in the URL when connecting to the shared files. For example:
(https://192.168.0.1:4433).
Allow Remote Check this option the allow remote access to this router.
Access:
User Name: To create a new user, enter a user name.
Password: Enter a password for this account.
Verify Password: Re-enter the password. Click Add/Edit to create the user.
User List: Displays the accounts. The Admin and Guest accounts are
built-in to the router.
Number of Displays the USB device plugged into the router.

Devices:

Access Files from the Internet

Below are step-by-step instructions on how to access files that are on your USB thumb drive or external hard drive that is connected to your router:
Step 1 - Enable SharePort Web Access

Check the Enable SharePort Web Access checkbox to enable. Then
select if you want to use HTTP or HTTPS (secure) and enter the port(s)
you want to use. The default for HTTP is 8181 and HTTPS is 4433.
Step 2 - Create a User Account

Under User Creation, enter a username and password, and then click
Add/Edit.
Step 3 - Configure your Access Path

Under User List, click the Modify icon for the user you just created.
Here you can browse to the folder on your USB storage device you
want to assign the Access Path to.
Step 4 - Save Settings

If you want to add more users, repeat steps 2 and 3. Once you are
finished, click the Save Settings button at the top to save your
settings.
Note that under the HTTP Storage Link (at the bottom) will display
the URL(s) you can use to connect. Also if you selected HTTPS, you
must type in HTTPS:// instead of HTTP:// to get a secure connection.
For example, if you selected HTTPS and changed the port to

3200, and your WAN IP address is 1.2.3.4, then you would enter
HTTPS://1.2.3.4:3200 to connect.

IPv6
On this page, the user can configure the IPv6 Connection type. There are three ways to set up the IPv6 Internet connection.
For the beginner user that has not configured a router before, click on
the IPv6 Internet Connection Setup Wizard button and the router will
guide you through a few simple steps to get your network up and running.
(Refer to page 60.)
For the advanced user that has configured a router before, click on the
Manual IPv6 Internet Connection Setup button to input all the settings
manually. (Refer to page 65.)
If you would like to manually configure the IPv6 local connectivity settings
of your router, click on IPv6 Local Connectivity Settings.

Click on Enable ULA. You can check Use default ULA prefix, or you
can leave the box unchecked and enter the prefix manually in the
ULA Prefix text box.

IPv6 Internet Connection Setup Wizard

On this page, the user can configure the IPv6 Connection type using the IPv6 Internet Connection Setup Wizard.
Click the IPv6 Internet Connection Setup Wizard button and the router will guide
you through a few simple steps to get your network up and running.
Click Next to continue to the next page. Click Cancel to discard the changes made
and return to the main page.
The router will try to detect whether its possible to obtain the IPv6 Internet
connection type automatically. If this succeeds then the user will be guided through
the input of the appropriate parameters for the connection type found.

However, if the automatic detection fails, the user will be prompt to either Try
again or to click on the Guide me through the IPv6 settings button to initiate the
manual continual of the wizard.
There are several connection types to choose from. If you are unsure of your
connection method, please contact your IPv6 Internet Service Provider.
Note: If using the PPPoE option, you will need to ensure that any PPPoE client
software on your computers has been removed or disabled. The three options
available on this page are IPv6 over PPPoE, Static IPv6 address and Route, and
Tunneling Connection (6rd).
Choose the required IPv6 Internet Connection type and click on the Next button
to continue. Click on the Prev button to return to the previous page. Click on the
Cancel button to discard all the changes made and return to the main page.

IPv6 over PPPoE

After selecting the IPv6 over PPPoE option, the user will be able to configure the
IPv6 Internet connection that requires a username and password to get online.
Most DSL modems use this type of connection.
The following parameters will be available for configuration:
PPPoE Session: Select the PPPoE Session value used here. This
option will state that this connection shares it’s
information with the already configured IPv6
PPPoE connection, or the user can create a new
PPPoE connection here.
User Name: Enter the PPPoE username used here. If you do not
know your user name, please contact your ISP.
Password: Enter the PPPoE password used here. If you do not
know your password, please contact your ISP.
Verify Password: Re-enter the PPPoE password used here.
Service Name: Enter the service name for this connection here.
This option is optional.

Static IPv6 Address Connection

This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your
IPv6 configuration settings. You must enter the IPv6 address, Subnet Prefix Length, Default Gateway, Primary DNS Server, and Secondary DNS
Server. Your ISP provides you with all this information.
Use Link-Local The Link-local address is used by nodes and routers when
Address: communicating with neighboring nodes on the same link.
This mode enables IPv6-capable devices to communicate
with each other on the LAN side.
IPv6 Address: Enter the WAN IPv6 address for the router here.
Subnet Prefix Enter the WAN subnet prefix length value used here.
Length:
Default Gateway: Enter the WAN default gateway IPv6 address used here.
Primary DNS Enter the WAN primary DNS Server address used here.
Address:
Secondary DNS Enter the WAN secondary DNS Server address used here.
Address:
LAN IPv6 Address: These are the settings of the LAN (Local Area Network)
IPv6 interface for the router. The router’s LAN IPv6 Address
configuration is based on the IPv6 Address and Subnet
assigned by your ISP. (A subnet with prefix /64 is supported
in LAN.)

Tunneling Connection (6rd)

After selecting the Tunneling Connection (6rd) option, the user can configure the IPv6 6rd connection settings.
The following parameters will be available for configuration:

6rd IPv6 Prefix: Enter the 6rd IPv6 address and prefix value used
here.
IPv4 Address: Enter the IPv4 address used here.
Mask Length: Enter the IPv4 mask length used here.
Assigned IPv6 Prefix: Displays the IPv6 assigned prefix value here.
6rd Border Relay IPv4 Enter the 6rd border relay IPv4 address used here.
Address:
IPv6 DNS Server: Enter the primary DNS Server address used here.
The IPv6 Internet Connection Setup Wizard is complete.
Click on the Connect button to continue. Click on the Prev button to return to
the previous page. Click on the Cancel button to discard all the changes made
and return to the main page.

IPv6 Manual Setup

There are several connection types to choose from: Auto Detection, Static IPv6, Autoconfiguration (SLAAC/DHCPv6),
PPPoE, IPv6 in IPv4 Tunnel, 6to4, 6rd, and Local Connectivity Only. If you are unsure of your connection method, please
contact your IPv6 Internet Service Provider.
Note: If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or
disabled.
Auto Detection
Select Auto Detection to have the router detect and automatically
configure your IPv6 setting from your ISP.
Click Save Settings.

Static IPv6
My IPv6 Connection is: Select Static IPv6 from the drop-down menu.
WAN IPv6 Address Enter the address settings supplied by your Internet provider
Settings: (ISP).
LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router.
LAN IPv6 Link-Local Displays the Router’s LAN Link-Local Address.

Address:
Enable Automatic IPv6 Check to enable the Autoconfiguration feature.

address assignment:
Autoconfiguration Type: Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC +

Stateless DHCPv6.
IPv6 Address Range Enter the start IPv6 Address for the DHCPv6 range for your
Start: local computers.
IPv6 Address Range Enter the end IPv6 Address for the DHCPv6 range for your
End: local computers.
Router Advertisement Enter the Router Advertisement Lifetime (in minutes).

Lifetime:

Autoconfiguration
My IPv6 Connection is: Select Autoconfiguration (Stateless/DHCPv6) from the
drop-down menu.
IPv6 DNS Settings: Select either Obtain DNS server address automatically or
Use the following DNS Address.
Primary/Secondary DNS Enter the primary and secondary DNS server addresses.
Server:

Address:

address assignment:

Stateless DHCPv6.
IPv6 Address Range Enter the start IPv6 Address for the DHCPv6 range for your
Start: local computers.
IPv6 Address Range Enter the end IPv6 Address for the DHCPv6 range for your
End: local computers.

Lifetime:

PPPoE
My IPv6 Connection is: Select PPPoE from the drop-down menu.
PPPoE Internet Enter the PPPoE account settings supplied by your Internet
Connection Type: provider (ISP).
PPPoE Session: Select Create a new session if you have IPv6.
Address Mode: Select Static IP if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases, select
Dynamic IP.
IP Address: Enter the IP address (Static PPPoE only).
User Name: Enter your PPPoE user name.
Password: Enter your PPPoE password and then retype the password in the
next box.
Service Name: Enter the ISP Service Name (optional).
Reconnect Mode: Select either Always-on, On-Demand, or Manual.
Maximum Idle Time: Enter a maximum idle time during which the Internet connection
is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
MTU: Maximum Transmission Unit - you may need to change the MTU for
optimal performance with your specific ISP. 1492 is the default MTU.
IPv6 DNS Settings: Select either Obtain IPv6 DNS servers automatically or Use the
following IPv6 DNS Servers
Primary/Secondary DNS Enter the primary and secondary DNS server addresses.
Servers:

Enable DHCP-PD: Check to enable DHCP-PD.

Address:
Enable Automatic IPv6 Check to enable the IPv6 Autoconfiguration.

address assignment:
Enable Automatic DHCP- Check to enable delegation of previxes for router addresses.
PD in LAN:

Stateless DHCPv6.
IPv6 Address Range Start: Enter the start IPv6 Address for the DHCPv6 range for your
local computers.
IPv6 Address Range End: Enter the end IPv6 Address for the DHCPv6 range for your
local computers.
Router Advertisement
Lifetime: Enter the Router Advertisement Lifetime (in minutes).

IPv6 in IPv4 Tunneling

My IPv6 Connection is: Select IPv6 in IPv4 Tunnel from the drop-down menu.
IPv6 in IPv4 Tunnel

Settings: Enter the settings supplied by your Internet provider (ISP).
IPv6 DNS Settings: Select either Obtain IPv6 DNS servers automatically or Use
the following IPv6 DNS Servers
Primary/Secondary Enter the primary and secondary DNS server addresses.
DNS Servers:

Address:

Address Assignment:
Enable Automatic Check to enable delegation of prefixes for router addresses.

DHCP-PD in LAN:
Autoconfiguration Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless

Type: DHCPv6.
IPv6 Address Range Enter the start IPv6 Address for the DHCPv6 range for your local
Start: computers.
IPv6 Address Range Enter the end IPv6 Address for the DHCPv6 range for your local
End: computers.

Lifetime:

6 to 4 Tunneling
My IPv6 Connection is: Select 6 to 4 from the drop-down menu.
WAN IPv6 Address Enter the IPv6 settings supplied by your Internet provider (ISP).
Settings:
Primary/Secondary Enter the primary and secondary DNS server addresses.

DNS Servers:

Address:

Address Assignment:
Autoconfiguration Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless

Type: DHCPv6.
IPv6 Address Range Enter the start IPv6 Address for the DHCPv6 range for your local
Start: computers.
IPv6 Address Range Enter the end IPv6 Address for the DHCPv6 range for your local
End: computers.
Router Advertisemt Enter the Router Advertisement Lifetime (in minutes).

Lifetime:

6rd
My IPv6 Connection is: Select 6rd from the drop-down menu.
WAN IPv6 Address Enter the address settings supplied by your Internet provider
Settings: (ISP).

Address:

address assignment:
Autoconfiguration Type: Select Stateful (DHCPv6), SLAAC+RDNSS or SLAAC + Stateless

DHCPv6.

Lifetime:

Local Connectivity
My IPv6 Connection is: Select Local Connectivity Only from the drop-
down menu.
LAN IPv6 Link-Local Displays the IPv6 address of the router.

Address:

mydlink Settings
The DIR-850L features a cloud service that pushes information such as firmware upgrade notifications, user activity, and
intrusion alerts to the mydlink™ app on Android and Apple mobile devices. To insure that your router is up-to-date with the
latest features, mydlink™ will notify you when an update is available for your router. You can also monitor a user’s online activity
with real-time website browsing history, maintaining a safe and secure environment, especially for children at home.
On this page the user can configure the mydlink™ settings for this router. This feature will allow us to use the mydlink cloud
services that includes online access and management of this router through the mydlink portal website or portable device
applications like iOS apps and Android applications.
In the mydlink section, we can view the registration status of the mydlink account service. The mydlink Service field will either
display Registered or Non-Registered. In the Register mydlink Service section, we can register or modify a mydlink account.
Click on the Register mydlink Service button to initiate this procedure.
mydlink Service: Displays whether your device is registered with a mydlink

account or not. If you are registered, your mydlink e-mail
address will be displayed.
mydlink E-mail: If you are registered, your mydlink E-mail address will be
displayed.
Register mydlink Click to go to the mydlink website to register or edit your

Settings: settings. Please refer to page 19 for the registration steps.

Advanced
Virtual Server
This will allow you to open a single port. If you would like to open a range of ports, refer to the next page.
Name: Enter a name for the rule or select an application from

the drop-down menu. Select an application and click
<< to populate the fields.
IP Address: Enter the IP address of the computer on your local

network that you want to allow the incoming
service to. If your computer is receiving an IP address
automatically from the router (DHCP), you computer
will be listed in the “Computer Name” drop-down
menu. Select your computer and click <<.
Private Port/ Enter the port that you want to open next to Private
Public Port: Port and Public Port. The private and public ports are
usually the same. The public port is the port seen from
the Internet side, and the private port is the port being
used by the application on the computer within your
local network.
Protocol Type: Select TCP, UDP, or Both from the drop-down menu.
Schedule: The schedule of time when the Virtual Server Rule

will be enabled. The schedule may be set to Always,
which will allow the particular service to always be
enabled. You can create your own times in the Tools
> Schedules section.
Inbound Filter: Select Allow All (most common) or a created Inbound

filter. You may create your own inbound filters in the
Advanced > Inbound Filter page.

Port Forwarding
This will allow you to open a single port or a range of ports.
Name: Enter a name for the rule or select an application

from the drop-down menu. Select an application
and click << to populate the fields.
IP Address: Enter the IP address of the computer on your local

network that you want to allow the incoming service
to. If your computer is receiving an IP address
automatically from the router (DHCP), you computer
will be listed in the “Computer Name” drop-down
menu. Select your computer and click <<.
TCP/UDP: Enter the TCP and/or UDP port or ports that you
want to open. You can enter a single port or a range
of ports. Separate ports with a comma.
Example: 24,1009,3000-4000
Schedule: The schedule of time when the Virtual Server Rule

which will allow the particular service to always be
enabled. You can create your own times in the Tools
> Schedules section.
Inbound Filter: Select Allow All (most common) or a created

Inbound filter. You may create your own inbound
filters in the Advanced > Inbound Filter page.

Application Rules
Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others.
These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of
these applications work with the DIR-850L. If you need to run applications that require multiple connections, specify the port
normally associated with an application in the “Trigger Port” field, select the protocol type as TCP or UDP, then enter the firewall
(public) ports associated with the trigger port to open them for inbound traffic.
The DIR-850L provides some predefined applications in the table on the bottom of the web page. Select the application you
want to use and enable it.
Name: Enter a name for the rule. You may select a

pre-defined application from the drop-down menu
and click <<.
Trigger: This is the port used to trigger the application. It

can be either a single port or a range of ports.
Traffic Type: Select the protocol of the trigger port (TCP, UDP,
or Both).
Firewall: This is the port number on the Internet side that

will be used to access the application. You may
define a single port or a range of ports. You can use
a comma to add multiple ports or port ranges.
Traffic Type: Select the protocol of the firewall port (TCP, UDP,
or Both).
Schedule: The schedule of time when the Application Rule

which will allow the particular service to always
be enabled. You can create your own times in the
Tools > Schedules section.
QoS Engine
The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled
and application priority is not automatically classified. The QoS section contains a queuing mechanism, traffic shaping and classification. It supports
two kinds of queuing mechanisms. Strict Priority Queue (SPQ) and Weighted Fair Queue (WFQ). SPQ will process traffic based on traffic priority.
Queue1 has the highest priority and Queue4 has the lowest priority. WFQ will process traffic based on the queue weight. Users can configure each
queue’s weight. The sum of all the queue’s weight must be 100. When surfing the Internet, the system will do traffic shaping based on the uplink
and downlink speed. The classification rules can be used to classify traffic to different queues, then SPQ or WFQ will do QoS based on the queue’s
priority or weight.
Enable QoS: This option is disabled by default. Enable this option for better
performance and experience with online games and other
interactive applications, such as VoIP.
Uplink Speed: The speed at which data can be transferred from the router to
your ISP. This is determined by your ISP.
Downlink Speed: The speed at which data can be transferred from the Internet to
your router. This is determined by your ISP.
Queue Type: Select either Strict Priority Queue (rank in order) or Weighted
Fair Queue (percentage).
Queue ID: The Queue ID used will be displayed in the first column.
Queue Priority: When Strict Priority Queue is selected, the Queue Priority will be
displayed in the second column.
Queue Weight: When the Weighted Fair Queue option is selected, you will be able
to manually enter the Queue Weight for each individual Queue
ID in the second column.

After specifying the QoS framework used, in the QoS setup section, the user can now create individual rules for scenarios that
require the use of traffic control and data priority manipulation.
Classification The QoS Engine supports overlaps between rules, where more than one rule can match for a specific message flow. If more than one
Rules: rule is found to match the rule with the highest priority will be used.
Name: Create a name for the rule that is meaningful to you.
Queue ID: The priority of the message flow is entered here -- 1 receives the highest priority (most urgent) and 255 receives the lowest priority
(least urgent).
Protocol: The protocol used by the messages.
Local IP Range: The rule applies to a flow of messages whose LAN-side IP address falls within the range set here.
Local Port The rule applies to a flow of messages whose LAN-side port number is within the range set here.
Range:
Remote IP The rule applies to a flow of messages whose WAN-side IP address falls within the range set here.
Range:
Remote Port The rule applies to a flow of messages whose WAN-side port number is within the range set here.
Range:
Application Port: Select a service or port you want to assign to this rule.
Click on the Save Settings button to accept the changes made or click on the Don’t Save Settings button to discard the
changes made.

Network Filters
Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from
accessing the network. You can either manually add a MAC address or select the MAC address from the list of clients that are
currently connected to the Broadband Router.
Configure MAC Select Turn MAC Filtering Off, Allow MAC addresses
Filtering: listed below, or Deny MAC addresses listed below
from the drop-down menu.
MAC Address: Enter the MAC address you would like to filter.
To find the MAC address on a computer, please refer

to the Networking Basics section in this manual.
DHCP Client List: Select a DHCP client from the drop-down menu and
click << to copy that MAC Address.
Schedule: Select a pre-defined or user created schedule from

the drop-down menu, or click New Schedule to
create a new schedule. You set a specific time frame
for the MAC filter rule to be active.

Access Control
The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to
only grant access to approved sites, limit web access based on time or dates, and/or block access from applications like P2P
utilities or games.
Enable Access Check the Enable Access Control box, and then
Control: click on Add Policy to start the Wizard.
Access Control Wizard

Click Next to continue with the wizard.

Enter a name for the policy and then click Next to continue.
Select a schedule (i.e., Always) from the drop-down menu and then
click Next to continue.
Enter the following information and then click Next to continue.
• Address Type - Select IP address, MAC address, or Other

Machines.
• IP Address - Enter the IP address of the computer you want
to apply the rule to.
• Machine Address - Enter the PC MAC address or click on
Clone Your PCs MAC Address.
Click Add and then click Next to continue.

Select the filtering method.
If you choose to Block Some Access, check Apply Web Filter and/or
Apply Advanced Port Filters.

Add Port Filter Rules:

Enable - Check to enable the rule.
Name - Enter a name for your rule.
Dest IP Start - Enter the starting IP address.
Dest IP End - Enter the ending IP address.
Protocol - Select the protocol.
Dest Port Start - Enter the starting port number.
Dest Port End - Enter the ending port number.
To enable web logging, click Enabled.
Click Save to save the access control rule.
Your newly created policy will now show up under Policy Table.

Website Filters
Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network.
To use this feature select to Allow or Deny, enter the domain or website and click Save Settings. You must also select Apply
Web Filter under the Access Control section (page 81).
Configure Select either DENY computers access to

Website Filter: ONLY these sites or ALLOW computers
access to ONLY these sites.
Website URL/ Enter the keywords or URLs that you want

Domain: to allow or block. Click Save Settings.

Inbound Filters
The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can
configure inbound data filtering rules that control data based on an IP address range. Inbound Filters can be used with Virtual
Server, Port Forwarding, or Remote Administration features.
Name: Enter a name for the inbound filter rule.
Action: Select Allow or Deny.
Remote IP Check to enable rule.

Range: Enable:
Remote IP Start: Enter the starting IP address. Enter 0.0.0.0

if you do not want to specify an IP range.
Remote IP End: Enter the ending IP address. Enter

255.255.255.255 if you do not want to
specify and IP range.
Add: Click the Add button to apply your settings.

You must click Save Settings at the top to
save the settings.
Inbound Filter This section will list any rules that are
Rules List: created. You may click the Edit icon to
change the settings or enable/disable the
rule, or click the Delete icon to remove
the rule.

Firewall Settings
A firewall protects your network from the outside world. The DIR-850L offers a firewall type functionality. The SPI feature helps
prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications.
If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the
chosen computer completely to the outside world.
Enable SPI: SPI (Stateful Packet Inspection, also known as dynamic packet filtering)
helps to prevent cyber attacks by tracking more state per session. It
validates that the traffic passing through the session conforms to the
protocol.
Anti-Spoof Enable this feature to protect your network from certain kinds of
Checking: “spoofing” attacks.
Enable DMZ: If an application has trouble working from behind the router, you can
expose one computer to the Internet and run the application on that
computer.
Note: Placing a computer in the DMZ may expose that computer to a variety
of security risks. Use of this option is only recommended as a last resort.
DMZ IP Address: Specify the IP address of the computer on the LAN that you want to have
unrestricted Internet communication. If this computer obtains it’s IP
address automatically using DHCP, be sure to make a static reservation
on the Setup > Network Settings page so that the IP address of the
DMZ machine does not change.
PPTP: Allows multiple machines on the LAN to connect to their corporate network using PPTP protocol.
IPSEC (VPN): Allows multiple VPN clients to connect to their corporate network using IPSec. Some VPN clients support traversal of IPSec through
NAT. This ALG may interfere with the operation of such VPN clients. If you are having trouble connecting with your corporate network,
try turning this ALG off. Please check with the system administrator of your corporate network whether your VPN client supports
NAT traversal.

RTSP: Allows application that uses Real Time Streaming Protocol to receive streaming media from the Internet. QuickTime and Real Player
are some of the common applications using this protocol.
SIP: Allows devices and applications using VoIP (Voice over IP) to communicate across NAT. Some VoIP applications and devices have
the ability to discover NAT devices and work around them. This ALG may interfere with the operation of such devices. If you are
having trouble making VoIP calls, try turning this ALG off.

Routing
The Routing option is an advanced method of customizing specific routes of data through your network.
Name: Enter a name for your route.
Destination IP: Enter the IP address of packets that will take this
route.
Netmask: Enter the netmask of the route, please note

that the octets must match your destination IP
address.
Gateway: Enter your next hop gateway to be taken if this

route is used.
Metric: The route metric is a value from 1 to 16 that

indicates the cost of using this route. A value 1 is
the lowest cost and 15 is the highest cost.
Interface: Select the interface that the IP packet must use to

transit out of the router when this route is used.

Advanced Wireless
Transmit Power: Set the transmit power of the antennas.
WLAN Partition: This enables 802.11d operation. 802.11d is a wireless

specification developed to allow implementation of
wireless networks in countries that cannot use the
802.11 standard. This feature should only be enabled
if you are in a country that requires it.
WMM Enable: WMM is QoS for your wireless network. This will improve
the quality of video and voice applications for your
wireless clients.
Short GI: Check this box to reduce the guard interval time
therefore increasing the data capacity. However, it’s less
reliable and may create higher data loss.
HT20/40 Coexistence: Enable this option to reduce interference from

other wireless networks in your area. If the channel
width is operating at 40MHz and there is another
wireless network’s channel over-lapping and causing
interference, the router will automatically change to
20MHz.

Wi-Fi Protected Setup (WPS)

Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the “Initial setup” as well
as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certified it across different products as well as manufactures.
The process is just as easy as pressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin
Code Method. The time reduction in setup and ease of use are quite beneficial, while the highest wireless Security setting of
WPA2 is automatically used.
Enable: Enable the Wi-Fi Protected Setup feature.
Note: if this option is unchecked, the WPS button on the side of

the router will be disabled.
WiFi Protected Displays the current WPS status.

Setup:
Lock WPS-PIN Locking the WPS-PIN Method prevents the settings from
Setup: being changed by any external registrar using its PIN. Devices
can still be added to the wireless network using the Wi-Fi
Protected Setup Push Button Configuration (WPS-PBC). It
is still possible to change wireless networks settings with
Manual Wireless Network Setup or Wireless Network Setup
Wizard.
PIN Settings: A PIN is a unique number that can be used to add the router
to an existing network or to create a new network. Only the
Administrator (“admin” account) can change or reset the PIN.
PIN: Shows the current PIN.
Reset PIN to Click to restore the default PIN of the router.

Default:
Generate New PIN: Create a random number that is a valid PIN. This becomes the
router’s PIN. You can then copy this PIN to the user interface
of the wireless client.

Add Wireless This Wizard helps you add wireless devices to the wireless network.
Station:
The wizard will either display the wireless network settings to guide you through manual configuration, prompt you to enter the
PIN for the device, or ask you to press the configuration button on the device. If the device supports Wi-Fi Protected Setup and has a
configuration button, you can add it to the network by pressing the configuration button on the device and then the on the router
within 60 seconds. The status LED on the router will flash three times if the device has been successfully added to the network.
There are several ways to add a wireless device to your network. A “registrar” controls access to the wireless network. A registrar
only allows devices onto the wireless network if you have entered the PIN, or pressed a special Wi-Fi Protected Setup button on the
device. The router acts as a registrar for the network, although other devices may act as a registrar as well.
Connect Your Click to start the wizard and skip to page 44.
Wireless Device:
WPS Button
You can also simply press the WPS button on the side of the router, and then press the WPS button on
your wireless client to automatically connect without logging into the router.
WPS Button
Refer to page 115 for more information.

Advanced Network Settings

Enable UPnP IGD: To use the Universal Plug and Play (UPnP™) feature check
the box. UPnP provides compatibility with networking
equipment, software and peripherals.
Enable WAN Ping Checking the box will allow the DIR-850L to respond
Response: to pings. Unchecking the box may provide some extra
security from hackers.
WAN Port Speed: You may set the port speed of the Internet port to 10Mbps,
100Mbps, 1000Mbps, or Auto (recommended).
Enable IPV4 Check the box to allow multicast traffic to pass through
Multicast Streams: the router from the Internet (IPv4).
Enable IPV6 Check the box to allow multicast traffic to pass through
Multicast Streams: the router from the Internet (IPv6).

Guest Zone
The Guest Zone feature will allow you to create temporary zones that can be used by guests to access the Internet. These zones
will be separate from your main wireless network. You may configure different zones for the 2.4GHz and 5GHz wireless bands.
Enable Routing Check to allow network connectivity between the

Between Zones: different zones created.
Enable Guest Check to enable the Guest Zone feature.

Zone:
Schedule: The schedule of time when the Guest Zone will be

active. The schedule may be set to Always, which will
allow the particular service to always be enabled. You
can create your own times in the Tools > Schedules
section or click New Schedule.
Wireless Enter a wireless network name (SSID) that is different

Network Name: from your main wireless network.
Security Mode: Select the type of security or encryption you would

like to enable for the guest zone.

IPv6 Firewall
The DIR-850L’s IPv6 Firewall feature allows you to configure which kind of IPv6 traffic is allowed to pass through the device.
This feature functions in a similar way to the IP Filters feature.
Enable IPv6 Check the box to enable the IPv6 firewall simple security.
Simple Security:
Configure IPv6 Select an action from the drop-down menu.

Filtering below:
Name: Enter a name to identify the IPv6 firewall rule.
Schedule: Use the drop-down menu to select the time schedule that the IPv6
Firewall Rule will be enabled on. The schedule may be set to Always,
which will allow the particular service to always be enabled. You can
create your own times in the Tools > Schedules section.
Source: Use the Interface drop-down menu to specify the interface that
connects to the source IPv6 addresses of the firewall rule.
IP Address Range: Enter the source IPv6 address range in the adjacent IP Address
Range field.
Dest: Use the Interface drop-down menu to specify the interface that connects to the destination IP addresses of the firewall rule.
Protocol: Select the protocol of the firewall port (All, TCP, UDP, or ICMP).
Port Range: Enter the first port of the range that will be used for the firewall rule in the first box and enter the last port in the field in the second
box.

IPv6 Routing
This page allows you to specify custom routes that determine how data is moved around your network.
Route List: Check the box next to the route you wish to enable.
Name: Enter a specific name to identify this route.
Destination IP/ This is the IP address of the router used to reach the
Prefix Length: specified destination or enter the IPv6 address prefix
length of the packets that will take this route.
Metric: Enter the metric value for this rule here.
Interface: Use the drop-down menu to specify if the IP packet

must use the WAN or LAN interface to transit out of
the Router.
Gateway: Enter the next hop that will be taken if this route is used.

Tools
Admin
This page will allow you to change the Administrator password and also enable Remote Management.
Admin Password: Enter a new password for the Admin login name. Enter again to verify password.
Gateway Name: Enter a name for your router.
Enable Graphical Enables a challenge-response test to require users to type letters or numbers
Authentication: from a distorted image displayed on the screen to prevent online hackers and
unauthorized users from gaining access to your router’s network settings.
Enable HTTPS Check to enable HTTPS to connect to the router securely. This means to connect
Server: to the router, you must enter https://192.168.0.1 (for example) instead of
http://192.168.0.1.
Enable Remote Remote management allows the DIR-850L to be configured from the Internet
Management: by a web browser. A username/password is still required to access the Web
Management interface.
Remote Admin Port: The port number used to access the DIR-850L is used in the URL. Example:
http://x.x.x.x:8080 whereas x.x.x.x is the Internet IP address of the DIR-850L
and 8080 is the port used for the Web Management interface.
If you have enabled HTTPS Server, you must enter https:// as part of the URL
to access the router remotely.
Remote Admin This section will list any rules that are created. You may click the Edit icon to
Inbound Filter: change the settings or enable/disable the rule, or click the Delete icon to
remove the rule. Details will display the current status.

Time
The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock.
From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to
automatically adjust the time when needed.
Time: Displays the current date and time of the router.
Time Zone: Select your Time Zone from the drop-down

menu.
Enable Daylight To select Daylight Saving time manually, select

Saving: enabled or disabled, and enter a start date and
an end date for daylight saving time.
Enable NTP Server: NTP is short for Network Time Protocol. A NTP
server will sync the time and date with your
router. This will only connect to a server on the
Internet, not a local server. Check the box to
enable this feature.
NTP Server Used: Enter the IP address of a NTP server or select one
from the drop-down menu.
Manual: To manually input the time, enter the values

in these fields for the Year, Month, Day, Hour,
Minute, and Second and then click Set Time.
You can also click Copy Your Computer’s Time

Settings to synch the date and time with the
computer you are currently on.

SysLog
The DIR-850L keeps a running log of events and activities occurring on the Router. You may send these logs to a SysLog server
on your network.
Enable Logging to Check this box to send the router logs to a SysLog
SysLog Server: Server.
SysLog Server IP The address of the SysLog server that will be

Address: used to send the logs. You may also select your
computer from the drop-down menu (only if
receiving an IP address from the router via DHCP).

Email Settings
The Email feature can be used to send the system log files, router alert messages, and firmware update notification to your
email address.
Enable Email When this option is enabled, router activity logs are emailed to a
Notification: designated email address.
From Email Address: This email address will appear as the sender when you receive a log
file or firmware upgrade notification via email.
To Email Address: Enter the email address where you want the email sent.
Email Subject: Add a subject line to your email.
SMTP Server Address: Enter the SMTP server address for sending email.
SMTP Server Port: Enter the SMTP port used on the server.
Enable Authentication: Check this box if your SMTP server requires authentication.
Account Name: Enter your account for sending email.
Password: Enter the password associated with the account. Re-type the
password associated with the account.
On Log Full: When this option is selected, logs will be sent via email to your
account when the log is full.
On Schedule: Selecting this option will send the logs via email according to
schedule.
Schedule: This option is enabled when On Schedule is selected. You can select
a schedule from the list of defined schedules. To create a schedule,
go to Tools > Schedules.

System
This section allows you to manage the router’s configuration settings, reboot the router, and restore the router to the factory
default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created.
Save Settings to Use this option to save the current router

Local Hard Drive: configuration settings to a file on the hard disk of
the computer you are using. First, click the Save
button. A file dialog will appear, allowing you to
select a location and file name for the settings.
Load Settings Use this option to load previously saved router

from Local Hard configuration settings. First, use the Browse option
Drive: to find a previously saved file of configuration
settings. Then, click the Load button to transfer
those settings to the router.
Restore to This option will restore all configuration settings

Factory Default back to the settings that were in effect at the
Settings: time the router was shipped from the factory.
Any settings that have not been saved will be
lost, including any rules that you have created. If
you want to save the current router configuration
settings, use the Save button above.
Reboot the Click to reboot the router.

Device:
Clear Language Click to remove any installed language packs.

Pack:

Firmware
You can upgrade the firmware of the router here. Make sure the firmware you want to use is on the local hard drive of the
computer.
Firmware Upgrade
Choose File: After you have downloaded the new firmware, click
Choose File to locate the firmware update on your
hard drive. Click Upload to complete the firmware
upgrade.
Upload: Once you have a firmware update on your computer,

use this option to browse for the file and then upload
the information into the access point.
Language Pack Upgrade

You can change the language of the web UI by uploading
available language packs.
Choose File: After you have downloaded the new language pack,
click Choose File to locate the language pack file
on your hard drive. Click Upload to complete the
language pack upgrade.
Upload: Once you have a language pack update on your

computer, use this option to browse for the file and
then upload the information into the access point.

Dynamic DNS
The Dynamic DNS (DDNS) feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you
have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service
Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name
to connect to your server no matter what your IP address is.
Enable Dynamic Domain Name System is a method of

Dynamic DNS: keeping a domain name linked to a changing IP
Address. Check the box to enable DDNS.
Server Select your DDNS provider from the drop-down

Address: menu or enter the DDNS server address.
Host Name: Enter the Host Name that you registered with
your DDNS service provider.
Username or Enter the Username or key for your DDNS

Key: account.
Password or Enter the Password or key for your DDNS account.

Key:
Timeout: Enter a timeout time (in hours).
Status: Displays the current connection status.

DDNS for IPv6 Hosts

Enable: Check the box to enable DDNS for IPv6 Hosts.
IPv6 Enter the IPv6 address of your computer/server in

Address: your local network. You can click the << button and
select a computer/server from the drop-down list.
Host Name: Enter the IPv6 Host Name that you registered with
your DDNS service provider.
IPv6 DDNS Once you save your entry, the IPv6 DDNS host
List: information will be displayed here.
Enable: Check to enable the entry.
Host Name: Displays the name of your IPv6 DDNS host.
IPv6 Address: Displays the IPv6 address of your computer/server

associated with the IPv6 DDNS host.
Edit/Delete: Click the edit icon to make changes to the entry or

click the delete icon to remove the entry.

System Check
Ping Test: The Ping Test is used to send Ping packets to test if a
computer is on the Internet. Enter the IP address that you
wish to Ping and click Ping.
IPv6 Ping Test: Enter the IPv6 address that you wish to Ping and click Ping.
Ping Results: The results of your ping attempts will be displayed here.

Schedules
Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to
8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm.
Name: Enter a name for your new schedule.
Days: Select a day, a range of days, or All Week to

include every day of the week.
Time: Check All Day - 24hrs or enter a start and end

time for your schedule.
Add: You must click Add to save your schedule rule.
Schedule Rules The list of schedules will be listed here. Click the
List: Edit icon to make changes or click the Delete icon
to remove the schedule.

Status
Device Info
This page displays the current information for the DIR-850L. It will display the LAN, WAN (Internet), and Wireless information.
If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed.
Use Release to disconnect from your ISP and use Renew to connect to your ISP.
If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect
to drop the PPPoE connection and use Connect to establish the PPPoE connection.
General: Displays the router’s time and firmware version.
WAN: Displays the MAC address and the public IP settings.
LAN: Displays the MAC address and the private (local) IP settings for the
router.
Wireless LAN1: Displays the 2.4GHz wireless MAC address and your wireless settings
such as SSID and Channel.
Wireless LAN2: Displays the 5GHz wireless MAC address and your wireless settings
such as SSID and Channel.
LAN Computers: Displays computers and devices that are connected to the router via
Ethernet and that are receiving an IP address assigned by the router
(DHCP).

Logs
The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory
for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view
the router logs. You can define what types of events you want to view and the level of the events to view. This router also has
external Syslog Server support so you can send the log files to a computer on your network that is running a Syslog utility.
Save Log File: Click Save to save log file to local hard drive.
Log Type & You can select the type and level indicating what you
Level: would like to keep track of.
Refresh: Updates the log details on the screen so it displays any

recent activity.
First Page: Click to go to the first page.
Last Page: Click to go to the last page.
Previous: Click to go back one page.
Next: Click to go to the next page.
Clear: Clears all of the log contents.
Link to Email Clicking on this will take you to the Tools > Email
Log Settings: Settings page.

Statistics
The screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the DIR-850L on both
the WAN, LAN ports and the wireless segments. The traffic counter will reset if the device is rebooted.

Internet Sessions
The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a
conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer.

Wireless
The wireless client table displays a list of current connected wireless clients. This table also displays the connection rate and
MAC address of the connected wireless clients.

Routing
This page will display your current routing table.

IPv6
The IPv6 page displays a summary of the Router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients.

IPV6 Routing
This page displays the IPV6 routing details configured for your router.

Support

Connect a Wireless Client to your Router

WPS Button
The easiest and most secure way to connect your wireless devices to the router is WPS (Wi-Fi Protected Setup). Most wireless
devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button
(or a software utility with WPS) that you can press to connect to the DIR-850L router. Please refer to your user manual for the
wireless device you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps below:
Step 1 - Press the WPS button on the DIR-850L

WPS Button
for about one second. The Internet LED
on the front will start to blink.
Step 2 - Within two minutes, press the WPS button on your wireless client (or launch the software utility and start the WPS
process).
Step 3 - Allow up to one minute to configure. Once the Internet light stops blinking, you will be connected and your wireless
connection will be secure with WPA2.

Windows® 8
1. Click on the wireless computer icon in your system tray (lower-right
corner next to the time).
2. A list of available wireless networks will appear.
3. Click the wireless network (SSID) you want to connect to and then
click Connect.
4. If the network is secure/encrypted, enter the Wi-Fi password

(security key) and click Next.

5. Click either to enable or disable file sharing.
6. You will now be connected to your wireless network.
If you get a good signal but cannot access the Internet, confirm the encryption by reviewing the profile or check the TCP/IP
settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.

Windows® 7
WPA/WPA2
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your
wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
1. Click on the wireless icon in your system tray (lower-right corner).
Wireless Icon
2. The utility will display any available wireless networks in your area.

3. Highlight the wireless network (SSID) you would like to connect to

and click the Connect button.
If you get a good signal but cannot access the Internet, check your
TCP/IP settings for your wireless adapter. Refer to the Networking
Basics section in this manual for more information.
4. The following window appears while your computer tries to

connect to the router.

5. Enter the same security key or passphrase that is on your router and
click Connect. You can also connect by pushing the WPS button on
the router.
It may take 20-30 seconds to connect to the wireless network. If the

connection fails, please verify that the security settings are correct. The
key or passphrase must be exactly the same as on the wireless router.

WPS
The WPS feature of the DIR-850L can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to
configure the WPS feature:
1. Click the Start button and select Computer from the Start menu.
2. Click Network on the left side.

3. Double-click the DIR-850L.
4. Input the WPS PIN number (displayed in the WPS window on the
Router’s LCD screen or in the Setup > Wireless Setup menu in
the Router’s Web UI) and click Next.

5. Type a name to identify the network.
6. To configure advanced settings, click the icon.

7. The following window appears while the Router is being

configured.

Wait for the configuration to complete.
8. The following window informs you that WPS on the router has
been setup successfully.
Make a note of the security key as you may need to provide this
security key if adding an older wireless device to the network in
the future.
9. Click Close to complete WPS setup.

Section 5 - Connecting to a Wireless Network
Windows Vista®
Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility, please refer to the user
manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option
similar to the Windows Vista® utility as seen below.
If you receive the Wireless Networks Detected bubble, click on the

center of the bubble to access the utility.
or
Right-click on the wireless computer icon in your system tray (lower-right
corner next to the time). Select Connect to a network.
The utility will display any available wireless networks in your area. Click
on a network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you TCP/
IP settings for your wireless adapter. Refer to the Networking Basics
section in this manual for more information.

WPA/WPA2
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your
wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
1. Open the Windows Vista® Wireless Utility by right-clicking on the

wireless computer icon in your system tray (lower right corner of
screen). Select Connect to a network.
2. Highlight the wireless network (SSID) you would like to connect

to and click Connect.

3. Enter the same security key or passphrase that is on your router and
click Connect.

connection fails, please verify that the security settings are correct. The
key or passphrase must be exactly the same as on the wireless router.

WPS/WCN 2.0
The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up
depends on whether you are using Windows Vista® to configure the router or third party software.
When you first set up the router, Wi-Fi protection is disabled and unconfigured. To enjoy the benefits of Wi-Fi protection, the
router must be both enabled and configured. There are three basic methods to accomplish this: use Windows Vista’s built-in
support for WCN 2.0, use software provided by a third party, or manually configure.
If you are running Windows Vista®, log into the router and click the Enable checkbox in the Basic > Wireless section. Use the
Current PIN that is displayed on the Advanced > Wi-Fi Protected Setup section or choose to click the Generate New PIN
button or Reset PIN to Default button.
If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are finished, proceed
to the next section to set up the newly-configured router.

Windows® XP
Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). If you are using another company’s utility,
please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have
a “site survey” option similar to the Windows® XP utility as seen below.
If you receive the Wireless Networks Detected bubble, click on the

center of the bubble to access the utility.
or
Right-click on the wireless computer icon in your system tray (lower-right
corner next to the time). Select View Available Wireless Networks.
The utility will display any available wireless networks in your area.
Click on a network (displayed using the SSID) and click the Connect
button.
If you get a good signal but cannot access the Internet, check you
TCP/IP settings for your wireless adapter. Refer to the Networking
Basics section in this manual for more information.

WPA/WPA2
It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are
joining an existing network, you will need to know the WPA key being used.
1. Open the Windows® XP Wireless Utility by right-clicking on the

wireless computer icon in your system tray (lower-right corner
of screen). Select View Available Wireless Networks.
2. Highlight the wireless network (SSID) you would like to

connect to and click Connect.

3. The Wireless Network Connection box will appear. Enter the WPA-PSK
passphrase and click Connect.

connection fails, please verify that the WPA-PSK settings are correct. The
WPA-PSK passphrase must be exactly the same as on the wireless router.

Section 6 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DIR-850L. Read the
following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a different
operating system, the screenshots on your computer will look similar to the following examples.
1. Why can’t I access the web-based configuration utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website nor do you
have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must
be on the same IP subnet to connect to the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:

- Microsoft Internet Explorer® 7 and higher
- Mozilla Firefox 3.5 and higher
- Google™ Chrome 8 and higher
- Apple Safari 4 and higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a
different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be
on.
• Disable any Internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice, Sygate,
Norton Personal Firewall, and Windows® XP firewall may block access to the configuration pages. Check the help files included
with your firewall software for more information on disabling or configuring it.

• Configure your Internet settings:
• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click
the button to restore the settings to their defaults.
• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button.
Make sure nothing is checked. Click OK.
• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
• Close your web browser (if open) and open it.
• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This
should open the login page for your web management.
• If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30
seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your router. Unfortunately this process will
change all your settings back to the factory defaults.
To reset the router, locate the reset button (hole) on the bottom of the unit. With the
router powered on, use a paperclip to hold the button down for 10 seconds. Release the
button and the router will go through its reboot process. Wait about 30 seconds to access
the router. To re-configure the router, refer to page 13.
Reset Router/Forgot Password

3. Why can’t I connect to certain sites or send and receive e-mails when connecting through my router?
If you are having a problem sending or receiving e-mail, or connecting to secure sites such as eBay, banking sites, and Hotmail,
we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc).
To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be
another computer, or a URL.
• Click on Start and then click Run.
• Windows® 95, 98, and Me users type in command (Windows® NT, 2000, XP, Vista®, and 7 users type in cmd) and
press Enter (or click OK).
• Once the window opens, you’ll need to do a special ping. Use the following syntax:
ping [url] [-f] [-l] [MTU value]
Example: ping yahoo.com -f -l 1472

You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented
packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the
proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480).
Once you find your MTU, you can now configure your router with the proper MTU size.
To change the MTU rate on your router follow the steps below:
• Open your browser, enter the IP address of your router (192.168.0.1) and click OK.
• Enter your username (admin) and password (blank by default). Click OK to enter the web configuration page
for the device.
• Click on Setup and then click Manual Configure.
• To change the MTU enter the number in the MTU field and click Save Settings to save your settings.
• Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in increments
of ten.

Appendix A - Wireless Basics
Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless
connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link
wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able
to enjoy the freedom that wireless networking delivers.
A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of
wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops
and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently.
Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users.
Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop
systems support the same protocols as Ethernet adapter cards.
Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to
use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide
this link.

What is Wireless?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio
frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network.
Why D-Link Wireless?
D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link
delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network.
How does wireless work?
Wireless works similar to how cordless phones work, through radio signals to transmit data from one point A to point B. But
wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area
to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN),
and Wireless Personal Area Network (WPAN).
Wireless Local Area Network (WLAN)
In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point
has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access
point, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve
places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many
other outdoor venues.

Wireless Personal Area Network (WPAN)
Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to
30 feet away.
Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as
much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other
devices that operate on batteries.
Who uses wireless?
Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, office, business,
D-Link has a wireless solution for it.
Home
• Gives everyone at home broadband access
• Surf the web, check email, instant message, etc.
• Gets rid of the cables around the house
• Simple and easy to use
Small Office and Home Office

• Stay on top of everything at home as you would at office
• Remotely access your office network from home
• Share Internet connection and printer with multiple computers
• No need to dedicate office space

Where is wireless used?
Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming
so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public
places is usually called “hotspots”.
Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations
like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers.
Wireless network is easy to setup, but if you’re installing it for the first time it could be quite a task not knowing where to start.
That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.
Tips
Here are a few things to keep in mind, when you install a wireless network.
Centralize your router or Access Point
Make sure you place the router/access point in a centralized location within your network for the best performance. Try to
place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have
a two-story home, you may need a repeater to boost the signal to extend the range.
Eliminate Interference
Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/
access point. This would significantly reduce any interference that the appliances might cause since they operate on same
frequency.

Security
Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on
the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up.
Wireless Modes
There are basically two modes of networking:

• Infrastructure – All wireless clients will connect to an access point or wireless router.
• Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network
adapters on each computer, such as two or more DIR-850L wireless network Cardbus adapters.
An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the
wireless router or access point.
An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc
mode to communicate.

Appendix B - Networking Basics
Networking Basics
Check your IP address
After you install your new D-Link wireless adapter and have established a wireless connection, by default, the TCP/IP settings should be set to obtain
an IP address from a DHCP server (i.e., router) automatically. To verify your IP address, please follow the steps below.
Windows® 8 Users
• Press the Windows key and R together. Type cmd in the box and click OK.
• At the prompt, type ipconfig and press Enter.
• This will display the IP address, subnet mask, and default gateway of your adapter.
Windows® 7/Vista® Users
• Click Start, type cmd in the search box and then click OK.
• This will display the IP address, subnet mask, and default gateway of your adapter.
Windows® XP Users
• Click on Start > Run. In the run box type cmd and click OK.
• This will display the IP address, subnet mask, and the default gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may
block a DHCP request on newly installed adapters.
Statically Assign an IP Address

If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:
Windows® 8 Users
• Press the Windows key and then type IP. Click Settings on the right side and then click View Network Connections.
• Right-click on the adapter which represents your D-Link wireless network adapter.
• Highlight Internet Protocol Version 4 (TCP /IPv4) and click

Properties.
• Click Use the following IP address and enter an IP address that is on

the same subnet as your network or LAN IP address on your router
or network.
Example: If the router’s LAN IP address is 192.168.0.1, make your IP

address 192.168.0.X where X is a number between 2 and 99. Make
sure that the number you choose is not in use on the network.
• Set Default Gateway the same as the LAN IP address of your router
or gateway.
• Set Primary DNS the same as the LAN IP address of your router or
gateway.
• The Secondary DNS is optional (you may enter a DNS server from
your ISP).
• Click OK to save your settings.

Windows® 7/ Vista® Users
• Click on Start > Control Panel (make sure you are in Classic View). Double-click on the Network and Sharing Center
icon. If you are using Windows Vista, click on Manage network connections along the left panel in the window. For
Windows® 7, click on Change adapter settings.
• Right-click on the Local Area Connection which represents your D-Link wireless network adapter which will be
connected to your network.
• Highlight Internet Protocol Version 4 (TCP /IPv4) and click

Properties.
• Click Use the following IP address and enter an IP address that is on

the same subnet as your network or LAN IP address on your router
or network.
Example: If the router’s LAN IP address is 192.168.0.1, make your IP

address 192.168.0.X where X is a number between 2 and 99. Make
sure that the number you choose is not in use on the network.
• Set Default Gateway the same as the LAN IP address of your router
or gateway.
• Set Primary DNS the same as the LAN IP address of your router or
gateway.
• The Secondary DNS is optional (you may enter a DNS server from
your ISP).

Windows® XP Users
• Click on Start > Control Panel. Make sure you are in Classic View. Double-click on the Network Connections icon.

• Right-click on the Local Area Connection which represents your D-Link wireless network adapter (or other adapter)
which will be connected to your router.
• Highlight Internet Protocol (TCP/IP) and click Properties.
• Click Use the following IP address and enter an IP address that is on the same subnet as your network or LAN IP
address on your router.
Example: If the router’s LAN IP address is 192.168.0.1, make your IP address

192.168.0.X where X is a number between 2 and 99. Make sure that the number
you choose is not in use on the network.
• Set Default Gateway the same as the LAN IP address of your router or gateway.
• Set Primary DNS as the LAN IP address of your router or gateway.
• The Secondary DNS is optional (you may enter a DNS server from your ISP).

Appendix C - Technical Specifications
Technical Specifications
Standards Operating Frequency
• IEEE 802.11ac (draft) 5GHz Band:
• IEEE 802.11n • 5.15 ~ 5.25GHz
• IEEE 802.11g • 5.25 ~ 5.35GHz
• IEEE 802.11a • 5.470 ~ 5.725GHz
• IEEE 802.11b
• IEEE 802.3 Media Access Protocol
• IEEE 802.3u • CSMA/CA with ACK
• IEEE 802.3ab
Max Transmitter Output Power
Physical Interface 5GHz Band/VHT-20
• 4 Gigabit Ethernet LAN Ports • 18dBm at MCS0/1/2/3
• 1 Gigabit Ethernet WAN Port • 17dBm at MCS4
• USB 2.0 • 16dBm at MCS5
• 1 WPS Push Button • 15dBm at MCS6
• Reset Button • 14dBm at MCS7
Wireless Interface 5GHz Band/VHT-40

802.11ac (5 GHz) • 18dBm at MCS0/1/2/3
Radio/Modulation • 17dBm at MCS4
• BPSK • 16dBm at MCS5
• QPSK • 15dBm at MCS6
• 16QAM • 14dBm at MCS7
• 64QAM
• 256QAM with OFDM
1 Maximum wireless signal rate derived from IEEE Standard 802.11ac (draft), 802.11a, 802.11g, and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental
factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless
signal range.
2 Frequency Range varies depending on country’s regulation
3 The DIR-850L does not include 5.25-5.35GHz & 5.47-5.725GHz in some regions.

5GHz Band/VHT-80
• 17dBm at MCS0 5GHz Band/HT-40 (TBC)
• 17dBm at MCS1 • -79dBm at MCS0
• 15 dBm at MCS5 • -67dBm at MCS4
• -54dBm at MCS9
Receiver Sensitivity
5GHz Band/HT-20 (TBC) 5GHz Band/HT-80 (TBC)
• -82dBm at MCS0 • -76dBm at MCS0
signal range.

802.11n Transmitter Output Power

Radio/Modulation 5GHz Band/HT-20
• BPSK • 18dBm at MCS0/1/2/3
• QPSK • 17dBm at MCS4
• 16QAM • 16dBm at MCS5
• 64QAM with OFDM • 15dBm at MCS6
• 14dBm at MCS7
Operating Frequency
5GHz Band: 2.4GHz Band/HT-20
• 5.15 ~ 5.25GHz • 19dBm at MCS0/1/2/3
• 5.25 ~ 5.35GHz • 18dBm at MCS4
• 5.470 ~ 5.725GHz • 17dBm at MCS5
• 16dBm at MCS6
2.4GHz ISM Band: • 15dBm at MCS7
• 2400 ~ 2483.5MHz
5GHz Band/HT-40
Channel Numbers • 18dBm at MCS0/1/2/3
• 11 Channels • 17dBm at MCS4
• 16dBm at MCS5
Data Rate • 15dBm at MCS6
• MCS - 0 to MCS -15 • 14dBm at MCS7
Media Access Protocol 2.4GHz Band/HT-40

• CSMA/CA with ACK • 19dBm at MCS0/1/2/3
• 18dBm at MCS4
signal range.

• 17dBm at MCS5 802.11g

• 16dBm at MCS6 Radio/Modulation
• 15dBm at MCS7 • BPSK
• QPSK
Receiver Sensitivity • 16QAM
5GHz and 2.4GHz Band/HT-20 • 64QAM with OFDM
• -82dBm at MCS 0/8
• -79dBm at MCS 1/9 Operating Frequency
• -77dBm at MCS 2/10 2400 ~ 2483.5MHz ISM Band
• -70dBm at MCS 4/12 Channel Numbers
• -66dBm at MCS 5/13 • 11 Channels
• -64dBm at MCS 7/15 Media Access Protocol
• CSMA/CA with ACK
5 GHz and 2.4GHz Band/HT-40
• -79dBm at MCS 0/8 Transmitter Output Power
• -76dBm at MCS 1/9 • 19 +-2dBm at 18,12, 9, 6Mbps
• -74dBm at MCS 2/10 • 18 +-2dBm at 24Mbps
• -61dBm at MCS 7/15 Receiver Sensitivity
• -82dBm at 6Mbps
• -81dBm at 9Mbps
• -79dBm at 12Mbps
signal range.
802.11a Receiver Sensitivity

Radio/Modulation • -82dBm at 6Mbps
• BPSK • -81dBm at 9Mbps
• QPSK • -79dBm at 12Mbps
• 16QAM • -77dBm at 18Mbps
• 64QAM • -74dBm at 24Mbps
• OFDM • -70dBm at 36Mbps
Operating Frequency • -65dBm at 54Mbps
• 5.15 ~ 5.35GHz
• 5.47 ~ 5.725GHz Security
• 5.725 ~ 5.850GHz • Wi-Fi Protected Access (WPA/WPA2)
• WPS™
Channel Numbers
• 24 Non-Overlapping Channels LEDs
• Power/WPS
Media Access Protocol • Internet
• CSMA/CA with ACK
Power
Transmitter Output Power • DC 12V/2A
• 18 +-2dBm at 18,12, 9, 6Mbps
• 17 +-2dBm at 24Mbps Operating Temperature
• 16 +-2dBm at 36Mbps • 30º to 104º F (0º to 40º C)
• 15 +-2dBm at 48Mbps
• 14 +-2dBm at 54Mbps Operating Humidity
• 10% to 90% non-condensing
signal range.

Certifications
• CE
• FCC
• IC
• C-Tick
• CSA International
Dimensions
• 5.75” x 3.40”x 4.40”
Weight
• 0.62 lb
Warranty
• 1-Year Limited Warranty

Appendix D - Contacting Technical Support
Contacting Technical Support

U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.
Before you contact technical support, please have the following ready:
• Model number of the product (e.g. DIR-850L)

• Hardware Revision (located on the label on the bottom of the router (e.g. rev A1))
• Serial Number (s/n number located on the label on the bottom of the router).
You can find software updates and user documentation on the D-Link website as well as frequently asked questions and
answers to technical issues.
For customers within the United States: For customers within Canada:

Phone Support: Phone Support:
(877) 453-5465 (800) 361-5265
Internet Support: Internet Support:

http://support.dlink.com http://support.dlink.ca


Appendix E - GNU General Public License
GPL Code Statement

This D-Link product includes software code developed by third parties, including software code subject to the GNU General Public License (“GPL”)
or GNU Lesser General Public License (“LGPL”). As applicable, the terms of the GPL and LGPL, and information on obtaining access to the GPL
code and LGPL code used in this product, are available to you at:
http://tsd.dlink.com.tw/GPL.asp
The GPL code and LGPL code used in this product is distributed WITHOUT ANY WARRANTY and is subject to the copyrights of one or more
authors. For details, see the GPL code and the LGPL code for this product and the terms of the GPL and LGPL.
WRITTEN OFFER FOR GPL AND LGPL SOURCE CODE
Where such specific license terms entitle you to the source code of such software, D-Link will provide upon written request via email and/or
traditional paper mail the applicable GPL and LGPLsource code files via CD-ROM for a nominal cost to cover shipping and media charges as
allowed under the GPL and LGPL.
Please direct all inquiries to:

Email: [email protected]
Snail Mail:
Attn: GPLSOURCE REQUEST
D-Link Systems, Inc.
17595 Mt. Herrmann Street
Fountain Valley, CA 92708
GNU GENERAL PUBLIC LICENSE

Version 3, 29 June 2007
Copyright (C) 2007 Free Software Foundation, Inc. <http://fsf.org/> Everyone is permitted to copy and distribute verbatim copies of this license
document, but changing it is not allowed.

Preamble
The GNU General Public License is a free, copyleft license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the
GNU General Public License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free
software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other
work released this way by its authors. You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the
freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you
can change the software or use pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain
responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you
received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps:
(1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains that there is no warranty for this free software. For both users’ and authors’
sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of
previous versions.
Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can
do so. This is fundamentally incompatible with the aim of protecting users’ freedom to change the software. The systematic pattern of such abuse
occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of
the GPL to prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision
to those domains in future versions of the GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software
on general-purpose computers, but in those that do, we wish to avoid the special danger that patents applied to a free program could make it
effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification follow.

TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may
be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an
exact copy. The resulting work is called a “modified version” of the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under
applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or
without modification), making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a
computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that
(1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are
provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user
commands or options, such as a menu, a prominent item in the list meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a
work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces
specified for a particular programming language, one that is widely used among developers working in that language.

The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging
a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component,
or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this
context, means a major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable
work runs, or a compiler used to produce the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work)
run the object code and to modify the work, including scripts to control those activities. However, it does not include the work’s System Libraries,
or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of
the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for
shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data communication or
control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
2. Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions
are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is
covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other
equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force.
You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities
for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright.
Those thus making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that
prohibit them from making any copies of your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it
unnecessary.

3. Protecting Users’ Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the
WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention
is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification
of the work as a means of enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in
accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along
with the Program.
You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of
section 4, provided that you also meet all of these conditions:
a) The work must carry prominent notices stating that you modified it, and giving a relevant date.
b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7.
This requirement modifies the requirement in section 4 to “keep intact all notices”.
c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License
will therefore apply, along with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless
of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such
permission if you have separately received it.
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive
interfaces that do not display Appropriate Legal Notices, your work need not make them do so.

A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and
which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate”
if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation’s users beyond what the individual
works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate.
6. Conveying Non-Source Forms.

You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable
Corresponding Source under the terms of this License, in one of these ways:
a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the
Corresponding Source fixed on a durable physical medium customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a
written offer, valid for at least three years and valid for as long as you offer spare parts or customer support for that product
model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the
product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no
more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source
from a network server at no charge.
c) Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative
is allowed only occasionally and noncommercially, and only if you received the object code with such an offer, in accord with
subsection 6b.
d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the
Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the
Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding
Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you
maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts
the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and
Corresponding Source of the work are being offered to the general public at no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be
included in conveying the object code work.

A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or
household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product,
doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical
or common use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses,
or expects or is expected to use, the product. A product is a consumer product regardless of whether the product has substantial commercial,
industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and
execute modified versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must
suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification
has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a
transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of
how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information.
But this requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for
example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates
for a work that has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a
network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and
protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented
(and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or
copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional
permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid
under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but
the entire Program remains governed by this License without regard to the additional permissions.

When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it.
(Additional permissions may be written to require their own removal in certain cases when you modify the work). You may place additional
permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of
that material) supplement the terms of this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or
b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal
Notices displayed by works containing it; or
c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in
reasonable ways as different from the original version; or
d) Limiting the use for publicity purposes of names of licensors or authors of the material; or
e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or
f ) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of
it) with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose
on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received
it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that
term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work
material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that
apply to those files, or a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above
requirements apply either way.

8. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify
it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of
section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until
the copyright holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation
by some reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some
reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure
the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this
License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material
under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring
solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than
this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License.
Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that
work, subject to this License. You are not responsible for enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or
merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of
the work also receives whatever licenses to the work the party’s predecessor in interest had or could give under the previous paragraph, plus a
right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable
efforts.

You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose
a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim
or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any
portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus
licensed is called the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired,
that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims
that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes
the right to grant patent sublicenses in a manner consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor’s essential patent claims, to make, use,
sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent
(such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party
means to make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to
copy, free of charge and under the terms of this License, through a publicly available network server or other readily accessible means, then you
must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this
particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients.
“Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your
recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe
are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work,
and grant a patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy
of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.

A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-
exercise of one or more of the rights that are specifically granted under this License. You may not convey a covered work if you are a party to an
arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the
extent of your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work
from you, a discriminatory patent license (a) in connection with copies of the covered work conveyed by you (or copies made from those copies), or
(b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement,
or that patent license was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be
available to you under applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate
you to collect a royalty for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and
this License would be to refrain entirely from conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version
3 of the GNU Affero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue
to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning
interaction through a network will apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions
will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License
“or any later version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version
published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose
any version ever published by the Free Software Foundation. If the Program specifies that a proxy can decide which future versions of the GNU
General Public License can be used, that proxy’s public statement of acceptance of a version permanently authorizes you to choose that version
for the Program.

Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright
holder as a result of your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO
OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts
shall apply local law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or
assumption of liability accompanies a copy of the Program in return for a fee.

Appendix F - Warranty
Warranty
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:
• Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and
• Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions
or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Limited Warranty:
D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship
and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except
as otherwise stated herein.
• Hardware (excluding power supplies and fans): One (1) year

• Power supplies and fans: One (1) year
• Spare parts and spare kits: Ninety (90) days
The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at
D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual
purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement hardware
need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any
reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware.
Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer,
and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical
to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link
upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded,
shall become the property of D-Link upon replacement or refund.

Limited Software Warranty:

D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications
for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90)
days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its
documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will be
free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will
be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional
specifications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise
agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the
license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject
to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it
is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by
D-Link; provided that the non-conforming Software (and all copies thereof ) is first returned to D-Link. The license granted respecting any Software
for which a refund is given automatically terminates.
Non-Applicability of Warranty:
The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover any
refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or
the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without
any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the
contrary.
Submitting A Claim (USA):

The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and
the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software
nonconformance in sufficient detail to allow DLink to confirm the same, along with proof of purchase of the product (such as a
copy of the dated purchase invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at 1-877-453-5465, who will attempt to assist the
customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a
Return Material Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://
rma.dlink.com/.

• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package
to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package.
Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product
and will not ship back any accessories.
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD
will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped
to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that
are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common
carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise
we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are
prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the
foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to
pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance
with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
Submitting A Claim (Canada):

The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and
the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
• Customers need to provide their receipt (proof of purchase) even if the product is registered. Without a receipt, no warranty service will
be done. The registration is not considered a proof of purchase.
• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance
in sufficient detail to allow D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase
invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at 1-800-361-5265, who will attempt to assist the customer
in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material
Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://rma.dlink.ca/.
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to
ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not
include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship
back any accessories.

• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will
be rejected by D-Link. Products shall be fully insured by the customer and shipped to D-Link Networks, Inc., 2525 Meadowvale Boulevard
Mississauga, Ontario, L5N 5S2 Canada. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired
or replaced packages will be shipped to the customer via Purolator Canada or any common carrier selected by D-Link. Return shipping
charges shall be prepaid by D-Link if you use an address in Canada, otherwise we will ship the product to you freight collect. Expedited
shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product
that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from
the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product
that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or
non-conforming.
• RMA phone number: 1-800-361-5265 Hours of Operation: Monday-Friday, 9:00AM – 9:00PM EST
What Is Not Covered:

The Limited Warranty provided herein by D-Link does not cover:
Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation,
lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number
has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs;
Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act
of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other products or services provided by anyone
other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers,
or the liquidators expressly disclaim their warranty obligation pertaining to the product.
While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link
Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.
Disclaimer of Other Warranties:

EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER
INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY
SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE
LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE
PURCHASER OF THE PRODUCT.

Limitation of Liability:
TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL
OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT
IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK
FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF
THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF
THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM
LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING
EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED
OR STATUTORY.
Governing Law:
This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This
Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state.
Trademarks:
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their
respective owners.
Copyright Statement:
No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the
United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.
Copyright ©2013 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
adequate measures.

FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
Operations in the 5.15-5.25GHz / 5.470 ~ 5.725GHz band are restricted to indoor usage only.
IMPORTANT NOTICE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body. To maintain compliance with FCC RF exposure compliance requirements,
please avoid direct contact to the transmitting antenna during transmitting.
If this device is going to be operated in 5.15 ~ 5.25GHz frequency range, then it is restricted in indoor environment only. This transmitter must not
be co-located or operating in conjunction with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory
to match the intended destination. The firmware setting is not accessible by the end user.

ICC Notice:
Operation is subject to the following two conditions:

1) This device may not cause interference and
2) This device must accept any interference, including interference that may cause undesired operation of the device.

IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This equipment should be installed and operated with minimum distance 20cm between the
radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
(i) The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to
co-channel mobile satellite systems;
(ii) The maximum antenna gain (2dBi) permitted (for devices in the band 5725-5825 MHz) to comply with the e.i.r.p. limits specified
for point-to-point and non point-to-point operation as appropriate, as stated in section A9.2(3).
In addition, users should also be cautioned to take note that high-power radars are allocated as primary users (meaning they have priority) of the
bands 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
Règlement d’Industry Canada

Les conditions de fonctionnement sont sujettes à deux conditions:
(1) Ce périphérique ne doit pas causer d’interférence et.
(2) Ce périphérique doit accepter toute interférence, y compris les interférences pouvant perturber le bon fonctionnement de
ce périphérique.

Appendix G - Registration
Registration
Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.
Version 1.0
April 19, 2013

Dlk0459 - 0 Router Manual

Uploaded by

Copyright:

Available Formats

Dlk0459 - 0 Router Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dlk0459 - 0 Router Manual

Uploaded by

Copyright:

Available Formats

Version 1.

0 | April 19, 2013

Copyright © 2013 by D-Link Systems, Inc.

D-Link DIR-850L User Manual i

D-Link DIR-850L User Manual ii

D-Link DIR-850L User Manual iii

Windows® XP.............................................................................. 129

Contacting Technical Support.......................................151

GPL Code Statement......................................................152

D-Link DIR-850L User Manual iv

DIR-850L Wireless AC1200 Dual Band Cloud Router

Wi-Fi Configuration Card

Quick Install Guide

D-Link DIR-850L User Manual 1

Computer with the following:

• iPhone/iPad/iPod Touch (iOS 3.0 or higher)

D-Link DIR-850L User Manual 2

D-Link DIR-850L User Manual 3

D-Link DIR-850L User Manual 4

D-Link DIR-850L User Manual 5

Before you Begin

D-Link DIR-850L User Manual 6

Wireless Installation Considerations

D-Link DIR-850L User Manual 7

Connect to your Network

D-Link DIR-850L User Manual 8

INTERNET Ethernet Cable Computer

D-Link DIR-850L User Manual 9

D-Link DIR-850L User Manual 10

Connect to an Existing Router

To connect to another router, please follow the steps below:

D-Link DIR-850L User Manual 11

D-Link DIR-850L User Manual 12

D-Link DIR-850L User Manual 13

Quick Setup Wizard

This wizard is designed to guide you through a step-by-step

Click Next to continue.

D-Link DIR-850L User Manual 14

D-Link DIR-850L User Manual 15

D-Link DIR-850L User Manual 16

Create a wireless security passphrase or key (between 8-63 characters).

Click Next to continue.

In order to secure your router, please enter a new password. Check

D-Link DIR-850L User Manual 17

If you clicked Yes, a window may appear (depending on what web

D-Link DIR-850L User Manual 18

If you do not want to register at this time, click Cancel.

D-Link DIR-850L User Manual 19

PC and Mac users can use the mydlink portal at http://mydlink.com.

D-Link DIR-850L User Manual 20

QRS Mobile App

You may also scan this code to download.

Connect to the router wirelessly by going to your wireless utility

on your device. Scan for the wireless network name (SSID) as

D-Link DIR-850L User Manual 21

SharePort Mobile App

1. Insert your USB flash drive into DIR-850L.

3. From your iOS mobile device, click Settings.

D-Link DIR-850L User Manual 22